Study on morphology and photoluminescence of Au/SiO2 nanocomposite films

Au/SiO₂ nanocomposite films were fabricated on Si (111) substrates by radio frequency (RF) magnetron sputtering technique and annealing at different temperature for 20 min (mode A) and at 1000 °C for different annealing time (mode B). The nanocomposite films were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and photoluminescence (PL). SEM results demonstrate that the size of Au crystallites in mode A first increases and then decreases, on increasing annealing temperature, according to the results of XRD spectra. Analysis of PL spectra in mode B shows that the intensity of the emission peak at 440 nm and 523 nm early increases and late decreases, with increasing annealing time at 1000 °C. The origin of the emission peak at around 440 nm was related to the size and quantity of Au particles and one of the emission peak at around 523 nm was related to the nanostructure of films in agreement with SEM imagines. Experimental results indicated that morphology, microstructure and luminescence of Au/SiO₂ nanocomposite films showed close affinity with annealing temperature and annealing time.     

Au/SiO2纳米多层薄膜的制备及其性质表征

利用多靶磁控溅射技术制备了Au/SiO₂纳米颗粒分散氧化物多层复合薄膜.研究了在保持Au单层颗粒膜沉积时间一定时薄膜厚度一定、变化SiO₂的沉积时间及SiO₂的沉积时间一定而改变薄膜厚度时，多层薄膜在薄膜厚度方向的微观结构对吸收光谱的影响.研究结果表明：具有纳米层状结构的Au/SiO₂多层薄膜在560 nm波长附近有明显的表面等离子共振吸收峰，吸收峰的强度随Au颗粒的浓度增加而增强，在Au颗粒浓度相同的情况下，复合薄膜 关键词： 2纳米复合薄膜')" href="#">Au/SiO₂纳米复合薄膜 多靶磁控溅射 吸收光谱 有效介质理论     

Enhanced nonlinear optical absorption of Au/SiO2 nano-composite thin films

Nano metal-particle dispersed glasses are the attractive candidates for nonlinear optical material applications.Au/SiO 2 nano-composite thin films with 3 vol% to 65 vol% Au are prepared by inductively coupled plasma sputtering.Au particles as perfect spheres with diameters between 10 nm and 30 nm are uniformly dispersed in the SiO 2 matrix.Optical absorption peaks due to the surface plasmon resonance of Au particles are observed.The absorption property is enhanced with the increase of Au content,showing a maximum value in the films with 37 vol% Au.The absorption curves of the Au/SiO 2 thin films with 3 vol% to 37 vol% Au accord well with the theoretical optical absorption spectra obtained from Mie resonance theory.Increasing Au content over 37 vol% results in the partial connection of Au particles,whereby the intensity of the absorption peak is weakened and ultimately replaced by the optical absorption of the bulk.The band gap decreases with Au content increasing from 3 vol% to 37 vol % but increases as Au content further increases.     

XPS investigation of diffusion of two-layer ZrO2/SiO2 and SiO2/ZrO2 sol–gel films

Two-layer ZrO₂/SiO₂ and SiO₂/ZrO₂ films were deposited on K9 glass substrates by sol–gel dip coating method. X-ray photoelectron spectroscopy (XPS) technique was used to investigate the diffusion of ZrO₂/SiO₂ and SiO₂/ZrO₂ films. To explain the difference of diffusion between ZrO₂/SiO₂ and SiO₂/ZrO₂ films, porous ratio and surface morphology of monolayer SiO₂ and ZrO₂ films were analyzed by using ellipsometry and atomic force microscopy (AFM). We found that for the ZrO₂/SiO₂ films there was a diffusion layer with a certain thickness and the atomic concentrations of Si and Zr changed rapidly; for the SiO₂/ZrO₂ films, the atomic concentrations of Si and Zr changed relatively slowly, and the ZrO₂ layer had diffused through the entire SiO₂ layer. The difference of diffusion between ZrO₂/SiO₂ and SiO₂/ZrO₂ films was influenced by the microstructure of SiO₂ and ZrO₂.     

Preparation and characterization of novel Pd/SiO2 and Ca-Pd/SiO2 egg-shell catalysts with porous hollow silica

Novel egg-shell structured monometallic Pd/SiO₂ and bimetallic Ca-Pd/SiO₂ catalysts were prepared by an impregnation method using porous hollow silica (PHS) as the support and PdCl₂ and Ca(NO₃)₂·4H₂O as the precursors. It was found from transmission electron microscope (TEM), scanning electron microscope (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD) that Pd was loaded on PHS with a particle size of 5-12 nm in Pd/SiO₂ samples and the Pd particle size in Ca-Pd/SiO₂ was smaller than that in Pd/SiO₂ since Ca could prevent Pd particles from aggregating. X-ray photoelectron spectroscopy (XPS) analyses exhibited that Pd 3d_5/2 binding energies of Pd/SiO₂ and Ca-Pd/SiO₂ were 0.2 and 0.9 eV lower than that of bulk Pd, respectively, as a result of the shift of the electron cloud from Pd to oxygen in Pd/SiO₂ and to both oxygen and Ca in Ca-Pd/SiO₂. The activity of Ca-Pd/SiO₂ egg-shell catalyst for CO hydrogenation and the selectivity to methanol, with a value of 36.50 mmol_CO mol⁻¹_Pd s⁻¹ and 100%, respectively, were much higher than those of the catalysts prepared with traditional silica gel as the support, owing to the porous core-shell structure of the PHS support.     

Preparation and characterization of amine-functionalized SiO2/TiO2 films for formaldehyde degradation

This paper investigated the gaseous formaldehyde degradation by the amine-functionalized SiO₂/TiO₂ photocatalytic films for improving indoor air quality. The films were synthesized via the co-condensation reaction of methyltrimethoxysilane (MTMOS) and 3-aminopropyltrimethoxysilane (APTMS). The physicochemical properties of prepared photocatalysts were characterized with N₂ adsorption/desorption isotherms measurement, X-ray diffraction (XRD) and Fourier Transform Infrared spectroscopy (FT/IR). The effect of amine-functional groups and the ratio of MTMOS/APTMS precursors on the formaldehyde adsorption and photocatalytic degradation were investigated. The results showed that the formaldehyde adsorption and photocatalytic degradation of the APTMS-functionalized SiO₂/TiO₂ film was higher than that of SiO₂/TiO₂ film due to the surface adsorption on amine sites and the relatively high of the specific surface area of the APTMS-functionalized SiO₂/TiO₂ film (15 times higher than SiO₂/TiO₂). The enhancement of the formaldehyde degradation of the film can be attributed to the synergetic effect of adsorption and subsequent photocatalytic decomposition. The repeatability of photocatalytic film was also tested and the degradation efficiency was 91.0% of initial efficiency after seven cycles.     

Ag-Au合金/SiO$lt;sub$gt;2$lt;/sub$gt;复合薄膜的制备与表征

以AgNO₃,HAuCl₄和正硅酸乙酯为主要原料,利用溶胶-凝胶法和旋涂技术,通过热处理和紫外光辐射还原得到了不同n_Ag/n_Au（1∶0,2∶1,1∶2,0∶1）的Ag-Au合金/SiO₂复合薄膜.从扫描电子显微镜和X射线衍射谱的结果可以看出得到的薄膜均匀性好,复合薄膜中合金颗粒的尺寸为10 nm左右.利用紫外-可见分光光谱仪研究了复合薄膜的光吸收性能,结果表明,随着n_Ag/n_Au的降低,吸收峰的位置也由最初的Ag纳米粒子的等离子共振吸收峰430 nm附近,逐渐红移到Au纳米粒子的等离子共振吸收峰605和880 nm附近.从光吸收谱可以看出,n_Ag∶n_Au＝2∶1和1∶2的两个样品分别在515,730 nm附近和550,730 nm附近出现表面等离子共振吸收峰.这表明Au-Ag合金固溶体的形成. 关键词： 2')" href="#">Ag-Au合金/SiO₂ 紫外辐射 光吸收性能     

Electroluminescence from Si／SiO2 films deposited on p—Si substrates

The structure of Au/Si/SiO₂/p-Si has been fabricated using the magnetron sputtering technique. It has a very good rectifying behaviour. Visible electroluminescence (EL) has been observed from the Au/Si/SiO₂/p-Si structure at a forward bias of 5V or larger. A broad band with one peak around 650－660 nm appears in all the EL spectra of the structure. The effects of the thickness of the Si layer in the Si/SiO₂ films and of the input electrical power on EL spectra are studied systematically.     

Size-selected Au clusters deposited on SiO2/Si: Stability of clusters under ambient pressure and elevated temperatures

This study examined the oxidation and reduction behavior of mass-selected Au clusters consisting of 2-13 atoms deposited on silica. An atomic oxygen environment was used for the oxidation of Au. X-ray photoelectron spectroscopy (XPS) was used to identify Au(III) and Au(O). Au₅, Au₇ and Au₁₃ clusters deposited on the as-prepared SiO₂/Si substrates were highly inert towards oxidation, whereas the other clusters could be oxidized, i.e. the chemical property drastically changed with the number of atoms in a cluster. The size-selectivity in chemical reactivity remained unchanged upon air-exposure. The chemical properties of the deposited Au clusters were unchanged after annealing at 250 °C. Annealing at higher temperatures caused structural changes to the surface, as determined by the oxidation behavior. XPS of the deposited Au clusters upon annealing indicated charge transfer from Au to silica.     

Preparation and characterization of SiO2/ZrO2/Ag multicoated microspheres

A new type of multicoated silica/zirconia/silver (SiO₂/ZrO₂/Ag) core-shell composite microspheres is synthesized in this paper. In the process, ZrO₂-decorated silica (SiO₂/ZrO₂) core-shell composites were firstly fabricated by the modification of zirconia on silica microspheres through the hydrolysis of zirconium precursor. Subsequently, on SiO₂/ZrO₂ composite cores, silver nanoparticles were introduced via ultrasonic irradiation and acted as “Ag seeds” for the formation of integrate silver shell by further reduction of silver ions using formaldehyde as reducer. The resulting samples were characterized by transmission electron microscopy, X-ray diffraction, Fourier-transform infrared, energy-dispersive X-ray, and UV-vis spectroscopy, indicating that zirconia and silver layers were successfully coated on the surfaces of silica microspheres.     

Fabrication and characterization of Au/SiO2 nanocomposite films

Au/SiO₂ nanocomposite films were prepared by radio frequency sputtering technique and annealing. The above nanocomposite films were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), and atomic force microscopy (AFM). The surface of the nanocomposite films was uniform with the particle diameter of 100-300 nm. The size of Au crystallites increased on increasing annealing time. The luminescent behavior of the nanocomposite films was characterized by photoluminescence (PL) with different excitation wavelengths. Two emission peaks at around 525 nm and 560 nm were observed with the excitation wavelength at 325 nm. An intensive emission peak at around 325 nm was observed with the excitation wavelength at 250 nm, which is related to the defective structure of the amorphous SiO₂ layer because of oxygen deficiency, and could be applied to many fields, such as ultraviolet laser and ultraviolet detector.     

Dielectric properties of barium titanate ceramics modified by SiO2 and by BaO-SiO2

The influence of SiO₂ on the dielectric properties of barium titanate ceramics was investigated. SiO₂ had been doped solely and together with BaO into barium titanate before calcination. X-ray diffraction showed that all the ceramics were of a pure perovskite phase after sintering at 1275 °C for 2 h. For SiO₂-doping, there was about 2.5 °C increase in Curie temperature per molar percentage of doping and the leakage current was obviously increased, especially at low voltages for relatively high doping levels. While for the co-doping of SiO₂ and BaO, there was little change in Curie temperature. The point defects formed through the dopings were proposed responsible for the effects. It was suggested that SiO₂ is important to barium titanate ceramics not only for sintering but also for modifying their properties.     

同步辐射光激励的二氧化硅薄膜刻蚀研究

利用热氧化法在硅晶片上生长SiO₂薄膜，结合光刻和磁控溅射技术在SiO₂薄膜表面制备接触型钴掩模，通过掩模方法在硅表面开展了同步辐射光激励的表面刻蚀研究，在室温下制备了SiO₂薄膜的刻蚀图样.实验结果表明：在同步辐射光照射下，通入SF₆气体可以有效地对SiO₂薄膜进行各向异性刻蚀，并在一定的气压范围内，刻蚀率随SF₆气体浓度的增加而增加，随样品温度的下降而升高；如果在同步辐射光照射下，用SF₆和O₂的混合气体作为反应气体，刻蚀过程将停止在SiO₂/Si界面，即不对硅刻蚀，实现了同步辐射对硅和二氧化硅两种材料的选择性刻蚀；另外，钴表现出强的抗刻蚀能力，是一种理想的同步辐射光掩模材料. 关键词： 同步辐射刻蚀 接触型钴掩模 二氧化硅薄膜     

The electrical properties of dielectric stacks of SiO2 and Al2O3 prepared by atomic layer deposition method

We produced dielectric stacks composed of ALD SiO₂ and ALD Al₂O₃, such as SiO₂/Al₂O₃, Al₂O₃/SiO₂, and SiO₂/Al₂O₃/SiO₂, and measured the leakage currents through the stacks in comparison with those of the single oxide layers. SiO₂/Al₂O₃ shows lowest leakage current for negative bias region below 6.4 V, and Al₂O₃/SiO₂ showed highest current under negative biases below 4.5 V. Two distinct electron conduction regimes are observed for Al₂O₃ and SiO₂/Al₂O₃. Poole-Frenkel emission is dominant at the high-voltage regime for both dielectrics, whereas the direct tunneling through the dielectric is dominant at the low-voltage regime. The calculated transition voltage between two regimes for SiO₂ (6.5 nm)/Al₂O₃ (12.6 nm) is −6.4 V, which agrees well with the experimental observation (−6.1 V). For the same EOT of entire dielectric stack, the transition voltage between two regimes decreases with thinner SiO₂ layer.     

Novel catalysts: Indium implanted SiO2 thin films

Interactions of Indium (In) and silicon (Si) atoms are known to catalyze certain organic chemical reactions with high efficiency. In an attempt of creating a material that manifests the interactions, In implanted SiO₂ thin films were prepared by ion beam injection and their catalytic abilities for organic chemical reactions were examined. It has been found that, with an injection energy of approximately 0.5 keV, a thin In film is formed on a SiO₂ substrate surface and the In implanted SiO₂ thin film can catalyze an organic chemical reaction. It has been also shown that there is an optimal ion dose for the highest catalytic ability in the film preparation process. Thin-film-type catalyzing materials such as the one proposed here may open a new way to enhance surface chemical reaction rates.     

Synthesis and characterization of polyurethane/SiO2 nanocomposites

In order to achieve good dispersion of nano-SiO₂ and increase the interactions between nano-SiO₂ and PU matrix, nano-SiO₂ was firstly modified with poly(propylene glycol) phosphate ester (PPG-P) which was a new polymeric surfactant synthesized through the esterification of poly(propylene glycol) (PPG) and polyphosphoric acid (PPA). Then a series of polyurethane (PU)/SiO₂ nanocomposites were prepared via in situ polymerization. The surface modification of nano-SiO₂, the microstructure and the properties of nanocomposites were investigated by FTIR, SEM, XRD and TGA. It was found that good dispersion of nano-SiO₂ achieved in PU/SiO₂ nanocomposite after the modification with PPG-P. The segmented structures of PU were not interfered by the presence of nano-SiO₂ in these nanocomposites.     

Core/shell structured ZnO/SiO2 nanoparticles: Preparation, characterization and photocatalytic property

ZnO nanoparticles were prepared by a simple chemical synthesis route. Subsequently, SiO₂ layers were successfully coated onto the surface of ZnO nanoparticles to modify the photocatalytic activity in acidic or alkaline solutions. The obtained particles were characterized by Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), transmission electron microscopy (TEM), energy dispersive spectrometry (EDS) and zeta potential. It was found that ultrafine core/shell structured ZnO/SiO₂ nanoparticles were successfully obtained. The photocatalytic performance of ZnO/SiO₂ core/shell structured nanoparticles in Rhodamine B aqueous solution at varied pH value were also investigated. Compared with uncoated ZnO nanoparticles, core/shell structured ZnO/SiO₂ nanoparticles with thinner SiO₂ shell possess improved stability and relatively better photocatalytic activity in acidic or alkaline solutions, which would broaden its potential application in pollutant treatment.     

Deposition of Au/TiO2 film by pulsed laser

Au nanoparticles, which were photoreduced by a Nd:YAG laser in HAuCl₄ solution containing TiO₂ colloid and accompanied by the TiO₂ particles, were deposited on the substrate surface. The film consisting of Au/TiO₂ particles was characterized by the absorption spectra, scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis. The adhesion between the film and substrate was evaluated by using adhesive tape test. It was found that the presence of TiO₂ dramatically enhanced the adhesion strength between the film and the substrate, as well as the deposition rate of film. The mechanism for the deposition of Au/TiO₂ film was also discussed.     

Coupling between Ge-nanocrystals and defects in SiO2

Room temperature photoluminescence (PL) at around 600 nm from magnetron-sputtered SiO₂ films co-doped with Ge is reported. The PL signal is observed in pure SiO₂, however, its intensity increases significantly in the presence of Ge-nanocrystals (Ge-nc). The PL intensity has been optimized by varying the temperature of heat treatment, type of gas during heat treatment, concentration of Ge in the SiO₂ films, and gas pressure during deposition. Maximum intensity occurs when Ge-nc of around 3.5 nm are present in large concentration in SiO₂ layers deposited at fairly high gas pressure. Based on time resolved PL, and PL measurements after α-particle irradiation or H passivation, we attribute the origin of the PL to a defect in SiO₂ (probably an O deficiency) that is excited through an energy transfer from Ge-nc. There is no direct PL from the Ge-nc; however, there is a strong coupling between excitons created in the Ge-nc and the SiO₂ defect.     

Characterization of TiO2/Au/TiO2 films deposited by magnetron sputtering on polycarbonate substrates

Transparent and conducting TiO₂/Au/TiO₂ (TAuT) films were deposited by reactive magnetron sputtering on polycarbonate substrates to investigate the effect of the Au interlayer on the optical, electrical, and structural properties of the films. In TAuT films, the Au interlayer thickness was kept at 5 nm. Although total thickness was maintained at 100 nm, the stack structure was varied as 50/5/45, 70/5/25, and 90/5/5 nm.In XRD pattern, the intermediate Au films were crystallized, while all TAuT films did not show any diffraction peaks for TiO₂ films with regardless of stack structure. The optical and electrical properties were dependent on the stack structure of the films. The lowest sheet resistance of 23 Ω/□ and highest optical transmittance of 76% at 550 nm were obtained from TiO₂ 90 nm/Au 5 nm/TiO₂ 5 nm films. The work function was dependent on the film stack. The highest work function (4.8 eV) was observed with the TiO₂ 90 nm/Au 5 nm/TiO₂ 5 nm film stack. The TAuT film stack of TiO₂ 90 nm/Au 5 nm/TiO₂ 5 nm films is an optimized stack that may be an alternative candidate for transparent electrodes in flat panel displays.