Electrotransport properties of ions in aqueous solutions of H<Subscript>2</Subscript>SeO<Subscript>4</Subscript> and Na<Subscript>2</Subscript>SeO<Subscript>4</Subscript>

Coefficients of self-diffusion, absolute speeds of movement of ions and the activation energy of electrical conductivity are found from the conductance measurements of aqueous solutions of selenic acid and sodium selenate at different concentrations in a temperature range of 288–318 K. Both the Stokes and effective radii of ions and their hydrate numbers at 298 K are calculated. The obtained results are interpreted in the frames of Samoilov theory on positive and negative hydration of ions.     

Copper hexacyanoferrate multilayer films on glassy carbon electrode modified with 4-aminobenzoic acid in aqueous solution

4-Aminobenzoic acid (4-ABA) was covalently grafted on a glassy carbon electrode (GCE) by amine cation radical formation during the electrooxidation process in 0.1 M KCl aqueous solution. X-ray photoelectron spectroscopy (XPS) measurement proves the presence of 4-carboxylphenylamine on the GCE. Electron transfer processes of Fe(CN)₆³⁻ in solutions of various pHs at the modified electrode are studied by both cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Changing the solution pH would result in the variation of the terminal group's charge state, based on which the surface pK_a values were estimated. The copper hexacyanoferrate (CuHCF) multilayer films were formed on 4-ABA/GCE prepared in aqueous solution, and which exhibit good electrochemical behavior with high stability.     

The processes involved in the Se electrodeposition and dissolution on Au electrode: the H<Subscript>2</Subscript>Se formation

The processes involved in the Se electrodeposition, mainly the one related to the formation of H₂Se species on Au electrode in perchloric acid solutions, have been investigated through cyclic voltammetry, electrochemical quartz crystal microbalance (EQCM), rotating ring-disc electrode (RRDE), and atomic force microscopy (AFM) techniques. In the experiments performed with the EQCM, with the potential sweep in the negative direction, the responses for the mass variation were divided in three well-defined potential regions: A (from 1.55 to 0.35 V), B (from 0.35 to −0.37 V), and C (from −0.37 to −0.49 V). It was verified that the following processes can occur, respectively: the species (AuO)₂H₂SeO₃ was desorbed during the AuO reduction, the reduction of Se(IV) to Se(0), and the formation of H₂Se. When the potential was swept in the positive direction, the responses for the mass variation were divided in four well-defined potential regions: D (from −0.49 to 0.66 V), E (from 0.66 to 0.99 V), F (from 0.99 to 1.26 V), and G (from 1.26 to 1.55 V), and the described processes in these regions were, respectively: the Se deposition and adsorption of water molecules and/or perchlorate ions, the Se dissolution, the Se incorporating mass in the form of HO–Se, and the Au oxidation (all potentials are referred to the Ag/AgCl electrode). Making use of the RRDE, using the collection technique, the formation of H₂Se species during the Se electrodeposition was investigated. Therefore, it was confirmed that this species is formed on the disc electrode between −0.3 and −0.55 V vs the Ag/AgCl potential range (collecting the oxidized compound onto the ring electrode). AFM images also indicated that the surface topography of the Se-massive deposit on Au is different from the images registered after the formation of H₂Se species, confirming the cathodic stripping of Se.     

Deposition of Prussian blue on nanoporous gold film electrode and its electrocatalytic reduction of H<Subscript>2</Subscript>O<Subscript>2</Subscript>

Prussian blue-modified nanoporous gold film (PB-NPGF) electrode was fabricated in this study. The fabrication was realized through electrodeposition of Prussian blue nanoparticles on the skeleton of a nanoporous gold film electrode without destroying the porous structure of NPGF electrode. The resulting PB-NPGF composite electrode showed very high electrocatalytic activity, repeatability, and stability to the reduction of H₂O₂. For instance, its activity was about twenty times that of the PB-modified polished gold electrode. More importantly, the sensitivity of the PB-NPGF composite electrode reaches as high as 10.6 μA μM⁻¹ cm⁻². This PB-NPGF composite electrode is very promising in the fields of catalysis, analysis, and so on.     

Nucleation and growth of Cu onto polycrystalline Pt electrode from acidic CuSO4 solution in the presence of H2SeO3

The early stages of Cu electrodeposition onto Pt(poly) have been investigated in 0.5 M H₂SO₄ + 0.01 M CuSO₄ solution without or with H₂SeO₃ when a molar concentration ratio [Cu(II)]/[Se(IV)] ≥ 2×10² using electrochemical and ex situ AFM techniques. The overpotential deposition of Cu has been performed onto a Pt surface precovered independently with Cu in amount close to an equivalent monolayer. Chronoamperometric results have been shown to follow an instantaneous 3D nucleation and diffusion-controlled growth model. The values of diffusion coefficient D for Cu²⁺, number of nuclei N and average nuclei radius r _av have been calculated. In the local regions of the surface, the separate large agglomerates composed of the different diameter clusters have been revealed in both cases, but, in the presence of the H₂SeO₃, they attained a distinct chain-like configuration. Some morphological characteristics have been reported.     

Electrochemical Behavior of Cobalt-Dimethylglyoxime Complex Co(DMG)<Subscript>2</Subscript>(H<Subscript>2</Subscript>O)<Subscript>2</Subscript> in the Carbon Dioxide Reduction Process

The electrochemical behavior of a complex of cobalt with dimethylglyoxime Co(DMG)₂(H₂O)₂ is studied by cyclic voltametry. Peaks corresponding to redox transitions Co(III)/Co(II) and Co(II)/Co(I) are observed in the potential region 0.4 to ?1.8 V (Ag/AgCl). The product of reduction of the initial complex interacts with carbon dioxide to form a stable compound, probably an intermediate product of electrocatalytic reduction of CO₂ to CO in the presence of N₄-macrocyclic complexes of cobalt.     

槲皮素在聚谷氨酸修饰玻碳电极上的伏安行为及检测

制备了聚谷氨酸修饰玻碳电极,通过循环伏安法和差分脉冲伏安法研究了槲皮素在该修饰电极上的电化学行为。在pH 5.00的B-R缓冲液中,槲皮素在修饰电极上于0.28 V(vs Ag/AgCl)电位处产生一个灵敏的DPV阳极氧化峰,氧化峰电流与槲皮素的浓度在1.0×10-8～5×10-5 mol/L的范围内呈良好的线性关系,最低检测限为4.0×10-9 mol/L。实验表明,聚谷氨酸修饰电极可提高槲皮素的检测灵敏度,该电极用于芦丁水解产物中槲皮素的检测,回收率为103.4%～104.5%。     

Kinetics of the oxidation of diethyl sulfide in the B(OH)<Subscript>3</Subscript>-H<Subscript>2</Subscript>O<Subscript>2</Subscript>/H<Subscript>2</Subscript>O system

Data obtained for the kinetics of oxidation of diethyl sulfide (Et₂S) by hydrogen peroxide in aqueous solution catalyzed by boric acid indicate that monoperoxoborates B(O₂H)(OH) ₃ ⁻ and diperoxoborates B(O₂H)₂(OH) ₂ ⁻ are the active species. The rates of the reactions of Et₂S with B(O₂H)(OH) ₃ ⁻ and B(O₂H)₂(OH) ₂ ⁻ are 2.5 and 100 times greater than with H₂O₂. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 43, No. 1, pp. 38–42, January–February, 2007.     

pH-sensing properties of PbO<Subscript>2</Subscript> thin film electrodeposited on carbon ceramic electrode

In this paper, a new highly sensitive potentiometric pH electrode is proposed based on the solid-state PbO₂ film electrodeposited on carbon ceramic electrode (CCE). Two different crystal structures of PbO₂, α and β were examined and the similar results were obtained. Moreover, the experimental results obtained for the proposed pH sensor and a conventional glass pH electrode were in good agreement. The electromotive force (emf) signal between the pH-sensitive PbO₂-coated CCE and SCE reference electrode was linear over the pH range of 1.5–12.5. Near-Nernstian slopes of −64.82 and −57.85 mV/pH unit were obtained for α- and β-PbO₂ electrodes, respectively. The interferences of some mono-valence and multi-valence ions on potentiometric response of the sensor were studied. The proposed pH sensor displayed high ion selectivity with respect to K⁺, Na⁺, Ca²⁺, and Li⁺, with log values around −12 and has a working lifetime of about 30 days. Key parameters important for the pH sensor performance, including kind of PbO₂ film, selectivity, response time, stability, and reproducibility, have been characterized. The proposed electrode showed a good efficiency for direct pH-metry after calibration and pH-metric titrations without calibration step. The response time was about 1 s in acidic medium and less than 30 s in alkaline solutions. The pH values of complex matrix samples such as fruit juices measured by the proposed sensor and a conventional glass pH electrode were in good agreement.     

Deposition of Cu on a polycrystalline Pt-electrode at potentials more positive than the equilibrium potential from CuSO<Subscript>4</Subscript> solutions of various acidities in the presence of H<Subscript>2</Subscript>SeO<Subscript>3</Subscript>

Undervoltage deposition of copper adatom layers on Pt was studied in acid CuSO₄ solutions at various pH values with or without addition of H₂SeO₃.     

Kinetics of processes occurring at a H<Subscript>3</Subscript>PW<Subscript>12</Subscript>O<Subscript>40</Subscript>/Pt,H<Subscript>2</Subscript> interface depending on the platinum content on the electrode

Kinetics of processes occurring at H⁺/solid electrolyte/Pt, H₂ three-phase interface are studied subject to the platinum content on the electrode. The study was performed with model electrochemical cells PbO₂/H₃PW₁₂O₄₀/Pt with different platinum content at the working electrode that consisted of platinum deposited onto the E-Tek LT1200-N carbon-nanotubes paper. On the basis of the obtained results, the occurring processes were practically fully separated. It is shown by the analyzing of relaxation curves that there exist at least two processes in the system: the faster one corresponds to the hydrogen reaction; the slower, to the oxygen one. The rates of both processes depend on the platinum content at the working electrode; they have an extreme at the platinum concentration of 0.5 mg/cm². Impedance data allowed revealing the processes’ limiting stages. The experimental data allowed suggesting that at low platinum content the relaxation time is determined by the electrochemical reaction rate; at higher content, by gas diffusion through the platinum dense layer.     

Electrochemical growth of CuInSe<Subscript>2</Subscript> thin film on different substrates from alkaline medium. Characterization of the films

The simultaneous electrodeposition of the system Cu–In–Se was investigated. The study was carried out at pH 8.5 using diethylentriamine as complexing agent for the Cu⁺² ion. The synthesis of CuInSe₂ semiconductor thin films was carried out by electrodeposition on different substrates [indium–tin oxide (ITO) on glass, aluminum and type 304 steel]. The simultaneous codeposition of the Cu, In, and Se was achieved by constant potential electrolysis technique in aqueous solutions containing the elements that conform this material. The deposits of CuInSe₂ were about 4 μm thick, which is thick enough for the photovoltaic effect to take place. The as-deposited films were characterized by atomic emission spectroscopy with inductive coupling plasm (AES-ICP) and scanning electronic microscopy (SEM). Annealed films were characterized X-ray diffraction, optical NIR spectroscopy, and photoelectrochemical studies The films were obtained with a well-defined composition, very close to the expected one. Homogeneous deposit with chalcopyrite structure was produced. A In₂O₃ phase was also observed. Annealing of the film improved the crystallinity of the films. Good photo response, an appropriate absorption coefficient, and a band gap of 1.09 eV were obtained.     

X-ray photoelectron study of the interaction of H<Subscript>2</Subscript> and H<Subscript>2</Subscript>+O<Subscript>2</Subscript> mixtures on the Pt/MoO<Subscript>3</Subscript> model catalyst

The effects of H₂ and H₂ + O₂ gas mixtures of varying composition on the state of the surface of the Pt/MoO₃ model catalyst prepared by vacuum deposition of platinum on oxidized molybdenum foil were investigated by X-ray photoelectron spectroscopy (XPS) at room temperature and a pressure of 5–150 Torr. For samples with a large Pt/Mo ratio, the XP spectrum of large platinum particles showed that the effect of hydrogen-containing mixtures on the catalyst was accompanied by the reduction of molybdenum oxide. This effect results from the activation of molecular hydrogen due to the dissociation on platinum particles and subsequent spill-over of hydrogen atoms on the support. The effect was not observed at low platinum contents in the model catalyst (i.e., for small Pt particles). It is assumed for the catalyst that the loss of its hydrogen-activating ability is a consequence of the formation of platinum hydride. Possible participation of platinum hydride as intermediate in hydrogen oxidation to H₂O₂ is discussed.     

In-situ growth of Co<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles on mesoporous carbon nanofibers: a new nanocomposite for nonenzymatic amperometric sensing of H<Subscript>2</Subscript>O<Subscript>2</Subscript>

The paper describes a nonenzymatic amperometric H₂O₂ sensor that uses a nanocomposite consisting of Co₃O₄ nanoparticles (NPs) and mesoporous carbon nanofibers (Co₃O₄-MCNFs). The Co₃O₄ NPs were grown in situ on the MCNFs by a solvothermal procedure. The synergetic combination of the electrocatalytic activity of the Co₃O₄ NPs and the electrical conductivity of MCNFs as an immobilization matrix enhance the sensing ability of the hybrid nanostructure. The oxidation current, best measured at 0.2 V (vs. SCE) is linear in the 1 to 2580 μM H₂O₂ concentration range, with a 0.5 μM lower detection limit (at an S/N ratio of 3). The sensor is highly selective even in the presence of common electroactive interferents. It was applied to the determination of H₂O₂ in spiked milk samples.

Open image in new window

Graphical abstract Schematic of the synthesis of a nanocomposite consisting of Co₃O₄ nanoparticles (NPs) and mesoporous carbon nanofibers (Co₃O₄-MCNFs) by a solvothermal procedure. It was used as electrocatalyst for direct oxidation of H₂O₂.

     

Effect of active impurities on the condensation of nanoparticles from supersaturated carbon vapor in the combined laser photolysis of C<Subscript>3</Subscript>O<Subscript>2</Subscript> and H<Subscript>2</Subscript>S

The effect of active H₂S, HS^·, and atomic hydrogen impurities on the condensation of highly supersaturated carbon vapor obtained in the combined laser photolysis of a mixture of C₃O₂ and H₂S diluted with argon was studied. The concentrations of carbon vapor, HS^·, and atomic hydrogen obtained in the laser photolysis of the mixture were determined using the absorption cross sections of C₃O₂ and H₂S molecules measured in this work and the measured amount of absorbed laser radiation. The time profiles of the sizes of growing nanoparticles synthesized in C₃O₂ + Ar and C₃O₂ + H₂S + Ar mixtures were measured using the laser-induced incandescence (LII) method. An improved LII model was developed, which simultaneously took into account the heating and cooling of nanoparticles and the temperature dependence of the thermophysical properties of nanoparticles, as well as the cooling of nanoparticles by evaporation and thermal emission. The size distributions of carbon nanoparticles formed in the presence and absence of active impurities were determined with the use of a transmission electron microscope. The final average size of carbon nanoparticles was found to decrease from 12 to 9 nm upon the addition of H₂S to the system, whereas the rate of nanoparticle growth decreased by a factor of 3, and the properties of nanoparticles changed. In particular, the translational energy accommodation coefficient for Ar molecules at the surface of carbon nanoparticles was found to decrease from 0.44 to 0.30. A comparison of the calculated total carbon balance at the early stage of nanoparticle formation with experimental data demonstrated that the reaction C + H₂S → HCS^· + H, which removes a portion of carbon vapor from the condensation process, has a determining effect on the carbon balance in the system. It was found that HS^· and atomic hydrogen affect the carbon balance in the system only slightly. Thus, the experimentally observed decrease in the rate of nanoparticle growth and in the sizes of nanoparticles can be explained by a decrease in the concentration of free carbon upon the addition of H₂S molecules to the system.     

Morphology of carbon nanotubes,obtained by decomposition of ethylene on nickel nanoparticles at various rates of flow and concentration of C<Subscript>2</Subscript>H<Subscript>4</Subscript>

The influence of flow rate and concentration of source of hydrocarbon on the properties of the carbon nanotubes formed in the process of thermal decomposition of ethylene on nickel nanoparticles have been investigated. Changes in the rate of gaseous flow has practically no effect on the specific yield and the mean diameter of the nanotubes. However, an increase in the mean diameter and a decrease in the value of the specific yield occurs with increase in the concentration of ethylene. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 44, No. 4, pp. 228–232, July–August, 2008.     

Polarization Characteristics of Composite Electrodes in Electrochemical Cells with Solid Electrolytes Based on CeO<Subscript>2</Subscript> and LaGaO<Subscript>3</Subscript>

For two types of electrochemical cells with oxygen-conducting solid electrolytes based on lanthanum gallate (LSGM) and cerium oxide (SDC) studied are the temperature dependences of the polarization conductivity of air electrodes prepared from lanthanum-strontium manganite (LSM) and composites LSM-LSGM, LSM-SDC, and LSM-SSZ (SSZ is zirconium dioxide-based electrolyte). Effect of praseodymium oxide, added into these electrodes as a modifier, on their electrochemical properties is examined. Electrochemical systems with an LSM/LSGM interface exhibit low electrochemical activity toward the oxygen reaction, because during the formation of electrodes, LSM interacts with LSGM to form a poorly conducting product.__________Translated from Elektrokhimiya, Vol. 41, No. 5, 2005, pp. 602–606.Original Russian Text Copyright © 2005 by Yaroslavtsev, Kuzin, Bronin, Bogdanovich.     

Oxidative desulfurization of thiophene derivatives with H<Subscript>2</Subscript>O<Subscript>2</Subscript> in the presence of catalysts based on MoO<Subscript>3</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> under mild conditions

The catalysts based on MoO₃/Al₂O₃ were synthesized and tested using aqueous hydrogen peroxide as the oxidant in the oxidative desulfurization of thiophene, benzothiophene (BT) and dibenzothiophene (DBT) into the corresponding sulfones. Among catalysts tested, 15%(MoO₃–WO₃)/Al₂O₃ prepared by a conventional impregnation method was considerably active for the oxidation of thiophene, BT and DBT, which could achieve higher than 99.2% conversions at lower reaction temperature (≤338 K). The use of hexadecyltrimethyl ammonium bromide as the phase-transfer reagent in small amounts could promote the reaction efficiently.     

Electrochemical Synthesis of Co-intercalation Compounds in the Graphite-H<Subscript>2</Subscript>SO<Subscript>4</Subscript>-H<Subscript>3</Subscript>PO<Subscript>4</Subscript>System

Anodic oxidation of highly oriented pyrolytic graphite in an electrolyte containing concentrated sulfuric and anhydrous phosphoric acids is studied for the first time. The synthesis was carried out under galvanostatic conditions at a current I = 0.5 mA and an elevated temperature (t = 80°C). Intercalation compounds of graphite (ICG) are shown to form at all concentration ratios of H₂SO₄ and H³PO⁴ acids. The intercalation compound of step I forms in solutions containing more than 80 wt % H₂SO₄, a mixture of compounds of intercalation steps I and II forms in 60% H²SO⁴, intercalation step II is realized in the sulfuric acid concentration range from 10 to 40%, and a mixture of compounds of intercalation steps III and II is formed in 5% H₂SO₄ solutions. The threshold concentration of H₂SO₄ intercalation is ∼2%. With the decrease in active intercalate (H₂SO₄) concentration, the charging curves are gradually smoothed, the intercalation step number increases, and the potentials of ICG formation also increase. As the sulfuric acid concentration in the electrolyte changes from 96 to 40 wt %, the filled-layer thickness d _i in ICG monotonously increases from 0.803 to 0.820 nm, which apparently is associated with the greater size of phosphoric acid molecules. With further increase in H₃PO₄ concentration in solution, d _i remains unchanged. According to the results of chemical analysis, both acids are simultaneously incorporated into the graphite interplanar spacing and their ratio in ICG is determined by the electrolyte composition.__________Translated from Elektrokhimiya, Vol. 41, No. 5, 2005, pp. 651–655.Original Russian Text Copyright © 2005 by Leshin, Sorokina, Avdeev.     

Kinetic method for acetylsalicylic acid determination based on its inhibitory effect upon the catalytic decomposition of H<Subscript>2</Subscript>O<Subscript>2</Subscript>

The catalytic reaction of catalase was investigated, by means of a Clark oxygen sensor, in the presence of various concentrations of acetylsalicylic acid. Michaelis-Menten kinetic parameters were determined from Lineweaver-Burk plots, obtained in the absence and in the presence of the inhibitor. The inhibition pattern, suggested by the Lineweave-Burk plots, corresponds to a fully mixed inhibition mechanism. A kinetic method, based on the indicator reaction: , was developed for the quantitative determination of acetylsalicylic acid. Calibration graphs of the reciprocal value of first-order rate constant versus acetylsalicylic concentration covered the concentration range (2.99–19.98)×10^–4 mol/L, while the detection limit was 4.12×10^–4 mol/L acetylsalicylic acid with a standard deviation of 2.1×10^–5 mol/L.