Mechanochemistry of the 5f-element compounds

The effect of the mechanoactivation on UO₃ and U₃O₈ in agate or stainless steel vessels in air or in toluene is studied. UO₂(OH)₂ is the main product of UO₃·H₂O activation in steel vessel in air. The presence of toluene leads to strong amorphization and dispersity increase and, probably, to the formation of U₂O₅. The activation of U₃O₈ leads to its reduction to U₃O₇ which relative content in the reaction mixture depends on the mechanoactivation conditions.     

Reduction of U<Subscript>3</Subscript>O<Subscript>8</Subscript> to U by a metallic reductant,Li

Reduction of U₃O₈ was investigated for the recycling of spent oxide fuel from a commercial nuclear power plant. The possible reduction methods were proposed and compared. Based on the thermodynamic analysis, Li metal was selected as a reductant. The optimum reaction temperature for the reduction of U₃O₈ was investigated at the wider reaction temperature range. The adverse oxidation of U metal by Li₂O at 1,000 °C was experimentally verified. Ellingham diagram was constructed to investigate the extent of the uranium oxides reduction when the reaction was carried out above melting point of U metal.     

Effect of the mechanochemical treatment of a V<Subscript>2</Subscript>O<Subscript>5</Subscript>/MoO<Subscript>3</Subscript> oxide mixture on its properties

The mechanochemical treatment of a V₂O₅/MoO₃ oxide mixture (V/Mo = 70/30 at %) was performed in planetary and vibratory mills under varying treatment times and media. The resulting samples were characterized using XRD analysis, micro-Raman spectroscopy, and XPS; their specific surface areas and catalytic activities in n-butane and benzene oxidation reactions were determined. It was found that the treatment of the oxide mixture in water resulted in chaotic degradation of the parent oxides, a decrease in crystallite sizes, and an increase in the specific surface area at a sufficiently uniform oxide distribution over the sample. The treatment in ethanol was accompanied by an anisotropic deformation of the V₂O₅ crystal by layer sliding in parallel to the vanadyl plane (010) and a chaotic degradation of MoO₃ crystals. This process was accompanied by the partial nonuniform supporting of vanadium oxide crystals onto the surface of molybdenum oxide to increase the V/Mo ratio on the sample surface. In this case, the particle size of oxides decreased and the specific surface areas of samples increased. It was found that the treatment of the oxide mixture in air (dry treatment) resulted in the most significant decrease in the sizes of V₂O₅ and MoO₃ crystals and a growth in the specific surface area. The amorphization of the parent oxides and the formation of MoV₂O₈ were observed as the treatment time was increased; in this case, an excess of amorphous vanadium oxide was supported onto the surface of this compound. It was found that, in all types of mechanochemical treatment, the binding energies of the core electrons of vanadium and molybdenum remained almost unchanged to indicate the constancy of the oxidation states of these elements. Mechanochemical treatment resulted in an increase in the activity of the samples in n-butane and benzene oxidation reactions and in an increase in the selectivity of maleic anhydride formation. In this case, an increase in the specific catalytic activity of the samples correlated with a decrease in the crystallite size of vanadium oxide, whereas selectivity correlated with an increase in the relative concentration of the V₂O₅ plane (010). In these reactions, samples after dry treatment exhibited a maximum activity, which can be related to the formation of MoV₂O₈.     

Extraction of pertechnetates from HNO<Subscript>3</Subscript> solutions into ionic liquids

The effect of the oxidation temperature of sintered UO₂ pellets on the powder properties of U₃O₈ was studied in the temperature range 250–900 °C in air. The U₃O₈ was obtained at 450 °C after 180 min and its particle size and surface area are respectively, 35 µm and 0.7 m²/g. The reduction of the U₃O₈ powder resulted in UO₂ after 30 min with a surface area of 0.8 m²/g. This value was improved more than 3.5 times by applying five alternating oxidation–reduction cycles.     

The Microstructure of Cobalt Silica Gel Catalyst in the Presence of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Additive

The physico-chemical characteristics and microstructure of cobalt silica gel catalysts with an Al₂O₃ additive (up to 10%) for the synthesis of hydrocarbons by the Fischer–Tropsch method are studied using a set of methods including X-ray diffraction, BET, IR spectroscopy, and temperature-programmed reduction of H₂, as well as scanning and transmission electron microscopy. Phases with a spinel structure, Со₃О₄, CoAl₂O₄, and solid solutions on their basis are identified in the samples. The addition of Al₂O₃ changes the degree of heterogeneity and the orientation of the cobalt crystallites in the oxide and reduced forms of the catalysts. Addition of 1% Al₂O₃ stabilizes Со₃О₄ in the spinel form with a structure close to the normal one and promotes the formation of cobalt with a unimodal distribution of particles with an average size of 8 nm. The catalyst is characterized by maximum activity and selectivity with respect to C⁵⁺ carbons.     

Physical chemistry of rubidium uranomolybdates in the Rb<Subscript>2</Subscript>O-UO<Subscript>3</Subscript>-MoO<Subscript>3</Subscript> system

Rubidium uranomolybdates Rb₂UMo₂O₁₀ · 3H₂O, Rb₂UMo₂O₁₀, Rb₆UMo₄O₁₈, Rb₆U₂Mo₄O₂₁, Rb₂U₂MoO₁₀, Rb₂U₂Mo₃O₁₆, and Rb₂U₆Mo₇O₄₀ · 2H₂O have been synthesized and characterized by reaction calorimetry. The calorimetric data have been used to calculate the standard enthalpies of formation for the these compounds.     

Adsorption of NO,NH<Subscript>3</Subscript> and H<Subscript>2</Subscript>O on V<Subscript>2</Subscript>O<Subscript>5</Subscript>/TiO<Subscript>2</Subscript> catalysts

The adsorption of small molecules NO, NH₃ and H₂O on V₂O₅/TiO₂ catalysts is studied with the semiempirical SCF MO method MSINDO as pre-stage for the selective catalytic reduction of NO. The mixed catalyst is represented by hydrogen-terminated cluster models. The local arrangement of the cluster atoms is in accordance with available experimental information. Partial relaxation of cluster atoms near the adsorption sites is taken into account. Calculated adsorption energies are compared with experimental literature data. Rapid convergence of computed properties with cluster size is observed. A possible reaction mechanism for the catalytic reduction of NO with NH₃ and O₂ is outlined.     

Effect of Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> addition on structure and magnetic properties of Ni<Subscript>0.5</Subscript>Zn<Subscript>0.5</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanofibers

Ni_0.5Zn_0.5Fe₂O₄ nanofibers with addition of 0–5 wt% Bi₂O₃ were synthesized by calcination of the electrospun polyvinylpyrrolidone/inorganic composite nanofibers at the temperature below the melting point of Bi₂O₃. The effects of Bi₂O₃ addition on the phase structure, morphology and magnetic properties of the nanofibers were investigated by means of X-ray diffraction, scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray spectroscopy, selected area electron diffraction and vibrating sample magnetometer. It is found that the nanofiber diameter, crystallite size and magnetic parameters can be effectively tuned by simply adjusting the amount of Bi₂O₃ addition. The average diameter of Ni_0.5Zn_0.5Fe₂O₄ nanofibers doped with different contents of Bi₂O₃ ranges from 40 to 63 nm and gradually decreases with increasing Bi₂O₃ content. The addition of Bi₂O₃ does not induce the phase change and all the samples are a single-phase spinel structure. The amorphous Bi₂O₃ tends to concentrate on the nanoparticle surface and/or grain boundary and can retard the particles motion as well as the grain growth, resulting in a considerable reduction in grain size compared to the pristine sample. The specific saturation magnetization and coercivity of the nanofibers gradually decrease with the increase of Bi₂O₃ amount. Such behaviors are explained on the basis of chemical composition, surface effect, domain structure and crystal anisotropy.     

Trimetallic NiMoW/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> hydrotreating catalyst based on H<Subscript>4</Subscript>SiMo<Subscript>3</Subscript>W<Subscript>9</Subscript>O<Subscript>40</Subscript> mixed heteropoly acid

Trimetallic NiMoW/Al₂O₃ catalyst was prepared using mixed H₄SiMo₃W₉O₄₀ heteropoly acid of Keggin structure and nickel citrate. Bimetallic NiMo/Al₂O₃ and NiW/Al₂O₃ catalysts based on H₄SiMo₁₂O₄₀ and H₄SiW₁₂O₄₀, respectively, were synthesized as reference samples. The use of mixed H₄SiMo₃W₉O₄₀ heteropoly acid as an oxide precursor allows the tungsten sulfidation degree and the degree of promotion of active phase particles to be increased. The hydrodesulfurization activity is enhanced as compared to NiW/Al₂O₃ catalyst. The synergistic enhancement of the activity of the NiMo₃W₉/Al₂O₃ catalyst relative to the bimetallic analogs is probably caused by formation of new mixed promoted active sites for direct desulfurization.     

Phase formation in the V<Subscript>2</Subscript>O<Subscript>5</Subscript>-Nb<Subscript>2</Subscript>O<Subscript>5</Subscript>-MoO<Subscript>3</Subscript> system

The solid-phase interaction in the V₂O₅-Nb₂O₅-MoO₃ system has been investigated, and the formation of a solid solution bounded by the compositions MoNb₂V₄O_{18 ? δ}, Mo₂NbV₅O_{21 ? δ}, Mo₂Nb₃V₃O_{21 ? δ}, and Mo₄Nb₉V₉O_{57 ? δ} has been found (δ is nonstoichiometry). In the V₂O₅?Nb₂O₅ system, the formation of three compounds is verified, namely, VNbO₅ (tetragonal structure), VNb₉O₂₅, and V₂Nb₂₃O_62.5. The first two compounds are isostructural and form a continuous solid solution with tetragonal symmetry. A new compound of the composition Mo₃NbVO_{14 ? δ} has been synthesized. This compound is isostructural to the Mo₃Nb₂O₁₄ compound described in the literature and forms a tetragonal solid solution with it. The phase equilibria in the V₂O₅-Nb₂O₅-MoO₃ system in the subsolidus region have been determined.     

Solid solutions in the MgO-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-Cr<Subscript>2</Subscript>O<Subscript>3</Subscript> system

Coexisting solid solutions with spinel and corundum structure were synthesized at 1773 K and two pressures, 1 bar and 25 kbar. Samples were analyzed by electron microprobe analysis and X-ray powder diffraction. Pressure and temperature were shown to affect the properties of the solid solutions in different ways. Pressure governs the composition of the defect spinel Mg_1−xAl₂O₄, and temperature changes the cation distribution between coexisting phases. This allows one to separate the effects of cation exchange and magnetic contribution to the heat capacity in thermodynamic modeling. The defect spinel itself can form only because γ-Al₂O₃ exists, polymorph with spinel structure.     

Resonant emission of UO<Subscript>2</Subscript>, U<Subscript>3</Subscript>O<Subscript>8</Subscript>, and UO<Subscript>2+<Emphasis Type="Italic">x</Emphasis></Subscript> valence electrons under SR excitation near the O<Subscript>4,5</Subscript>(U) absorption edge

The structure of the resonant electron emission (REE) spectra of UO₂ (REE appears under the excitation with synchrotron radiation near the O_4,5(U) absorption edge at ∼100 eV and ∼110 eV) is studied with regard to the X-ray O_4,5(U) absorption spectrum of UO₂ and a quantitative scheme of molecular orbitals based on the X-ray electron spectroscopy data and the results of a relativistic calculation of the electronic structure of UO₂. The structure of the REE spectra of U₃O₈ and UO_2+x is studied for comparison, and the effect of the uranium chemical environment in oxides on it is found. The appearance of such a structure reflects the processes of excitation and decay involving the U5d and electrons of the outer valence MOs (OVMOs, from 0 to ∼13 eV) and inner valence MOs (IVMOs, from ∼13 eV to ∼35 eV) of the studied oxides. It is noted that REE spectra show the partial density of states of U6p and U5f electrons. Based on the structure of REE spectra, it is revealed that U5f electrons directly participate (without losing the f nature) in the chemical bonding of uranium oxides and are delocalized within CMOs (in the middle of the band), which results in the enhancement of the intensity of the REE spectra of CMO electrons during resonances. The U6d electrons are found to be localized near the bottom of the outer valence band and are observed in the REE spectra of the studied oxides as a characteristic maximum at 10.8 eV. It is confirmed that U6p electrons are effectively involved in the formation of IVMOs, which leads to the appearance of the structure in the region of IVMO electron energies during resonances. This structure depends on the chemical environment of uranium in the considered oxides.     

<Superscript>63</Superscript>Cu and <Superscript>139</Superscript>La NMR and chemical bonding in anion-deficient perovskite LACu<Subscript>0.81</Subscript>Ni<Subscript>0.19</Subscript>O<Subscript>2.5+δ</Subscript>

The ⁶³Cu and ¹³⁹La NMR spectra of the low-(δ = 0.25) and high-temperature (δ = 0) phases of lanthanum cuprate LACu_0.81Ni_0.19O_2.5+δ have been obtained. Quantum chemical calculations of the electronic structure of the high-temperature phase have been performed. It is found that the observed metal-semiconductor phase transition is attended by changes in the degree of atomic ordering and in the character of electronic conductivity over certain types of “copper” centers.     

Mechanosorption of carbon dioxide by Ca- and Mg-containing silicates and alumosilicates. Sorption of CO<Subscript>2</Subscript> and structure-related chemical changes

The discovery of the unusual ability of Ca- and Mg-containing silicates in certain grinding regimes to absorb carbon dioxide from the environment in amounts comparable to the mass of the ground sample has stimulated interest in the study of mechanochemical effects. The range of objects for studying natural minerals, such as labradorite (CaAl₂Si₂O₈)_0.562(NaAlSi₃O₈)_0.438, oligoclase (CaAl₂Si₂O₈)_0.148(NaAlSi₃O₈)_0.852, diopside CaMgSi₂O₆, and akermanite Ca₂MgSi₂O₇, as well as synthetic minerals gehlenite Ca₂Al₂SiO₇ and wollastonite CaSiO₃, is expanded to develop the model of deep mechanosorption of CO₂ and to derive equations that allow the kinetic analysis of the absorption of carbon dioxide by silicates in the course of mechanochemical activation to be performed. Regularities revealed previously and analogies to the processes that occur upon the dissolution of carbon dioxide in silicate melts, are generalized. Data on the absorption of carbon dioxide by Ca- and Mgcontaining silicates and alumosilicates, depending on the duration of mechanochemical activation in an AGO-2 centrifugal planetary mill in the atmosphere of CO₂ at a pressure of 10⁵ Pa, are obtained. Based on the data of X-ray phase analysis and IR spectroscopy, structural chemical changes in minerals and the forms of carbon dioxide in mechanochemically activated samples are discussed. It is shown that the intense penetration of gas molecules in particle bulk and their “dissolution” in structurally disordered silicate matrix in the form of distorted CO ₃ ^2? ions occurs upon mechanosorption.     

Preparation and characterization of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>composite particles

Using Fe₃O₄ nano-particles as seeds, a new type of Fe₃O₄/Au composite particles with core/shell structure and diameter of about 170 nm was prepared by reduction of Au³⁺ with hydroxylamine in an aqueous solution. Particle size analyzer and transmission electron microscope were used to analyze the size distribution and microstructure of the particles in different conditions. The result showed that the magnetically responsive property and suspension stability of Fe₃O₄ seeds as well as reduction conditions of Au³⁺to Au⁰are the main factors which are crucial for obtaining a colloid of the Fe₃O₄/Au composite particles with uniform particle dispersion, excellent stability, homogeneity in particle sizes, and effective response to an external magnet in aqueous suspension solutions. UV-Vis analysis revealed that there is a characteristic peak of Fe₃O₄/Au fluid. For particles with d(0.5)=168 nm, the λmax is 625 nm.     

Phase formation in the V<Subscript>2</Subscript>O<Subscript>5</Subscript>-Ta<Subscript>2</Subscript>O<Subscript>5</Subscript>-MoO<Subscript>3</Subscript> system

Solid-phase interactions in the V₂O₅-Ta₂O₅-MoO₃ system were studied. The formation of com- pounds TaVO₅ and VTa₉O₂₅ in the V₂O₅-Ta₂O₅ binary system was verified. Tetragonal VTa₉O₂₅-base solid solutions of the general formula Ta_{5 + 4x} V_{5 − 4x} O₂₅ (x = 0.25–1) and TaVO₅-base solid solutions of the general formula Ta _x Mo_{1 − x} V_{2 − x} O_{8 − 3x} (x = 0.625–1) were found to form. Subsolidus phase equilibria in the V₂O₅-Ta₂O₅-MoO₃ were determined.     

Electrolytic production of metallic uranium from U3O8 in a 20-kg batch scale reactor</p> </p>

Summary The electrolytic reduction of U₃O₈ powder was carried out using LiCl-Li₂O molten salt in a 20-kg U₃O₈ batch cell to verify the feasibility of the process. As the current passes the cell, the decomposition of Li₂O and the reduction of U₃O₈ occur simultaneously in a cathode assembly and oxygen gas evolvs at the anode. The results from a 20-kg U₃O₈ scale cell were compared with data obtained from a bench scale cell. The results suggest a successful demonstration of this process, exhibiting a reduction conversion of U₃O₈ of more than 99% in a batch.</p> </p>     

Phase formation in the FeVO<Subscript>4</Subscript>–Co<Subscript>3</Subscript>V<Subscript>2</Subscript>O<Subscript>8</Subscript> system

Phase relations in the solid state in the FeVO₄–Co₃V₂O₈ system, in the whole range of components concentration have been studied. It was found that the composition of the phase of the howardevansite type structure, formed in the investigated system, corresponds with the Co_2.616Fe_4.256V₆O₂₄ formula. The phase of the lyonsite type structure has a homogeneity range with the Co_3+1.5xFe_4–xV₆O₂₄ formula (0.476 formula (0.476<x<1.667). The melting temperature and the volume of the unit cell of the lyonsite type structure phase increases together with the rise of cobalt quantity contained in it. Basing on the results of the DTA and XRD measurements a phase diagram of the FeVO_4–Co₃V₂O₈ system up to the solidus line was constructed.     

Interactions in the NdF<Subscript>3</Subscript>-Nd<Subscript>2</Subscript>O<Subscript>3</Subscript>-MF<Subscript>2</Subscript> (M = Ba,Sr) systems

Isothermal anneals (at 873 K) and powder X-ray diffraction were used to study isothermal sections of phase diagrams of the NdF₃-Nd₂O₃-MF₂ (M = Ba, Sr) systems. In studying the NdF₃-Nd₂O₃-BaF₂ system, classical solid-phase synthesis was supplemented with mechanochemical activation of feedstock mixtures or BaF₂ activated with gaseous hydrogen fluoride was used. In both systems, a solid solution with the fluorite structure based on MF₂ and NdOF phases, a solid solution with the tysonite structure based on NdF₃, and an ordered fluorite-related phase Ba₄Nd₃F₁₇ were found. The NdOF-based solid solutions were shown to have polymorphism: β_trig ai α_cub at ≈800 K; a new trigonal phase of these solid solutions has been discovered. The effect of a dimensional factor $\left( {R_{Ba^{2 + } } > R_{Sr^{2 + } } } \right)$\left( {R_{Ba^{2 + } } > R_{Sr^{2 + } } } \right) on phase formation and unit cell parameters of the solid solutions was traced.