Ammonia gas sensor based on a spinel semiconductor,Co<Subscript>0.8</Subscript>Ni<Subscript>0.2</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanomaterial

Thick film of nanocrystalline Co_0.8Ni_0.2Fe₂O₄ was obtained by sol–gel citrate method for gas sensing application. The synthesized powder was characterized by X-ray diffraction (XRD) and transmission electron microscopy. The XRD pattern shows spinel type structure of Co_0.8Ni_0.2Fe₂O₄. XRD of Co_0.8Ni_0.2Fe₂O₄ revels formation of solid solution with average grain size of about 30 nm. From gas sensing properties it observed that nickel doping improves the sensor response and selectivity towards ammonia gas and very low response to LPG, CO, and H₂S at 280 °C. Furthermore, incorporation of Pd improves the sensor response and stability of ammonia gas and reduced the operating temperature upto 210 °C. The sensor is a promising candidate for practical detector of ammonia.     

Electrochemical properties of nano-crystalline LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> synthesized by polymer-pyrolysis method

LiNi_0.5Mn_1.5O₄ powders were prepared through polymer-pyrolysis method. XRD and TEM analysis indicated that the pure spinel structure was formed at around 450 °C due to the very homogeneous intermixing of cations at the atomic scale in the starting precursor in this method, while the well-defined octahedral crystals appeared at a relatively high calcination temperature of 900 °C with a uniform particle size of about 100 nm. When cycled between 3.5 and 4.9 V at a current density of 50 mA/g, the as prepared LiNi_0.5Mn_1.5O₄ delivered an initial discharge capacity of 112.9 mAh/g and demonstrated an excellent cyclability with 97.3% capacity retentive after 50 cycles.     

Bi<Subscript>3.25</Subscript>La<Subscript>0.75</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> powders by the complex polymerization method: synthesis,characterization and morphology

Lanthanum-modified bismuth titanate (Bi_3.25La_0.75Ti₃O₁₂, BLTO) powders were prepared by the complex polymerization method. The structure and morphology of BLTO powders were investigated by X-ray diffraction and scanning electron microscopy. The complexation of citric acid with the metallic cations was detected by Fourier transformed infrared (FT-IR). The thermal analyses of obtained gels were investigated by differential thermal gravimetric (DTG). The pure and normally stoichiometric phase of BLTO powders could be obtained at relatively low temperature of 550–700 °C even if the bismuth content is not excess in the starting precursors, while the secondary phase could be detected at lower and higher calcination temperatures. The shape of the BLTO grains is similarly to platelet in Bi-layer structure and stoichiometry BLTO was detected by the analysis of energy dispersive spectrometry.     

Thermal oxide synthesis and characterization of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanorods and Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> nanowires

Fe₃O₄ nanorods and Fe₂O₃ nanowires have been synthesized through a simple thermal oxide reaction of Fe with C₂H₂O₄ solution at 200–600°C for 1 h in the air. The morphology and structure of Fe₃O₄ nanorods and Fe₂O₃ nanowires were detected with powder X-ray diffraction, scanning electron microscopy and transmission electron microscopy. The influence of temperature on the morphology development was experimentally investigated. The results show that the polycrystals Fe₃O₄ nanorods with cubic structure and the average diameter of 0.5–0.8 μm grow after reaction at 200–500°C for 1 h in the air. When the temperature was 600°C, the samples completely became Fe₂O₃ nanowires with hexagonal structure. It was found that C₂H₂O₄ molecules had a significant effect on the formation of Fe₃O₄ nanorods. A possible mechanism was also proposed to account for the growth of these Fe₃O₄ nanorods. Supported by the Fund of Weinan Teacher’s University (Grant No. 08YKZ008), the National Natural Science Foundation of China (Grant No. 20573072) and the Doctoral Fund of Ministry of Education of China (Grant No. 20060718010)     

Facile preparation and electrochemical properties of large-scale Li<Subscript>1+<Emphasis Type="Italic">x</Emphasis></Subscript>V<Subscript>3</Subscript>O<Subscript>8</Subscript> nanobelts

Large-scale Li_1+x V₃O₈ nanobelts were successfully fabricated using filter paper as deposition substrate through a simple surface sol–gel method. The nanobelts were as long as tens of micrometers with widths of 0.4–1.0 μm and thickness of 50–100 nm. The nanobelts were characterized by X-ray diffration (XRD), Fourier infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM). The formation mechanism of the nanobelts was investigated, showing that the morphology of the nanobelts is mainly determined by the calcination temperature. Electrochemical properties of the Li_1+x V₃O₈ nanobelts were characterized by charge–discharge experiments, and the results demonstrate that the Li_1+x V₃O₈ nanobelts exhibit a high discharge capacity (278 mAh g⁻¹) and excellent cycling stability.     

Phase relations in the CoO–V<Subscript>2</Subscript>O<Subscript>5</Subscript>–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> system in subsolidus area

Thermal properties of Co₂FeV₃O₁₁ have been reinvestigated. It has been proved that this compound does not exhibit polymorphism. It melts incongruently at the temperature of 770±5°C and the phase with lyonsite type structure is the solid product of this melting. Phase relations in the whole subsolidus area of the CoO–V₂O₅–Fe₂O₃ system have been determined. The solidus area projection onto the component concentration triangle plane of this system has been constructed using the DTA and XRD methods. 15 subsidiary subsystems can be distinguished in this system.     

Synthesis and characterization of submicron size particles of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> by microemulsion route

Among the various positive electrode materials investigated for Li-ion batteries, spinel LiMn₂O₄ is one of the most important materials. Small particles of the active materials facilitate high-rate capability due to large surface to mass ratio and small diffusion path length. The present work involves the synthesis of submicron size particles of LiMn₂O₄ in a quaternary microemulsion medium. The precursor obtained from the reaction is heated at different temperatures in the range from 400 to 900 °C. The samples heated at 800 and 900 °C are found to possess pure spinel phase with particle size <200 nm, as evidenced from XRD, SEM, and TEM studies. The electrochemical characterization studies provide discharge capacity values of about 100 mAh g⁻¹ at C/5 rate, and there is a moderate decrease in capacity by increasing the rate of charge–discharge cycling. Studies also include charge–discharge cycling and ac impedance studies in temperature range from −10 to 40 °C. Impedance data are analyzed with the help of an equivalent circuit and a nonlinear least squares fitting program. From temperature dependence of charge-transfer resistance, a value of 0.62 eV is obtained for the activation energy of Mn³⁺/Mn⁴⁺ redox process, which accompanies the intercalation/deintercalation of the Li⁺ ion in LiMn₂O₄.     

Preparation of novel visible-light-driven In<Subscript>2</Subscript>O<Subscript>3</Subscript>–CaIn<Subscript>2</Subscript>O<Subscript>4</Subscript> composite photocatalyst by sol–gel method

Novel visible-light-activated In₂O₃–CaIn₂O₄ photocatalysts were developed in this paper through a sol–gel method. The photocatalytic activities of In₂O₃–CaIn₂O₄ composite photocatalysts were investigated based on the decomposition of methyl orange under visible light irradiation (λ > 400 nm). The obtained samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectrum (EDS), X-ray photoelectron spectroscopy (XPS) and UV–vis diffused reflectance spectroscopy (DRS). The results revealed that the In₂O₃–CaIn₂O₄ composite samples with different In₂O₃ and CaIn₂O₄ content can be obtained by controlling the synthesis temperature, and the composite photocatalysts extended the light absorption spectrum toward the visible region. The photocatalytic tests indicated that the composite samples demonstrated high visible-light activity for decomposition of methyl orange. The significant enhancement in the In₂O₃–CaIn₂O₄ photo-activity under visible light irradiation can be ascribed to the efficient separation of photo-generated carriers in the In₂O₃ and CaIn₂O₄ coupling semiconductors.     

2-pyrrolidone - capped Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> nanocrystals

Water-soluble Mn₃O₄ nanocrystals have been prepared through thermal decomposition in a high temperature boiling solvent, 2-pyrrolidone. The final product was characterized with XRD, SEM, TEM, FTIR and Zeta Potential measurements. Average crystallite size was calculated as ∼15 nm using XRD peak broadening. TEM analysis revealed spherical nanoparticles with an average diameter of 14±0.4 nm. FTIR analysis indicated that 2-pyrrolidone coordinates with the Mn₃O₄ nanocrystals only via O from the carbonyl group, thus confining their growth and protecting their surfaces from interaction with neighboring particles.      

Sol–gel synthesis,characterization and photocatalytic activity of mesoporous TiO<Subscript>2</Subscript>/γ-Al<Subscript>2</Subscript>O<Subscript>3 </Subscript>granules

Mesoporous TiO₂/γ-Al₂O₃ composite granules were prepared by combining sol–gel/oil-drop method, using various titania solution. The product granules can be used as a photocatalyst or adsorbent in moving, fluidized bed reactors. The phase composition and pore structure of the granules can be controlled by calcination temperature and using different titania solution. In the photocatalysis of NH₃ decomposition, TiO₂/γ-Al₂O₃ granules using Degussa P25 powder treated thermally at 450 °C showed the highest catalytic ability. However, TiO₂/γ-Al₂O₃ granules using titania made by hydrothermal method had comparable performance in NH₃ decomposition.     

Preparation of Ca<Subscript>3</Subscript>Co<Subscript>4</Subscript>O<Subscript>9</Subscript> by polyacrylamide gel processing and its thermoelectric properties

Ca₃Co₄O₉ powder was prepared by a polyacrylamide gel route in this paper. The effect of the processing on microstructure and thermoelectric properties of Ca₃Co₄O₉ ceramics via spark plasma sintering were investigated. Electrical measurement shows that the Seebeck coefficient and conductivity are 170 μV/K and 128 S/cm, respectively, at 700 °C, yielding a power factor value of 3.70 × 10⁻⁴ W m⁻¹ K⁻² at 700 °C, which is larger than that of Ca₃Co₄O₉ ceramics via solid-state reaction processing. The polyacrylamide gel processing is a fast, cheap, reproducible and easily scaled up chemical route to improve the thermoelectric properties of Ca₃Co₄O₉ ceramics by preparing the homogeneous and pure Ca₃Co₄O₉ phase.     

Formation of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–TiO<Subscript>2</Subscript> bilayer using atomic layer deposition and its application to dynamic random access memory

To enhance film conformality together with electrical property suitable for dynamic random access memory (DRAM) capacitor dielectric, the effects of oxidant and post heat treatment were investigated on aluminum and titanium oxide (Al₂O₃–TiO₂) bilayer (ATO) thin film formed by atomic layer deposition method. For the conformal deposition of Al₂O₃ thin film, the O₃ oxidant required a higher deposition temperature, more than 450 °C, while H₂O or combined oxygen sources (H₂O+O₃) needed a wide range of deposition temperatures ranging from 250 to 450 °C. Conformal deposition of the TiO₂ thin film was achieved at around 325 °C regardless of the oxidants. The charge storage capacitance, measured from the ATO bilayer (4 nm Al₂O₃ and 2 nm TiO₂) deposited at 450 °C for Al₂O₃ and 325 °C for TiO₂ with O₃ oxidant on the phosphine-doped poly silicon trench, showed about 15% higher value than that of 5 nm Al₂O₃ single layer thin film without any increase of leakage current. To maintain the improved electrical property of the ATO bilayer for DRAM application, such as enhanced charge capacitance without increase of leakage current, upper electrode materials and post heat treatments after electrode formation must be selected carefully. Dedicated to Professor Su-Il Pyun on the occasion of his 65th birthday.     

Aqueous sol–gel processing of precursor oxides for ZrW<Subscript>2</Subscript>O<Subscript>8</Subscript> synthesis

This paper describes the synthesis of ZrW₂O₈ by the use of an aqueous citrate-gel method in order to prepare a fine, pure and homogeneous oxide mixture suitable for ceramic processing. The thermal expansion coefficient thus obtained for α-ZrW₂O₈ is −10.6 × 10⁻⁶ °C⁻¹ (50–125 °C) whereas for the β-ZrW₂O₈ a value of −3.2 × 10⁻⁶ °C⁻¹ (200–300 °C) is obtained. The advantages of the use of a sol–gel method is expressed in the very homogeneous end-products. The paper describes crystallographic data, morphological structure and the thermal expansion properties of the ZrW₂O₈ material. Moreover, photoluminescence and photochromic properties specific to the precursor gel are described and analyzed. These effects support our views that the precursors show homogeneity up to nanometer level.     

A new phosphor with flower-like structure and luminescent properties of Sr<Subscript>2</Subscript>MgSi<Subscript>2</Subscript>O<Subscript>7</Subscript>: Eu<Superscript>2+</Superscript>, Dy<Superscript>3+</Superscript> long afterglow materials by sol–gel method

The flower-like phosphors of Sr₂MgSi₂O₇: Eu²⁺, Dy³⁺ with high brightness and long afterglow were obtained by sol–gel method. X-ray diffraction pattern (XRD) shows that single-phased Sr₂MgSi₂O₇ phosphor is prepared by sol–gel method under 1250 °C. Scanning electron microscope (SEM) indicates that the phosphor consists of nano-sized whiskers which are detected for the first time in Eu²⁺ and Dy³⁺ co-doped long-lasting phosphorescence silicates. Furthermore, the investigation on the mechanism indicates that the internal structure and gas, liquid and solid phase effect play important roles in the formation of flower-like Sr₂MgSi₂O₇: Eu²⁺, Dy³⁺ nanostructure. Finally, the optical properties of flower-like Sr₂MgSi₂O₇ nanostructure have been characterized by photoluminescence (PL) spectra.     

Luminescent characteristics and microstructures of Sr<Subscript>2</Subscript>CeO<Subscript>4</Subscript> phosphors prepared via sol–gel and solid-state reaction routes

Blue-light-emitting Sr₂CeO₄ phosphors were synthesized via a sol–gel process and the conventional solid-state method in this study. The developed sol–gel process lowered the synthesis temperature of monophasic Sr₂CeO₄ to as low as 900 °C. In comparison with the solid-state derived powders, the sol–gel derived powders had more uniform morphology and smaller particle sizes. In addition, sol–gel derived Sr₂CeO₄ displayed higher luminescent intensity than that prepared via the solid-state route under the same heating conditions. This is attributed to the improved compositional homogeneity and crystallinity in the sol–gel process. During the heating processes, Sr₂CeO₄ tended to thermally decompose at elevated temperatures. This decomposition reaction resulted in the formation of an impurity phase- SrCeO₃ and thereby a decrease in the luminescent intensity. For obtaining Sr₂CeO₄ phosphors with high luminescent intensity, the heating conditions in both processes need to be well modulated.     

Two color up-conversion emissions of Er<Superscript>3+</Superscript>-doped Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanopowders prepared by non-aqueous sol-gel method

Er³⁺-doped Al₂O₃ nanopowders have been prepared by the non-aqueous sol-gel method using the aluminum isopropoxide as precursor, acetylacetone as a chelating agent, nitric acid as a catalyzer, and hydrated erbium nitrate as a dopant under isopropanol environment. The different phase structure, including three crystalline types of (Al, Er)₂O₃ phases, α, γ, θ, and an Er–Al–O stoichiometric compound phase, Al₁₀Er₆O₂₄, was observed for the 0.01–0.5 mol% Er³⁺-doped Al₂O₃ nanopowders at the sintering temperature of 1,000 °C. The green and red up-conversion emissions centered at about 523, 545 and 660 nm, corresponding respectively to the ²H_11/2, ⁴S_3/2→⁴I_15/2 and ⁴F_9/2→⁴I_15/2 transitions of Er³⁺, were detected by a 978 nm semiconductor laser diodes excitation. With increasing Er³⁺ doping concentration from 0.01 to 0.1 mol%, the intensity of the green and red emissions increased with a decrease of the intensity ratio of the green to red emission. When the Er³⁺ doping concentration rose to 5 mol%, the intensity of the green and red emissions decreased with an increase of their intensity ratio. The maximum intensity of both the green and red emissions with the minimum of intensity ratio was obtained, respectively, for the 0.1 mol% Er³⁺-doped Al₂O₃ nanopowders composed of a single α-(Al,Er)₂O₃ phase. The intensity ratio of the green emission at 523 and 545 nm increased monotonously for all Er³⁺ doping concentrations. The two-photon absorption up-conversion process was involved in the green and red up-conversion emissions of the Er³⁺-doped Al₂O₃ nanopowders.     

Comparative study of the synthesis of CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript> and NiFe<Subscript>2</Subscript>O<Subscript>4</Subscript> in silica through the polymerized complex route of the sol–gel method

In this work the synthesis of CoFe₂O₄-SiO₂ and NiFe₂O₄-SiO₂ nanocomposites was studied via the sol–gel method, using the polymerized complex route. The polymerized precursors obtained by the reaction of citric acid, ethylene glycol, tetraethylorthosilicate, ferric nitrate, and cobalt nitrate or nickel chloride were characterized by nuclear magnetic resonance (NMR) and infrared (IR) spectroscopy. NMR and IR spectra of the precursors, without and with metallic ions, show the formation of polymeric chains with ester and ether groups and complexes of metal-polymeric precursor. The nanocomposites were obtained by the thermal decomposition of the organic fraction and characterized by X-ray diffraction (XRD) and vibrating sample magnetometry (VSM). XRD patterns show the formation of CoFe₂O₄ and NiFe₂O₄ in an amorphous silica matrix above 400 °C in both cases. When the calcination temperature was 800 °C the particle size of the crystalline phases, calculated using the Scherrer equation, reached ∼35 nm for the two oxides. VSM plots show the ferrimagnetic behavior that is expected for this type of magnetic material; the magnetization at 12.5 KOe of the CoFe₂O₄-SiO₂ and NiFe₂O₄-SiO₂ compounds was 29.5 and 17.4 emu/g, respectively, for samples treated at 800 °C.     

Effect of metal substitution for cobalt on the oxygen adsorption properties of YBaCo<Subscript>4</Subscript>O<Subscript>7</Subscript>

YBaCo₄O₇ compound is capable to intake and release a large amount of oxygen in the temperature range of 200–400°C. In the present study, the effect of Zn, Ga and Fe substitution for Co on the oxygen adsorption/desorption properties of YBaCo₄O₇ were investigated by thermogravimetry (TG) method. Due to fixed oxidation state of Zn2+ ions, the substitution of Zn²⁺ for Co²⁺ suppresses the oxygen adsorption of YBaCo_4−xZn_xO₇. The substitution of Ga³⁺ for Co³⁺ also decreases the oxygen absorption capacity of YBaCo_4−xGa_xO₇. This can be explained by the strong affinity of Ga³⁺ ions towards the GaO₄ tetrahedron. Compared with Zn- and Ga-substituted samples, the drop of oxygen adsorption capacity is smallest for Fe-substituted samples because of the similar changeability of oxidation states of Co and Fe ions.     

Formation and properties of the Fe<Subscript>8</Subscript>V<Subscript>10</Subscript>W<Subscript>16–x</Subscript>Mo<Subscript>x</Subscript>O<Subscript>85</Subscript> type solid solution

Solid solution phases of a formula Fe₈V₁₀W_16–xMo_xO₈₅ where 0≤x≤4, have been obtained, possessing a structure of the compound Fe₈V₁₀W₁₆O₈₅. It was found on the base of XRD and DTA investigations that these solution phases melted incongruently, with increasing the value of x, in the temperature range from 1108 (x=0) to 1083 K (x=4) depositing Fe₂WO₆ and WO₃. The increase of the Mo⁶⁺ ions content in the crystal lattice of Fe₈V₁₀W₁₆O₈₅ causes the lattice parameters a=b contraction with cbeing almost constant. IR spectra of the Fe₈V₁₀W_16–xMo_xO₈₅ solid solution phases have been recorded.     

Preparation and electrochemical properties of V<Subscript>2</Subscript>O<Subscript>5</Subscript> submicron-belts synthesized by a sol–gel H<Subscript>2</Subscript>O<Subscript>2</Subscript> route

One-dimensional (1D) submicron-belts of V₂O₅ have been prepared by a sol–gel route using V₂O_5, H₂O₂ and aniline as starting materials. Thermogravimetric and differential thermal analysis, X-ray diffraction, Fourier transform infrared spectroscopy and scanning electron microscopy were employed to characterize the samples. Electrochemical behaviors as cathode material in rechargeable lithium-ion batteries were investigated by galvanostatic charge–discharge measurement and cyclic voltammeter. The results showed that the synthesized V₂O₅ appeared to be submicron-belts and orthorhombic structure. The V₂O₅ submicron-belts exhibited a high initial discharge capacity of 346 mAh/g and stayed 240 mAh/g after 20 cycles at 0.1 C discharge rate in the potential region 1.8–4.0 V.