Growth and spectral properties of Nd-doped Sr3Y(BO3)3 crystal

A new crystal of Nd³⁺:Sr₃Y(BO₃)₃ with dimension up to 25×35 mm² was grown by Czochralski method. Absorption and emission spectra of Nd³⁺: Sr₃Y(BO₃)₃ were investigated . The absorption band at 807 nm has a FWHM of 18 nm. The absorption and emission cross sections are 2.17×10⁻²⁰ cm² at 807 nm and 1.88×10⁻¹⁹ cm² at 1060 nm, respectively. The luminescence lifetime τ_f is 73 μs at room temperature     

Synthesis and characterization of a novel non-linear optical material La2SrB10O19

A novel compound with the chemical formula of La₂SrB₁₀O₁₉ has been successfully synthesized from the La₂O₃--- SrO---B₂O₃ system via a solid state reaction. The powder X-ray diffraction data is reported. It is found that the data show little difference from that of La₂CaB₁₀O₁₉ which demonstrate that they are isostructural. The powder second harmonic generation effect of La₂SrB₁₎O₁₉ is about twice that of KH₂PO₄(KDP). The investigation of crystal growth is in progress.     

Growth twins in self-frequency doubling laser crystal YbxY1−xAl3(BO3)4

Using chemical etching.method, the growth twins in self-frequency doubling laser crystal Yb_xY_1−xAl₃(BO₃₄ have been observed. The etching pits on both sides of growth twin boundaries in the (10 1) slice are of the triangles with different orientations. The structure of growth twins is investigated by transmission synchrotron topography. In the transmission synchrotron topograph, the growth twins are visible not by ‘domain contrast’ but by ‘boundary contrast’, i.e. the twins appear in the topograph in form of X-ray kinematical diffraction contrast due to the lattice strain stemming from the impurity incorporation in the boundaries. The growth twins in Yb_xY_1−xAl₃(BO₃)₄ crystal are of inversion types, since no domain contrast was observed.     

Vapor phase epitaxy of pure VO2 and V1−xCrxO2

The vapor phase epitaxy of thin epilayers of VO₂ and V_1−xCrxO₂ on TiO₂ transparent substrates is described. Chemical vapor deposition occurs by reacting a (VOCL₃/CrO₂Cl₂/H₂O/H₂) mixture at about 800°C using argon as a carrier gas. The preparation of pure VO₂ requires special care to make it homogeneously stoichiometric and to obtain steep concentration profiles at the TiO₂/VO₂ interface. Layers were obtained which had electrical and optical properties comparable to the best bulk crystals grown by other techniques. Homogeneous solid solutions of V_1−xCr_xO₂ epilayers were also grown for the first time in the range o < x < 0.17. Chromium concentration and homogeneity were determined by electron microprobe analysis. The separation coefficient k was also found to vary with x. It is close to unity below x = 0.001 and above this value Cr is incorporated more easily. High quality heteroepitaxial layers (1 cm² area, 1 to 30 μm thickness) of V_1−xCr_xO₂ have for the first time allowed the measurement of the optical absorption coefficient.     

Ion exchange in KTiOPO4 crystals by electrolysis

A novel ion exchange technique is introduced in this paper. By electrolyzing a RbNO₃ solution held in two electrolyzers separated by a KTP crystal under the applied electric field, a Rb_1−xK_xTiOPO₄ layer formed This was confirmed by electron probe microanalysis. The distribution of Rb⁺ in the KTP crystal was measured by electron probe X-ray line scanning. This technique is expected to have potential applications in waveguide fabrications.     

Growth and spectral properties of Nd:LaVO4 crystal

This paper reports the growth and spectral properties of 3.5 at% Nd³⁺:LaVO₄ crystal with diameter of 20×15 mm² which has been grown by the Czochralski method. The spectral parameters were calculated based on Judd–Ofelt theory. The intensity parameters Ω_λ are: Ω₂=2.102×10⁻²⁰ cm², Ω₄=3.871×10⁻²⁰ cm², Ω₆=3.235×10⁻²⁰ cm². The radiative lifetime τ_r is 209 μs and calculated fluorescence branch ratios are: β₁(0.88μm)=45.2, β₂(1.06μm)=46.7, β₃(1.34μm)=8.1. The measured fluorescence lifetime τ_f is 137 μm and the quantum efficiency η is 65.6%. The absorption band at 808 nm wavelength has an FWHM of 20 nm. The absorption and emission cross sections are 3×10⁻²⁰ and 6.13×10⁻²⁰ cm², respectively.     

Growth and properties of (Pb0.90La0.10)TiO3 thick films prepared by RF magnetron sputtering with a PbO buffer layer

The (Pb_0.90La_0.10)TiO₃ [PLT] thick films (3.0 μm) with a PbO buffer layer were deposited on the Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) substrates by RF magnetron sputtering method. The PLT thick films comprise five periodicities, the layer thicknesses of (Pb_0.90La_0.10)TiO₃ and PbO in one periodicity are fixed. The PbO buffer layer improves the phase purity and electrical properties of the PLT thick films. The microstructure and electrical properties of the PLT thick films with a PbO buffer layer were studied. The PLT thick films with a PbO buffer layer possess good electrical properties with the remnant polarization (P_r=2.40 μC cm⁻²), coercive field (E_c=18.2 kV cm⁻¹), dielectric constant (ε_r=139) and dielectric loss (tan δ=0.0206) at 1 kHz, and pyroelectric coefficient (9.20×10⁻⁹ C cm⁻² K⁻¹). The result shows the PLT thick film with a PbO buffer layer is a good candidate for pyroelectric detector.     

New solvents for the growth of substituted BaFe12O19 single crystals from high-temperature solutions

The solubility of a series of hexaferrite derivatives of BaFe₁₂O₁₉ in solvents of the system Na₂O-B₂O₃ with oxide ratios of 7:3 and 3:2 has been investigated. The temperature dependences of the saturation concentration in these solvents are determined for ferrites with the nominal compositions Ba_0.8Pb_0.2Fe₁₂O₁₉, BaFe₁₀Ga₂O₁₉, BaFe₁₀Al₂O₁₉ and BaFe₈Mn₂ Ti₂O₁₉. Single crystals of BaFe₁₂O₁₉, in which part of the metal ions are replaced by various amounts of Pb²⁺, Ga³⁺, Al³⁺ and Mn²⁺ + Ti⁴⁺ ions, are g rown from the solutions by the slow cooling technique. The distribution coefficients of the substituting ions and the compositions of the crystals obtained are established by microprobe analysis (EPMA). Information on the position of substitution is obtained from the Mössbauer spectra.     

B NMR investigations in xV2O5–B2O3 and xV2O5–B2O3–PbO glasses

11B (I=3/2) MAS NMR in the binary glass system xV₂O₅–B₂O₃ (x=0.053, 0.43) and the ternary glass system xV₂O₅–B₂O₃–PbO (0.1x1.5) has been investigated at room temperature. In the xV₂O₅–B₂O₃ glasses, one NMR line due to BO₃ unit was observed. Meanwhile in the xV₂O₅–B₂O₃–PbO, two NMR lines which arise from BO₃ and BO₄ units were detected, where the appearance of BO₄ units is produced by the presence of PbO. From the computer-simulation of the ¹¹B NMR central transition line (m=−1/2↔1/2), the quadrupole parameters (e²qQ/h and η) for BO₃ units in xV₂O₅–B₂O₃, and those for BO₃ and BO₄ units in xV₂O₅–B₂O₃–PbO were obtained as a function of x. As the V₂O₅ content increases in xV₂O₅–B₂O₃–PbO, the e²qQ/h and η values of the BO₃⁻ associated resonance are found to slightly decrease and increase, respectively. Meanwhile, the e²qQ/h and η values of BO₄⁻ associated resonance in xV₂O₅–B₂O₃–PbO are found to slightly increase and decrease, respectively. By comparing the intensities of the total transitions (m=−3/2↔−1/2,m=−1/2↔1/2, and 1/2↔3/2) for the ¹¹B NMR line of BO₃ and BO₄ units contained in xV₂O₅–B₂O₃–PbO with those of respective standard samples of 0.053V₂O₅–B₂O₃ and NaBH₄, the quantitative fractions of BO₃ and BO₄ in xV₂O₅–B₂O₃–PbO were obtained as a function of x.     

Synthesis, growth and characterization of a new laser upconversion crystal Ba2ErCl7

A modified method to synthesize the new laser upconversion material Ba₂ErCl₇ using Er₂O₃, BaCl₂ 2H₂O and NH₄CI is reported for the first time in this paper. Single crystals up to 5–8mm in diameter and 10–20 mm in length have been grown by Czochralski method. The transmittance spectra of Ba₂ErCl₇ single crystal has first been measured by using an HITACHI U-3500 spectrophotometer. There are three intense absorption peaks ⁴I_9/2⁴I_11/2 and ⁴I_13/2 in the infrared range which can be excited by 803nm, 980nm and 1.5μm laser diodes (LDs), respectively. The cut-off wavelength of the crystal is 230mn. Intense green luminescence can be observed when the crystal is pumped by a ED at 803nm. The formation of the defects is also discussed.     

Mössbauer studies on some glasses and crystals in the Na2O---Fe2O3---SiO2 system

Mössbauer absorption measurements have been made at room temperature on ⁵⁷Fe in iron sodium silicate glasses containing 3–15 mol% Fe₂O₃ and various iron alkali silicate crystals in order to study the state of iron in these glasses. The spectra of all the glasses gave one doublet with a quadrupole splitting varying from 0.73–0.78 mm s⁻¹, while those of Na₂O · Fe₂O₃ · 4 SiO₂ and 5 Na₂O · Fe₂O₃ · 8 SiO₂ crystals showed much smaller quadrupole splitting, 0.28 mm s⁻¹ and 0.10 mm s⁻¹, respectively, and an asymmetrical doublet of much narrower linewidth. When sodium was replaced by other alkali metals of larger size, such as K and Cs, in MFeSi₂O₆ and MFeSi₃O₈ crystals, the quadrupole splitting became wider and approached to 0.73 mm s⁻¹. Such a variation was not observed for glasses. These results suggest that a larger number of non-identical sites exist in iron sodium silicate glasses than in the corresponding crystals.     

The effect of mixed alkaline earths on the diffusivity and the incorporation of iron in 5Na2O · xMgO · (15−x)CaO · yAl2O3 · (80−y)SiO2 melts

Diffusion coefficients of iron were measured in glass melts with the basic compositions 5Na₂O · xMgO · (15−x)CaO · yAl₂O₃ · (80−y)SiO₂ with x=5, 10 and y=0, 5, 7.5, 10 and 15. The melts were doped with 0.25 mol% Fe₂O₃ and studied in the temperature range from 1000 to 1600 °C using square-wave voltammetry. The voltammograms exhibited distinct peaks attributed to the reduction of Fe³⁺ to Fe²⁺, from which peak currents mixed diffusion coefficients of iron were calculated. Diffusion coefficients in all melt compositions which did not show crystallization could be fitted to Arrhenius equation. The diffusivities measured in different melt compositions were related to the same viscosity, i.e. not the same temperature. Increasing the alumina concentration from 5 to 10 mol% resulted in an increase of the viscosity corrected diffusivities. At further increasing alumina concentrations, the diffusivities get smaller again. This can be explained by the stabilizing effect of Na⁺ and Ca²⁺ on FeO⁻₄ and AlO⁻₄-tetrahedra, which strengthens the incorporation of Fe³⁺ into the glass structure.     

Viscosity and IR investigations in the Li2O---B2O3 system

The high viscosity in melts of the Li₂O---B₂O₃ system makes it very difficult to grow large crystals of lithium triborate. The viscosity and IR characteristics of molten li₂O---B₂O₃ system are reported in this paper. When the temperature increases the viscosity of li₂O---B₂O₃ system decreases and follows an Arrhenius-type relationship. With an increasing 13203 ratio in Li₂O---B₂O₃ melts, the viscosity rises gradually to a maximum with a composition Li₂O: 3.513203 then it falls rapidly. In order to find active agents to reduce the viscosity, Na₂O, NaCl, LiF, P205, M003, W03 etc oxides were added to Li₂O---B₂O₃ samples respectively and investigated using the orthogonal method. The experimental results show that the addition of acidic oxides can significantly decrease the viscosity in the Li₂O---B₂O₃ system. For Li₂O: 4.513203, an ideal additive agent is 20wt% Li₂O:: 2MoO₃. Near the composition for crystal growth, the percentage reduction of viscosity is 62.2%. The IR spectra of Li₂O---B₂O₃ system revealed that the BO₄⁻/NO₃⁻ ratio is reduced in the melt using Li₂O: 2MoO₃ as an additive. It is proposed that the M003 reduced the concentration of bridging oxygen atoms of BO₄⁻. The change of structure explains the decline in the viscosity. In the crystal structures of lithium triborate, the matrix spaces are so small that larger other cations than Li+ are very difficult to enter the crystal matrix. So the use of additive agents to reduce the viscosity is a possible method if no new phase appears.     

The effect of MgO on the thermodynamics of the Fe/Fe-redox equilibrium and the incorporation of iron in soda-magnesia-aluminosilicate melts

Melts with the basic compositions 10Na₂O · 10MgO · xAl₂O₃ · (80−x)SiO₂ (x=0, 5, 10, 15 and 20), 10Na₂O · xMgO · 10Al₂O₃ · (80−x)SiO₂ (x=5, 10, 15 and 20) and xNa₂O · 10MgO · 10Al₂O₃ · (80−x)SiO₂ (x=5, 10 and 15) all doped with 0.25 mol% Fe₂O₃ were studied using square-wave voltammetry. The temperatures applied were in the range of 1000–1600 °C. The square-wave voltammograms recorded show peaks caused by the reduction of Fe³⁺ to Fe²⁺. The attributed peak potentials measured decreased linearly with decreasing temperatures. Increasing the MgO-concentration led to more negative peak potentials. Introducing alumina in the melt first resulted in less negative peak potentials. If the molar Al₂O₃-concentration is equal to that of Na₂O (=10 mol%) the peak potentials are least negative. Further increase of the Al₂O₃-concentration led to more negative peak potentials. The variation of the Na₂O-concentration led to a maximum in the peak potentials at an Na₂O-concentration of 10 mol%. An empirical formula which allows the calculation of standard potentials from the chemical composition is proposed. Furthermore, a structural explanation for the effect of the chemical composition is given. Especially, the incorporation of Al₂O₃ as AlO₄⁻-tetrahedra at [Al₂O₃] < [Na₂O] and as network modifier at larger concentrations was structurally explained by the similarities of Fe²⁺ and Mg²⁺, with respect to cation radii and metal–oxygen bond lengths.     

Li conductivity in lithium niobate: silica glasses

Glasses of composition 65 mol% LiNbO₃:: 35 mol% SiO₂ have been shown to be Li⁺ ion conductors with a conductivity at 200°C > 1 × 10⁻⁵ (η cm)⁻¹ and an activation energy of 0.54 eV. The addition of approximately 0.1 mol% Fe₂O₃ leads to an enhancement of conductivity to ≈10⁻³ (η cm)⁻¹ at 200°C and an activation energy of 0.67 eV. The effect of Fe is shown to be in the control of microstructure in the glass, with Fe₂O₃ concentrations < 1 mol% acting as a grain growth inhibitors and larger concentrations acting as a nucleating agents. A model for this process based on the expected stoichiometry of the melt and the effect of Fe²⁺ and Fe³⁺ in charge compensation is in excellent agreement with experimental data from electron spin resonance.     

Electronic traps in mixed Si1−xGexO2 films

Thermally stimulated luminescence (TSL) and infrared (IR) spectroscopy were measured in plasma grown Si_1−xGe_xO₂ (x=0, 0.08, 0.15, 0.25, 0.5) with different thicknesses (12–40 nm). A comparison with the TSL properties of thermally grown SiO₂ and GeO₂ was also performed. A main IR absorption structure was detected, due to the superposition of the peaks related to the asymmetric O stretching modes of (i) Si–O–Si (at ≈1060 cm⁻¹) and (ii) Si–O–Ge (at 1001 cm⁻¹). Another peak at ≈860 cm⁻¹ was observed only for Ge concentrations, x>0.15, corresponding to the asymmetric O stretching mode in Ge–O–Ge bonds. A TSL peak was observed at 70°C, and a smaller structure at around 200°C. The 70°C peak was more intense in all Ge rich layers than in plasma grown SiO₂. Based on the thickness dependence of the signal intensity we propose that at Ge concentrations 0.25x0.5 TSL active defects are localised at interfacial regions (oxide/semiconductor, Ge poor/Ge rich internal interface, oxide external surface/atmosphere). Based on similarities between TSL glow curves in plasma grown Si_1−xGe_xO₂, thermally grown GeO₂ and SiO₂ we propose that oxygen vacancy related defects are trapping states in Si_1−xGe_xO₂ and GeO₂.     

Synthesis of Y2O3:Eu phosphors by bicontinuous cubic phase process

A novel approach for preparation of red-emitting europium-doped yttrium oxide phosphor (Y₂O₃:Eu) by using the bicontinuous cubic phase (BCP) process was reported in this paper. The BCP system was composed of anionic surfactant sodium bis(2-ethylhexyl)sulfosuccinate (AOT) and aqueous yttrium nitrate/europium nitrate solution. Energy dispersive spectrometer analysis revealed the homogeneous precipitation occurred in the BCP structure. Thermogravimetric analysis measurements indicated the precursor powder was europium-doped yttrium hydroxide, Y_1−xEu_x(OH)₃. Scanning electron microscopy micrographs showed the precursor powder had a primary size about 30 nm and narrow size distribution. After heat treatment in furnace above 700 °C for 4 h, high crystallinity Y₂O₃:Eu phosphors was obtained. However, the primary size of particles grew to 50–200 nm and the dense agglomerates with a size below 1 μm were formed. X-ray diffraction patterns indicated the crystal structure of precursor powders and Y₂O₃:Eu phosphors were amorphous and body-centered cubic structure, respectively. The photoluminescence analysis showed that the obtained Y₂O₃:Eu phosphor had a strong red emitting at 612 nm and the quenching started at a Eu concentration of 10 mol%. This study indicated that the BCP process could be used to prepare the highly efficient oxide-based phosphors.     

Study of electrical properties of MoO3–Fe2O3–P2O5 and SrO–Fe2O3–P2O5 glasses by impedance spectroscopy. II

The electrical and dielectric properties for three series of MoO₃–Fe₂O₃–P₂O₅ and one series of SrO–Fe₂O₃–P₂O₅ glasses were measured by impedance spectroscopy in the frequency range from 0.01 Hz to 3 MHz and over the temperature range from 303 to 473 K. It was shown in Part I that the MoO₃ is incorporated into phosphate network and the structure/properties are strongly influenced by the overall O/P ratio. The Fe₂O₃ content and Fe(II)/Fe_tot ratio in these glasses have significant effects on the electrical conductivity and dielectric permittivity. With decreasing Fe₂O₃ content in MoO₃–Fe₂O₃–P₂O₅ glasses with O/P at 3.5 the dc conductivity, σ_dc(ω) decreases for two orders of magnitude, which indicates that the conductivity for these glasses depends on Fe₂O₃ and is independent of the MoO₃ content. Also, the dielectric properties such as ^′(ω), ^″(ω) and σ_ac(ω) and their variation with frequency and temperature indicates a decrease in relaxation intensity with increase in the concentration of MoO₃. On the other hand, the dc conductivity for MoO₃–Fe₂O₃–P₂O₅ glasses with O/P > 3.5 increases with the substitution of MoO₃ which has been explained by an increase in the number of non-bridging oxygens and formation of Fe–O–P bonds that are responsible for formation of small polarons. The increase in the dielectric permittivity, ^′(ω) with increasing MoO₃ content is attributed to the increase in the deformation of glass network with increasing bonding defects. For SrO–Fe₂O₃–P₂O₅ glasses the conductivity and dielectric permittivity remained constant with increasing SrO.     

Improved growth of PbI2 single crystals

The phase equilibrium and the crystallization process of lead iodide (PbI₂) melt have been primarily investigated according to the lead–iodine phase diagram. It is found that the iodine evaporation and the segregated lead deposition are the two important factors that affect the PbI₂ crystal quality. The new method of Pulling U-type quartz growth ampoule has been made to impede the decomposition of PbI₂ and the vaporization and condensation of iodine. An orange and translucent PbI₂ single crystal of large size was obtained by the improved growth method, i.e. U-type ampoule pulling. Resistivity of the as-grown crystal is up to 4×10¹¹ Ω cm, and IR transmission is up to 45% in the region from 7800 to 450 cm⁻¹. Therefore, the improved growth method is a promising convenient new method for the growth of high quality PbI₂ crystals.     

The effect of hydrostatic pressure on the dielectric constants, and their temperature dependences, of phosphate and tellurite glasses

Measurements of the pressure dependence of the static dielectric constant of tellurite (pure TeO₂ and 67%TeO₂ + 33%WO₃) and samarium phosphate (5%Sm₂O₃ + 95%P₂O₅ and 15%Sm₂O₃ + 85%P₂O₅) glasses at elevated pressures (0–70 kbar) for a range of temperatures (77–380 K) are reported. The electrical properties under pressure have been determined from the low-frequency complex plane analysis of glass discs contained within a Bridgman opposed anvil cell. The most notable observation is that the pressure dependence of the static dielectric constant, of all glasses studied, is positive, for example for vitreous TeO₂ ln ε/P is equal to 4.41 × 10⁻¹¹ (Pa⁻¹) at 293 K. Behaviour of this type is common to a number of materials (plastics and chalcogenide glasses) for which it is not possible to define any long-range order. It is in direct contrast with the behaviour of crystalline insulators, for which ε/P is usually negative. The effect of pressure on the dielectric constant has been analysed using two different approaches based on the macroscopic Clausius-Mossotti equation. The effects of high pressure on the dielectric constant have been correlated with the temperature dependence of the dielectric constant at atmospheric pressure.