Effect of aging time on properties of acrylic impact modifier modified bisphenol A polycarbonate

Polycarbonate (PC) was blended with acrylic impact modifiers (AIMs). The effects of modifiers weight fraction on the Izod impact strength and yield strength of PC/AIM blends were investigated. The samples with 4% modifiers were aged under the T_g of PC in an air‐circulating oven, and the effects of aging time on impact strength, yield strength, modulus, elongation at break, post yield stress drop (PYSD) values, and morphology of fracture surface were investigated. The effects of aging time on the shape of stress–strain curve were also investigated. The aged samples were heat‐treated over the T_g of PC to erase the effects of physical aging. It was found that the drop of impact strength caused by physical aging can be recovered, the increment of yield strength and PYSD value caused by physical aging can only be partly recovered, and the heat‐treatment over the T_g of PC caused further increment of modulus. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2715–2724, 2005     

Mechanical,thermal, and ultraviolet resistance properties of polycarbonate/cerium oxide composites

The composites containing polycarbonate (PC) and cerium oxide (CeO₂) nanoparticles as well as nanoparticles modified with stearic acid (mCeO₂) have been prepared using a melt blending method. The composites are studied by using FTIR spectroscopy, differential scanning calorimetry, thermal gravimetric analysis and scanning electron microscopy, and their tensile strength and ultraviolet (UV) resistance are examined. The results indicate that the introduction of CeO₂ nanoparticles at 1 wt% can improve the mechanical properties of PC, while a weight ratio that is over 1 wt% can lead to a reduction in the tensile strength. Compared with the PC/CeO₂ composites, the PC/mCeO₂ composites provide better mechanical properties. Besides, the introduction of CeO₂ nanoparticles gives PC promising UV resistance. However, different amounts of CeO₂ nanoparticles used provide similar thermal and UV resistance in PC. In a comparison of the PC/CeO₂ and PC/mCeO₂ composites, there are no apparent differences observed between CeO₂ and mCeO₂ on improving the UV resistance of PC.     

Preparation and cryogenic mechanical properties of epoxy resins modified by poly(ethersulfone)

A thermoplastic, poly(ethersulfone) (PES) was used to modify a bisphenol‐F based epoxy resin cured with an aromatic diamine. The initial mixtures before curing, prepared by melt mixing, were homogeneous. Scanning electron microscopy (SEM) micrographs of solvent‐etched fracture surfaces of the cured blends indicated that phase separation occurred after curing. The cryogenic mechanical behaviors of the epoxy resins were studied in terms of tensile properties and Charpy impact strength at cryogenic temperature (77 K) and compared to their corresponding behaviors at room temperature (RT). The addition of PES generally improved the tensile strength, elongation at break, and impact strength at both RT and 77 K except the RT tensile strength at 25 phr PES content. It was interesting to observe that and the maximum values of the tensile strength, elongation at break, and impact strength occurred at 20 phr PES content where a co‐continuous phase formed. Young's modulus decreased slightly with the increase of the PES content. Moreover, the tensile strength and Young's modulus at 77 K were higher than those at RT at the same composition, whereas the elongation at break and impact strength showed the opposite results. Finally, the differential scanning calorimetry analysis showed that the glass transition temperature (T_g) was enhanced by the addition of PES. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 612–624, 2008     

硬脂酸改性纳米羟基磷灰石表面性能的研究

采用硬脂酸(C₁₇H₃₅COOH)对纳米羟基磷灰石(n-HA)表面进行处理,并研究了n-HA与C₁₇H₃₅COOH的界面作用。透射电子显微镜(TEM)、傅立叶红外光谱(FTIR)以及X光电子能谱(XPS)分析表明,C₁₇H₃₅COOH在n-HA表面黏附,其中羧酸根离子(-COO^-)与钙离子(Ca^2＋)之间形成了稳定的离子键,以羧酸钙形式存在。C₁₇H₃₅COOH改性后的n-HA与聚碳酸酯(PC)复合后,复合材料的力学性能与未改性n-HA相比有明显提高。扫描电子显微镜(SEM)结果显示,经处理后的HA微粒在PC中分散均匀,两者间结合紧密,无明显界面,复合材料的断裂呈明显的韧性断裂,随着n-HA无机粒子含量增加,复合材料的断裂也逐渐向韧性与脆性断裂共存转变。     

Effects of thermal history,crystallinity, and solvent on the transitions and relaxations in poly(bisphenol-A carbonate)

The following system of nomenclature for the transitions and relaxations in polycarbonate has been proposed: α = T_g = 150, β = 70, γ = ?100, and δ = ?220°C (frequency range of 10–50 Hz). The three component peaks of the γ relaxation are denoted by γ₁, γ₂, and γ₃ relaxations correspond to phenylene, coupled phenylene-carbonate, and carbonate motions, respectively. Dynamic mechanical analysis of poly(bisphenol-A carbonate) using the DuPont 981–990 DMA system shows that the magnitude of the β relaxation depends upon the thermal history of the polycarbonate; annealing greatly reduces the intensity of the β relaxation. A relaxation map constructed for the β relaxation gives an activation energy of 46 kcal/mol. Exposure of polycarbonate to methylene chloride vapor for various times shows that after an induction period of about 5 min the intensity of the γ₃ relaxation at ?78°C decreases whereas the intensity of the γ₁ relaxation of ?30°C is unaffected and the ratio E″(γ₁)/E″(γ₃) increases linearly with the square root of time. This has been ascribed to the interaction of methylene chloride on the carbonate group in polycarbonate. Thermal crystallization of polycarbonate does not affect the positions of the γ relaxation and the glass transition peaks, but merely reduces their intensity. The glass transition peak intensity falls off sharply in comparison to the γ relaxation intensity. Both the γ₃ and γ₁ peaks in polycarbonate have been observed simultaneously for the first time by dynamic mechanical analysis. Impact strength measurements show that methylene chloride treatment of polycarbonate results in a change in mode of failure from ductile to brittle with a resultant 40-fold reduction in impact energy for fracture. Thermally crystallized polycarbonate exhibits brittle fracture with very low force and energy at break.     

Preparation and properties of enhanced nanocomposites based on PLA/PC blends reinforced with silica nanoparticles

In order to lower brittleness of biobased polylactic acid (PLA), its blending with polycarbonate and nanosilica is aimed. In this line, to increase compatibility of the ingredients, dicumyl peroxide (DCP) and Cobalt (II) acetylacetonate (Co) were used as grafting and transesterification catalysts, respectively. The X‐ray diffraction (XRD) spectra demonstrated high compatibility of the ingredients by broadening of the PLA characteristic peaks and, also, good dispersion of nanosilica particles, especially in PLA/PC/Silica/Co sample. The EDX maps confirmed good nanosilica dispersion, too. The silica nanoparticle size was ranged from 20 to 100 nm in transmission electron microscopy (TEM) pictures. All nanocomposites showed improved thermal stability in thermogravimetric analysis (TGA). Differential scanning calorimetry (DSC) results demonstrated lower T_g, T_m, and crystallinity values for the fabricated nanocomposites. Notably, the dynamic mechanical thermal analysis (DMTA) curves confirmed the T_g, T_m, and T_cc trend obtained in DSC; moreover, much higher surface under tan δ peak for PLA/PC/Silica/Co sample was obtained, which implies its higher toughness. The precise tensile study of the samples confirmed significantly higher elongation at break of the nanocomposites, more considerably in PLA/PC/Silica/Co sample, with nearly negligible defect on tensile strength and modulus. In a concise, the obtained results confirmed the higher efficiency of Co catalyst, which leads to the sample with improved characteristics compared with DCP.     

High performance polymer films 4. Mechanical behavior

Tensile properties of the polyimide and copolyimide films based on two dianhydrides, pyromellitic dianhydride (PMDA) and 3,3^′,4,4^′-benzophenonetetracarboxylic dianhydride (BTDA) and two diamines, 4,4^′-oxydianiline (ODA), and a proprietary aromatic diamine (PD) have been described. The tensile strength of the films containing higher proportions of BTDA or PMDA and PD is much higher (except the fully rigid film based on PMDA-PD which is brittle in nature) than the films containing higher proportion of ODA moiety. The films containing PD as the diamine moiety exhibit high initial moduli than the films containing exclusively or mainly ODA as the diamine moiety. The films having higher concentration of the -O- linkage originated from diamine ODA are found to exhibit higher elongation values. There is found to be no direct correlation between η_inh of the precursor casting solutions and mechanical properties of structurally different polyimide/copolyimide films. For a particular polyimide or copolyimide film, the tensile strength value is found to be less sensitive than the elongation to the variation of η_inh value of the precursor poly(amic acid) or copoly(amic acid). Tensile strength and elongation of the film, basically rigid in nature, may be improved by post-curing at 360°C/370°C. While Kapton H film retains 78% and 63.5% of its tensile strength and % elongation at break (% E_b) respectively after hot-wet mechanical test, the film based on BTDA 80, PMDA 20 and PD shows an increase of about 27% and 22% in its tensile strength and % E_b respectively.     

Effects of gamma radiation on the photoluminescence properties of polycarbonate matrices doped with terbium complex

Luminescent films containing terbium complex [Tb(acac)₃(H₂O)₃] (acac=acetylacetonate) doped into a polycarbonate (PC) matrix were prepared and irradiated at low-dose gamma radiation with ratio of 5 and 10 kGy. The PC polymer was doped with 5% (w/w) of the Tb³⁺ complex. The thermal behavior was investigated by utilization of differential scanning calorimetry (DSC) and thermogravimetry analysis (TGA). Changes in thermal stability due to the addition of doping agent into the polycarbonate matrix. Based on the emission spectra of PC:5% Tb(acac)₃ film were observed the characteristic bands arising from the ⁵D₄→⁷F_J transitions of Tb³⁺ ion (J=0–6), indicating the ability to obtain the luminescent films. Doped samples irradiated at low dose of gamma irradiation showed a decrease in luminescence intensity with increasing of the dose.     

Study of the morphology and properties of melt-mixed polycarbonate-POSS nanocomposites

In this work, the morphology and thermo-mechanical behaviour of nanocomposites formed by a polycarbonate (PC) matrix and polyhedral oligomeric silsesquioxane with phenethyl substituents (Ph-POSS) have been studied. The Ph-POSS nanocages were added to the PC by direct melt blending at loadings between 0% and 15 wt%. Good dispersion was achieved up to 5 wt% of nanofiller. At higher loadings micron-sized aggregates were observed in the nanocomposites by scanning and transmission electron microscopy. Increasing of Ph-POSS content lead to phase separation, agglomeration and low values on the final properties. The DSC and DMA analyses showed that increasing the amount of nanocages caused a continuous decrease on the composite’s T_g. Although little increments on the polycarbonate decomposition temperature were found, the presence of Ph-POSS did not improve significantly the thermal stability. Under nitrogen atmosphere the degradation mechanism of PC was not affected by the POSS. The residual weights obtained under oxygen atmosphere were in agreement with the theoretical weights of the Ph-POSS added. With respect to the nanocomposites mechanical properties the most remarkable trend was an improvement on the composite’s yield stress having the maximum at 5 wt% of nanofiller. Higher amounts of Ph-POSS lead to a decrease on the yield stress, finding even lower values than the one corresponding to the neat matrix. This behaviour has been attributed to the presence of large POSS agglomerates with low adhesion to the polymer matrix. A continuous decrease on the strain at break was also observed, reflecting the brittle character of the formed composites.     

Properties and morphologies of UV‐cured epoxy acrylate blend films containing hyperbranched polyurethane acrylate/hyperbranched polyester

The properties and morphologies of UV‐cured epoxy acrylate (EB600) blend films containing hyperbranched polyurethane acrylate (HUA)/hyperbranched polyester (HPE) were investigated. A small amount of HUA added to EB600 improved both the tensile strength and elongation at break without damaging its storage modulus (E′). The highest tensile strength of 31.9 MPa and an elongation at break around two times that of cured pure EB600 were obtained for the EB600‐based film blended with 10% HUA. Its log E′ (MPa) value was measured to be 9.48, that is, about 98% of that of the cured EB600 film. The impact strength and critical stress intensity factor (K_1c) of the blends were investigated. A 10 wt % HUA content led to a K_1c value 1.75 times that of the neat EB600 resin, and the impact strength of the EB600/HPE blends increased from 0.84 to 0.95 kJ m^?1 with only 5 wt % HPE addition. The toughening effects of HUA and HPE on EB600 were demonstrated by scanning electron microscopy photographs of the fracture surfaces of films. Moreover, for the toughening mechanism of HPE to EB600, it was suggested that the HPE particles, as a second phase in the cured EB600 film, were deformed in a cold drawing, which was caused by the difference between the elastic moduli of HPE and EB600. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3159–3170, 2005     

Mechanical, thermal and degradation properties of poly(d,l-lactide)/poly(hydroxybutyrate-co-hydroxyvalerate)/poly(ethylene glycol) blend

The mechanical, thermal and biodegradable properties of poly(d,l-lactide) (PDLLA), poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) and poly(ethylene glycol) (PEG) blends were studied. The influence of PEG on the tensile and impact strengths of the blends was investigated. The results showed that the toughness and elongation at break of the PDLLA/PHBV (70/30) blends were greatly improved by the addition of PEG, and the notched Izod impact strength increased about 400% and the elongation at break increased from 2.1% to 237.0%. The thermal and degradation properties of the blends were investigated by differential scanning calorimeter (DSC) and thermogravimetric analyzer (TGA), it was found that the thermal stability of PHBV in the presence of PDLLA was improved. The degradation test showed that the addition of PEG could notably accelerate the biodegradation of the blends in the soil at room temperature, and the mass loss is about 20% after 30 days of the storage.     

Mechanical and thermal properties and flame retardancy of phosphorus-containing polyhedral oligomeric silsesquioxane (DOPO-POSS)/polycarbonate composites

A novel polyhedral oligomeric silsesquioxane containing 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO-POSS) has been incorporated into polycarbonate (PC) composites in order to study its effect on mechanical and thermal properties and flame retardancy. The mechanical and thermal properties of the DOPO-POSS/PC composites have been investigated by tensile and flexural testing, DSC, and DMA. Slight enhancements of yield stress, and flexural strength and modulus, and obvious decreases of fracture strength and strain of the DOPO-POSS/PC composites were observed with an increase in DOPO-POSS loading. The glass transition temperatures (T_g) of the composites were reduced with increasing DOPO-POSS loading. The morphology of the PC composites was evaluated by SEM, which indicated that the DOPO-POSS was dispersed with a particle size of 100-250 nm in the PC matrix. The thermal degradation behaviour and flame retardancies of PC composites with different DOPO-POSS loadings were investigated by TGA, LOI, UL-94 standard, and cone calorimetry. The composite had an LOI value of 30.5 and a UL-94 rating V-0 when the content of DOPO-POSS was 4%.     

Physical aging in polycarbonate nanocomposites containing grafted nanosilica particles: A comparison between enthalpy and yield stress evolution

Understanding and controlling physical aging below the glass transition temperature (T_g) is very important for the long‐term performance of plastic parts. In this article, the effect of grafted silica nanoparticles on the physical aging of polycarbonate (PC) below the T_g is studied by using the evolution of the enthalpy relaxation and the yield stress. The nanocomposites were found to reach a thermodynamic equilibrium faster than unfilled PC, implying that physical aging is accelerated in presence of grafted nanosilica particles. The Tool‐Narayanaswamy‐Moynihan model shows that the aging is accelerated by the grafted silica nanoparticles, but the molecular mechanism responsible for physical aging remains unaltered. Furthermore, dynamic mechanical analysis shows that the kinetics of physical aging can be related to a free volume distribution or a local attraction‐energy distribution as a result of the change in mobility of the polymer chain. Finally, a qualitative equivalence is observed in the physical aging followed by both the enthalpy relaxation and yield stress. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2069–2081     

Synthesis and characterization of polyaniline filled PU/PMMA interpenetrating polymer networks

A series of conducting interpenetrating polymer networks (IPNs), are prepared by sequential polymerization of castor oil based polyurethane (PU) with poly(methyl methacrylate) (PMMA) and polyaniline doped with camphor sulphonic acid (PAni)_CSA. The effect of different amount of PAni (varies from 2.5-12.5%) on the properties of PU/PMMA (50/50) IPNs such as electrical properties like conductivity, dielectric constant and dissipation factor; mechanical properties like tensile strength and percentage elongation at break have been reported. (PAni)_CSA filled IPNs shows improved tensile strength than the unfilled IPN system. The thermal stability and surface morphology of unfilled and (PAni)_CSA filled PU/PMMA (50/50) IPN sheets were investigated using a thermogravimetric analyzer (TGA) and a scanning electron microscope (SEM). TGA thermograms of (PAni)_CSA filled PU/PMMA (50/50) IPNs show a three-step thermal degradation process. SEM micrograms of filled PU/PMMA IPN system shows spherulitic structure at higher concentration of (PAni)_CSA.     

Effect of radiation dose on the properties of natural rubber nanocomposite

Effect of radiation dose and carbon nanotubes (CNT) on the mechanical properties of standard Malaysian rubber (SMR) was investigated in this study. SMR nanocomposites containing 1–7 phr CNT were prepared using the solvent casting method and the nanocomposites were radiated at doses of 50–200 kGy. The change in mechanical properties, especially, tensile strength (Ts), elongation at break (Eb), hardness and tensile modulus at 100% elongation (M₁₀₀) were studied as a function of radiation dose. The structure and morphology of reinforced natural rubber was investigated by FESEM, TEM and AFM in order to gain further evidence on the radiation-induced crosslinking. It was found that the Ts, M₁₀₀ and the hardness of the SMR/CNT nanocomposites significantly increased with radiation dose; the elongation at break exhibited an increase up to 100 kGy, and a downward trend thereafter. Results on gel fraction further confirmed the crosslinking of SMR/CNT nanocomposites upon radiation.     

Investigation of thermally stimulated charge relaxation mechanism in SiO<Subscript>2</Subscript> filled polycarbonate nanocomposites

The thermally stimulated charge relaxation properties of polycarbonate (PC) filled with SiO₂ nanofiller were studied by means of thermally stimulated discharge current (TSDC). The nanocomposite samples were further characterized by UV–vis spectroscopy, scanning electron microscopy, energy dispersive X-ray spectra, and differential scanning calorimetry (DSC) techniques to investigate the dispersion of nanofillers in polymer matrix and glass transition temperature. All pristine and nanocomposites samples of thickness about 25 μm were prepared using solution mixing method. The suitable weight percentage of SiO₂ nanofillers has been chosen to prevent the nonuniform dispersion. TSDC measurement of PC (Pristine) and PC+ (7% SiO₂) shows the single peak, while TSDC characteristic of other nanocomposites are showing two peaks. The higher temperature TSDC peak of pristine and nanocomposites samples is originated due to the charge relaxation from shallower and deeper trapping sites, however, low temperature peak is caused by dipolar relaxation of charge carriers. Since the position of higher temperature TSDC peak is generally an analysis of glass transition temperature of polymer/polymer nanocomposites. The authors have observed that the temperature of this peak is almost same as the T _g measured by DSC with 0 to ±5% variation. This article presents the deeper understanding of charge relaxation mechanism caused by SiO₂ nanofillers in polycarbonate.     

Synergistic toughening effect of β-nucleating agent and long chain branching on polypropylene random copolymer

β-nucleated long chain branched (LCB) polypropylene random copolymers (PPRs) were prepared via reactive extrusion by introducing β nucleating agent (NA), dicumyl peroxide (DCP) and various contents of 1, 6-Hexanediol diacrylate (HDDA) into PPR. Results of Fourier infrared spectroscopy (FTIR) and the rheological properties demonstrate the existence of LCB polypropylene. Mechanical properties including impact strength, tensile strength and elongation at break were studied. The crystal structure, morphology and crystallization behavior were investigated via wide-angle X-ray diffraction (WAXD), polarized light microscopy (PLM) and differential scanning calorimetry (DSC). Non-isothermal crystallization kinetics using the Jeziorny method was also studied. The results show an increased LCB degree with increasing HDDA amount. For the sample with a moderate LCB level, synergistic toughening effect of NA and LCB is achieved without deterioration of yield strength or elongation at break, partially because of its higher β-phase content and much smaller spherulite size. It exhibits the minimum values of T_c and Z_c1, and the maximum values of t_1/2 and n₁ in the primary stage of crystallization, regardless of the cooling rate, indicating a slower crystallization rate and more complicated nucleation and crystal growth model.     

Blends of polycarbonate and ethylene-1-octylene copolymer

The mechanical properties and morphology of polycarbonate/ethylene-1-octylene copolymer (PC/POE) binary blends and PC/POE/ionomer ternary blends were investigated. The tensile strength and elongation at break of the PC/POE blends decreased with increasing the POE content. The impact strength of the PC/POE blends showed less dependence on thickness than that of PC. And the low-temperature impact strength of PC was modified effectively by addition of POE. The morphology of the PC/POE blends was observed by scanning electron microscope. The PC/POE weight ratio had a great effect on the morphology of the PC/POE blends. For the PC/POE (80/20)/ionomer ternary blends, low content (0.25 and 0.5 phr) of ionomer could increase the tensile properties of PC/POE (80/20) blend and had little effect on the impact strength. And 0.5 phr ionomer made the dispersed domain distribute more uniformly and finely than the blend without it. But with high content of ionomer, the degradation of PC made the mechanical properties of the blends deteriorate. Blending PC and ionomer proved the degradation of PC, and the molecular weight decreased with increasing the ionomer content.     

Rheological and mechanical properties of antiplasticized and rubber-toughened bisphenol A polycarbonate

The addition of a high-T_g aromatic diluent to bisphenol A polycarbonate (PC) reduced T_g and melt viscosity while raising elastic modulus and yield stress substantially. Ultimate tensile elongation and impact toughness were badly affected. However, the addition to these antiplasticized blends of a small amount of a rubber modifier restored impact toughness and elongation but left the blend with increased melt fluidity and ambient stiffness re: neat PC. The key to this rebalancing of the properties of PC was found to be the disappearance of the plane strain crack instability that is a hallmark of the neat resin. The deformation mechanism in all the rubber-containing blends in all failure tests, regardless of geometric constraint and strain rate was found to be shear flow alone. The large plastic zone seen at the plane strain crack tip appears to involve rubber particle cavitation as well. © 1995 John Wiley & Sons, Inc.     

Crystallinity in quasi-alternating cycloolefin copolymers: Overcoming brittleness

Cycloolefin copolymers (COCs, which are produced via ethylene/cycloolefin copolymerization) and cycloolefin polymers (COPs, which are synthesized by a rather complicated two-step process via ring-opening metathesis polymerization and subsequent hydrogenation) are commercialized materials used especially widely in optical applications. Although a COP can be used after processing into a film, films made from conventional COCs are too brittle. Optical-grade COCs and COPs are generally known as amorphous polymers. By contrast, here, a quasi-alternating ethylene/norbornene copolymer (norbornene content 56 mol%), prepared from a constrained-geometry Hf complex, shows some melting (T_m) signals in a broad temperature range (150–200°C) in the first heating scan of differential scanning calorimetry (DSC) when the samples are prepared by precipitation from a toluene solution. In the second heating scan, only glass transition (T_g) signals are observed at ~140°C with disappearance of T_m signals. The quasi-alternating ethylene/norbornene copolymer has better mechanical properties (greater elongation at break) than random congeners, which do not show any melting signal, though elongation at break is still inferior to that of the COP which shows the melting signal in the first heating scan of DSC. The enhanced mechanical properties of the quasi-alternating ethylene/norbornene copolymer and commercial-grade COP may be ascribed to semicrystallinity observed in the first heating scan.