有源循环式光脉冲复制系统的输出特性研究

改进并验证了一种基于有源循环光纤延迟线的模拟光脉冲信号复制技术.实验系统采用低增益掺铒光纤放大器补偿循环损耗.进行了光脉冲信号复制的仿真和实验,在掺铒光纤放大器增益为6.774 dB,光滤波器－3 dB,带宽为0.8 nm时,测得第500个复制光脉冲的信噪比为31 dB.仿真和实验结果表明,选用小增益掺铒光纤放大器可以实现低于3 dB的噪音系数,降低掺铒光纤放大器的放大自发辐射噪音并提高输出脉冲序列的信噪比,有望成为提高光脉冲复制器性能的一种新方法.在系统中插入窄带光滤波器等手段也是改善信噪比的有效措施.     

Multi-wavelength fiber laser based on nonlinear polarization rotation in semiconductor optical amplifier and photonic crystal fiber

A nonlinear polarisation rotation (NPR) based multi-wavelength laser source is demonstrated using a semiconductor optical amplifier (SOA) and photonic crystal fiber (PCF). The SOA acts as not only the gain medium but also the phase retarder for multi-wavelength oscillation in conjunction with an isolator. The incorporation of PCF improves the NPR effect and thus assists in the multiwavelength generation. The wavelength spacing reduces from 4.82 to 2.76 nm as the PCF length increases from 50 to 100 m. With a 100 m long PCF, the proposed laser produces at least 42 lasing wavelengths with optical signal to noise ratio of more than 10 dB.     

Double-pumped multiwavelength fiber optical parametric oscillator based on a Sagnac loop filter

We propose a double-pumped ring cavity multiwavelength fiber optical parametric oscillator (MW-FOPO) using a highly nonlinear dispersion-shifted fiber (HNL-DSF) as the gain medium and a polarization maintained fiber based Sagnac loop filter as the comblike filter. 22-wavelength lasing of the double-pumped MW-FOPO with a ripple less than ±2.5 dB and a wavelength spacing of about 0.8 nm in a wavelength range from 1541 nm to 1558 nm is experimentally demonstrated. We discussed the power stability of the multiwavelength lasing of the double-pumped MW-FOPO. A comparison of the output spectra between the double-pumped MW-FOPO and single-pumped MW-FOPO is also presented.     

A novel frequency sextupling scheme for optical mm-wave generation utilizing an integrated dual-parallel Mach-Zehnder modulator

A novel scheme is proposed for frequency sextupling mm-wave generation based on a laser and an integrated dual-parallel Mach-Zehnder modulator (MZM) without optical filter. Theoretical analysis is presented to suppress the undesired optical sidebands for the high quality generation of frequency sextupling mm-wave signal. The performance of the proposed scheme is evaluated by simulations. Utilizing the integrated MZM consisted of two sub-MZMs with extinction ratio of 30 dB, the optical sideband suppression ratio (OSSR) is as high as 29.9 dB and the radio frequency spurious suppression ratio (RFSSR) exceeds 24 dB without any optical or electrical filter. The impact of the nonideal RF driven voltage and phase difference of RF driven signal applied to two sub-MZMs of the integrated MZM on OSSR and RFSSR is discussed and analyzed. After transmission over fiber, the generated optical mm-wave signal demonstrates good performance. Furthermore, the performance of two cases for the proposed scheme is also compared.     

Multiwavelength erbium-doped fiber laser employing a nonlinear optical loop mirror

A stable and broad bandwidth multiwavelength erbium-doped fiber laser is proposed and demonstrated successfully. A nonlinear optical loop mirror which induces wavelength-dependent cavity loss and behaves as an amplitude equalizer is employed to ensure stable room-temperature multiwavelength operation. Up to 50 wavelengths lasing oscillations with wavelength spacing of 0.8 nm within a 3-dB spectral range of 1562-1605 nm has been achieved. The measured power fluctuation of each wavelength is about 0.1 dB within a 2-h period.     

High-speed photonically assisted analog-to-digital conversion using a continuous wave multiwavelength source and phase modulation

A more simple photonically assisted analog-to-digital conversion system utilizing a cw multiwavelength source and phase modulation instead of a mode-locked laser is presented. The output of the cw multiwavelength source is launched into a dispersive device (such as a single-mode fiber). This fiber creates a pulse train, where the central wavelength of each pulse corresponds to a spectral line of the optical source. The pulses can then be either dispersed again to perform discrete wavelength time stretching or demultiplexed for continuous time analog-to-digital conversion. We experimentally demonstrate the operation of both time stretched and interleaved systems at 38 GHz. The potential of integrating this type of system on a monolithic chip is discussed.     

Flattening effect of four wave mixing on multiwavelength Brillouin-erbium fiber laser

A multiwavelength Brillouin-erbium fiber laser with enhanced output uniformity is demonstrated and its performance with and without the assistance of four wave mixing (FWM) is compared. The presence of FWM effect is proven by the generation of anti-Stokes wave and higher-order Stokes wave. This scheme is successful in flattening the multiwavelength output. At Brillouin pump wavelength of 1,550 nm, between the first and the last output channel, peak power differences of 4.59 and 8.32 dB are recorded for the scheme with and without the assistance of FWM, respectively. This represents 3.73 dB improvement in the multiwavelength output power uniformity.     

Multiwavelength fiber laser using S-band erbium-doped fiber amplifier and semiconductor optical amplifier

A multiwavelength fiber ring laser that is based on an S-band erbium-doped fiber amplifier (EDFA) and a semiconductor optical amplifier (SOA) is developed. An optical switch is used to switch the multiwavelength fiber laser between S-band and L-band. This fiber laser can stably lase seven wavelengths in the S-band or 28 wavelengths in the L-band. Additionally, the lasing wavelengths with a signal-to-noise ratio of over 33 dB and a wavelength spacing of 100 GHz are demonstrated experimentally. The average powers of the lasing wavelength in the S-band and the L-band are −7.53 and −12.15 dBm, respectively.     

Time- and wavelength-interleaved optical pulse train generation based on dispersion spreading and sectional compression

A method to generate time- and wavelength-interleaved optical pulse trains based on dispersion spreading and sectional compression is proposed and demonstrated. A 4×2 GHz time- and wavelength-interleaved pulse train is generated from an input 2 GHz mode-locked pulse train. The advantages of the proposed scheme are its simplicity and robustness, since no microwave component or multiwavelength laser source is required. In addition, we demonstrate supercontinuum generation of an ultraflat 18 nm bandwidth spectrum with less than 0.5 dB fluctuation over the 3.2 nm central bandwidth.     

基于非线性光纤环形镜的少模脉冲幅度调制再生器

随着网络带宽需求的快速增加,波分复用系统的容量已接近非线性香农极限.为了适应未来网络的发展,空分复用技术引起了越来越多的关注.本文首次提出基于少模非线性光纤环形镜(FM-NOLM)的脉冲幅度调制(PAM)全光再生器,描述了其工作原理和具体设计过程.采用COMSOL软件对组成FM-NOLM的硫化物高非线性光纤进行了模式特性仿真.以LP01,LP11,LP21三个光纤模式为例,确定了再生器的参数,计算出每个模式的功率转移函数曲线.仿真分析了该少模PAM-4全光再生器的噪声抑制(NRR)性能,并与单模情形进行了比较.研究表明,1)对于每个空间模式的PAM信号,所有再生电平具有一致的功率转移性能;2)当输入信噪比(SNR)约大于20 dB时,三种模式的噪声抑制比均可超过3 dB,并随着输入信噪比线性增加,其斜率约为1.2;3)在相同输入SNR条件下,三种模式的噪声抑制比相差不大,不超过1.1 dB.为了说明再生器的再生性能,当输入SNR为25 dB时,我们还给出了再生前后PAM-4信号的功率分布直方图.与现有的再生方案相比,本文方案的均匀多电平再生转移性能,使其更适合高频谱效率的长距空分复用系统和任意电平数的PAM信号再生.此外,该方案也能够扩展到波长域,有效提高光通信系统的传输容量.     

Frequency-modulation-mode-locked optical parametric oscillator

We demonstrate a novel technique for the generation of mode-locked pulses from a continuous-wave (cw) optical parametric oscillator (OPO). The technique is based on the deployment of a phase modulator in combination with an antiresonant ring interferometer internal to a cw OPO, simultaneously providing spectral broadening and phase-to-amplitude feedback modulation. The scheme is implemented in a doubly-resonant cw OPO based on MgO:sPPLT, configured in a standing-wave cavity and pumped at 532 nm. With the phase modulator activated and the cavity length synchronized, a stable train of 800 ps pulses is generated at a repetition rate of 160 MHz. Using single-pass second harmonic generation (SHG) of the OPO output, we observe a four times enhancement in SHG compared with cw operation, confirming the real achievement of energy concentration as a result of mode-locked operation.     

Improved stabilization of a 1.3 microm femtosecond optical frequency comb by use of a spectrally tailored continuum from a nonlinear fiber grating

We report significant enhancement (+24 dB) of the optical beat note between a 657 nm cw laser and the second-harmonic generation of the tailored continuum at 1314 nm generated with a femtosecond Cr:forsterite laser and a nonlinear fiber Bragg grating. The same continuum is used to stabilize the carrier-envelope offset frequency of the Cr:forsterite femtosecond laser and permits improved optical stabilization of the frequency comb from 1.0 to 2.2 microm. Using a common optical reference at 657 nm, a relative fractional frequency instability of 2.0 x 10(-15) is achieved between the repetition rates of Cr:forsterite and Ti:sapphire laser systems in 10 s averaging time. The fractional frequency offset between the optically stabilized frequency combs of the Cr:forsterite and Ti:sapphire lasers is +/-(0.024 +/- 6.1) x 10(-17).     

基于非线性偏振旋转效应的多波长光纤激光器

多波长光纤激光器是未来波分复用光通信系统的理想光源,提出和展示了一个基于非线性偏振旋转效应的多波长光纤激光器,非线性偏振旋转诱导的强度相关非均匀损耗能有效地抑制均匀加宽增益介质掺铒光纤中的模式竞争,从而使光纤激光器在室温下产生稳定的多波长输出,实验实现了最多18个波长的多波长输出.另外,此激光器没有使用传统的滤波器,而是在激光腔内插入一段保偏光纤,保偏光纤与偏振相关隔离器构成一等效Lyot双折射光纤周期性滤波器.利用这种在线型的双折射光纤滤波器简化了光纤激光器的结构,使它更易于集成.还实验研究了多波长输出随抽运功率的演化,发现抽运功率对多波长的均匀性影响很大.     

Coherent transfer of an optical carrier over 251 km

We transfer an optical frequency over 251 km of optical fiber with a residual instability of 6x10(-19) at 100 s. This instability and the associated timing jitter are limited fundamentally by the noise on the optical fiber and the link length. We give a simple expression for calculating the achievable instability and jitter over a fiber link. Transfer of optical stability over this long distance requires a highly coherent optical source, provided here by a cw fiber laser locked to a high finesse optical cavity. A sufficient optical carrier signal is delivered to the remote fiber end by incorporating two-way, in-line erbium-doped fiber amplifiers to balance the 62 dB link loss.     

Multiwavelength fiber laser with ultradense wavelength spacing based on inhomogeneous loss with assistance of nonlinear polarization rotation

We demonstrate a multiwavelength fiber laser with ultradense wavelength spacing and ultrabroad bandwidth based on inhomogeneous loss mechanism with assistance of nonlinear polarization rotation. The inhomogeneous loss, implemented by incorporating a section of highly nonlinear fiber (HNLF) and a Sagnac filter in the laser cavity, can balance mode competition in erbium-doped fiber and result in ultradense multiwavelength generation. The bandwidth of the multiwavelength spectrum is greatly broadened owing to the intensity-dependent loss induced by nonlinear polarization rotation. Stable multiwavelength lasing with wavelength spacing of 0.08 nm and wavelength number up to 254 is achieved at room temperature. Moreover, multiwavelength tuning is realized through modifying polarization-dependent cavity loss.     

Multiwavelength fiber ring lasing by use of a semiconductor optical amplifier

A multiwavelength fiber ring laser obtained by use of a semiconductor optical amplifier (SOA) with a simple laser cavity configuration is reported. A Fabry-Perot filter was used in the fiber laser ring cavity to achieve more than 50 simultaneous wavelength lasing oscillations with a frequency separation of 50 GHz. The resulting stable broadband multiwavelength lasing operation was attributed to broadband and flat gain of the SOA, which has a gain flatness of 0.8 dB for more than 20 nm. The laser has a total output power of -3 dBm and a signal-to-spontaneous-noise ratio of 30 dB.     

Flat optical frequency comb generation using polarization modulator and frequency shifter with double recirculating frequency shifting loops

A scheme to generate ultra-flat and stable optical frequency comb (OFC) based on multi-wavelength optical seed source and polarization-modulator-based complementary frequency shifter (PCFS) has been proposed and demonstrated. The OFC generation scheme includes two stages: 5-carrier light source is generated by utilizing a polarization modulator at the first stage, and the light source is then used as the seed light in the PCFS at the second stage. Compared with the previous flat OFC generator based on a recirculation frequency shifter, the proposed scheme can greatly reduce the recirculation times, and such a property makes the accumulated noise of the system enormously decrease. In order to achieve the frequency comb with the best flatness, the optical amplifier gain, filter stop-band attenuation and modulator drive voltage are optimized. Experiment simulations show that high-quality OFC with hundreds of frequency lines and power fluctuation within 2 dB can be achieved without direct-current bias control and wavelength-selective-switch.     

Stable multiwavelength fiber ring laser with equalized power spectrum based on a semiconductor optical amplifier

We experimentally demonstrated a new structure of a multiwavelength semiconductor optical amplifier (SOA) ring laser based on a fiber Sagnac loop filter that can generate up to 25 stable output lasing wavelengths at room temperature. By varying the length of a polarization-maintaining (PM) fiber within the Sagnac loop filter, the wavelength spacing between the output lasing wavelengths can be changed to a desired value. By tuning a polarization controller (PC) within the Sagnac loop filter, stable multiwavelength 1550-nm operation with up to 17 lasing lines within 3 dB power level variation and with a wavelength spacing of ∼0.8 nm was achieved. The optical signal-to-noise ratios (OSNRs) of all the lasing wavelengths are greater than 40 dB.     

Optical wavelet de-noising applied in multi-span nonlinear fiber links

In this work, optical wavelet de-noising with several different types of wavelets such as db4, coif4 and dmey wavelet was applied at the end of the 40 Gbit/s multi-span intensity-modulated fiber communication systems. The results of numerical simulations carried out in different fiber links demonstrated that the optical wavelet de-noising method could remove the random amplitude fluctuation induced by the interaction of EDFA’s ASE noise and optical fiber’s dispersion and nonlinearity. The SNR and BER curves of the optical bit sequence without and with optical wavelet de-noising in dispersion compensation fiber link were plotted to show the effectiveness of the wavelet de-noising in the fiber-optic communication systems and wavelet de-noising with demy wavelet can achieve better result than with other type wavelet.     

Continuously wavelength-spacing-tunable and idler-output multiwavelength fiber optical parametric oscillator

We demonstrate a continuously wavelength-spacing-tunable and high-power multiwavelength fiber optical parametric oscillator based on the multiwavelength idler-output technique. The laser cavity for multiwavelength idler outputs is constructed by a pumped highly-nonlinear dispersion-shifted fiber as parametric gain medium, two highly-reflective chirped fiber Bragg gratings (CFBGs) and a superimposed CFBG as comb-like filter. At a pump power of 1.1 W, the idler output of 10 wavelengths around 1.56 μm is achieved with a wavelength spacing of 0.39 nm. The wavelength spacing can be continuously tuned from 0.39 to 1.0 nm by utilizing a cantilever beam-based chirp tuning method to change the FSR of the superimposed CFBG. Our experimental results show that the designed multiwavelength idler-output scheme can significantly increase the multiwavelength output power with a total output power of 98 mW and each idler-channel power of 16.3 mW.