Antioxidative stabilization of poly(vinyl chloride)

Halogenated resins such as poly(vinyl)chloride undergo rapid degradation when exposed to heat. Such degradation is significantly increased by oxygen, and it is believed that the induction of the process of decomposition is caused by autoxidation of the polymer, followed by extensive dehydrohalogenation. Sulfur-containing peroxide decomposers allow primary stabilization of PVC with organic compounds which are not HCl acceptors but prevent free radical cross-linking of the polymer. This implies a discolored polymer melt (due to loss of HCl and formation of polyenes) which nonetheless exhibits good long term stability (no cross-linking). The stabilization of labile chlorine atoms results from the oxidation of various chain irregularities, and thus the elimination of the early discoloration can be achieved by the use of small quantities of monohydrocarbyltin co-stabilizers. The relative performance of various antioxidant systems are reported and possible stabilization mechanisms are discussed.     

Analytical approach to the discoloration of edible laver "nori" in the Ariake Sea.

To understand the cause of discoloration of the sea laver "nori," which is found in the Ariake Sea, the concentrations of pigments and elements in the normal and discolored laver samples were determined. In the discolored samples, a decrease in all of the pigments, chlorophyll a and carotenoids, and proteinous pigments, phycobiliproteins, was clearly observed. This was accompanied by a decrease in the content of Fe, Zn, Mn, Cu, and P. Good correlations between these elements and chlorophyll a, as well as between these elements and phycobiliproteins, were confirmed, indicating that, in addition to the deficiency of nitrogen and phosphorus, the deficiency of trace elements (Fe, Zn, Mn, and Cu), which are specifically required for photosynthesis, could be a reason for the discoloration of nori. The cause of elemental deficiency is also discussed.     

Retardation of discoloration of poly(vinyl chloride) and decolorization of discolored poly(vinyl chloride) with diimide

Retardation of discoloration of poly(vinyl chloride) with diimide was studied in dimethylformamide at 130°C. with the use of p-toluenesulfonylhydrazide (PSH) as a source of diimide. A process was proposed that involved prolonging the induction periods of discoloration by inhibiting the development of conjugated polyene structure. The optimum proportion of PSH was one fourth of the poly(vinyl chloride), the best results. Furthermore, poly(vinyl chloride) discolored by thermal degradation in o-dichlorobenzene or gamma-ray irradiation under vacuum was decolorized in solution at 130°C. by addition of PSH. The decolorized poly(vinyl chloride) thus obtained was thermally stable compared with that obtained by oxidative methods.     

Optimizing the sputter deposition process of polymers for the Storing Matter technique using PMMA

Quantitative analyses in secondary ion mass spectrometry (SIMS) become possible only if ionization processes are controlled. The Storing Matter technique has been developed to circumvent this so‐called matrix effect, primarily for inorganic samples, but has also been extended to organic samples. For the latter, it has been applied to polystyrene in order to investigate the extent of damage in the polymer, its fragmentation during the sputter deposition process and the effect of the deposition process on the spectra taken by Time‐of‐Flight SIMS (ToF‐SIMS). In this work, a multi‐technique approach, which employs the Storing Matter technique for deposition and ToF‐SIMS and X‐ray photoelectron spectroscopy for characterization, is used to enhance the control of the deposition process, including the thickness of the deposit, the alteration of the source film and the influence of polymer composition on the Storing Matter process. Poly (methyl methacrylate) (PMMA) is used for this work. More detailed information about the sticking of polymer fragments on the metal collector is obtained by density functional theory calculations. This work allows for the conclusion that a part of the fragments deposited on the collector surface diffuses on the latter, reacts and recombines to form larger fragments. The behaviour observed for PMMA is similar to polystyrene, showing that oxygen has no major influence on the processes occurring during the sputter deposition process. Additionally, we have developed a new methodology using 2D ToF‐SIMS images of the deposit to monitor the deposit thickness and to identify surface contaminations. The latter are not only located at the position of the deposit but all over the collector surface. Copyright © 2016 John Wiley & Sons, Ltd.     

Application of TGA/DTA/MS to the Historic Preservation of Stone

The combined technique TGA/DTA/MS, thermogravimetric analysis/differential thermal analysis/mass spectrometry, has been used, in conjunction with other analytical techniques, FTIR, SEM, XRD, and optical microscopy, to analyze a specific patching material that had become seriously discolored on its surface after being used to repair a historic stone pillar at Bethesda Terrace in Central Park, New York in the 1980s. The stone patch was found to contain a polyacrylate binder which was associated with the discoloration.This revised version was published online in November 2005 with corrections to the Cover Date.     

A Strategy for Control of "Random" Copolymerization of Lactide and Glycolide: Application to Synthesis of PEG-b-PLGA Block Polymers Having Narrow Dispersity

Poly(lactic-co-glycolic acid) (PLGA) is a biodegradable copolymer that is also acceptable for use in a variety of biomedical applications. Typically, a random PLGA polymer is synthesized in a bulk batch polymerization using a tin-based catalyst at high temperatures. This methodology results in relatively broad polydispersity indexes (PDIs) due to transesterification, and the polymer product is often discolored. We report here the use of 1,8-diazabicyclo[5.4.0]-undec-7-ene (DBU), a known, effective, and convenient organocatalyst for the ring-opening polymerization of cyclic esters, to synthesize random copolymers of lactide and glycolide. The polymerization kinetics of the homo- and copolymerizations of lactide and glycolide were explored via NMR spectroscopy. A novel strategy that employs a controlled addition of the more reactive glycolide monomer to a solution containing the lactide monomer, the poly(ethylene glycol) (PEG) macroinitiator, and DBU catalyst was developed. Using this tactic (semi-batch polymerization), we synthesized a series of block copolymers that exhibited excellent correlation of the expected and observed molecular weights and possessed narrow PDIs. We also measured the thermal properties of these block copolymers and observed trends based on the composition of the block copolymer. We also explored the need for experimental rigor in several aspects of the preparations and have identified a set of convenient reaction conditions that provide polymer products that retain the aforementioned desirable characteristics. These polymerizations proceed rapidly at room temperature and without the need for tin-based catalysts to provide PEG-b-PLGAs suitable for use in biomedical investigations.     

A pre-concentration procedure employing a new imprinted polymer for the determination of copper in water

This work describes the development by response surface methodology (RSM) of a procedure for copper determination by inductively coupled plasma optical emission spectrometry (ICP OES) in water samples after extraction by copper imprinted polymer. Results of the two-level full factorial design (2⁴) based on an analysis of variance demonstrated that only the solution pH; amount of polymer and adsorption time were statistically significant. Optimal conditions for the extraction of copper samples were obtained by using Box-Behnken design. Solution pH; amount of polymer and adsorption time were regarded as factors in the optimisation study. The working conditions were 4.6, 0.03?g and 3.5?h, for solution pH, amount of polymer; and adsorption time, respectively. Under the optimised experimental conditions, the detection limit of the proposed method followed by ICP OES was found to be 0.8?µg?L^?1. The relative standard deviation (RSD) was found to less than 0.81%. The pre-concentration factor was 22.5. The accuracy of the optimised procedure was evaluated by analysis of certified reference material. The method was applied to the determination of copper in water samples.     

Ambient ionisation mass spectrometry for the characterisation of polymers and polymer additives: A review

The purpose of this review is to showcase the present capabilities of ambient sampling and ionisation technologies for the analysis of polymers and polymer additives by mass spectrometry (MS) while simultaneously highlighting their advantages and limitations in a critical fashion. To qualify as an ambient ionisation technique, the method must be able to probe the surface of solid or liquid samples while operating in an open environment, allowing a variety of sample sizes, shapes, and substrate materials to be analysed. The main sections of this review will be guided by the underlying principle governing the desorption/extraction step of the analysis; liquid extraction, laser ablation, or thermal desorption, and the major component investigated, either the polymer itself or exogenous compounds (additives and contaminants) present within or on the polymer substrate. The review will conclude by summarising some of the challenges these technologies still face and possible directions that would further enhance the utility of ambient ionisation mass spectrometry as a tool for polymer analysis.     

Mechanosynthesis of a Copper complex for redox initiating systems with a unique near infrared light activation

The first use of a new mechanosynthesized copper complex (Cu(acac)(2dppba)) as a initiator for the redox and redox photoactivated polymerization of methacrylates under air is proposed. This paper (i) describes the mechanosynthesis of this complex, (ii) outlines the relative efficiency of the complex for redox polymerization (mechanosynthesized product vs. solvent synthesized product), (iii) follows the polymerization enhancement under a 405 nm light, and (iv) demonstrates the high performance of this complex in near infrared photoactivated redox polymerization where a completely colorless polymer is obtained (unprecedented under NIR irradiations, 785 nm, here). The light activated polymerization exhibit higher conversions, better time controls (activation control) and higher surface conversions than redox polymerization. The mechanosynthesis is well characterized by two solvent‐free methods (visual color change and Electron Spin Resonance) and two solvent‐based methods (high resolution‐electrospray ionization‐mass spectrometry (HR‐ESI‐MS) and UV–vis spectrometry). The involved mechanisms are discussed. Mechanosynthesis of copper complexes opens new perspectives for copper (photo)redox polymerization catalysts as the environmental impact and economical costs of the complex synthesis are significantly reduced. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 3646–3655     

Evaluation of Photocatalytic Activity by Dye Decomposition

A novel rapid evaluation method for the photocatalytic activity of TiO₂ thin films was developed. An organic dye with a polyvinyl alcohol (PVA) binder was spin coated on the TiO₂ thin film, and the decrease in the absorbance of the dye's absorption peak during UV light irradiation was measured. Acid Blue 9 (Brilliant Blue FCF; CI-42090) could be used as the probe, while Methylene Blue (CI-52015) was not applicable to this method because of the reversible color change after the UV irradiation was stopped. PVA has virtually no interaction with oxidizing radicals, therefore, it is regarded as a simple binder holding dye molecules in the coated dye-PVA film. It was found that the ambient humidity during the UV irradiation strongly accelerates the discoloration rate of the dye, probably due to the increase in the photogenerated oxidizing radicals on the TiO₂ surface. This dye discoloration could be explainedby the one-dimensional diffusion model with a first order reaction.     

A novel method of the determination of boron in the presence of a little methanol by discoloring spectrophotometry in pharmaceutical and biological samples

It is the first time that boron is determined in the presence of a little methanol by discoloring spectrophotometry in this paper. A russety product can be formed by the reaction between glycine (Gly) and sodium 1,2-naphthoquinone-4-sulfonate (NQS) in alkaline solution. When boron is added to the solution, the system will be discolored, and the addition of a little methanol will improve the discoloration. Beer's law is obeyed in the range of boron concentrations of 0.86-43.24 μg ml⁻¹ at the maximal discoloring wavelength of 382 nm. The equation of linear regression is A = −0.07581-86.79186C (mol l⁻¹), with a linearly correlation coefficient of 0.9979. The detection limit is 0.80 μg ml⁻¹ and R.S.D. is 4.2%. The method is successfully applied to the determination of boron in pharmaceutical and biological samples. The average recoveries are in the range of 98.2-104.1%. Analytical results obtained with this novel method are satisfactory.     

Influence of individual ionic components on the agglomeration kinetics of silver nanoparticles

We demonstrate an original and powerful concept for elaborating spontaneous, high fidelity patterns of nanoporosity from nanoscale building blocks using patterned surface chemistry (i.e., "surface energy gating") to corral the growth of colloidal structures at a solid surface. Composite films consisting of polymethylsilsesquioxane nanoparticles uniformly dispersed in polypropylene glycol polymer were examined at temperatures beyond the decomposition of the polymer as a function of the substrate surface energy to clarify nanoparticulate ensemble behavior. The principle behind this colloidal assembly can be understood by taking into consideration the entropy and enthalpy dictating the mutual interactions between substrate surface, polymeric solvent, and dispersed colloids in the decomposition regime. The relevance of this research is shown by demonstrating how the principle of surface energy gating can be utilized to achieve spontaneous and controllable spatial patterns of nanoporous, high surface area thin films in a cost-effective and energy-efficient manner via brief thermal exposure. The simplicity and general nature of this methodology are further exemplified by showing the facility with which high-contrast fluorescent bioconjugate arrays can be prepared from nanoporous organosilicate patterns.     

CR@BaSO4: an acid rain-indicating material

The CR@BaSO(4) hybrid was synthesized, characterized and used as an acid rain-indicating (ARI) material. A painted ARI umbrella was discolored after exposure to simulated acid rain of pH 5 or less and returned to the initial color after the rain stopped. Such a functionalized material may make acid rain visual to remind people in real-time.     

Molecular imprinted membrane biosensor for pesticide detection: Perspectives and challenges

Polymers are crucial component for modern sensor devices. However, comprehensive research on polymer sensor technology is still going strong. Molecular imprinted membrane (MIM) is a great design that demonstrates acceptable recognition ability when integrated with a sensing transducer. Generally, the detection technique that has been widely and sparingly used for pesticide is mass spectrometry merged with gas and/or liquid chromatography. Nevertheless, this review focuses not on these common methods but on the specific methodology of MIM biosensor for the analysis of pesticides. Finally, the transduction schemes of the MIM sensor are reviewed. The interest of this article is sketched to the trends and challenges present in this field of study.     

Inactivation of Food-borne Spoilage and Pathogenic Micro-organisms on the Surface of a Photoactive Polymer

The photodynamic action of a novel photoactive polymer comprising covalently bound anthraquinone (AQ) moieties was evaluated after developing a methodology to reliably immobilize viable micro-organisms onto polymer film surfaces. The survival of Escherichia coli, Bacillus cereus (vegetative cells and spores), Fusarium oxysporum and Saccharomyces cerevisiae microbes inoculated on the surface of inert polymeric substrates was assessed to determine the effect of inoculum composition, drying rate and exposure to ultraviolet (UV-A) radiation. Their survival was highly dependent on microbial genus, with E. coli consistently displaying markedly shorter survival times than the other microbes, and B. cereus spores being the most resistant. Inoculation of the microbes onto the surface of the photoactive polymer films, followed by exposure to UV-A radiation, dramatically accelerated the inactivation of all microbial types studied compared with their survival on the surface of inert polymer substrates. Simultaneous exposure to both oxygen and UV-A radiation is required to affect cell survival, which is consistent with this effect most likely originating from the photoinduced production of singlet oxygen by the photoactive polymer. These results provide further compelling evidence that singlet oxygen produced exogenously by this photoactive polymeric substrate can successfully inactivate a broad spectrum of microbes on the substrate’s surface.     

Continuous self-avoiding walk with application to the description of polymer chains

We develop the continuous self-avoiding walk (CSAW) methodology for investigating temperature dependent thermodynamic properties of finite polymer chains without imposing a lattice. This leads to a new concept: the free energy theta temperature, T(theta)(F), at which the free energy is proportional to chain length. Above T(theta)(F), the polymer chain-solvent mixture leads to a single phase, whereas below T(theta)(F) the polymer solvent system has a positive surface tension with a tendency to phase separation to form a globular phase. For finite chains this coil-globule transition lies above the geometric theta temperature at which the distribution describes a Gaussian coil. CSAW provides the basis for a new approach to predict globular properties of real polymers.     

Ferrocene-containing polymers synthesized by acyclic diene metathesis (ADMET) polymerization

Herein we reported that ferrocene-containing polymers could be synthesized via acyclic diene metathesis(ADMET) polymerization of ferrocene-containing bis-styryl monomers. The all-trans-configured vinylene bonds of stilbene segment were proven by means of 13C-NMR, 1H-NMR, MALDI-TOF mass spectrometry and FTIR. Poly(1) showed maxima for absorption at 320 nm and emission at 430 nm which are structurally very similar to trans-stilbene, but 24 and 16 nm red shifted respectively. CIE chromaticity diagram shows that emission color could be adjusted by controlling the molecular weight. The polymer showed excellent solubility in common organic solvents and good thermal stability evidenced by TGA and DSC. The results of CV suggested the polymer possessed noninteracting metal centers which was confirmed by a reversible one-electron redox wave observed for the polymer.     

Development and validation of an SPE methodology combined with LC-MS/MS for the determination of four ionophores in aqueous environmental matrices

A multi-residue analytical methodology has been established for the determination of the four ionophores: lasalocid, monensin, salinomycin and narasin in aqueous environmental matrices, using nigericin as internal standard. The samples were filtrated prior to solid phase extraction. All compounds were measured using liquid chromatography coupled to tandem mass spectrometry applying electro spray ionisation. The absolute recoveries ranged from 92 to 110% (relative standard deviation: 2–14%) for spiked river water. The final method allowed for detection of ionophores down to a few ng/L in natural water bodies with LOQs for the entire methodology being 40, 49, 67, and 14 ng/L for lasalocid, monensin, salinomycin, and narasin, respectively.