常温直接沉淀法制备ZnO纳米棒

在常温下, 以PEG-400(聚乙二醇400)为表面活性剂, 采用直接沉淀法合成了ZnO纳米棒. 产物用XRD, TEM, SAED和 HRTEM等进行了表征. 结果表明, 所得ZnO为一维的纳米棒, 属于六方纤维矿的单晶结构. ZnO纳米棒的直径在20~40 nm之间, 长度在300~800 nm范围. (0001)面为ZnO纳米棒的生长方向. 讨论了ZnO相的生成和ZnO纳米棒的形成机理以及PEG-400在其形成过程中的作用.     

Spectroscopic characterization of zinc oxide nanorods synthesized by solid-state reaction

Well-crystallized zinc oxide nanorods have been fabricated by single step solid-state reaction using zinc acetate and sodium hydroxide, at room temperature. The sodium lauryl sulfate (SLS) stabilized zinc oxide nanorods were characterized by using X-ray diffraction, Fourier transform infrared spectroscopy, transmission electron microscopy and photoluminescence spectroscopy. The X-ray diffraction revealed the wurtzite structure of zinc oxide. The size estimation by XRD and TEM confirmed that the ZnO nanorods are made of single crystals. The growth of zinc oxide crystals into rod shape was found to be closely related to its hexagonal nature. The mass ratio of SLS:ZnO in the nanorods was found to be 1:10 based on the thermogravimetric analysis. Blue shift of photoluminescence emission was noticed in the ZnO nanorods when compared to that of ZnO bulk. FT-IR analysis confirmed the binding of SLS with ZnO nanorods. Apart from ease of preparation, this method has the advantage of eco-friendliness since the solvent and other harmful chemicals were eliminated in the synthesis protocol.     

电沉积制备ZnO纳米棒修饰电极上氧化还原蛋白的电化学行为

采用恒电位阴极还原法在金电极表面一步修饰ZnO纳米棒, 制备成ZnO纳米棒修饰电极. 扫描电子显微镜(SEM)和X射线衍射(XRD)结果显示制得的ZnO为直径约100 nm的六棱柱状纤锌矿晶体纳米棒. 使用ZnO纳米棒修饰的金电极研究细胞色素c的直接电化学行为, 结果表明: ZnO纳米棒修饰的金电极能有效探测到细胞色素c的铁卟啉辅基在不同价态下的电化学行为; 细胞色素c吸附后, ZnO纳米棒修饰的金电极对过氧化氢的电流响应呈现良好的线性关系.     

Preparation of zinc oxide nanorods using pulsed laser ablation in water media at high temperature

ZnO columnar single crystals were formed by pulsed laser ablation in deionized water and surfactant aqueous solutions of lauryl dimethylaminoacetic acid (LDA) and cetyltrimethylammonium bromide (CTAB) at 80 degrees C. ZnO particles produced by laser ablation were dissolved at a higher temperature than 60 degrees C, and then crystalline growth to columnar structure proceeded. While large ZnO columnar crystals were obtained in deionized water, the crystals prepared in surfactant solution were smaller than those in deionized water due to inhibition of crystalline growth by surfactant adsorption on ZnO surfaces. The size of ZnO nanorods depended on how surfactant molecules adsorb on ZnO surface.     

低温一步液相法合成ZnO纳米棒

近年来．一维纳米结构如纳米线、纳米棒、纳米带等．由于其新颖的物理化学性质及其在光学或电学器件上的广泛应用前景．已成为研究开发的热点。特别是氧化锌（ZnO）这种宽禁带（3．37eV）、高激子束缚能（60meV）的功能性半导体材料。基于它在光电子器件、太阳能电池、传感器、二极管、场发射显示器等领域潜在的重要应用价值，各国科学工作者都给予极大的研究热情．开发出了许多合成方案制备一维纳米ZnO结构，如水热法，模板法同，微乳液法阐，CVD法，热蒸发法，MOVPE法，电化学沉积法等。     

Synthesis of variable-aspect-ratio, single-crystalline ZnO nanostructures

Variable-aspect-ratio (length/diameter), one-dimensional (1-D) ZnO nanostructures (nanorods and nanowires) were prepared in alcohol/water solution by reacting a Zn2+ precursor with an organic weak base, tetramethylammonium hydroxide (Me4NOH). The effect of the experimental parameters (temperature, base concentration, reaction time, and water content) on nucleation, growth, and the final morphology of the ZnO nanostructures was investigated. The low-temperature syntheses (75-150 degrees C) yielded aspect ratios of the 1-D ZnO nanostructures that depended on the water content. The individual ZnO nanorods and nanowires were determined to be perfect, single crystals with their c axes as the primary growth direction.     

水热法制备高度取向的氧化锌纳米棒阵列

氧化锌的激子结合能(60meV)及光增益系数(300cm^-1)比GaN的(25meV,100cm^-1)还高,这一特点使它成为紫外半导体激光发射材料的研究热点。最近,Yang等成功地观测到规则的ZnO纳米线阵列的激光发射现象,更加激起了人们合成一维高度有序ZnO纳米结构的热情,由于一维ZnO     

Effect of seeded substrates on hydrothermally grown ZnO nanorods

We report a study on the effect of seeding on glass substrates with zinc oxide nanocrystallites towards the hydrothermal growth of ZnO nanorods from a zinc nitrate hexahydrate and hexamethylenetetramine solution at 95 °C. The seeding was done with pre-synthesized ZnO nanoparticles in isopropanol with diameters of about 6–7 nm as well as the direct growth of ZnO nanocrystallites on the substrates by the hydrolysis of pre-deposited zinc acetate film. The nanorods grown on ZnO nanoparticle seeds show uniform dimensions throughout the substrate but were not homogenously aligned vertically from the substrate and appeared like nanoflowers with nanorod petals. Nanorods grown from the crystallites formed in situ on the substrates displayed wide variations in dimension depending upon the preheating and annealing conditions. Annealing the seed crystals below 350 °C led to scattered growth directions whereupon preferential orientation of the nanorods perpendicular to the substrates was observed. High surface to volume ratio which is vital for gas sensing applications can be achieved by this simple hydrothermal growth of nanorods and the rod height and rod morphology can be controlled through the growth parameters.     

The effect of hydrothermal growth temperature on preparation and photoelectrochemical performance of ZnO nanorod array films

Highly oriented ZnO nanorod arrays with controlled diameter and length, narrow size distribution and high orientation consistency have been successfully prepared on ITO substrates at different growth temperatures by using a simple hydrothermal method. XRD results indicate that the nanorods are high-quality single crystals growing along [001] direction with a high consistent orientation perpendicular to the substrate. SEM images show that the nanorods have average diameters of about 30-70 nm by changing growth temperature. The thin films consisting of ZnO nanorods with controlled orientation onto ITO substrates allow a more efficient transport and collection of photogenerated electrons through a designed path. For a sandwich-type cell, the relatively high overall solar energy conversion efficiency reaches about 2.4% when the growth temperature is at 95 °C.     

Unidirectional Alignment of Surface-Grafted ZnO Nanorods in Micrometer-Thick Cells Using Low-Molecular-Weight Liquid Crystals

Inorganic nanomaterials such as nanotubes and nanorods have attracted great attention due to their anisotropic properties. Although the alignment control of inorganic nanomaterials is key to the development of functional devices utilizing their fascinating properties, there is still difficulty in achieving uniform alignment over a large area with a micrometer thickness. To overcome this problem, we focused on liquid crystals (LCs) to promote the alignment of anisotropic nanomaterials, taking advantage of the cooperative motion of LCs. We present the uniform, one-dimensional alignment of ZnO nanorods along the direction of LCs in micrometer-thick cells by grafting nematic LC polymers from the nanorod surfaces to provide miscibility with the host LCs. Polarized optical microscopy and polarized UV–visible absorption spectroscopy revealed the unidirectional alignment of nematic LC polymer-grafted ZnO nanorods parallel to the nematic host LCs.     

The Development of Highly Sensitive and Selective Immunosensor Based on Antibody Immobilized ZnO Nanorods for the Detection of D‐Dimer

ZnO nanorods were grown on gold coated glass substrate by low temperature aqueous chemical growth method. Scanning electron microscopy (SEM) and X‐ray diffraction (XRD) techniques were used for the characterization of ZnO nanorods. ZnO nanorods are highly dense, uniform, well aligned and perpendicular‐oriented to the substrate. ZnO nanorods exhibited good crystal quality. The well aligned ZnO nanorods were potentially used for the development of selective and sensitive immunosensor for the detection of D‐dimer by immobilizing antibody on stabilized lipid films. The ZnO nanorods based immunosensor responded to a wide range of D‐dimer concentrations with fast response time of ca. 20 s.     

Enhanced Raman scattering and photocatalytic activity of Ag/ZnO heterojunction nanocrystals

In this work, we study the enhancement of Raman signals and photocatalytic activity of Ag/ZnO heterojunctions with an Ag content of 1 at.%, which were synthesized by photochemical deposition of Ag nanoparticles onto pre-synthesized ZnO nanorods. A strong interaction between Ag and ZnO nanocrystals were evidenced by XPS and UV-vis spectroscopy. The binding energy of Ag nanoparticles shifts toward lower energy compared to that of pure Ag nanoparticles, revealing that electrons transfer from Ag to the ZnO nanocrystals. The red shift of the plasmon absorption peak of Ag nanoparticles in Ag/ZnO heterojunctions further confirms the strong interaction between the two components. This strong interaction, arising from the coupling between Ag and ZnO nanocrystals, is responsible for the enhancement of Raman signals and photocatalytic activity of the Ag/ZnO heterojunctions.     

Pt纳米花/ZnO复合阵列的制备及对甲醇氧化催化的研究

利用调控ZnO纳米棒阵列的疏水、亲水性,由电化学方法制备了Pt纳米花/ZnO(PtNF/ZnO)复合阵列.该复合阵列排列规则、尺寸均一、方向一致.每一根ZnO纳米棒的顶端都覆盖着由Pt纳米颗粒构成的Pt纳米花,具有大的比表面积.与以亲水性的ZnO纳米棒制得的覆盖Pt纳米颗粒的ZnO复合阵列(PtNP/ZnO)以及单独的Pt颗粒相比,PtNF/ZnO复合阵列对甲醇氧化具有更高的电化学催化活性.     

Straight and thin ZnO nanorods: hectogram-scale synthesis at low temperature and cathodoluminescence

A novel seed-assisted chemical reaction at 95 degrees C has been employed to synthesize uniform, straight, thin, and single-crystalline ZnO nanorods on a hectogram scale. The molar ratio of ZnO seed and zinc source plays a critical role in the preparation of thin ZnO nanorods. At a low molar ratio of ZnO seed and zinc source, javelin-like ZnO nanorods consisting of thin ZnO nanorods with a diameter of 100 nm and thick ZnO nanorods with a diameter of 200 nm have been obtained. In contrast, straight ZnO nanorods with a diameter of about 20 nm have been prepared. Dispersants such as poly(vinyl alcohol) act spatial obstructors to control the length of ZnO nanorods. The morphology, structure, and optical property of the ZnO nanostructures prepared under different conditions have been characterized by transmission electron microscopy, field emission scanning electron microscopy, X-ray powder diffraction, high-resolution transmission electron microscopy, and cathodoluminescence. The formation mechanisms for the synthesized nanostructures with different morphologies have been phenomenologically presented.     

Flowerlike ZnO nanostructures via hexamethylenetetramine-assisted thermolysis of zinc-ethylenediamine complex

Flowerlike ZnO nanostructures (FZNs) have been deposited on Si substrate from aqueous solution by the hexamethylenetetramine (HMT)-assisted thermolysis of zinc-ethylenediamine (en) complex at low temperature (95 degrees C) and in a short time (60 min). Obtained FZNs exhibit well-defined flowerlike morphology, hexagonal wurtzite structure, and strong UV photoluminescence. The flower petals constructed by many well-aligned nanorods possess the typical tapering feature with tip sizes of 30-50 nm. Effects of en, zinc-en molar ratio, HMT, and reaction time were investigated. Results show that en is determinative to the formation of FZNs, and the partial capping of NH(3).(CH(2))(2).NH(3) molecules on the side surface of the ZnO crystal is responsible for the tapering feature of petals. HMT can step into the nucleation process of ZnO and inhibit the formation of nanorods on the substrate by preventing heterogeneous precipitation. Moreover, the formation of twin crystal ZnO nuclei at low precursor concentrations and their further evolution into spindle crystals with clear middle interfaces are also vitally important for the development of FZNs.     

ZnO nanorods on ZnO seed layer derived by sol–gel process

Well-aligned ZnO nanorods are obtained by a liquid phase epitaxial growth on the indium-doped tin oxide glass deposited with a ZnO thin film as the seed layer, which is prepared by combining a sol–gel process and a spin coating technique. The effects of water content in the sol and heat treatment temperature on the properties of the ZnO thin film are investigated. Relationship among the seed layer, the growing time, the growing temperature, the concentration of Zn²⁺ in the solution, the anions in the solution and the resulting ZnO nanorods are discussed in detail. X-ray diffraction analysis and scanning electronic microscopy are employed to characterize the structural and morphological properties of the resulting ZnO nanorods. Results indicate that the ZnO nanorods with a preferred orientation show a single crystal with a wurtzite structure in the direction of [0001], the diameter of the ZnO nanorods seems to depend on the size of the seed grain, while the length of the ZnO nanorods is determined by the growing time and the growing temperature.     

From Zn-Al layered double hydroxide to ZnO nanostructure:Gradually etching by sodium hydroxide

Zn-Al layered double hydroxide(LDH) was used as precursor to produce ZnO nanostructures through dissolution of aluminum hydroxide in caustic soda.The Zn-Al LDH could transform into different nanostructures of ZnO on LDH nanosheets and even pure ZnO nanorods under various NaOH concentration.The formed ZnO nanorods vertically aligned on both LDH sides.UV-vis diverse reflectance spectra show that the obtained ZnO nanorods have a band gap of approximately 3.05 eV.Such ZnO/LDH nanostructures might be used as photocatalyst in the organic pollutant decomposition.     

Low-temperature growth of ZnO nanorods by chemical bath deposition

Aligned ZnO nanorod arrays were synthesized using a chemical bath deposition method at normal atmospheric pressure without any metal catalyst. A simple two-step process was developed for growing ZnO nanorods on a PET substrate at 90-95 degrees C. The ZnO seed precursor was prepared by a sol-gel reaction. ZnO nanorod arrays were fabricated on ZnO-seed-coated substrate. The ZnO seeds were indispensable for the aligned growth of ZnO nanorods. The ZnO nanorods had a length of 400-500 nm and a diameter of 25-50 nm. HR-TEM and XRD analysis confirmed that the ZnO nanorod is a single crystal with a wurtzite structure and its growth direction is [0001] (the c-axis). Photoluminescence measurements of ZnO nanorods revealed an intense ultraviolet peak at 378.3 nm (3.27 eV) at room temperature.     

离子液体中ZnO纳米棒的制备与表征

离子液体中ZnO纳米棒的制备与表征;离子液体;ZnO纳米棒;热分解     

Influence of different substrates on ZnO nanorod arrays properties

Zinc Oxide (ZnO) nanorod arrays were grown on different substrates by hydrothermal method. The crystallinity of ZnO nanorod was regularly investigated by X-ray diffraction (XRD). Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to examine morphology of the ZnO nanorods. The results indicate that the nanorods grow along [002] orientation. SEM and TEM images and XRD patterns show that the growth of ZnO nanorods on graphene/Quartz substrate is better than the other substrates due to the number and size of the nanorods which are highly affected through the properties of ZnO seed layers and it has lower defects than the other substrates. PL spectra ZnO would have a higher concentration of oxygen vacancy.