锌在金电极上的欠电位沉积

采用循环伏安法和计时电流法,研究了强碱溶液中锌在金电极上的欠电位沉积。 通过改变锌离子浓度和扫描速率等实验参数,在约-0.935 V（vs.SCE）开始出现锌的欠电位沉积,并且金属离子浓度的变化可能会影响到欠电位沉积过程的动力学机制;计时电流实验证实,锌欠电位沉积于金衬底上遵循的是受掺入吸附原子控制的二维瞬时成核和生长机制;且OH-离子的吸附对锌欠电位沉积具有重要的影响。     

甲醇在欠电位沉积Ru修饰Pt电极上的催化氧化

采用欠电位沉积(upd)方法在Pt 表面沉积亚单层的Ru制备出upd-Ru/Pt 电极. 通过欠电位沉积前后电极在0.5 mol·L-1 H2SO4溶液中循环伏安图-152 - 128 mV(vs Ag/AgCl)电位范围内对氢区的数值积分确定Pt表面Ru 的覆盖度. 用电化学方法测试了甲醇在upd-Ru/Pt电极上的催化氧化, 并讨论分析了欠电位沉积电位和Ru的表面覆盖度对甲醇氧化的影响. 结果表明, Ru能够欠电位沉积到Pt表面. Pt表面欠电位沉积少量的Ru 即能大大促进甲醇的氧化.只要控制upd-Ru的沉积量, upd-Ru原子就能大大促进甲醇氧化而与沉积电位无关. Ru原子对甲醇氧化的促进作用与Ru和Pt是否形成合金无关, 而取决于Ru 在Pt表面的百分含量.     

Sb在Cu单晶电极上欠电位沉积的电化学和现场STM研究

应用循环伏安法和现场扫描隧道显微镜研究了在HClO4和H2SO4两种溶液中Sb于Cu(111)和Cu(100)电极上的欠电位沉积.结果表明,不同的表面原子排列和强吸附阴离子的存在将明显影响Sb的欠电位沉积行为.在结构较为开放的Cu(100)表面,Sb形成的欠电位沉积层结构也较为开放,并且伴随着表面合金的形成;而在密堆积的Cu(111)表面上,Sb形成了致密的单层结构.又当Cu(111)表面存在强吸附的SO42-时,Sb原子首先在SO42-吸附层与Cu表面交接的新台阶处成核,随后通过取代SO42-向上一层晶面发展,表现出独特的成核—生长行为;而在弱吸附的HClO4溶液中,Sb的欠电位沉积系以在晶面上随机形成一些单原子层高度的Sb岛为特征.在Cu(100)表面,通过SO42-的诱导共吸附,欠电位沉积的Sb原子形成了开放性更大的(4×4)结构,不同于在HClO4溶液中所形成的(22×22)R45°结构.     

铅于旋转银盘电极上欠电位沉积的计时库仑法研究

用计时库仑法研究了Ｐｂ２＋于旋转Ａｇ盘电极（Ａｇ－ＲＤＥ）上的欠电位沉积（ＵＰＤ）性质。实验证明,支持电解质（０．０１ｍｏｌ／Ｌ　ＨＮＯ３＋０．０１　ｍｏｌ／Ｌ ＮａＣＩ）中Ｃｌ－离子的存在有利于取得稳态条件下ＵＰＤ Ｐｂ的电量值。其氧化过程电量（Ｑａ）,代表Ｐｂ２＋吸附单层被定量转化为ＵＰＤ Ｐｂ单层的量,Ｑａ的平均值为３９３．３μＣ／ｃｍ２,相应于２×１０－９ｍｏｌ／ｃｍ２Ｐｂ２＋表面复盖量。     

修饰铂电极上Mn(Ⅱ)的示波双电位滴定法测定

制备了Mn(Ⅱ)修饰铂电极,用循环伏安法表征了修饰电极的电化学性能,并对电极响应机理进行了探讨.优化了试验条件,提出了一种新的测定Mn(Ⅱ)的示波双电位滴定法.在1.0 mol/L的六次甲基四胺底液(pH=5.5～6.6)中,用修饰电极作为双指示电极,以EDTA标准溶液滴定Mn(Ⅱ),利用示波器屏幕上荧光点的显著最大位...     

修饰铂电极上Zn(Ⅱ)的示波双电位滴定法

制备了锌修饰铂电极,建立了一种新的测定Zn(Ⅱ)的示波双电位滴定法。在1.0 mol/L的六次甲基四胺溶液中(pH=5.5),用制备的修饰铂电极作为双指示电极,以EDTA标准溶液滴定Zn (Ⅱ),利用示波器屏幕上荧光点的显著最大位移指示滴定终点。Zn (Ⅱ)在3.0×10-4 ～2.0×10-3 mol/L时,回收率为99.9%～100.2%。该修饰电极具有良好的稳定性和重现性,在含有1.0×10-3 mol/L Zn (Ⅱ)的溶液中,连续11次测定,所得终点电位值均在10.1 mV左右,其相对标准偏差(RSD)0.5%。应用该方法测定含锌样品,测定结果与指示剂法测定值相符。     

修饰铂电极上Bi(Ш)的示波双电位滴定法

制备了Bi(Ⅲ)修饰铂电极,用循环伏安法表征了Bi(Ⅲ)在电极上的吸附特性,探讨了电极的响应机理。 通过优化实验条件,建立了一种测定Bi(Ⅲ)的示波双电位滴定法。 在0.1 mol/L的硝酸溶液中(pH=1.0),用制备的修饰铂电极作为双指示电极,以EDTA标准溶液滴定Bi(Ⅲ),利用示波器屏幕上荧光点的显著最大位移指示滴定终点。 Bi(Ⅲ)在1.19×10-4～1.44×10-2 mol/L时,回收率为99.8%～100.1%,检出限(S/N=3)为1.0×10-4 mol/L。 该修饰电极具有良好的稳定性和重现性,在含有1.0×10-2 mol/L Bi(Ⅲ)的溶液中,连续7次测定,所得终点电位值均在100 mV左右,其相对标准偏差(RSD)为0.04%。 应用该方法测定含铋样品,RSD值(n=7)小于0.25%,回收率为99.5%～100.5%,测定结果与指示剂法测定值相符。     

修饰铂电极上Cd(Ⅱ)的示波双电位滴定法

制备了镉修饰铂电极, 用循环伏安法表征了Cd(Ⅱ)在该电极上的吸附特性, 探讨了电极的响应机理. 通过优化试验条件, 建立了一种新的测定Cd(Ⅱ)的示波双电位滴定法. 在1.0 mol/L 的六次甲基四胺溶液中(pH＝6.0), 用制备的修饰铂电极作为双指示电极, 以EDTA 标准溶液滴定Cd(Ⅱ), 利用示波器屏幕上荧光点的显著最大位移指示滴定终点.Cd(Ⅱ)在9.0×10^－4～3.5×10^－3 mol/L 时, 回收率为99.8%～100.3%. 该修饰电极具有良好的稳定性和重现性, 在含有1.0×10^－3 mol/L Cd(Ⅱ)的溶液中, 连续13 次测定, 所得终点电位值均在37 mV左右, 其相对标准偏差(RSD)0.02%. 应用该方法测定含镉样品, RSD 值(n＝7)小于0.81%, 回收率为99.71%～100.09%, 测定结果与指示剂法测定值相符.     

甲醇在欠电位沉积Sn/Pt电极上催化氧化

在欠电位沉积（upd）锡修饰的铂电极（upd-Sn/Pt）上,对甲醇电化学催化氧化过程进行了研究.发现当Pt表面upd-Sn的覆盖率在20％附近时,对甲醇的催化氧化的增强作用最为明显；在电位低于0.35 V （vs RHE）时,甲醇在Pt与upd-Sn/Pt电极上氧化只进行到脱氢生成CO的步骤;在0.35 V以后,表面Sn－OH形成,反应Sn－OH＋COads=Sn＋CO2＋H＋＋e有利于表面CO的去除;而Pt电极上,只有0.6 V以后,才有反应Pt－OH＋COads=Pt＋CO2＋H＋＋e发生.因此,Sn的存在有利于甲醇在较低的电位下氧化; Pt电极上CH3OH脱氢并释放出电子的过程是一个快速的过程,表面CO的去除是甲醇氧化过程的控制步骤;甲醇氧化产生的表面吸附态CO 以线式吸附为主,少量的桥式吸附态CO在反应初期即达到吸附饱和; Pt表面上upd-Sn表现的催化增强作用,在光亮铂电极和在高分散铂黑电极上是一致的.     

Pt(S)[n(100)×(110)]表面Cu欠电位沉积(英文)

本文研究了Cu在Pt(100)台阶面和(110)单原子台阶的欠电位沉积.发现若不考虑阴离子吸附,初始阶段Cu在台阶面和台阶处的电沉积同时进行.在电沉积满单层的伏安曲线上,可以观察到若干峰.通过对峰电荷与台阶密度关系的分析,可认为这些峰分别对应于不同的沉积位点.较正电位的峰对应于Cu在台阶面上的电沉积,而在台阶处Cu的电沉积则因溶液中的阴离子而具有不同的伏安性质.此外,还发现Pt电极表面的Cu沉积电荷转移数接近2e,且沉积初始阶段阴离子覆盖度不变.     

Spectrophotometry Determination of Arsenic(III) and Antimony(III) by Means of Isonicotinoylhydrazones of 4-Dimethylaminobezaldehyde (4-Dbih) and 2-Hydroxynaphthaldehyde (2-Hnih)

Abstract

4-DBIH and 2-HNIH react with As(III) and Sb(III) respectively, in CH₃COOH medium to form colored complexes stable in presence of EDTA. As(III) and Sb(III) do not react with 2-HNIH and 4-DBIH respectively, and the Sb(III)-2-HNIH complex is extractable into isoamyl alcohol. These behaviours were used for the spectrophotometry determination of As (III) and Sb(III) in presence of several cations.     

Underpotential Deposition and Stripping of Lead at Disorganized Monolayer‐Modified Gold Electrodes

Underpotential deposition (UPD) and stripping of Pb²⁺ at thiol‐based disorganized monolayer‐modified gold electrodes was studied by cyclic voltammetry (CV) and electrochemical quartz crystal microgravimetry (EQCM). Electrodes modified with mercaptoacetic acid or mercaptoethane sulfonic acid were studied. Due to the proximity of the potentials for the Pb UPD and thiol reductive desorption, achievement of a UPD‐stripping voltammetry methodology for determination of low concentrations of Pb²⁺ was not successful. However by comparison of the CV and EQCM data and consideration of the possible mass changes per mole electrons transferred in light of the other species present in solution, possible mechanisms are put forward for the deposition and stripping of Pb²⁺ at thiol‐modified electrodes.     

一种金属单晶电极制备方法的建立和Cu2+在铂单晶上UPD过程的研究

同种材料而表面结构不同的电极往往有完全不同的电化学性能.使用在原子水平上表面结构明确的单晶电极不仅有助于对电极表面吸脱附过程、电场作用下表面结构重组、双电层微观结构、分子水平上的反应机理等基础理论进行深入研究,且对高选择性、高效电催化剂的研制也有指导意义.单晶电化学研究的基础就是制备定向不同的单晶电极.本文建立了金属单晶电极制备方法,并报道了Cu²⁺在Pt单晶电极上UPD(欠电位沉积)过程的研究结果.     

Underpotential deposition of tin(II) on a gold disc electrode and determination of tin in a tin plate sample

This work describes a study of the underpotential deposition (UPD) of Sn²⁺ on a polycrystalline gold disc electrode using cyclic voltammetry (CV) and chronocoulometry (CC). Sn²⁺ ions showed well-defined peaks from UPD and UPD stripping (UPD-S) in 1 mol/L HCl solutions, while bulk deposition (BD) and BD stripping (BD-S) of the ions were also observed. The measured UPD shifts, E_UPD, between the UPD-S and the BD-S peaks were more than 200 mV. The UPD charge and the surface coverage of tin were measured by CC. A new method for determining Sn²⁺ was therefore developed, based on the excellent electrochemical properties of the Au/Sn UPD system. A plot of the UPD-DPASV (differential pulse anodic stripping voltammetry) signal versus the Sn(II) concentration was obtained for [Sn(II)] of 1.98×10^–7 to 3.64×10^–5 M. The method developed here has been applied to determine the tin in a tin plate sample.     

Ultraviolet Spectrophotometric Determination of Antimony (III) Antibilharzial Compounds

Abstract

A direct UV spectrophotometric method has been developed for determination of antimony (III) antibilharzial compounds. The method has been successfully applied for the assay of five antibilharzial drugs.     

Sub-Microdetermination of Antimony (Iii) and Antimony (V) In Natural and Polluted Waters and Total Antimony In Biological Materials By Flameless Aas Following Extractive Separation With N-P-Methoxyphenyl-2-Furylacrylohydroxamic Acid

Abstract

Antimony (III) was separated from antimony (V) by extractive separation from 2–10^?6 M HC1 media with N-p-methoxyphenyl-2-furylacrylohydroxamic acid (MFHA) in chloroform and determined by graphite furnace atomic absorption spectroscopy at 2600°C using copper as matrix modifier. Antimony (V) was subsequently reduced to the trivalent form with acidic (-1M HC1) potassium iodide solution and determined as above. the mutual tolerance between antimony (III) and antimony (V) in the present mothod was very high-either of the species could be determined in presence of 15 times higher concentration of the other species. the sepatation-AAS determination system enabled accurate differential analysis of the metalloid in natural/ polluted waters down to 10^?2 ppb (ug 1^?1) levels. the method was also applied to the analysis of antimony in vehicle exhaust particulates, plant tissues, and animal tissues. the method was validated by analysing several certified reference materials with and without standard addition of antimony. MFHA was chosen from amongst thirteen new hydroxamic acids.