Mechanistic investigation, kinetic modeling and analysis parameters of poly(3-hexylthiophene) degradation to fullerenes

Thermal degradation of Poly (3-hexylthiopene) (P3HT) was studied under nitrogen environment. Kinetic parameters of thermal degradation were determined using Vyazovkin model free method and model fitting method. Vyazovkin model free kinetic analysis is carried out to understand the variation of activation energy (E_α) required for degradation of polymer with conversion (α). Various reaction models have been tested for probable reaction mechanism using hybrid genetic algorithm (HGA). Diffusion model and nucleation & growth with n = 2/3 has prominent role in thermal decomposition of P3HT. A plausible degradation route is proposed based on the experimental details acquired from gas chromatography (GC), Raman spectroscopy, FTIR spectroscopy, powder X-ray diffractometry (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Degradation of P3HT starts at around 195 °C with release of lighter units like CS. Further increase in the temperature results in detachment of the hexyl chain from P3HT and the residue obtained at 1050 °C contains fullerenes mixed with amorphous carbon.     

Effect of thermal annealing on the microstructure of P3HT thin film investigated by RAIR spectroscopy

The influence of thermal annealing on the structural ordering and orientation rearrangement of as cast P3HT thin film (<100 nm) has been studied by reflection absorption infrared spectroscopy (RAIR). In order to erase the effect of temperature on the spectral intensity, two thermal procedures have been used to investigate the annealing-induced structural change of P3HT thin film. One is the continuous heating mode, in which the RIAR spectra were in situ collected during the heating process. The other is the stepwise heating mode, that is the isothermal annealing, and the spectra were ex situ collected at room temperature after the thermal treatment. It is found that thermal annealing can enhance the π–π interaction in P3HT crystal domain, whereas the improvement on the degree of crystallinity is not so obviously. Meanwhile, our results suggest that annealing-induced structural rearrangement on π–π stacking is irreversible, whereas the change on hexyl side chain packing is reversible.     

High‐resolution MALDI‐TOF MS study on analysis of low‐molecular‐weight products from photo‐oxidation of poly(3‐hexylthiophene)

High‐resolution matrix‐assisted laser desorption/ionization (MALDI) time‐of‐flight mass spectrometry (TOF MS) was used for the analysis of the low‐molecular‐weight products from the photo‐oxidation of poly(3‐hexylthiophene) (P3HT) in solution and thin film. Eight new peak series were observed in the low‐mass range of the mass spectra of the products degraded in solution, and the formulas of the eight components were determined from the accurate mass. From SEC/MALDI‐TOF MS, two components were identified as the degraded products, and the other six components were derived from the fragmentation of the degraded products during the MALDI process. A mechanism for the formation of these components was proposed on the basis of the results of MALDI‐TOF MS. For the thin film degradation, a part of products in the solution degradation were observed, which supports that the oxidation of P3HT in solution and thin film proceeded in the same mechanism. This study shows that high‐resolution MALDI‐TOF MS is effective for the analysis of the low‐molecular‐weight products from P3HT photo‐oxidation and expected to be feasible for the degradation analyses of other polymers. Copyright © 2015 John Wiley & Sons, Ltd.     

Influence of the microstructure on the photooxidative degradation of poly(3-hexylthiophene)

The influence of the microstructure of poly(3-hexylthiophene) (P3HT) on its photodegradation upon exposure to UV-visible light was studied. High-regioregular (>98%) and low-regioregular (<95%) P3HTs with different molecular weights, dispersities and purities were submitted to irradiation under accelerated artificial ageing conditions. While the molecular weight had no effect on the photodegradation rate, a linear relationship was observed between the photodegradation rate and the regioregularity. The higher photo-instability of low-regioregular P3HTs, which have low crystalline phase content, could be due to the fact that the radical chain oxidation occurs predominantly in the amorphous phase of the polymer. Low-regioregular P3HTs also have a higher number of impurities, especially Fe residues, which are well known for their photocatalytic effect. The results also show that, at low concentrations, oxidation products are able to quench the singlet state of P3HT by acting as electron traps, and that the shortest wavelengths of solar light are the most harmful. Finally, the photooxidation of P3HT leads to the formation of low-molecular-weight carboxylic acids that can easily diffuse and migrate out of low-regioregular P3HT thin films. These results are therefore relevant to the preparation, storage and lifetimes of P3HT-based organic solar cells.     

Thermal stability of P3HT and P3HT:PCBM blends in the molten state

The thermal stability of poly(3-hexylthiophene) (P3HT) in its molten state was investigated in air and nitrogen atmospheres under no illumination conditions, with the aim of testing the feasibility of processing it using polymer melt techniques. A large set of different experimental characterization techniques was used including thermogravimetric analysis (TGA), rotational rheometry, infrared spectroscopy (FTIR-ATR), proton nuclear magnetic resonance spectroscopy (¹H-NMR), gel permeation chromatography (GPC), UV-Vis and fluorescence spectroscopy. The results obtained strongly suggest that the processing of P3HT in its molten state is possible, without noticeable degradation, if carried out under nitrogen atmosphere and if the processing (residence) times are relatively short. Conversely, as expected, in a normal air atmosphere P3HT degrades rapidly at temperatures above its melting point. The effect of PCBM on the thermal stability of P3HT:PCBM blends in the molten state was also studied using TGA, and in air atmosphere PCBM is shown to delay oxidation.     

退火处理提高P3HT:PCBM聚合物太阳能电池光伏性能

利用旋转涂膜方法制备了以P3HT:PCBM为有源层的聚合物太阳能电池, 器件结构为ITO/PEDOT:PSS/P3HT:PCBM/Al(氧化铟锡导电玻璃/聚二氧乙基噻吩:聚对苯乙烯磺酸/聚三已基噻酚:富勒烯衍生物/铝),研究了退火温度对聚合物太阳能电池性能的影响. 实验发现: 聚合物薄膜经过120 °C退火10 min处理后, 开路电压(V_oc)达到0.64 V, 短路电流密度(J_sc)为10.25 mA·cm^-2, 填充因子(FF) 38.1%, 光电转换效率(PCE)达到2.00%. 为了讨论其内在机制, 对不同退火条件下聚合物薄膜进行了各种表征. 从紫外-可见吸收光谱中发现, 退火处理使P3HT在可见光范围内吸收加强且吸收峰展宽, 特别是在560和610 nm处的吸收强度明显增大; X射线衍射(XRD)结果表明, 120 °C退火后P3HT在(100)晶面上的衍射强度是未退火薄膜的2.8倍, 有利于光生载流子的输运; 原子力显微镜(AFM)研究结果表明, 退火显著增大了P3HT与PCBM的相分离程度, 提高了激子解离的几率; 傅里叶变换红外(FTIR)光谱验证了退火并没有引起聚合物材料物性的变化.     

Co-microencapsulate of ammonium polyphosphate and pentaerythritol and kinetics of its thermal degradation

Co-microencapsulated ammonium polyphosphate (APP) and pentaerythritol (PER) (M (A&P)) is prepared using melamine-formaldehyde (MF) resin by in situ polymerization method, and characterized by Energy dispersive spectrometer (EDS) and Fourier transform infrared (FTIR) spectra. Thermal stability of M (A&P) has been analyzed and compared with APP/PER mixture. In air atmosphere, the mass loss of M (A&P) at different heating rates was investigated using TGA. The kinetics of thermal degradation and activation energy was described using Flynn-Wall-Ozawa and Kissinger methods. It showed that there were two degradation stages. Expanded carbon structure with honeycomb was formed in the first stage between 200 and 450 °C. The second stage was the oxidation of carbon with E_a as high as 151.7 kJ/mol, so the expanded carbon had a good thermal stability. The reaction order of thermal degradation was found to be 0.935, so the mechanism of M (A&P) thermal degradation was controlled by the process of random nuclear formation and growth.     

Impact of Alkoxyl Tail of Fullerene Dyad Acceptor on Crystalline Microstructure for Efficient External Treatment-free Polymer Solar Cells with Poly(3-hexylthiophene) as Donor

A series of tri(alkoxyl)benzene-fullerene dyads(PCBB-Cn, n=4, 6, 8, 10, 12) with varied tri(alkoxyl) chain lengths was designed, synthesized and used as acceptor materials in polymer solar cells(PSCs). The five fullerene dyads possess similar absorption spectra in dilute solution, decreased glass-transition temperature(T_g) and gradually elevated lowest unoccupied molecular orbital(LUMO) energy levels from -3.87 eV to -3.73 eV with the increase of the alkoxy chain length. In the fabrication of PSCs with poly(3-hexylthiophene)(P3HT) as donor and the fullerene dyads as acceptor, PCBB-Cn with longer tri(alkoxyl) chains and lower T_g can induce crystalline structure of P3HT during spin-coating the photoactive layer at room temperature and form nanoscale phase separated interpenetrating network of P3HT:PCBB-Cn blend films, which results in the improvement of photovoltaic performance of PSCs. A power conversion efficiency of 3.03% for the PSCs based on P3HT:PCBB-C10 was obtained without thermal annealing or solvent annealing. The thermal and solvent annealing-free fabrication using the fullerene dyads as acceptor is very important for the roll to roll production of PSCs with flexible large area.     

Performance enhancement of CdS nanorod arrays/P3HT hybrid solar cells via N719 dye interface modification

Improved hybrid solar cells consisting of vertical aligned cadmium sulfide (CdS) nanorod arrays and interpenetrating polythiophene (P3HT) have been achieved via modification of CdS nanorod surface by using conjugated N719 dye. The complete infiltration of P3HT between CdS nanorods interspacing was verified by scanning electron microscopy. By employing absorption and photoluminescence spectra, and current-voltage characterization the interaction between N719 molecules and CdS nanorods/P3HT interface was explored, and the role of N719 dye on the improvement of device performance was discussed.     

Synthesis of all‐conjugated poly(3‐hexylthiophene)‐block‐ poly(3‐(4′‐(3″,7″‐dimethyloctyloxy)‐3′‐pyridinyl)thiophene) and its blend for photovoltaic applications

New all‐conjugated block copolythiophene, poly(3‐hexylthiophene)‐block‐poly(3‐(4′‐(3″,7″‐dimethyloctyloxy)‐3′‐pyridinyl)thiophene) (P3HT‐b‐P3PyT) was successfully prepared by Grignard metathesis polymerization. The supramolecular interaction between [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) and P3PyT was proposed to control the aggregated size of PCBM and long‐term thermal stability of the photovoltaic cell, as evidenced by differential scanning calorimetry (DSC), transmission electron microscopy (TEM), and optical microscopy. The effect of different solvents on the electronic and optoelectronic properties was studied, including chloroform (CL), dichlorobenzene (DCB), and mixed solvent of CL/DCB. The optimized bulk heterojunction solar cell devices using the P3HT‐b‐P3PyT/PCBM blend showed a power conversion efficiency of 2.12%, comparable to that of P3HT/PCBM device despite the fact that former had a lower crystallinity or absorption coefficient. Furthermore, P3HT‐b‐P3PyT could be also used as a surfactant to enhance the long‐term thermal stability of P3HT/PCBM‐based solar cells by limiting the aggregated size of PCBM. This study represents a new supramolecular approach to design all‐conjugated block copolymers for high‐performance photovoltaic devices. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Studies of degradation behaviors of poly (3‐hexylthiophene) layers by X‐ray photoelectron spectroscopy

Degradation behaviors of poly(3‐hexylthiophene‐2,5‐diyl) (P3HT) layers on NiO in the presence of H₂O at ambient pressure and dark conditions were studied using X‐ray photoelectron spectroscopy (XPS). Upon H₂O exposure at 120 °C, partial oxidation of P3HT together with molecular water incorporation, but with the maintained local ring‐structure, were deduced by XPS. Valence band spectra of XPS evidenced that the partial oxidation of P3HT local structure could alter π‐conjugation systems of P3HT layers, forming additional electronic states close to its original highest occupied molecular orbital. For comparison, P3HT surface was also exposed to O₂, and no change in the S 2p and C 1s spectra was found by O₂ exposure at 120 °C, implying that H₂O plays a major role at the initial stage of P3HT oxidation. Copyright © 2014 John Wiley & Sons, Ltd.     

退火处理提高P3HT:PCBM聚合物太阳能电池光伏性能

利用旋转涂膜方法制备了以P3HT:PCBM为有源层的聚合物太阳能电池, 器件结构为ITO/PEDOT:PSS/P3HT:PCBM/Al(氧化铟锡导电玻璃/聚二氧乙基噻吩:聚对苯乙烯磺酸/聚三已基噻酚:富勒烯衍生物/铝),研究了退火温度对聚合物太阳能电池性能的影响. 实验发现: 聚合物薄膜经过120 °C退火10 min处理后, 开路电压(V_oc)达到0.64 V, 短路电流密度(J_sc)为10.25 mA·cm^-2, 填充因子(FF) 38.1%, 光电转换效率(PCE)达到2.00%. 为了讨论其内在机制, 对不同退火条件下聚合物薄膜进行了各种表征. 从紫外-可见吸收光谱中发现, 退火处理使P3HT在可见光范围内吸收加强且吸收峰展宽, 特别是在560和610 nm处的吸收强度明显增大; X射线衍射(XRD)结果表明, 120 °C退火后P3HT在(100)晶面上的衍射强度是未退火薄膜的2.8倍, 有利于光生载流子的输运; 原子力显微镜(AFM)研究结果表明, 退火显著增大了P3HT与PCBM的相分离程度, 提高了激子解离的几率; 傅里叶变换红外(FTIR)光谱验证了退火并没有引起聚合物材料物性的变化.     

聚3-己基噻吩的制备及其荧光轨迹的研究

本文以3-己基噻吩为单体,无水FeCl3为氧化剂,在四氢呋喃(THF)中浓缩结晶制备了聚3-己基噻吩(P3HT),通过红外光谱、GPC、XRD和1H NMR表征其结构,测定了经THF浓缩前后P3HT的电流-电压曲线,并采用单分子光谱技术得到了其在介孔纳米TiO2基底上的荧光强度轨迹。结果表明,通过THF浓缩结晶能提高P3HT的相对分子量和其太阳能电池的能量转化效率,并且单分子P3HT/TiO2体系间界面电子的转移是不均一的,不但随着分子的不同而不同,而且还随着时间的不同而不同,其自相关函数呈非指数的衰减。     

Poly(3‐hexylthiophene)‐b‐poly(3‐cyclohexylthiophene): Synthesis,microphase separation,thin film transistors,and photovoltaic applications

We report the synthesis, characterization, microphase separation, field‐effect charge transport, and photovoltaic properties of regioregular poly(3‐hexylthiophene)‐b‐poly(3‐cyclohexylthiophene) (P3HT‐b‐P3cHT). Two compositions of P3HT‐b‐P3cHT (HcH63 and HcH77) were synthesized with weight‐average molecular weights of 155,500 and 210,800 and polydispersity indices of 1.45 and 1.57, respectively. Solvent‐casted HcH77 was found to self‐assemble into nanowires with a width of 12.5 ± 0.9 nm and aspect ratios of 50–120, as observed by TEM imaging. HcH77 and HcH63 annealed 280 °C were observed by small angle X‐ray scattering (SAXS) and wide angle X‐ray scattering (WAXS) to be microphase‐separated with characteristic length scales of 17.0–21.7 nm. The microphase‐separated domains were shown to be crystalline with interlayer backbone (100) d‐spacings of 1.69 and 1.40 nm, which correspond to the P3HT and P3cHT blocks, respectively. Field‐effect transistors fabricated from P3HT‐b‐P3cHT thin films showed a mobility of holes (0.0019 cm²/Vs) which is independent of thermal annealing. Bulk heterojunction solar cells based on HcH77/fullerene (PC₇₁BM) blend thin films had a maximum power conversion efficiency of 2.45% under 100 mW/cm² AM1.5 solar illumination in air. These results demonstrate that all‐conjugated block copolymers are suitable semiconductors for applications in field‐effect transistors and bulk heterojunction solar cells. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 614–626, 2010     

Synthesis of new nanocrystal-polymer nanocomposite as the electron acceptor in polymer bulk heterojunction solar cells

A hydroxyl-coated CdSe nanocrystal (CdSe-OH) and a CdSe-polymer nanocomposite were synthesized and used as the electron acceptors in polymer solar cells (PSCs). The CdSe-polymer composite was prepared via atom transfer radical polymerization (ATRP) of N-vinylcarbazole on functionalized CdSe quantum dots. Physical properties and photovoltaic characteristics of the CdSe-poly(N-vinylcarbazole) (CdSe-PVK) nanocomposite have been investigated. Thermogravimetric analysis (TGA) results displayed higher thermal stability for CdSe-PVK nanohybrid in comparison with the linear-type PVK polymer. Differential scanning calorimetry (DSC) studies indicated that CdSe-PVK had a lower glass-transition temperature (T_g) in comparison with PVK due to the branch effect of the star-shaped polymer hybrid. Cyclic voltammetric (CV) measurements were performed to obtain HOMO and LUMO values of PVK and CdSe-PVK. TEM and SEM micrographs exhibited CdSe nanoparticles were well coated with PVK polymer. Both CdSe-OH and CdSe-PVK were blended with poly(3-hexylthiophene) (P3HT) and used as the active layer in bulk heterojunction solar cells. Polymer solar cell based on CdSe-PVK as acceptor revealed that the photovoltaic properties can be significantly improved when PVK polymer chains were grafted on surfaces of CdSe nanocrystals. In comparison with the P3HT:CdSe-OH system, PSC based on P3HT:CdSe-PVK showed an improved power conversion efficiency (0.02% vs. 0.001%). Film topography studied by AFM further confirmed the better device performance was due to the enhanced compatibility between P3HT and CdSe-PVK.     

Photo- and thermo-oxidation of poly(p-phenylene-vinylene) and phenylene-vinylene oligomer

This paper reports a study of the photo- and thermo-degradation of poly(p-phenylene-vinylene)-type (PPVs) materials, including a five-ring n-octyloxy substituted phenylene-vinylene oligomer (Ooct-OPV5) and poly(p-phenylene-vinylene) (PPV). The modifications in the chemical structure of the thin films submitted to UV-visible light irradiation and thermal oxidation were analysed with infrared spectroscopy, and the oxidation products were identified by derivatisation reactions. Results showed that the photochemical and thermal behaviour of the Ooct-OPV5 oligomer was similar to that of MDMO-PPV (poly[2-methoxy-5-(3′,7′-dimethyloctyloxy)-1,4-phenylenevinylene), which is a polymer used in organic solar cells. Additionally, the identification of the products resulting from the oxidation of the vinylene bonds was simpler in Ooct-OPV5 and PPV compared to MDMO-PPV In contrast, the oxidation mechanisms of PPV, which has no ether substituent, and MDMO-PPV are not identical; the disappearance of the double bonds in PPV does not involve the formation of aromatic ketones. It was also shown that the absence of ether substituents does not decrease the rate of photo-oxidation of PPV compared to MDMO-PPV. Finally, as the same mechanisms proposed for Ooct-OPV5 and PPV occur under both photo- and thermo-oxidative conditions of ageing, this confirms that singlet oxygen does not play a decisive role in the photo-oxidation of PPVs.     

Stable and Low‐Cost Mesoscopic CH3NH3PbI2Br Perovskite Solar Cells by using a Thin Poly(3‐hexylthiophene) Layer as a Hole Transporter

Mesoscopic perovskite solar cells using stable CH₃NH₃PbI₂Br as a light absorber and low‐cost poly(3‐hexylthiophene) (P3HT) as hole‐transporting layer were fabricated, and a power conversion efficiency of 6.64 % was achieved. The partial substitution of iodine with bromine in the perovskite led to remarkably prolonged charge carrier lifetime. Meanwhile, the replacement of conventional thick spiro‐MeOTAD layer with a thin P3HT layer has significantly reduced the fabrication cost. The solar cells retained their photovoltaic performance well when they were exposed to air without any encapsulation, presenting a favorable stability. The combination of CH₃NH₃PbI₂Br and P3HT may render a practical and cost‐effective solid‐state photovoltaic system. The superior stability of CH₃NH₃PbI₂Br is also promising for other photoconversion applications.     

Electronic Structure Effect of Polythiophene Derivatives and Nano N-Zn-Ag/TiO2 on Performance of Organic Thin Film Solar Cell

Nanocrystal N-Zn-Ag/TiO₂ powders were prepared with N-Zn/TiO₂ by photo deposition method. A series of pure polymers P3HT[poly(3-hexylthiophene)], P3OT[poly(3-octylthiophene)], P3DT[poly(3-decylthiophene)] and P3DDT[poly(3-dodecylthiophene)], was synthesized, which were used to synthesize p-n type semiconductor materials P3HT/N-Zn-Ag-TiO₂, P3OT/N-Zn-Ag-TiO₂, P3DT/N-Zn-Ag-TiO₂ and P3DDT/N-Zn-Ag-TiO₂ by in situ che-mical method. X-Ray diffraction(XRD) and infrared(IR) spectroscopy showed the structure of the polymers and complexes. Ultraviolet-visible(UV-Vis) spectra and cyclic voltammograms(CV) showed the optical and electronic performance of the polymers and complexes. Two new single and double organic thin film heterojunction solar cells were prepared with the above mentioned synthesized powders as raw materials. Current-voltage(I-V) measurements indicate that the conversion efficiency of the single organic thin film heterojunction solar cell is higher than that of the double organic thin film heterojunction solar cells. Single organic thin film heterojunction solar cells based on P3DT/N-Zn-Ag-TiO₂ can get a photoelectric conversion efficiency of 0.0408%. The performance of electronic transform between electron donor and acceptor on organic thin film solar cells was researched.     

P3HT修饰一维有序壳核式CdS/ZnO纳米棒阵列复合膜的光电化学性能

采用电化学方法在铟锡氧化物(ITO)导电玻璃上制备了高度有序的ZnO纳米棒阵列, 在ZnO纳米棒阵列上先后电化学沉积CdS纳米晶膜及聚3-己基噻吩(P3HT)薄膜得到P3HT修饰的一维有序壳核式CdS/ZnO纳米阵列结构, 并通过扫描电镜(SEM)、透射电镜(TEM)、X射线衍射(XRD)、能量散射X射线(EDX)等表征手段证实了该结构的形成. 以此纳米结构薄膜为光阳极组装新型半导体敏化太阳电池, 研究了CdS纳米晶膜的厚度和P3HT薄膜的沉积对电池光伏性能的影响, 初步探讨了电荷在电池结构中的传输机理, 结果表明, CdS纳米晶膜和P3HT薄膜的沉积有效地拓宽了光阳极的光吸收范围, 实验中电池的光电转换效率最高达到1.08%.     

Structure and thermochromic solid-state phase transition of poly (3-alkylthiophene)

In order to clarify the structural changes that occur in the thermochromic phase transition of poly (3-dodecylthiophene) [P3DT] and poly (3-hexylthiophene) [P3HT], the temperature dependence of x-ray diffraction and Fourier transform infrared spectra was measured. (1) Orthogonal unit-cell parameters were determined at room temperature: a=25.83 Å, b=7.75 Å, c (fiber axis)=7.77 Å for P3DT and a=16.63 Å, b=7.75 Å, and c=7.77 Å for P3HT. A large variation of the a-axis length between P3DT and P3HT indicates the extended trans conformation for the alkyl side chains which are oriented along the lateral a-axis direction. (2) The interplanar spacing, intensity, and integral width of the x-ray (h00) and (00l) reflections were found to change drastically in the transition region. (3) Polarized infrared measurements at high temperature revealed a marked increase of the gauche band intensity for the alkyl side group modes followed by a decrease in the band intensity of the thiophene ring modes. (4) The layer reflections of the x-ray fiber diagram become diffuse at high temperatures, indicating that the transition occurs in a liquidcrystalline manner with the orientation of the main chain axes preserved but with almost no axial correlation between the neighboring main chains. These results provide experimental support for the structural model proposed earlier: as the temperature increases, the trans-type side chains begin to disorder by introduction of gauche bonds. This disordering disrupts the regularity of the main chain conformation and decreases the effective length of the polythiophene conjugated system.