The effect of sulfur on co adsorption/desorption on Pt(S)-[9(111) × (100)]

CO adsorption/desorption on clean and sulfur covered Pt(S)-[9(111) × (100)] surfaces was studied using AES, TPD, and modulated beam experiments. CO desorption occurred from two states on the clean surface — a low temperature state associated with the (111) terraces and a high temperature state associated with the steps/defects. Thermal desorption results indicated that above small CO coverages conversion from the low temperature state into the high temperature state was activated and that back conversion was slow. Sulfur preferentially adsorbed at step/defect sites and decreased the population of the high temperature desorption state. Modulated beam experiments were performed in order to determine CO adsorption/desorption parameters as a function of sulfur coverage on the Pt crystal. The sticking coefficient and binding energy of CO decreased as the sulfur concentration increased. Sulfur adsorption at step/defect sites decreased the CO sticking coefficient only slightly but increased the effective rate constant for CO desorption significantly. Sulfur adsorption on the terraces affected CO adosrption more than sulfur at step sites. On the clean surface the effective rate constant for CO desorption was

$\text{1 × 10}{}^{15}\text{s}{}^{\mathrm{?1}}\text{exp (}\text{?36.2 kcal/mole}\text{RT}\text{)}$

Desorption occurred from both terrace and step/defect sites, but the kinetics were characteristic of the step/defect sites. For the surface on which step/defect sites were blocked by sulfur the effective desorption rate constant was

$\text{k}{}_{\mathrm{eff}}\text{= 1 × 10}{}^{13}\text{s}{}^{\mathrm{?1}}\text{exp (?}\text{27.5 kcal/mole}\text{RT}\text{)}$

indicating an appreciable decrease in CO binding on the terraces, though sulfur-CO repulsive interactions had probably made k_eff larger than the true rate constant for desorption from clean (111) planes. The results showed clearly a compensation effect in activation energy and preexponential factor.     

The adsorption of CO,H2, H2, CO2 and H2O on carburized and graphitized Ni(110)

A study of the adsorption/desorption behavior of CO, H₂O, CO₂ and H₂ on Ni(110)(4 × 5)-C and Ni(110)-graphite was made in order to assess the importance of desorption as a rate-limiting step for the decomposition of formic acid and to identify available reaction channels for the decomposition. The carbide surface adsorbed CO and H₂O in amounts comparable to the clean surface, whereas this surface, unlike clean Ni(110), did not appreciably adsorb H₂. The binding energy of CO on the carbide was coverage sensitive, decreasing from 21 to 12 $\text{kcal}\text{mol}$ as the CO coverage approached 1.1 × 10¹⁵ molecules cm^?2 at 200K. The initial sticking probability and maximum coverage of CO on the carbide surface were close to that observed for clean Ni(110). The amount of H₂, CO, CO₂ and H₂O adsorbed on the graphitized surface was insignificant relative to the clean surface. The kinetics of adsorption/desorption of the states observed are discussed.     

Chemisorption studies on cobalt single crystal surfaces: I. Carbon monoxide on Co(0001)

The chemisorption of CO on Co(0001) and on a polycrystalline specimen has been studied by LEED, Auger spectroscopy, and thermal desorption measurements. Annealing of the polycrystal was found to result in a surface dominated by crystallites of (0001) orientation in the surface plane, along with a few (101̄2) oriented crystallites. CO adsorbs on the clean surface at 300 K with an initial sticking probability of 0.9 and the system follows precursor state kinetics. The saturation coverage under UHV conditions corresponds to a well-ordered (√3 × √3)R30° structure; with P_CO>5 × 10^-9 a uniform compression of the adlayer takes place and a (√7 × √7)R19.2° structure begins to form. Models are proposed for these two ordered phases which are in agreement with the observed relative coverage data and the appearance of the corresponding desorption spectra. The desorption enthalpy of CO at low coverages is 103 ± 8 kJmol^-1, and a fairly sharp fall in this enthalpy occurs for coverages $\text{>}\text{1}\text{3}$. In many respects, the system's behaviour closely resembles that of Ni(111)-CO. Oxygen contamination leads to the appearance of a strongly adsorbed CO state with a desorption enthalpy of ~170 kJmol^-1. This is reminiscent of a strongly adsorbed non-dissociated state of CO on Ru(101̄1) which occurs under similar conditions.     

The binding energy of CO on clean and sulfur covered platinum surfaces

The desorption of CO from clean Pt(111) and (100), and from the same surfaces with partial overlayers of sulfur, was studied by Thermal Desorption Spectroscopy. The method of desorption rate isotherms was employed for data analysis. The desorption of CO from the (111) surface and both surfaces with ordered sulfur overlayers can be described as a first order process with coverage dependent activation energies. The desorption of CO from the clean Pt(100) surface is complicated by the dynamic interaction of the molecule with a thermally activated change of platinum surface structure. On both platinum faces surface sulfur decreases the initial binding energy of CO. As the CO concentration increases, its binding energy decreases very rapidly. This is due to a repulsive interaction which exists between co-adsorbed species.     

Adsorption of sodium and its effect upon some electric properties of clean germanium (111) surfaces

The effect of adsorbed Na on the surface conductivity, Δσ, and surface recombination velocity, S, of a clean (114)Ge surface is studied. The surface conductivity is a complicated function of the surface Na concentration, N_Na; at N_Na ≈ 1.5 × 10¹³ atoms/cm², it has a minimum; at ca. (3–5) × 10¹⁴atoms/cm², it has a maximum. For a monolayer coverage (ca. 7.2 × 10¹⁴atoms/cm²) the values of Δσ are not much different from those of a clean Ge surface. The surface recombination velocity is a three-valued function of the surface potential, U_S (calculated from the Δσ values), depending on the Na overlayer coverage and heat treatment of the sample. Three different surface structures (LEED data) were found to correspond to the three S versus U_S curves reported here. Thermal desorption studies show that Na is desorbed in a wide temperature interval. Two peaks have been isolated, studied and discussed. At low coverages a single peak is found to exist, which obeys the first-order desorption kinetics, with a desorption energy of (52 ± 3)kcal/mol. This peak is attributed to the surface defects. For coverages close to$\text{1}\text{4}$ monolayer a new peak was observed in the spectrum. The desorption energy of this binding state exceeds that of all the other states. When the overlayer coverage is increased, this peak is shifted to higher temperatures, as predicted for a half-order desorption kinetics. By comparing also with LEED data, it may be concluded that this most tightly bound sodium has formed on the Ge(111) surface patches of an ordered structure in which one Na atom is bonded to three Ge atoms.     

A molecular beam study of the adsorption dynamics of CO on Ru(0001), Cu(111) and a pseudomorphic Cu monolayer on Ru(0001)

We have investigated the sticking coefficient of CO on Ru(0001), a pseudomorphic Cu monolayer on Ru(0001), and a fully relaxed Cu(111) multilayer as function of kinetic energy, surface coverage, and surface temperature. At a low kinetic energy of 0.09 eV, the initial sticking coefficients, S₀, on these surfaces are determined to be 0.92, 0.96 and 0.87, respectively. In all cases, a decrease of S₀ with increasing beam energy was observed, yielding values of 0.58, 0.14 and 0.07, respectively, at a kinetic energy of 2.0 eV. For all three surfaces the coverage dependent sticking coefficients, S(Θ), display very characteristic behavior at low kinetic energies: S(Θ) remains more or less constant up to coverages close to saturation, indicative of precursor adsorption kinetics. However, characteristic minima at intermediate coverages are observed, which are correlated to the formation of well ordered adsorbate phases. For high kinetic energies we observe a transition towards a linear decrease of S(Θ) for Ru(0001). In contrast, for the pseudomorphic Cu monolayer and for Cu(111) we find an increase in the sticking coefficients at low coverages, followed by a decrease close to saturation. This behavior is attributed to adsorbate assisted sticking, that is, to a higher sticking coefficient on adsorbate covered regions than on the bare surface. The comparison between the pseudomorphic monolayer and Cu(111) reveals that the CO bond strength to the former is larger by 40%. The initial sticking coefficients for both surfaces are very similar at low kinetic energies; at high kinetic energies, S₀ for the pseudomorphic Cu monolayer is, however, larger by a factor of two.     

Characterization of oxygen,carbon, and sulfur adlayers on W(211)

Adlayers of oxygen, carbon, and sulfur on W(211) have been characterized by LEED, AES, TPD, and CO adsorption. Oxygen initially adsorbs on the W(211) surface forming p(2 × 1)O and p(1 × 1)O structures. Atomic oxygen is the only desorption product from these surfaces. This initial adsorption selectively inhibits CO dissociation in the CO(β₁) state. Increased oxidation leads to a p(1 × 1)O structure which totally inhibits CO dissociation. Volatile metal oxides desorb from the p(1 × 1)O surface at 1850 K. Oxidation of W(211) at 1200 K leads to reconstruction of the surface and formation of p(1 × n)O LEED patterns, 3 ? n ? 7. The reconstructed surface also inhibits CO dissociation and volatile metal oxides are observed to desorb at 1700 K, as well as at 1850 K. Carburization of the W(211) surface below 1000 K produced no ordered structures. Above 1000 K carburization produces a c(6 × 4)C which is suggested to result from a hexagonal tungsten carbide overlayer. CO dissociation is inhibited on the W(211)?c(6×4)C surface. Sulfur initially orders into a c(2 × 2)S structure on W(211). Increased coverage leads to a c(2×6)S structure and then a complex structure. Adsorbed sulfur reduces CO dissociation on W(211), but even at the highest sulfur coverages CO dissociation was observed. Sulfur was found to desorb as atomic S at 1850 K for sulfur coverages less than $\text{7}\text{6}$ monolayers. At higher sulfur coverages the dimer, S₂, was observed to desorb at 1700 K in addition to atomic sulfur desorption.     

Adsorption and reaction of nitric oxide and oxygen on Rh(111)

Adsorption of NO and O₂ on Rh(111) has been studied by TPD and XPS. Both gases adsorb molecularly at 120 K. At low coverages (θ_NO < 0.3) NO dissociates completely upon heating to form N₂ and O₂ which have peak desorption temperatures at 710 and 1310 K., respectively. At higher NO coverages NO desorbs at 455 K and a new N₂ state obeying first order kinetics appears at 470 K. At saturation, 55% of the adsorbed NO decomposes. Preadsorbed oxygen inhibits NO decomposition and produces new N₂ and NO desorption states, both at 400 K. The saturation coverage of NO on Rh(111) is approximately 0.67 of the surface atom density. Oxygen on Rh(111) has two strongly bound states with peak temperatures of 840 and 1125 K with a saturation coverage ratio of 1:2. Desorption parameters for the 1125 peak vary strongly with coverage and, assuming second-order kinetics, yield an activation energy of $\text{85 ± 5}\text{kcal}\text{mol}$ and a pre-exponential factor of 2.0 cm² s^?1 in the limit of zero coverage. A molecular state desorbing at 150 K and the 840 K state fill concurrently. The saturation coverage of atomic oxygen on Rh(111) is approximately 0.83 times the surface atom density. The behavior of NO on Rh and Pt low index planes is compared.     

Low temperature ordering of sodium overlayers on RU(001)

The adsorption of alkali metals on transition metals can produce several technologically important effects, but only limited results have been reported on the geometrical structure of such adlayers, especially for adsorption temperatures below 300 K. We have examined the adsorption of Na on Ru(001) as a function of coverage and temperature using LEED to determine the adlayer structure and thermal desorption spectroscopy to characterize binding kinetics and relative Na coverages. The only Na LEED pattern observed following adsorption at 300 K was that of $\text{(}\text{3}\text{2}\text{×}\text{3}\text{2}\text{)}$ structure which occurred near saturation of the first layer. However, Na adsorbed at 80 K produces a progression of distinct, ordered LEED patterns with increasing coverage which does not include the $\text{(}\text{3}\text{2}\text{×}\text{3}\text{2}\text{)}$ pattern. These patterns result from increasingly compressed, hexagonal arrangements of adsorbate atoms which are uniformly spaced due to mutually repulsive interactions. The order-disorder transition temperature for each structure was also determined by LEED and used to develop a 2D phase diagram for Na on Ru(001). Ordered structures were observed only when Na thermally induced motion was sufficiently limited and the repulsive Na-Na interaction could force the uniform spacing of Na atoms. Thus, low coverage structures only developed where Na mobility was limited by low temperature. High coverage structures were stable to much higher temperatures since motion was inhibited by the high Na density.     

The influence of potassium and the role of coadsorbed oxygen on the chemisorptive properties of Pt(100)

The adsorption of K on Pt(100) has been followed by thermal desorption spectroscopy (TDS) and Auger electron spectroscopy (AES); carbon monoxide was used as a probe for the modification of the chemical properties of K promoted surfaces. The role of subsequent adsorption of oxygen on the K modified surfaces has also been measured. For low potassium coverage (θ_K = 0 to 0.35), the mass-28 TDS peak temperature of adsorbed CO increases continuously with the K coverage, indicating an increase of the adsorption energy of CO which has been explained by a substantial charge donation from K into the $\text{2π}{}^1$ orbitals of CO via long range interactions through the platinum substrate. No oxygen uptake was detected after oxygen exposure at room temperature. For high potassium content (θ_K = 0.45 to 1), the mass-28 TDS peak temperature of coadsorbed CO is very narrow and remains constant at 680 K. We propose the formation of a COKPt surface complex which decomposes at 680 K, since K desorption is detected concomitantly to CO. On such K covered surfaces, the oxygen uptake is promoted, and it cancels the modifications of the surface properties induced by potassium.     

Anomalous preexponential factor for hydrogen desorption from platinum single crystals?

Abnormally low values found by some authors for the preexponential for hydrogen desorption from platinum surfaces have recently been explained by an adsorbate induced change in the dynamical characteristics of the surface itself. This possibility has been investigated in the present work exploiting the Debye-Waller effect in He beam diffraction from a hydrogen covered Pt(997) surface. Essentially no dependence of adsorbate induced attenuation of the diffracted beam intensities on the primary He-beam energy has been observed. Therefore no indications have been found for changes in the perpendicular component of platinum surface vibrations due to adsorbed hydrogen. Likewise, heats of adsorption, obtained from He diffraction experiments, do not depend on the primary energy of the He beam. This result supports the obtained normal value for the preexponential factor of $\text{ca. 10}{}^{\mathrm{?2}}\text{cm}{}^2\text{atom · s}$ (Poelsema et al., Surface Sci. 111 (1981) 519).     

The properties of K and coadsorbed CO + K on Ru(001): I. Adsorption,desorption, and structure

An extensive photoemission and LEED study of K and CO+K on Ru(001) has been carried out. In this paper the LEED and some XPS results together with TPD and HREELS data are presented in terms of adsorption, desorption. and structural properties, and their compatibility is discussed. Potassium forms (2 × 2) and $\text{(}\text{3}\text{×}\text{3}\text{)R30°}$ overlayers below and near monolayer coverage, and multilayer bonding and desorption is similar to that of bulk K. The initial sticking coefficients for CO adsorption on K predosed surfaces are correlated with the initial K structure, and s₀ and CO saturation coverages decrease with increasing K coverage. Two well-characterized mixed CO+K layers have been found which are correlated with predosed (2 × 2) K and $\text{(}\text{3}\text{×}\text{3}\text{)R30°}\text{K}$. They have CO to K ratios of 3:2 and 1:1, and lead to LEED patterns with (2 × 2) and (3 × 3) symmetry, respectively. The molecule is believed to be sp² rehybridized under the influence of coadsorbed K, leading to stronger CO-Ru and weaker C-O bonds as indicated by the TPD and HREELS results, and to stand upright in essentially twofold bridges.     

binding states of CO and H2 on clean and oxidized (111)Pt

The binding states and sticking coefficients of CO and H₂ on clean and oxide covered (111)Pt are examined using flash desorption mass spectrometry and Auger electron spectroscopy (AES). On the clean surface at 78 K there is one major binding state of CO with a desorption activation energy which decreases with coverage plus a second smaller state, while H₂ exhibits three binding states with peak temperatures of 140, 230 and 310 K and saturation density ratios of 0.5 : 1 : 1. Desorption kinetics of CO are consistent with a first order state with a normal pre-exponential factor of 10^{13 ± 1} sec^?1, while all three peaks of H₂ are broader than expected. Interpretations in terms of anomalous pre-exponential factors, coverage dependent desorption activation energies, and desorption orders are considered. On the oxidized surface saturation densities of both gases are nearly identical to those on the clean surface, but desorption temperatures are increased significantly and the initial sticking coefficient on the oxide decreases slightly for CO and increases slightly for H₂.     

Chemisorption-induced Pt 4f surface core level shifts

Soft X-ray photoemission experiments have led to the unambiguous observation of a metal surface core level ($\text{Pt}\text{4}\text{f}{}_{\mathrm{<mtext>7</mtext><mtext>2</mtext>}}$) shift, due to an adsorbate (CO), to a binding energy larger than the bulk binding energy. The $\text{4}\text{f}{}_{\mathrm{<mtext>7</mtext><mtext>2</mtext>}}$ clean (110) surface component, with a binding energy 0.35 ± 0.02 eV lower than the bulk, is shifted by 1.06 ± 0.04 eV towards higher binding energy upon CO chemisorption. The lack of significant changes in the bulk component indicates the localized nature of the CO-Pt surface bonding.     

Oxygen chemisorption and the carbon monoxide-oxygen interaction on Ru(101)

The adsorption of oxygen and the interaction of carbon monoxide with oxygen on Ru(101) have been studied by LEED, Auger spectroscopy and thermal desorption. Oxygen chemisorbs at 300 K via a precursor state and with an initial sticking probability of ~0.004, the enthalpy of adsorption being ~300 kJ mol^?1. As coverage increases a well ordered ¦11,30¦ phase is formed which at higher coverages undergoes compression along [010] to form a ¦21,50¦ structure, and the surface eventually saturates at 0 ~ $\text{8}\text{9}$. Incorporation of oxygen into the subsurface region of the crystal leads to drastic changes in the surface chemistry of CO. A new high; temperature peak (γ CO, E_d ~ 800 kJ mol^?1) appears in the desorption spectra, in addition to the α and β CO peaks which are characteristic of the clean surface. Coadsorption experiments using ¹⁸O₂ indicate that γ CO is not dissociatively adsorbed, and this species is also shown to be in competition with β CO for a common adsorption site. The unusual temperature dependence of the LEED intensities of the ¦11,30¦-O phase and the nature of α, β, and β CO are discussed. Oxygen does not displace adsorbed CO at 300 K and the converse is also true, neither do any Eley-Rideal or Langmuir-Hinshelwood reactions occur under these conditions. Such processes do occur at higher temperatures, and in particular the reaction CO(g) + O(a) → CO₂(g) appears to occur with much greater collisional efficiency than on Ru(001). The oxidation of CO has been examined under steady state conditions, and the reaction was found to proceed with an apparent activation energy of 39 kJ mol^?. This result rules out the commonly accepted explanation that CO desorption is rate determining, and is compared with the findings of other authors.     

Distinct binding states in adsorption on a homogeneous surface: Te on W(100)

The adsorption of Te on a W(100) surface is studied by thermal desorption spectroscopy (TDS), Auger electron spectroscopy (AES), low energy electron diffraction (LEED) and work function change (Δ?) measurements. Three distinct binding states are observed in the first monolayer corresponding the coverages from 0 to $\text{1}\text{2}$ monolayers (ML), $\text{1}\text{2}$ to $\text{2}\text{3}$ ML and$\text{2}\text{3}$ to 1 ML. Within each state a coverage dependence of the desorption parameters is found. The three binding states are discussed in terms of heterogeneity induced by lateral interactions and in terms of inherently different adsorption sites.     

Evaluation of flash desorption spectra

It is shown that desorption energies may be extracted from thermal desorption spectra without any assumption on the preexponential, ν, regardless of coverage. This allows a determination of ν, at least at low coverages. Experimental TD spectra of CO adsorbed at $\text{Co(10}\text{1}\text{0)}$ are evaluated to illustrate the applicability of the procedure.     

The interaction of oxygen with the Rh(111) surface a

The adsorption of oxygen on Rh(111) at 100 K has been studied by TDS, AES, and LEED. Oxygen adsorbs in a disordered state at 100 K and orders irreversibly into an apparent (2 × 2) surface structure upon heating to T? 150 K. The kinetics of this ordering process have been measured by monitoring the intensity of the oxygen $\text{(1,}\text{1}\text{2}\text{) LEED}$ beam as a function of time with a Faraday cup collector. The kinetic data fit a model in which the rate of ordering of oxygen atoms is proportional to the square of the concentration of disordered species due to the nature of adparticle interactions in building up an island structure. The activation energy for ordering is $\text{13.5 ± 0.5}\text{kcal}\text{mole}$. At higher temperatures, the oxygen undergoes a two-step irreversible disordering (T? 280 K) and dissolution (T?400K) process. Formation of the high temperature disordered state is impeded at high oxygen coverages. Analysis of the oxygen thermal desorption data, assuming second order desorption kinetics, yields values of 56 ± 2 kcal/ mole and 2.5 ± 10^?3 cm² s^?1 for the activation energy of desorption and the pre-exponential factor of the desorption rate coefficient, respectively, in the limit of zero coverage. At non-zero coverages the desorption data are complicated by contributions from multiple states. A value for the initial sticking probability of 0.2 was determined from Auger data at 100 K applying a mobile precursor model of adsorption.     

Adsorption of ethylene on the Pt(100) surface

Clean Pt(100) surfaces with bulk-like 1×1 structure, or the stable, reconstructed 5×20 structure and held at 200 or 330 K were exposed to ethylene. Ultraviolet photoemission spectroscopy identified the nature of the adsorbed species which depends on the structure and temperature of the clean surface and the amount adsorbed. It is ethylene on the 5 × 20 structure at 200 K, a vinyl radical on the same surface at 300 K up to half a monolayer, the remainder being added as acetylene; it is acetylene on the 1 × 1 surface at 330 K and a mixture of acetylene, vinyl and ethylene on the 1 × 1 surface at 200 K. Whatever the nature of the adsorbate, the surface coverage θ increased with exposure ? as $\text{(1 ? θ = C?}{}^{\mathrm{<mtext>?</mtext><mtext>1</mtext><mtext>3</mtext>}}\text{)}$. By contrast, on a surface covered with any C₂ hydrocarbon acetylene adsorbs with Langmuir kinetics. The kinetics are explained in terms of the relationship between the attraction an approaching molecule experiences from the bare surface and its Van der Waals repulsion from preadsorbed molecules.