Synergistic Effect of Nucleation and Compatibilization on the Polylactide and Poly(butylene adipate-co-terephthalate) Blend Films

Polylactide(PLA) films blended with 10 wt% poly(butylene adipate-co-terephthalate)(PBAT) were prepared by using a twin screw extruder in the presence of the nucleating agent of titanium dioxide(TiO_2) and the compatibilizers of toluene diisocyanate(TDI) and PLA-grafted-maleic anhydride(PLA-g-MA). The synergistic effect of the nucleation and compatibilization on the properties and crystallization behavior of the PLA/PBAT(PLB) films was explored. The results showed that the addition of TiO_2 significantly enhanced the tensile strength and the impact tensile resistance of the PLB films while slightly decreased its thermal stability. In addition, the compatibilizers of TDI and PLA-g-MA in the system not only affected the crystallinity and cold crystallization process of the PLB films, but also increased the mechanical properties of them due to the improvement of the interfacial interaction between PLA and PBAT revealed by the morphological measurement. The synergistic effects of the nucleating agent and the compatibilizer afforded the blend films with increased tensile strength and impact tensile toughness, improved cold crystallization property and X_c.     

Chemical modification of poly(lactic acid) and its use as matrix in poly(lactic acid) poly(butylene adipate-co-terephthalate) blends

Poly(lactic acid), PLA, was chemically modified with maleic anhydride (MA) by reactive extrusion. The effect of this modification on molar mass (MM) and acidity was assessed by means of size-exclusion chromatography (SEC) and titration, respectively. PLA MM decreased in the presence of MA solely and of MA and peroxide. Reduction in MM was monitored by the increase in acidity. PLA blends containing poly(butylene adipate-co-terephthalate) (PBAT) were prepared through different mixing protocols, PLA/PBAT, PLA-g-MA/PBAT and PLA/PBAT/MA/peroxide (PLA/PBAT in situ). SEC results and rheological properties revealed reduction in MM and viscosity of the modified blends. PLA/PBAT presented increase in MM and bimodal MM distribution. The calculated interfacial tension was significantly lower for the modified blends, despite the lower average particle area of PLA/PBAT. Surprisingly, the modified blends presented higher yield strength than that predicted by the rule of mixtures, which might indicate interfacial reactions.     

Effect of ethylene-co-vinyl acetate-glycidylmethacrylate and cellulose microfibers on the thermal,rheological and biodegradation properties of poly(lactic acid) based systems

The properties and biodegradation behavior of blends of poly(lactic acid) (PLA) and ethylene-vinyl acetate-glycidylmethacrylate copolymer (EVA-GMA), and their composites with cellulose microfibers (CF) were investigated. The blends and composites were obtained by melt mixing and the morphology, phase behavior, thermal and rheological properties of PLA/EVA-GMA blends and PLA/EVA-GMA/CF composite films were investigated as a function of the composition. The disintegrability in composting conditions was examined by means of morphological, thermal and chemical analyses to gain insights into the post-use degradation processes. The results indicated a good compatibility of the two polymers in the blends with copolymer content up to 30 wt.%, while at higher EVA-GMA content a phase separation was observed. In the composites, the presence of EVA-GMA contributes to improve the interfacial adhesion between cellulose fibers and PLA, due to interactions of the epoxy groups of GMA with hydroxyls of CF. The addition of cellulose microfibers in PLA/EVA-GMA system modifies the rheological behavior, since complex viscosity increased in presence of fibers and decreased with an increase in frequency. Disintegration tests showed that the addition of EVA-GMA influence the PLA disintegration process, and after 21 days in composting conditions, blends and composites showed faster degradation rate in comparison with neat PLA due to the different morphologies induced by the presence of EVA-GMA and CF phases able to allow a faster water diffusion and an efficient PLA degradation process.     

Characterization and biodegradability of polyester bioplastic-based green renewable composites from agricultural residues

The biodegradability, morphology, and mechanical properties of composite materials consisting of acrylic acid-grafted poly(butylene succinate adipate) (PBSA-g-AA) and agricultural residues (rice husk, RH) were evaluated. Composites containing acrylic acid-grafted PBSA (PBSA-g-AA/RH) exhibited noticeably superior mechanical properties compared with those of PBSA/RH due to greater compatibility with RH. The dispersion of RH in the PBSA-g-AA matrix was highly homogeneous as a result of ester formation, and the consequent creation of branched and cross-linked macromolecules, between the carboxyl groups of PBSA-g-AA and hydroxyl groups in RH. Each composite was subject to biodegradation tests in an Azospirillum brasilense BCRC 12270 liquid culture medium. The bacterium completely degraded both the PBSA and the PBSA-g-AA/RH composite films. Morphological observations indicated severe disruption of the film structure after 20-40 days of incubation. The PBSA-g-AA/RH (20 wt%) films were not only more biodegradable than those made of PBSA but also exhibited lower molecular weight and intrinsic viscosity, implying a strong connection between these characteristics and biodegradability.     

Preparation of PLA-based nanocomposites modified by nano-attapulgite with good toughness-strength balance

Polylactic acid (PLA) was modified by poly (butylene adipate-co-terephthalate) (PBAT) and nano-attapulgite (AT) using the melt blending technique. Ethylene-butyl acrylate-glycidyl methacrylate (E-BA-GMA) was used as a compatibilizer which can bond the AT nanoparticles with PLA/PBAT matrix by interaction between the epoxy and hydroxyl groups. The effects of the AT content on the mechanical properties, thermal properties, crystallinity and morphology of PLA/PBAT/ATT nanocomposites were investigated. The results showed that the tensile strength, elongation at break and impact strength of PLA/PBAT could be simultaneously increased by incorporating AT nanoparticles. PLA/PBAT/AT nanocomposites possessed higher thermal stability than pure PLA/PBAT. In the ternary composite system of PLA/PBAT/AT, AT acted as a heterogeneous nucleating agent and was able to increase the crystallization temperature. When the AT content was low (≤2.5 wt%), AT nanoparticles could uniformly disperse in the PLA/PBAT matrix. In general, AT was an effective filler to reinforce and toughen PLA/PBAT blend simultaneously, and the PLA/PBAT/AT nanocomposite with 2.5 wt% AT exhibited a good combination of strength and toughness.     

Mechanical property and biodegradability of solution‐cast films prepared from amphiphilic polylactide‐grafted dextran

Polylactide (PLA)‐grafted dextran was synthesized with a trimethylsilyl protection method to produce novel biodegradable, biomedical materials. PLA‐grafted dextrans with various lengths and numbers of graft chains were synthesized. The properties of solution‐cast films prepared from PLA‐grafted dextrans were investigated with thermal and dynamic mechanical analyses. The graft‐copolymer films exhibited lower glass‐transition temperatures, melting temperatures (T_m's), and crystallinities as well as higher viscosity properties as compared with poly‐L ‐lactide film. The T_m and crystallinity and mechanical properties at 37 °C could be adjusted by controlling the molecular structure such as the lengths and numbers of graft chains. Furthermore, the biodegradability of PLA‐grafted dextran films was investigated through the weight change of film and the molecular weight change of polymer during the in vitro degradation test. PLA‐grafted dextrans exhibited different degradation behavior from poly‐L ‐lactide with the introduction of a polysaccharide segment and branched structure as well as the change of end‐functional group. The degradation rate of PLA‐grafted dextran and the cast film prepared from PLA‐grafted dextran could be adjusted by controlling the sugar content or the length of graft chains. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2462–2468, 2003     

Improving polylactide/starch biocomposites by grafting polylactide with acrylic acid--characterization and biodegradability assessment

In this article, the properties of a polylactide and starch composite (PLA/starch) and an acrylic acid grafted polylactide and starch composite (PLA-g-AA/starch) were compared. The composite containing PLA-g-AA was found to have much better dispersion and homogeneity of starch in the polymer matrix than the composite containing PLA, indicating better compatibility between the two phases. Better mechanical and thermal properties of the PLA-g-AA/starch composite, notably an increase in tensile strength and elongation at breakpoint, evidenced its superiority to the PLA/starch composite. Furthermore, the lower viscosity of PLA-g-AA/starch makes it easier to process than PLA/starch. Weight loss on exposure to a soil environment over a period of three months showed that the starch in the composites was almost completely biodegradable, even at a high degree of substitution (60 wt.-% starch). After three months in soil, a reduction in the mechanical properties of the blends was observed, especially in those with higher starch contents.     

Morphology and properties of biodegradable poly (lactic acid)/poly (butylene adipate-co-terephthalate) blends with different viscosity ratio

Phase morphology exerts a tremendous influence on the properties of polymer blends. The development of the blend morphology depends not only on the intrinsic structure of the component polymers but also on extrinsic factors such as viscosity ratio, shearing force and temperature in the melt processing. In this study, various poly (butylene adipate-co-terephthalate) (PBAT) materials with different melt viscosity were prepared, and then poly (lactic acid) (PLA)/PBAT blends with different viscosity ratio were prepared in a counter-rotating twin-screw extruder under constant processing conditions. The influence of viscosity ratio on the morphology, mechanical, thermal and rheological properties of PLA/PBAT (70/30 w/w) blends was investigated. The experimental results showed that the morphology and properties of PLA/PBAT blends strongly depended on the viscosity ratio. Finer size PBAT phase were observed for viscosity ratio less than 1 (λ < 1) compared to samples with λ > 1. It was found that the interfacial tensions of PLA and PBAT were significantly different when the viscosity ratio was changed, the lowest interfacial tensions (0.12 mN/m) was obtained when the viscosity was 0.77. Additionally, the maximal tensile strength in PLA/PBAT blends were obtained when the viscosity ratio was 0.44, while the maximal impact properties were obtained when the viscosity ratio was 1.95.     

On novel bio-hybrid system based on PLA and POSS

In this work, a novel strategy for the preparation of bio-hybrid systems based on polylactic acid (PLA) and polyhedral oligomeric silsesquioxane (POSS) was developed. Indeed, the new method consists in a preliminary functionalization of the polymer matrix and a subsequent reaction of silsesquioxane molecules, characterized by amino or hydroxyl functionalities, potentially capable of reacting with maleic anhydride groups created onto PLA by a free radical process. The method adopted to create maleic anhydride-grafted polylactic acid (PLA-g-MA) allowed to graft 0.7 wt% of MA onto the polymer backbone, avoiding a dramatic reduction of PLA molecular mass. ¹H-NMR measurements demonstrated a different reactivity of the two used POSS, namely trans-cyclohexanediolisobutyl POSS (POSS-OH) and aminopropyl heptaisobutyl POSS (POSS-NH₂). Indeed, the amino group of POSS-NH₂ was found to react with the maleic anhydride group of PLA-g-MA allowing to obtain a hybrid system, carrying silsesquioxane molecules along the polymer backbone while the reactivity of POSS-OH turned out to be much lower. Thermal properties of the synthesized hybrid systems were assessed by means of DSC measurements. Indeed, the presence of POSS grafted onto the macromolecular chain was found to improve PLA crystallinity, by affecting the crystal nucleation density. Moreover, a decrease of surface water wettability was observed in the films made of PLA-g-MA/POSS-NH₂.     

Replication and surface properties of micro injection molded PLA/MWCNT nanocomposites

Multi-walled carbon nanotube (MWCNT) reinforced polylactide (PLA) nanocomposites were injected molded into a mold with micro needle patterns. In order to alleviate the hesitation effect caused by an increased melt viscositgy of PLA/CNT nanocomposites, the effects of the injection speed and holding pressure on the replication property were investigated. The effects of MWCNTs on the crystallization, thermal behavior, replication properties, replication and surface properties of micro injection molded PLA/CNT nanocomposites were investigated. An analysis of crystallinity and thermal behavior indicated that the MWCNTs promoted the unique α’ to α crystal transition of PLA, leading to an enhancement of surface modulus and hardness, as measured using a nanoindentation technique. The specific interaction between PLA and MWCNTs was characterized using an equilibrium melting point depression technique. Furthermore, the MWCNTs increased the activation energy for thermal degradation of PLA due to the physical barrier effect. The improved replication quality of the microfeatures in the PLA/MWCNT nanocomposites has been achieved by elevating injection speed and holding pressure, which enhances the polymer filling ability within the micro cavity. A replication ratio greater than 96% for the micro injection molded PLA/CNT nanocomposites were achieved at holding pressure of 100 MPa and injection speed of 120 mm/s. This study shows that processing conditions significantly influence the replication and surface properties of micro injection molded PLA/CNT nanocomposites.     

Enhanced directional thermal conductivity of polylactic acid/polybutylene adipate terephthalate ternary composite filled with oriented and surface treated boron nitride

A combination of solution casting and melt extrusion technique was used to fabricate Boron nitride (BN)-filled Polylactic acid (PLA)/polybutylene adipate terephthalate (PBAT) blend composites. The BN particles were surface treated with a silane coupling agent and functionalization was confirmed via spectroscopic analysis. Field emission scanning electron microscopy confirmed that the BN surface treatment improved the particle adhesion with the polymer matrices and acted as a compatibilizer for the polymers. Moreover, changes in the particle orientation in the blend composite yielded improved thermal conductivity in different directions. The inclusion of the treated BN particles enhanced the in-plane (~1.1 W m⁻¹K⁻¹) and through-plane (~0.8 W m⁻¹K⁻¹) thermal conductivity of the composites as compared to the neat PLA. In addition, the storage modulus of the composite become more than 3 GPa that is twice that of the PLA/PBAT blend with a reasonable tensile property. In general, compared with the PLA/PBAT blend, the blend composites exhibited superior thermal and mechanical properties.     

Development of Functional Composite Cu(II)-Polyoxometalate/PLA with Antimicrobial Properties

Novel composite self-disinfecting films of polylactic acid (PLA) filled with nanosized particles of double sodium–copper(II) paratungstate B Na₂Cu₃(CuOH)₂[W₁₂O₄₀(OH)₂]·32H₂O (POM) were developed. The solvent casting (POM/PLA film) and solvent-free melt extrusion methods (Extr. POM/PLA film) were applied for film preparation. The copper (II) ion release to water from both types of the films after 10 days at different temperatures demonstrated that the PLA matrix acts as a diffusion barrier, and the resulting concentration of released copper in water at room temperature remained low, at 0.79% for POM/PLA film and 0.51% for Extr. POM/PLA film. The POM-containing films reveals a significant inhibitory effect against E. coli ATCC 25922 in the agar diffusion test. The numbers of CFUs in washes of the films after incubation for 24 h were found to be 3.6 log CFU mL^–1 (POM/PLA film) and 4.1 log CFU mL^–1 (Extr. POM/PLA film). The films combine the antibacterial properties of POM and a bio-based polymer matrix, which makes them a prospective coating material for applications in hospital indoor environments. Excellent thermal stability of POM gives a technological advantage for industrial manufacturing to allow the processing of novel composite material in the solvent free (molten) state.     

Effects of Rice Straw Powder (RSP) Size and Pretreatment on Properties of FDM 3D-Printed RSP/Poly(lactic acid) Biocomposites

To develop a new kind of environment-friendly composite filament for fused deposition modeling (FDM) 3D printing, rice straw powder (RSP)/poly(lactic acid) (PLA) biocomposites were FDM-3D-printed, and the effects of the particle size and pretreatment of RSP on the properties of RSP/PLA biocomposites were investigated. The results indicated that the 120-mesh RSP/PLA biocomposites (named 120#RSP/PLA) showed better performance than RSP/PLA biocomposites prepared with other RSP sizes. Infrared results showed that pretreatment of RSP by different methods was successful, and scanning electron microscopy indicated that composites prepared after pretreatment exhibited good interfacial compatibility due to a preferable binding force between fiber and matrix. When RSP was synergistically pretreated by alkaline and ultrasound, the composite exhibited a high tensile strength, tensile modulus, flexural strength, and flexural modulus of 58.59, 568.68, 90.32, and 3218.12 MPa, respectively, reflecting an increase of 31.19%, 16.48%, 18.75%, and 25.27%, respectively, compared with unmodified 120#RSP/PLA. Pretreatment of RSP also improved the thermal stability and hydrophobic properties, while reducing the water absorption of 120#RSP/PLA. This work is believed to provide highlights of the development of cost-effective biocomposite filaments and improvement of the properties of FDM parts.     

Synergistic effect of nucleation and compatibilization on the polylactide and poly(butylene adipate-<Emphasis Type="Italic">co</Emphasis>-terephthalate) blend films

Polylactide (PLA) films blended with 10 wt% poly(butylene adipate-co-terephthalate) (PBAT) were prepared by using a twin screw extruder in the presence of the nucleating agent of titanium dioxide (TiO₂) and the compatibilizers of toluene diisocyanate (TDI) and PLA-grafted-maleic anhydride (PLA-g-MA). The synergistic effect of the nucleation and compatibilization on the properties and crystallization behavior of the PLA/PBAT (PLB) films was explored. The results showed that the addition of TiO₂ significantly enhanced the tensile strength and the impact tensile resistance of the PLB films while slightly decreased its thermal stability. In addition, the compatibilizers of TDI and PLA-g-MA in the system not only affected the crystallinity and cold crystallization process of the PLB films, but also increased the mechanical properties of them due to the improvement of the interfacial interaction between PLA and PBAT revealed by the morphological measurement. The synergistic effects of the nucleating agent and the compatibilizer afforded the blend films with increased tensile strength and impact tensile toughness, improved cold crystallization property and χ _c.     

Effects of raster angle on the mechanical properties of PLA and Al/PLA composite part produced by fused deposition modeling

This paper studies the mechanical properties of polylactic acid (PLA) and aluminum fiber–reinforced PLA composite (Al/PLA) specimens fabricated by fused deposition modeling (FDM) process. The effect of raster angle (0°, 90°, 45°, 0°/90°, and ± 45°) on dynamic mechanical thermal property and tensile property of FDM‐printed PLA and Al/PLA has been studied. The results show reduced tensile strength and Young's modulus in Al/PLA composite specimen in comparison with pure PLA specimen. However, the elongation‐at‐break increases, which is due to Al fiber with the higher elasticity and lower tensile strength than PLA. The addition of Al fibers improves the dynamic mechanical thermal property of pure PLA because of the good interaction of the PLA matrix with the surrounding Al fibers. Raster angle plays an important role in FDM process. All specimens printed with 0° raster angle show highest tensile strength and dynamic mechanical properties, while specimens printed with 90° raster angle have the lowest values. Fractured surfaces indicate that the failure of the specimen with 0° raster angle is due to breaking of individual layers, while for 90° raster angle, specimen fails under separation of the adjacent raster layers.     

Effects of chain extender and uniaxial stretching on the properties of PLA/PPC/mica composites

Poly(lactic acid) (PLA)/poly(propylene carbonate) (PPC)/mica composites with different amount of chain extender (CE) were melt compounded and then processed via two routes (compression molding and uniaxial stretching) into sheets and films. The tensile, thermal, and oxygen barrier properties of all the samples were investigated. Tensile test showed that the tensile strength and elongation at break of all films were much higher than that of all sheets, especially for PLA/PPC/mica with 0.9‐wt% CE composite (CM₃(CE)_0.9) film. The crystallinity of all films increased significantly after uniaxial stretching of sheet samples. The Fourier transform infrared spectroscopy (FTIR) results proved the chemical reactions occurred between PLA/PPC and CE. Scanning electron microscope (SEM) analysis revealed that compatibility and interfacial adhesion of all samples were improved after adding mica and CE, and they were further enhanced after uniaxial stretching. The addition of CE was not favorable to improve the oxygen barrier performance of PLA/PPC/mica sheet samples. However, the oxygen barrier performance of film samples was significantly improved after uniaxial stretching. In particular, the CM₃(CE)_0.9 film had the lowest oxygen permeability coefficient (1.4 × 10^?15 cm³·cm/(cm²·s·Pa)), and this was the best oxygen barrier properties reported in the literature for PLA‐based composites, which was comparable with PA film. This study demonstrated the high efficiency of uniaxial stretching on improvement of properties of composites, which would promote the application of biodegradable polymers in oxygen sensitive food packaging.     

Influence of chemical surface modification of cellulose nanowhiskers on thermal,mechanical, and barrier properties of poly(lactide) based bionanocomposites

In the aim of producing fully organic bionanocomposite based on poly(lactide) (PLA), cellulose nanowhiskers (CNW) were grafted by n-octadecyl-isocyanate (CNW-ICN) applying an in situ surface grafting method. The compatibilizing effect of the long aliphatic grafted chain was investigated by thermal, mechanical and permeability analysis of solvent cast nanocomposite films. The grafted CNW-ICN could be successfully dispersed in the polymer matrix. The gained compatibility brought about a nucleating effect, decreasing the half time of isothermal crystallization from 25 min for the neat PLA to 8.4 min for the nanocomposite including 2.5 wt% CNW-ICN, e.g., tensile strength was improved by 10 MPa for the same 2.5 wt% CNW-ICN/PLA composite. Mechanical reinforcement was also effective in the rubbery state of PLA and increased the tensile modulus of the rubbery plateau providing thereby thermal resistance to the polymer. Oxygen barrier properties did not change significantly upon the inclusion of CNW-ICN, even when the quantity of CNW-ICN was increased to 15 wt%. More interestingly, the water vapour permeability of the CNW-ICN nanocomposite was always lower than the one of ungrafted CNW composites, which led to the conclusion that the hydrophobic surface graft and improved compatibility could counteract the effect of inclusion of hydrophilic structures in the matrix on water vapour transport. In conclusion, the surface grafting of CNW with isocyanates might be an easy and versatile tool for designing fully organic bionanocomposites with tailored properties.     

Plasticizing effects of epoxidized sun flower oil on biodegradable polylactide films: A comparative study

Polylactide (PLA) is one of the most promising materials among the renewable source-based biodegradable plastics. However, high inherent stiffness and brittleness of the pure PLA is often insufficient for wide range of engineering applications. One of the best ways to improve the processability, toughness and flexibility of PLA is to plasticize with epoxidized plant oils. In this work, epoxidized sun flower oil (ESFO) was incorporated into PLA matrix. The thermal, mechanical, biodegradation, optical transmission properties and fracture morphology of ESFO plasticized PLA were investigated to make a comparison with that of PLA plasticized by commercial epoxidized soya bean oil (ESO). Results show that a remarkable improvement of elongation at break was observed in the case of ESFO incorporated PLA. Although a slightly decrease the T _g of PLA was resulted from the plasticizing effects of ESFO, the thermal stability of the plasticized PLA was improved. On the other hand, the ESFO plasticized PLA showed a higher level of UV adsorption but a lower level of biodegradation ratio. After all, ESFO exhibited similar effects on the biodegradable PLA films to ESO, which is anticipated to be a good candidate for plasticizing biodegradable polymer materials.     

The morphological,mechanical, rheological,and thermal properties of PLA/PBAT blown films with chain extender

Biodegradable poly(lactic acid) (PLA)/poly(butylene adipate‐co‐terephthalate) (PBAT) blends and films were prepared using melt blending and blowing films technique in the presence of chain extender‐Joncryl ADR 4370F. The ADR contains epoxy functional groups and used as a compatibilizer. The morphological, mechanical, rheological, thermal, and crystalline properties of the PLA/PBAT/ADR blown films were studied. Scanning electron microscopy micrographs of the films revealed more ductile deformation with increasing PBAT content. The addition of PBAT enhanced the toughness of the PLA film. Tensile tests indicated that the elongation at break increased from 20.5% to 334.6% in the machine direction and from 7.1% to 715.9% in the transverse direction. The Young modulus increased from 2690.5 to 395.6 MPa in the machine direction and from 2623.5 to 154.0 MPa in the transverse direction. The sealing strength of 40/60/0.15 PLA/PBAT/ADR film was the highest among all the samples up to 9.4 N 15 mm⁻¹. These findings gave important implications for designing and manufacturing polymer packaging materials.     

Rosmarinic and Glycyrrhetinic Acid-Modified Layered Double Hydroxides as Functional Additives for Poly(Lactic Acid)/Poly(Butylene Succinate) Blends

Immobilizing natural antioxidant and biologically active molecules in layered double hydroxides (LDHs) is an excellent method to retain and release these substances in a controlled manner, as well as protect them from thermal and photochemical degradation. Herein, we describe the preparation of host–guest systems based on LDHs and rosmarinic and glycyrrhetinic acids, two molecules obtained from the extraction of herbs and licorice root, respectively, with antioxidant, antimicrobial, and anti-inflammatory properties. Intercalation between the lamellae of the mono-deprotonated anions of rosmarinic and glycyrrhetinic acid (RA and GA), alone or in the presence of an alkyl surfactant, allows for readily dispersible systems in biobased polymer matrices such as poly(lactic acid) (PLA), poly(butylene succinate) (PBS), and a 60/40 wt./wt. PLA/PBS blend. The composites based on the PLA/PBS blend showed better interphase compatibility than the neat blend, correlated with increased adhesion at the interface and a decreased dispersed phase size. In addition, we proved that the active species migrate slowly from thin films of the composite materials in a hydroalcoholic solvent, confirming the optimization of the release process. Finally, both host–guest systems and polymeric composites showed antioxidant capacity and, in the case of the PLA composite containing LDH-RA, excellent inhibitory capacity against E. coli and S. aureus.