H2O interaction with clean and oxygen precovered Ni(110)

The interaction of water vapour with clean as well as with oxygen precovered Ni(110) surfaces was studied at 150 and 273 K, using UPS, ΔΦ, TDS, and ELS. The He(I) (He(II)) excited UPS indicate a molecular adsorption of H₂O on Ni(110) at 150 K, showing three water-induced peaks at 6.5, 9.5 and 12.2 eV below E_F (6.8, 9.4 and 12.7 eV below E_F). The dramatic decrease of the Ni d-band intensity at higher exposures, as well as the course of the work function change, demonstrates the formation of H₂O multilayers (ice). The observed energy shift of all water-induced UPS peaks relative to the Fermi level (ΔE_max = 1.5 eVat 200 L) with increasing coverage is related to extra-atomic relaxation effects. The activation energies of desorption were estimated as 14.9 and 17.3 kcal/mole. From the ELS measurements we conclude a great sensitivity of H₂O for electron beam induced dissociation. At 273 K water adsorbs on Ni(110) only in the presence of oxygen, with two peaks at 5.7 and 9.3 eV below E_F (He(II)), being interpreted as due to hydroxyl species (OH)^δ? on the surface. A kinetic model for the H₂O adsorption on oxygen precovered Ni(110) surfaces is proposed, and verified by a simple Monte Carlo calculation leading to the same dependence of the maximum amount of adsorbed H₂O on the oxygen precoverage as revealed by work function measurements. On heating, some of the (OH)^δ? recombines and desorbs as H₂O at ? 320 K, leaving behind an oxygen covered Ni surface.     

The role of adsorbed sulfur in the H2D2 equilibration reaction on Pt single crystals

The H₂D₂ equilibration on Pt single crystals was investigated under intermediate pressure (100–400 Torr) and temperature (50–250°C), as a function of sulfur coverage. On Pt(110) and Pt(111), adsorbed sulfur modifies the kinetic parameters, activation energy and pre-exponential factor; the latter depends on the temperature on Pt(110) only. The clean Pt(110) face was found to be 5 times more active than the clean Pt(111). On both faces, adsorption of sulfur induces electronic effects on the neighbouring reactional sites. The difference in the behaviour of the two faces and a clear influence of the arrangement of the adsorbed sulfur atoms, deduced from LEED diagrams, tend to prove the structure dependency of the H₂D₂ reaction. A consistent reaction mechanism could be proposed, involving the dissociative adsorption and surface recombination of hydrogen and deuterium, and the reaction between adsorbed molecules for high sulfur coverages. The value of the sulfur coverage which makes the platinum inactive towards H₂D₂ is lower for the (111) than for the (110) orientation; this is in correlation with the roughness of the surface; the denser at atomic scale a surface is, the further is the extent of the lateral interactions due to adsorbed sulfur.     

A photoelectron spectroscopic investigation of the interaction between H2O and oxygen on Ag(110)

The adsorption and reaction of H₂O with adsorbed oxygen atoms on Ag(110) was examined by UPS. In agreement with previous EELS results, H₂O formed multilayers of ice upon adsorption at 140 K. The ice layers could be easily distinguished from monolayer coverages of chemisorbed H₂O (present above 160 K) by UPS. The ice layers produced (1) strong attenuation of the emission from the Ag d-bands, (2) a nearly 2 eV shift of H₂O valence levels to higher binding energy and (3) strong attenuation of emission from the H₂O 3a₁ orbital. H₂O was observed to react stoichiometrically with O(a) above 250 K to produce a pure layer of adsorbed hydroxyl species. The UPS spectra for these species exhibited features at ?5.8 and ?8.7 eV, as well as strong features above the d-bands. These spectra were compared with those for OH(a) on other surfaces, and the difficulties of identifying OH by UPS due to contamination by excess H₂O are discussed.     

The adsorption of CO,H2, H2, CO2 and H2O on carburized and graphitized Ni(110)

A study of the adsorption/desorption behavior of CO, H₂O, CO₂ and H₂ on Ni(110)(4 × 5)-C and Ni(110)-graphite was made in order to assess the importance of desorption as a rate-limiting step for the decomposition of formic acid and to identify available reaction channels for the decomposition. The carbide surface adsorbed CO and H₂O in amounts comparable to the clean surface, whereas this surface, unlike clean Ni(110), did not appreciably adsorb H₂. The binding energy of CO on the carbide was coverage sensitive, decreasing from 21 to 12 $\text{kcal}\text{mol}$ as the CO coverage approached 1.1 × 10¹⁵ molecules cm^?2 at 200K. The initial sticking probability and maximum coverage of CO on the carbide surface were close to that observed for clean Ni(110). The amount of H₂, CO, CO₂ and H₂O adsorbed on the graphitized surface was insignificant relative to the clean surface. The kinetics of adsorption/desorption of the states observed are discussed.     

The adsorption of SO2 on iron surfaces studied by x-ray photoelectron spectroscopy

The interaction of SO₂ with evaporated iron surfaces in the temperature range 80–450 K was investigated by using X-ray photoelectron spectroscopy. At 300 K, SO₂ decomposed at the initial stage of the interaction and gave adsorbed S with the S2p peak at 161.9 eV and adsorbed O with the O1s at 530.0 eV. Further exposure of SO₂ gave adsorbed SO₄ with S2p at 166.8 eV O1s at 531.3 eV, being different in binding energies from ionic SO₄^2?. This indicates the two stage reaction Of SO₂ with iron surface; SO₂(gas) → S(ads) + 20(ads), SO₂(gas) + 2O(ads) → SO₄(ads). The first reaction did not occur at low temperature or in the presence of adsorbed O. The adsorbed SO₄ formed at 80 K showed a quantitative decomposition reaction into S(ads) and O(ads) in the temperature range 200–350 K.     

C2H4在Ru(1010)表面吸附与分解的研究

用X射线电子能谱(XPS)、热脱附谱(TDS)和紫外光电子能谱(UPS)方法研究了乙烯(C_{2H4)在Ru(1010)表面的吸附,在低温下(200K以下)乙稀(C2Ｈ4})可以在Ru(1010)表面上以分子状态稳定吸附,在200K以上乙烯(C₂H ₄)则发生了脱氢分解反应.TDS结果表明乙烯(C₂H₄)分 解后的主要产物为乙炔(C< 关键词： 乙烯 钌(1010)表面 吸附与分解     

Adsorption and decomposition of H2O on a K-covered Pt(111) surface

The adsorption of H₂O on clean and K-covered Pt(111) was investigated by utilizing Auger, X-ray and ultra-violet photoemission spectroscopies. The adsorption on Pt(111) at 100–150 K was purely molecular (ice formation) in agreement with previous work. No dissociation of this adsorbed H₂O was noted on heating to higher temperatures. On the other hand, adsorption of H₂O on Pt(111) + K leads to dissociation and to the formation of OH species which were characterized by a work function increase, an O 1s binding energy of 530.9 eV and UPS peaks at 4.7 and 8.7 eV below the Fermi level. The amount of OH formed was proportional to the K coverage for θ_K > 0.06 whereas no OH could be detected for θ? 0.06. Dissociation of H₂O occurred already at T = 100 K, with a sequential appearance of O 1s peaks at 531 and 533 eV representing OH and adsorbed H₂O, respectively. At room temperature and above only the OH species was observed. Annealing of the surface covered with coadsorbed K/OH indicated the high stability of this OH species which could be detected spectroscopically up to 570 K. The adsorption energy of H₂O coadsorbed with K and OH on Pt(111) is increased relative to that of H₂O on Pt. The work function due to this adsorbed H₂O increases whereas it decreases for H₂O on Pt(111). The energy shifts of valence and O1s core levels of H₂O on Pt + K as deduced from a comparison of gas phase and adsorbate spectra are 2.8–4.2 eV compared to ≈ 1.3–2.3 eV for H₂O on Pt (111). This increased relaxation energy shift suggests a charge transfer screening process for H₂O on Pt + K possibly involving the unoccupied 4a₁ orbital of H₂O. The occurrence of this mode of screening would be consistent with the higher adsorption energy of H₂O on Pt + K and with its high propensity to dissociate into OH and H.     

Interaction of H2O with a clean and oxygen precovered Ni(110) surface studied by XPS

The adsorption and reaction of H₂O on clean and oxygen precovered Ni(110) surfaces was studied by XPS from 100 to 520 K. At low temperature (T<150 K), a multilayer adsorption of H₂O on the clean surface with nearly constant sticking coefficient was observed. The O 1s binding energy shifted with coverage from 533.5 to 534.4 eV. H₂O adsorption on an oxygen precovered Ni(110) surface in the temperature range from 150 to 300 K leads to an O 1s double peak with maxima at 531.0 and 532.6 eV for T=150 K (530.8 and 532.8 eV at 300 K), proposed to be due to hydrogen bonded O_ads… HOH species on the surface. For T>350 K, only one sharp peak at 530.0 eV binding energy was detected, due to a dissociation of H₂O into O_ads and H₂. The s-shaped O 1s intensity-exposure curves are discussed on the basis of an autocatalytic process with a temperature dependent precursor state.     

The adsorption and reaction of H2O on clean and oxygen covered Ag(110)

The adsorption and reaction of water on clean and oxygen covered Ag(110) surfaces has been studied with high resolution electron energy loss (EELS), temperature programmed desorption (TPD), and X-ray photoelectron (XPS) spectroscopy. Non-dissociative adsorption of water was observed on both surfaces at 100 K. The vibrational spectra of these adsorbates at 100 K compared favorably to infrared absorption spectra of ice Ih. Both surfaces exhibited a desorption state at 170 K representative of multilayer H₂O desorption. Desorption states due to hydrogen-bonded and non-hydrogen-bonded water molecules at 200 and 240 K, respectively, were observed from the surface predosed with oxygen. EEL spectra of the 240 K state showed features at 550 and 840 cm^?1 which were assigned to restricted rotations of the adsorbed molecule. The reaction of adsorbed H₂O with pre-adsorbed oxygen to produce adsorbed hydroxyl groups was observed by EELS in the temperature range 205 to 255 K. The adsorbed hydroxyl groups recombined at 320 K to yield both a TPD water peak at 320 K and adsorbed atomic oxygen. XPS results indicated that water reacted completely with adsorbed oxygen to form OH with no residual atomic oxygen. Solvation between hydrogen-bonded H₂O molecules and hydroxyl groups is proposed to account for the results of this work and earlier work showing complete isotopic exchange between H₂¹⁶O_(a) and ¹⁸O_(a).     

UPS and XPS studies of the chemisorption of O2, H2 AND H2O on reduced and stoichiometric SrTiO3(111) surfaces; The effects of illumination

About one monolayer of Ti³⁺ species is detectable at the surface of reduced SrTiO₃(111) single crystals by XPS and UPS. O₂, H₂ and H₂O have been adsorbed in the dark and the decrease on the concentration of the Ti³⁺ species has been monitored as a function of the gas exposures. Subsequent band gap illumination partially restores the Ti³⁺ initial concentration in the cases of O₂ and H₂ exposures but not in the case of H₂O. The Ti³⁺ photogeneration on the oxygen covered surface is associated with oxygen photodesorption as indicated by XPS and UPS. UPS measurements give evidence for surface hydroxylation resulting from water and hydrogen adsorption. The activity of the stoichiometric SrTiO₃(111) crystal face for O₂ and H₂ adsorption is very low when compared with the reduced SrTiO₃ samples.     

Site-specific interaction of H2O with ZnO single-crystal surfaces studied by thermal desorption and UV photoelectron spectroscopy

The adsorption and condensation of H₂O(D₂O) on ZnO(101&#x0304;0), (0001)Zn and (0001&#x0304;)O surfaces was investigated by means of thermal desorption (TDS) and UV photoelectron spectroscopy (UPS). The clean ZnO single-crystal surfaces were prepared by Ar-ion sputtering and annealing and characterised by Auger electron spectroscopy, LEED, UPS and work-function measurements. On all three surfaces six different adsorption states were found. In the monolayer regime there is a stronger bonding to Zn sites (desorption temperature 340 K) than to O sites (190 K), The bonding to the Zn sites seems to be accompanied by some clustering. Before the chemisorption layer is completed a first ice state is found whose desorption temperature shifts from 162 to 168 K with increasing exposures. At higher exposures the multilayer ice state is found at 152 K. On the (0001&#x0304;)O face defect-induced features were identified. The water lone-pair orbital 1b₁, whose energy falls between the O p and the Zn 3d emission of the substrate and which is known to show bonding shifts, was analysed using angle-resolved UPS. In the monolayer, the main chemisorption states are found at E_B^V(1b₁) = ?9.6 eV for the (0001)Zn face and at ? 10.6 eV for the (0001&#x0304;)O face and are compared with the multilayer ice emission at 1&#x0304;1.1 eV. The difference in binding energies shows the same trend as the TDS data. For the (101&#x0304;0) face the 1b₁ emission is very broad, indicating some overlap between different states.     

H2S在Fe(100)面吸附的第一性原理研究

基于密度泛函理论第一性原理, 在广义梯度近似下, 研究了表面覆盖度为0.25 ML (monolayer)时硫化氢分子在Fe(100)面吸附的结构和电子性质, 并与单个硫原子吸附结果进行了对比. 结果表明: 硫化氢分子吸附在B2位吸附能最小为-1.23 eV, 最稳定, B1位吸附能最大为-0.01 eV, 最不稳定; 并对硫化氢分子在B1位和B2位吸附后的电子态密度进行了分析, 也表明了吸附在B2位稳定, 且吸附在B2位后硫化氢分子几何结构变化不大; 将硫化氢中硫原子吸附与单个硫原子吸附的电子性质进行了比较, 发现前者吸附作用非常微弱; 同时对吸附后的Fe(100)面进行了对比, 单个硫原子吸附的Fe(100)面电子态密度出现了一系列峰值且离散分布, 生成了硫化亚铁, 表明在硫化氢环境下, 主要是硫化氢析出的硫原子发生了吸附. 关键词： 第一性原理 Fe(100)表面 吸附能 硫化氢     

The displacement of hydrogen by carbon monoxide on the (100) face of tungsten: A photoemission and thermal desorption study

Photoelectron spectra (hv = 21.22 eV) and thermal desorption data were obtained for CO and H coadsorbed on W(100) at 80 K. When the clean surface is exposed to a saturation dose of H₂, subsequent exposure to CO results in the formation of a state whose emission spectrum is similar to that of molecular α-CO. Upon heating to ~280 K, a structural rearrangement occurs in which most of the adsorbed CO is converted to the strongly bound β form as the hydrogen is simultaneously desorbed. These data plus the observation that H₂ cannot be adsorbed to any significant degree on a saturated layer of β-CO suggest that adsorbed β-CO and H occupy the same atomic sites on the W(100) surface. The distinction between long and short range repulsive COH interactions is discussed. For CO adsorbed on clean W(100), the range of activation energies for vigin to β conversion is calculated from the UPS data to be 45–62 kJ/mol.     

The adsorption of water on clean and oxygen covered Cu(110)

The water adsorption on clean and oxygen precovered Cu(110) surfaces is studied by means of UPS, LEED, work function measurements and ELS. At 90 K on the clean surface molecular water adsorption is indicated by UPS. The H₂O molecules are bonded at the oxygen end and the H-O-H angle is increased as compared with the free molecule. In the temperature range between 90 and 300 K distorted H₂O molecules and adsorbed hydroxyl species (OH) are detected, which are desorbed at room temperature. On an oxygen covered surface hydroxyl groups are formed by dissociation of adsorbed water molecules at a lower temperature than on the clean surface. Multilayers of condensed water are found below 140 K in both cases.     

Ion survival probabilities for 3 keV Ar+ scattering from La,Yb, and chemisorbed H2, O2, and H2O on La surfaces

TOF spectra of scattered primary and surface recoiled neutrals and ions for 3 keV Ar⁺ bombardment of clean La and Yb and H₂, O₂, and H₂O saturated La surfaces are presented. The spectra are analyzed in terms of single (SS) and multiple (MS) scattering of the primary ions and surface recoiling (SR) of adsorbate atoms. Measurement of spectra of neutrals + ions and neutrals alone allows determination of scattered ion fractions Y. The Y values for the SS event are high for clean La (37%) and lower for adsorbate covered La (32% for H₂, 13% for O₂, and 8% for H₂O); Yb exhibits a similar behavior, i.e. 16% for clean Yb and 5% for O₂ + H₂O covered Yb. Photon emission accompanying the scattering collision has been observed from clean La and Yb and adsorbate covered La. A preferential inelastic energy loss of 15 ± 3 eV for the SS event has been observed for scattered neutrals as opposed to ions for La and H₂ saturated La at 135°. These results are interpreted within the models for Auger and resonant electronic charge exchange transitions during approach or departure of an ion with a surface and the electron promotions occuring during close atomic encounters where the electron shells are interpenetrating.     

Interaction of O2, CO2, CO,C2H4 and C2H4O with Ag(110)

The interaction of O₂, CO₂, CO, C₂H₄ AND C₂H₄O with Ag(110) has been studied by low energy electron diffraction (LEED), temperature programmed desorption (TPD) and electron energy loss spectroscopy (EELS). For adsorbed oxygen the EELS and TPD signals are measured as a function of coverage (θ). Up to θ = 0.25 the EELS signal is proportional to coverage; above 0.25 evidence is found for dipole-dipole interaction as the EELS signal is no longer proportional to coverage. The TPD signal is not directly proportional to the oxygen coverage, which is explained by diffusion of part of the adsorbed oxygen into the bulk. Oxygen has been adsorbed both at pressures of less than 10^-4 Pa in an ultrahigh vacuum chamber and at pressures up to 10³ Pa in a preparation chamber. After desorption at 10³ Pa a new type of weakly bound subsurface oxygen is identified, which can be transferred to the surface by heating the crystal to 470 K. CO₂ is not adsorbed as such on clean silver at 300 K. However, it is adsorbed in the form of a carbonate ion if the surface is first exposed to oxygen. If the crystal is heated this complex decomposes into O_ad and CO₂ with an activation energy of 27 kcal/mol(1 kcal = 4.187 kJ). Up to an oxygen coverage of 0.25 one CO₂ molecule is adsorbed per two oxygen atoms on the surface. At higher oxygen coverages the amount of CO₂ adsorbed becomes smaller. CO readily reacts with O_ad at room temperature to form CO₂. This reaction has been used to measure the number of O atoms present on the surface at 300 K relative to the amount of CO₂ that is adsorbed at 300 K by the formation of a carbonate ion. Weakly bound subsurface oxygen does not react with CO at 300 K. Adsorption of C₂H₄O at 110 K is promoted by the presence of atomic oxygen. The activation energy for desorption of C₂H₄O from clean silver is ～ 9 kcal/mol, whereas on the oxygen-precovered surface two states are found with activation energies of 8.5 and 12.5 kcal/mol. The results are discussed in terms of the mechanism of ethylene epoxidation over unpromoted and unmoderated silver.     

H2 分子在Li3N(110)表面吸附的第一性原理研究

采用第一性原理方法研究了H₂分子在Li₃N(110)晶面的表面吸附. 通过研究H₂/Li₃N(110)体系的吸附位置、吸附能和电子结构发现: H₂分子吸附在N桥位要比吸附在其他位置稳定,此时在Li₃N(110)面形成两个-NH基,其吸附能为1.909 eV,属于强化学吸附;H₂与Li₃N(110)面的相互作用主要是H 1s轨道与N 关键词： 第一性原理 3N(110)')" href="#">Li₃N(110) 2')" href="#">H₂ 吸附和解离     

LEED and thermal desorption studies of small molecules (H2, O2, CO,CO2, NO,C2H4, C2H2 and C) chemisorbed on the stepped rhodium (755) and (331) surfaces

The chemisorption of H₂, O₂, CO, CO₂, NO, C₂H₂, C₂H₄ and C has been studied on the clean stepped Rh(755) and (331) surfaces. Low energy electron diffraction (LEED), Auger electron spectroscopy (AES) and thermal desorption spectroscopy (TDS) were used to determine the size and orientation of the unit cells, desorption temperatures and decomposition characteristics for each adsorbate. All of the molecules studied readily chemisorbed on both stepped surfaces and several ordered surface structures were observed. The LEED patterns seen on the (755) surface were due to the formation of surface structures on the (111) terraces, while on the (331) surface the step periodicity played an important role in the determination of the unit cells of the observed structures. When heated in O₂ or C₂H₄ the (331) surface was more stable than the (755) surface which readily formed (111) and (100) facets. In the CO and CO₂ TDS spectra a peak due to dissociated CO was observed on both surfaces. NO adsorption was dissociative at low exposures and associative at high exposures. C₂H₄ and C₂H₂ had similar adsorption and desorption properties and it is likely that the same adsorbed species was formed by both molecules.     

UPS spectra of H2O,CH3OH and C5H9OH adsorbed onto Cu(111)/Na and Na(cp)

The present communication presents ultraviolet photoemission spectra (UPS) of three different “alcohols”; water (H₂O), methanol (CH₃OH), and cyclopentanol (C₅H₉OH), chemisorbed onto a Cu(111) surface partially covered by sodium atoms as well as onto closely packed sodium films, a free electron adsorbent. Whereas all three alcohols ROH bind reversibly and associatively to Cu(111) they react with adsorbed sodium atoms to metal bound alcoxides RO. The chemisorption bond, characterized by the interaction between O 2pπ orbitals and metal atoms as an electron donor, the alcoxide being the acceptor, is similar for all groups R. The O 2pπ orbitals shift to higher UPS binding energies with increasing electron density, i.e. decreasing r_s/a_o of the sodium overlayer. Only for HONa, the sterically smallest group R, does the alcoxide growth continue in three dimensions. Although, possibly failing to reproduce the electron density profile of a free electron surface, Hartree-Fock-Slater cluster calculations of small models ROH and RONa₃ enable correlations to be made between UPS intensity peaks and one electron orbitals.     

A thermal desorption study of thiophene adsorbed on the clean and sulfided Mo(100) crystal face

The adsorption of thiophene (C₄H₄S) on the clean and sulfided Mo(100) crystal surface has been studied. A fraction of the adsorbed thiophene desorbs molecularly while the remainder decomposes upon heating, evolving H₂ and leaving carbon and sulfur deposits on the surface. The reversibly adsorbed thiophene exhibits three distinct desorption peaks at 360, 230–290 and 163–174 K, corresponding to binding energies of 22, 13–16 and 7–9 kcal/mol respectively. Sulfur on the Mo(100) surface preferentially blocks the highest energy binding state and causes an increase in the amount of thiophene bound in the low binding energy, multilayer state. The thiophene decomposition reactions yield H₂ desorption peaks in the temperature range 300–700 K. We estimate that 50–66% of the thiophene adsorbed to the clean Mo(100) decomposes. The decomposition reaction is blocked by the presence of c(2 × 2) islands of sulfur and is blocked completely at θ_s = 0.5, at which point thiophene adsorption is entirely reversible.