Mechanical properties,surface morphology and failure mode of γ-ray irradiated blends of polypropylene and ethylene-vinyl acetate rubber

The effect of ⁶⁰Co γ-radiation on the mechanical properties, surface morphology and failure characteristics of blends of polypropylene [PP] and ethylene-vinyl acetate rubber [EVA] has been studied with specific reference to the effect of blend ratio, dynamic crosslinking of the rubber phase and absorbed radiation doses. Samples were subjected to radiation in the dose range of 1 to 100 Mrad in air at room temperature at the rate of 0·321 Mrad/h. Both chain scission and crosslinking occur simultaneously in the blend samples. PP and blends containing higher proportions of PP (≥50%) undergo predominant chain scission at lower doses (≤50 Mrad), which causes a drastic drop in tensile strength, followed by a levelling out at higher doses of 100 Mrad. EVA undergoes crosslinking at lower doses resulting in an increase in tensile strength in the dose range 1 to 10 Mrad followed by a decrease in the range 10–25 Mrad. Further increase in radiation dose has little effect on tensile strength. The effect of radiation on stress-strain behaviour, elongation at break, energy at rupture and hardness was also studied. The morphology of the irradiated surfaces after an absorbed dose of 100 Mrad has been examined by scanning electron microscopy (SEM). In order to understand the effect of γ-radiation on the failure mechanism, tensile failure surfaces of both unirradiated and irradiated samples have also been examined by SEM.     

In vitro hydrolytic degradation of poly(?-caprolactone) grafted dextran fibers and films

We studied the hydrolytic degradation of poly(?-caprolactone) grafted dextran (PGD) fibers and films (matrices) prepared by electrospinning and solvent evaporation methods, respectively. In vitro degradation and erosion experiments were carried out in phosphate buffered saline (pH 7.4 ± 0.1) at 37 ± 1 °C for 150 days. Changes in molecular weights and morphologies of the PGD matrices were monitored as a function of degradation time. The extent of degradation was measured by physical weight loss, scanning electron microscopic (SEM) observations, Fourier transform-infrared (FT-IR) spectroscopy, gel permeation chromatography (GPC) and differential scanning calorimetry (DSC). During the progress of hydrolysis, GPC chromatograms appeared bi modal for fibers and bi and trimodal for the films. The crystallization temperature (T_c) and heat of fusion were significantly increased in both matrices; this indicated preferential hydrolytic degradation in amorphous regions followed by cleavage-induced crystallization. The biodegradation rates were faster for the films (28%) than fibers (23%). After 150 days of degradation, the pH was steady at 5.8 ± 0.3 for fibers and 6.1 ± 0.3 for films. The faster degradation of the films could be probably due to autocatalysis in the interior of the films and the degraded oligomers are hard to diffuse out into the surrounding solution due to its compact physical geometry. Thus, our preliminary results about the degradation of matrices suggested that PGD nanofibers could be excellent matrices in tissue engineering over the films.     

Biodegradation of aliphatic polyesters soaked in deep seawaters and isolation of poly(?-caprolactone)-degrading bacteria

To investigate biodegradability of so-called biodegradable plastics in deep sea, degrading behavior of aliphatic polyesters poly(?-caprolactone) [PCL], poly(β-hydroxybutyrate/valerate) [PHB/V], and poly(butyrene succinate) [PBS] in deep seawaters were evaluated at Rausu, Toyama, and Kume, Japan. After 12 months of soaking in deep seawaters, PCL and PHB/V fibers became brittle or completely ruined. Although breaking strength of PBS fibers maintained approximately 95% of the initial values, for all 3 fibers, many pinholes and cracks were observed on the surfaces. These results imply that examined 3 aliphatic polyesters are degradable also at deep sea though the degradation rates would vary with the material structures. From the deep seawaters assessed, 5 PCL-degrading bacteria were isolated, which were found to belong to the genuses Pseudomonas, Alcanivorax, and Tenacibaculum, as assessed by phylogenetic analysis using 16S rRNA gene sequencing. It was also confirmed that all these bacteria degrade PCL fibers in vitro. In addition, these strains were found to prefer conditions of low temperature (4-10 °C) and high hydrostatic pressure.     

Physicochemical properties and hds activity of CoMo?P?Al2O3 catalysts

Porous structure, acidity and hds activity of the CoMo–P–Al₂O₃ catalysts have been studied. Phosphorus was introduced jointly with molybdenum. This method of phosphorus incorporation gave substantial diminution of surface area, moderate changes of acidity and decrease in hds activity for the catalysts with P₂O₅ content higher than 5 wt.%.

---

, CoMo–P–Al₂O₃. . , P₂O₅ 5 .%.

     

Thermal properties and combustibility of elastomer–protein composites

This article presents the test results of thermal properties and flammability of crosslinked nitrile rubber in the presence of zinc oxide or nano-zinc oxide containing waste keratin, using the test results obtained by means of a derivatograph, DSC, and oxygen index. The influence of modified montmorillonite (NanoBent) on selected properties of investigated elastomer–protein composites has also been studied. The composites' thermal stability and flammability depend on the method of composite preparation and the quantity of added keratin. The addition of waste keratin reduces the flammability of NBR–keratin composites.     

Crystal structure and high-pressure properties of γ-Mo2N determined by neutron powder diffraction and X-ray diffraction

We prepared samples of cubic γ-MoN_x (x∼0.5) by high-pressure-high-temperature synthesis. N atom site occupancies within the defect rock salt structure were determined from time-of-flight neutron diffraction and powder X-ray diffraction data by Rietveld analysis. The results show that N atoms occupy only octahedral sites within the structure. The semi-metallic compound is a superconductor, with determined by SQUID magnetometry. The compressibility of the material was determined by synchrotron X-ray diffraction measurements at high pressure in the diamond anvil cell. The vibrational density of states was studied by Raman scattering spectroscopy.     

Structure and electric properties of BaCe0.77 ? xZrxGd0.2Cu0.03O3 ? δ

In the present work, samples with the composition of BaCe_{0.77 − x} Zr _x Gd_0.2Cu_0.03O_{3 − δ} (x = 0, 0.1…0.7, 0.77) were synthesized according to the standard solid state technique. The effect of zirconium oxide on the phase character, structure, and conductivity was studied using the methods of X-ray diffraction analysis, scanning electron microscopy, and four-probe method, accordingly. Stability of these materials in the flow of carbon dioxide was studied. The results show that introduction of zirconium oxide leads to preservation of a single-phase system (x ≤ 0.6), a decrease in the grain size, and an increase in stability in the CO₂ atmosphere.     

Surface grafting of microfibrillated cellulose with poly(ε-caprolactone) - Synthesis and characterization

In cellulose nanocomposites, the surface of the nanocellulosic phase is critical with respect to nanocellulose dispersion, network formation and nanocomposite properties. Microfibrillated cellulose (MFC) has been grafted with poly(ε-caprolactone) (PCL), via ring-opening polymerization (ROP). This changes the surface characteristics of MFC and makes it possible to obtain a stable dispersion of MFC in a nonpolar solvent; it also improves MFC’s compatibility with PCL. The thermal behavior of MFC grafted with different amount of PCL has been investigated using thermal gravimetric analysis (TGA) and differential scanning calorimetry (DSC). From TGA measurements, the fraction of PCL in MFC-PCL samples was estimated to 16%, 19%, and 21%. The crystallization and melting behavior of free PCL and MFC-PCL were studied with DSC, and a significant difference was observed regarding melting points, crystallization temperature, degree of crystallinity, as well as the time required for crystallization.     

Synthesis and magnetic properties of nanocomposite Ni1?xCoxFe2O4–BaTiO3 fibers by organic gel-thermal decomposition process

Nanocomposites of ferrite and ferroelectric phases are attractive functional ceramic materials. In this work, the nanocomposite Ni_1−x Co _x Fe₂O₄–BaTiO₃(x = 0.2, 0.3, 0.4, 0.5) fibers with fine diameters of 3 ~ 7 μm and high aspect ratios were synthesized by the organic gel-thermal decomposition process from the raw materials of citric acid and metal salts. The structure, thermal decomposition process and morphologies of the gel precursors and the resultant fibers derived from thermal decomposition of the gel precursors were characterized by Fourier transform infrared spectroscopy, thermogravimetric differential thermal analysis, X-ray diffraction and scanning electron microscopy. The magnetic properties of the nanocomposite fibers were measured by vibrating sample magnetometer. The nanocomposite fibers of ferrite Ni_1−x Co _x Fe₂O₄ and perovskite BaTiO₃ are formed at the calcination temperature of 900 °C for 2 h. The average grain sizes of Ni_1−x Co _x Fe₂O₄ and BaTiO₃ in the nanocomposite fibers increase from about 15 nm to approximately 67 nm with the increasing calcination temperatures from 900 to 1,180 °C. The saturation magnetization of the nanocomposite Ni_1−x Co _x Fe₂O₄–BaTiO₃(x = 0.2, 0.3, 0.4, 0.5) fibers increases with the increase of grain sizes of Ni_1−x Co _x Fe₂O₄ and Co content, while the coercivity reaches a maximum value at the single-domain size of about 65 nm of Ni_0.5Co_0.5Fe₂O₄ obtained at the calcination temperature of 1,100 °C.     

Kinetic study of the oxidation of L-threonine by MnO4? ions

A self-catalytic effect attributed to Mn²⁺ ions was observed when studying the oxidation of L-threonine by permanganate ions. The process obeys the rate equation:

Super-exchange and Exchange-Enhanced Reactivity in Fe4S4-Mediated Activation of SAM by Radical SAM Enzymes?

[4Fe-4S]-dependent radical S-adenosylmethionine (SAM) proteins are a superfamily of oxidoreductases that can catalyze a series of challenging transformations using the common 5-dAdo radical intermediate. Although the structures and functions of radical SAM enzymes have been extensively studied, the electronic state-dependent reactions of the [4Fe-4S] clusters in these enzymes are still elusive. Herein we performed QM/MM calculations to elucidate the electronic state-dependent reactivity of the [4Fe-4S] cluster in pyruvate-formate lyase activating enzyme. Our calculations show that the electronic state-dependent SAM activation by the [4Fe-4S] clusters in radical SAM enzyme is determined by both the super-exchange and exchange-enhanced reactivities. The super-exchange coupling in the [4Fe-4S] cluster favors the antiferromagnetic coupling between two neighbouring pairs, which results in the \begin{document}$\alpha$\end{document}-electron rather than the \begin{document}$\beta$\end{document}-electron donation from the [4Fe-4S]\begin{document}$^{1+}$\end{document} cluster toward the SAM activation. Meanwhile, in the most favorable electronic state for the reductive cleavage of S\begin{document}$-$\end{document}C5\begin{document}$'$\end{document}, Fe4 would donate its \begin{document}$\alpha$\end{document}-electron to gain the maximum exchange interactions in the Fe4-block. Such super-exchange and exchange-enhanced reactivity could be the general principles for reactivities of [4Fe-4S] cluster in RS enzymes.     

Influence of Sn and Sn/Mg doping on structural features and visible absorption properties of α-Fe2O3 hematite

Pure, Sn-doped and Mg/Sn co-doped α-Fe₂O₃ hematite samples were synthesized by precipitation process. Fe₂O₃ is the most popular red mineral pigment which is used largely in traditional ceramics, tar and concrete. The compounds were characterized by powder X-ray diffraction (XRD), scanning transmission electronic microscopy (energy dispersive X-ray cartography), Mössbauer spectroscopy, magnetic investigations versus temperature and visible-NIR spectroscopy. Both ⁵⁷Fe and ¹¹⁹Sn Mössbauer analyses combined with rietveld XRD refinements are the ideal techniques to characterize tin-iron oxides. Hence, thanks to these techniques it was shown how the synthesis temperature influences directly the grain size and the dopants concentration limit which can be incorporated into the host hematite matrix. The stabilization of these tetravalent and divalent dopants into the hematite framework leads to reduce the crystal growth and to limit the (AF) ordering due to the formation of cationic vacancies. The study of the Morin magnetic transition emphasizes this demonstration. In a second part, the influence of the dopants incorporation on the material color was investigated in order to show which key parameters allow improving the red color saturation of iron oxides. In order to improve the red color of the hematites, it was shown that the introduction of cationic vacancies—limiting the octahedral distortion thanks to the interruption of the dissymmetric metal-metal orbital coupling—is the key point. Vacancies are created by Sn⁴⁺, doping for an increase of the introduced Sn⁴⁺ concentration; it acts to the detriment of the color saturation.     

Interface and properties of epoxy resin modified by elastomeric nano-particles

Epoxy resin has been widely used as structuralmaterials and adhesives in electronics, aerospace in-dustries and etc. for its impressive overall properties.However, epoxy network is brittle and notch sensitive,which restricts its application scope. As a re…     

Cytotoxicity and wound healing properties of PVA/ws-chitosan/glycerol hydrogels made by irradiation followed by freeze–thawing

Hydrogels based on poly(vinyl alcohol), water-soluble chitosan and glycerol made by irradiation followed by freeze–thawing were evaluated as wound dressing. MTT assay suggested that the extract of hydrogels was nontoxic towards L929 mouse fibroblasts. Compared to gauze dressing, the hydrogel can accelerate the healing process of full-thickness wounds in a rat model. Wounds treated with hydrogel healed at 11th day postoperatively and histological observation showed that mature epidermal architecture was formed. These indicate that it is a good wound dressing.     

Reduction of an amorphous NiO?Al2O3/SiO2 catalyst by different olefins and hydrogen

By static magnetic measurements it was found that the ability to reduction of an amorphous NiO–Al₂O₃/SiO₂ catalyst decreases in the order: but-2-eneshydrogen isobutene>but-1-ene>propeneethene. The reduction temperatures are significantly higher than the dimerization reaction temperatures.

---

, NiO–Al₂O₃/SiO₂ : -2>-1> . .

     

Encapsulation of α-tocopherol and β-carotene in concentrated oil-in-water beverage emulsions stabilized with whey protein isolate

The stabilization of flavor emulsions is a challenge for the industry of functional beverages. In this work, whey protein isolate was used as the stabilizing agent in concentrated orange oil-in-water emulsions. A 2³ factorial design was performed, varying the ratio of orange oil/water (30–60%), the concentration of whey protein (1–15%), and the concentration of the surfactant dioctyl sulfosuccinate sodium (0–100 mg L^?1). Analyses of surface tension, film formation, zeta potential, particle size, and turbidity were performed. Stable emulsions containing 60% of oil phase were prepared. β-Carotene and α-tocopherol were successfully encapsulated, without affecting the emulsion's stability.     

Magnetic and dielectric properties of YbFe2−xMnxO4 (0?x?1)

We have investigated the magnetic and dielectric properties of YbFe_2−xMn_xO₄ (0?x?1), which is an Fe-site-substituted system of new multiferroic oxides RFe₂O₄ (R=Y, Ho-Lu). X-ray diffraction measurements show that a solid solution is formed between YbFe₂O₄ (x=0) and YbFeMnO₄ (x=1) for 0?x?1, whereas only compounds with x=1 (i.e., RM₁M₂O₄; M₁ and M₂=trivalent and divalent cations, respectively) have been known for the Fe-site substitution in RFe₂O₄. The valence of the Mn ion is determined to be ∼2+, consistently with the suppression of low-temperature magnetization by the Mn substitution. The magnetic transition temperature (T_N) and the dielectric constant (ε′) decrease monotonically with increasing x. This result plausibly confirms that the magnetic and dielectric properties in oxides isostructural with RFe₂O₄ are governed by the electron transfer between Fe-site ions, unlike ordinary ferroelectrics and dielectrics, in which the ionic displacement plays a key role. The possibility for application is briefly discussed as well.     

Synthesis and electrochemical properties of LiNi0.85 ? x Co x Mn0.15O2 as cathode materials for lithium-ion batteries

LiNi_0.85−x Co _x Mn_0.15O₂ cathode material was prepared by a rheological phase reaction method with LiNO₃, M(NO₃)₂ 6H₂O (M = Ni, Co, Mn), and citric acid as starting materials. The mixture of reactants and a proper amount of water reacted to form a rheological precursor. The rheological precursor was pretreated in autoclaves and then calcined at 750 °C under flowing oxygen. All the samples have a typical layered structure with space group R3-m and good electrochemical performances. The cobalt content has a significant effect on the electrochemical performance for the materials. LiNi_0.65Co_0.20Mn_0.15O₂ exhibits the best electrochemical properties in the five compounds. It gives an initial discharge capacity of 173.6mAhg⁻¹ (50mA g⁻¹, 3.0−4.3V), and the capacity rention after 50 cycles is 90.6%. This method is simple and effective for preparing cathode materials for lithium-ion batteries.     

Effect of oxygen non-stoichiometry on the structural and magnetotransport properties of LaMn0.85Cr0.15O3+δ

Thermogravimetry, X-ray diffraction (XRD), d.c. magnetization, high-temperature susceptibility and electrical resistivity measurements were performed for LaMn_0.85Cr_0.15O_3+δ perovskites with accurate control of the oxygen content (0?δ?0.11). For 0?δ<0.09, three orthorhombic structures (Pnma) are found: for 0?δ<0.045, the O′ phase (b/√2<c<a), for 0.045?δ<0.06, the O″ (b/√2<a<c) and for 0.06?δ<0.09, the O^? (a<b/√2<c). For 0.09?δ?0.11, a rhombohedral symmetry coexists with O^? in a biphasic field. Magnetic measurements revealed the ferromagnetic interactions (FM) character of the Mn³⁺-O-Cr³⁺ interaction, but also the intricate magnetic phase diagram due to the presence of multiple interactions (Mn^3+,4+-O-Mn^3+,4+, Cr³⁺-O-Mn³⁺, etc.). The comparison of the results for LaMn_0.85Cr_0.15O_3+δ with those of LaMn_0.9Cr_0.1O_3+δ allows discuss the role of Cr³⁺ on the structural, magnetic and magnetotransport properties of the LaMn_1−xCr_xO_3+δ perovskites.