Low percolation conductive graphite flakes-filled poly(urethane-imide) composites with high thermal stability via imidization self-foaming structure

In the study, the conductive graphite flakes filled poly(urethane-imide) composites (PUI/GFs) with high performance were constructed by the thermal imidization self-foaming reaction. It was found that the foaming action could promote the redistribution of GFs during curing process and the formation of stable linear conductive pathways. The percolation threshold of PUI/GFs composites was lowered from 1.26 wt% (2000 mesh GFs) or 0.86 wt% (1000 mesh GFs) to 0.79 wt% (500 mesh GFs), which were relatively low percolation thresholds for polymer/GFs composites so far. When the content of 500 mesh GFs was 4.0 wt%, the electrical conductivity of the composite was as high as 3.96 × 10^?1 S/m. Also, a poly(urethane-imide) (PUI) matrix with excellent thermal stability (T_d10%: 334.97 °C) and mechanical properties (elongation at break: 324.52%, tensile strength: 15.88 MPa) was obtained by introducing the rigid aromatic heterocycle into the polyurethane (PU) hard segments. Moreover, the zero temperature coefficient of resistivity for the composites was observed at the temperature range from 30 °C to 200 °C. Consequently, PUI/GFs composites may provide the novel strategy for considerable conductive materials with high thermal stability in electrical conductivity.     

Optical and mechanical properties of polyurethane/surface-modified nanocrystalline cellulose composites

in order to improve the optical and mechanical performances of waterborne polyurethane （WPU）, nanocrystalline cellulose （NCC）/WPU composites were synthesized in this study. NCC （prepared by acid hydrolysis of cotton fiber） was modified by （3-aminopropyl）triethoxysilane （APTES） to enhance its compatibility with WPU, and the surface-modified NCC was characterized by grafting ratio, crystallinity and contact angle （CA）. NCC/WPU composites were examined by scanning electron microscopy （SEM）, X-ray powder diffraction （XRD） and thermogravimetric analysis （TG）. The anti-yellowing property, specular gloss, pencil hardness, and abrasion resistance of NCC/WPU composites were investigated by the methods of Chinese National Standards GB/T 23999-2009, GB/T 9754-2007, GB/T 6739-2006 and GB/T 1768-2006, respectively. The results showed that the grafting ratio of NCC modified by 6% APTES was 36.01% and the crystallinity of modified NCC was decreased with the enhancement of APTES. CA of the modified NCC was decreased by 28.8% and the nanoparticles were homogeneously dispersed in the WPU matrix. The XRD patterns of the NCC/WPU composites were relatively steady, while the thermal stability of the composites was enhanced by 6.7% with 1.0 wt% modified NCC. Modified NCC affected the specular gloss of NCC/WPU composites more obviously than the anti-yellowing property. The pencil hardness of NCC/WPU composites was increased from 2H to 4H by addition of NCC and the abrasion resistance of the composites was enhanced significantly. In general, NCC/WPU composites showed significant improvements in the optical and mechanical performances.     

Filler network structure in graphene nanoplatelet (GNP)-filled polymethyl methacrylate (PMMA) composites: From thermorheology to electrically and thermally conductive properties

In this work, graphene nanoplatelet (GNP) filled polymethyl methacrylate (PMMA) composites were prepared using solution method via a specially designed route and relatively high thermal conductivities of the composites were achieved at a low GNP loading. The effect of GNP content on rheological behavior, thermal and electrical conductivity of the composites was intensively investigated. Thermorheological complexity was displayed at elevated GNP loading, and the rheological percolation threshold of GNP in PMMA decreased from 7.96 wt% at 220 °C to 4.02 wt% at 260 °C according to Winter-Chambon method, suggesting that GNP was more likely to form a seepage network at higher temperature. The DMTA results showed that the increase in moduli of the composites should be ascribed to the formation of the GNP-GNP network structure. The electrical conductivity of the composites underwent a sudden jump by seven orders of magnitude, which also indicated the formation of a GNP conductive pathway in the matrix with an electrical percolation threshold of 2–4 wt%. The results of transient temperature measurement were in good consistent with the thermal conductivity versus GNP loading, which was compared with various thermal conduction models with a modified Agari model presenting an acceptable evaluation of the dispersion status of GNP in the matrix. The experimental electrical and thermal conductivities as a function of GNP content could well be interpreted by the filler network structure as observed in morphological studies.     

Thermal behavior,dynamic mechanical properties and rheological properties of poly(butylene succinate) composites filled with nanometer calcium carbonate

PBS/nano-CaCO₃ composites with various nano-CaCO₃ weight fractions were prepared by melt blending. The thermal behavior, dynamic mechanical properties and rheological properties of the composites were investigated. DSC measurements revealed that the nano-CaCO₃ particles had little influence on the crystallization and melting behavior of PBS. Thermogravimetric analysis showed that the introduction of nano-CaCO₃ tended to improve the thermal stability of PBS. Dynamic mechanical analysis showed that the G′ and G″ of the PBS/nano-CaCO₃ composites were improved significantly when the nano-CaCO₃ content was not more than 3wt%, while the G′ and G″ were mainly decided by the PBS matrix when the nano-CaCO₃ content exceeded 3wt%. Rheological results showed that G′ < G″ over the frequency range, illustrating the viscous behavior of the samples. The η* of all the samples remained almost constant when the frequency was not more than 0.25 rad/s, which showed the characteristic of a Newtonian fluid. A strong shear thinning effect was observed for all the samples when the frequency exceeded 0.25 rad/s. Furthermore, the microstructure and the relaxation mechanism of the PBS/nano-CaCO₃ composites mainly depended on the PBS matrix.     

Improving hydrophobicity and compatibility between kenaf fiber and polymer composite by surface treatment with inorganic nanoparticles

Compatibility of natural fiber with hydrophobic matrix is a herculean task in literature works. Surface treatment is a well-known approach for increasing the strength of interfacial adhesion between fibres and polymer matrices. Therefore, this study aims to examine the impact of surface treatment with zinc oxide nanoparticles (ZnONPs) in improving hydrophobicity of kenaf fiber (KF) to enhance the compatibility between KF and polymer matrix. In this study, KF reinforced unsaturated polyester composites (KF/UPE) were fabricated by the hand lay-up method with varying fiber loadings (wt %) of 10 20, 30, and 40. KF were treated with five different contents of ZnONPs (1% to 5 wt%) to make UPE/KF-ZnONPs composites. The composites were studied in terms of wetting response (contact angle measure and water absorption), mechanical properties, chemical structure (FTIR), crystalline structure (XRD), and surface morphology (SEM, AFM). The investigational findings indicate that the composite samples incorporating ZnONPs exhibit optimum hydrophobicity and mechanical properties, as they possessed a higher contact angle than the untreated KF composite. The optimum content of ZnONPs was found to be 2 wt%. Regarding water absorption, the untreated UPE/KF composites absorbed more water than the treated UPE/KF-ZnONPs composites. SEM images showed changes in the morphology of the KF, while FTIR analysis proved the presence of ZnONPs functional groups in the UPE/KF composites. AFM images revealed that the ZnONPs could actively produce nanolevel roughness, advantageous to the hydrophobic characteristics.     

Epoxy nanocomposites with high thermal conductivity and low loss factor: Realize 3D thermal conductivity network at low content through core-shell structure and micro-nano technology

Dielectric polymers with high thermal conductivity are very promising in the fields of aerospace and electronic device packaging. However, composites with excellent dielectric properties usually have low thermal conductivity. It is usually to fill the polymer with thermal conductivity particles to improve the thermal conductivity, but the high content of filler often reduces the mechanical properties of the polymer. In this paper, the traditional insulating polymer epoxy resin was used as the matrix, by covering the surface of silicon carbide with graphene to form a core-shell structure and co-filled with nano diamonds to achieve the preparation of high-performance epoxy resin at low content. The results showed that at the filling content of 30 wt%, the thermal conductivity of epoxy nanocomposites showed a dramatic thermal conductivity enhancement of 1263%, the energy storage modulus increased by 1.1 GPa, and the dielectric loss remained unchanged at 50 Hz. The advantages of the composite are the structural design and surface modification of the filler, which not only take advantage of its inherent advantages, but also improve the interface area with the epoxy matrix. The composite materials with excellent properties are expected to provide theoretical guidance for the application of high thermal conductivity dielectric materials.     

Thermal properties of microcrystalline cellulose-filled PET–PTT blend polymer composites

Polymer composite materials were prepared from poly(ethylene terephthalate)–poly(trimethylene terephthalate) blends as the matrix and different microcrystalline cellulose (MCC) filler levels (0–40 wt%) using melt compounding followed by compression molding. The composites were analyzed using dynamic mechanical thermal analysis (DMTA), differential scanning calorimetry (DSC) and thermogravimetric analysis (TG). The DSC results indicated that there is no consistent or significant influence of the MCC addition on the glass transition (T _g), melting (T _m), and crystallization temperature of the composites. With increasing MCC content, dynamic mechanical properties improved because of the reinforcing effect of the MCC. The tan δ peak values from the DMTA were not significantly changed as the MCC content increased. TG indicated that the onset temperature of rapid thermal degradation decreased with increasing MCC content. It was also found that the thermal stability of the composites slightly decreased as the MCC content increased.     

Investigating the mechanical,thermal and melt flow index properties of HNTs – LLDPE nano composites for the applications of rotational moulding

Linear low density polyethylene (LLDPE) is the one of the most popular polymer used for rotational moulding applications such as storage tanks. But, its inferior mechanical properties and thermal stability restrict the longer service. Hence, this study experimentally demonstrates the effect of Halloysite Nanotube (HNTs) concentration on LLDPE composites for enhancing the mechanical and thermal stability. HNTs were uniformly dispersed with LLDPE matrix through ultra-sonication, followed by compression moulding used to prepare the nano composites plates. The prepared composites are shown 19.2% improved tensile strength for 2 wt% HNTs, whereas 28.9% hike in flexural strength observed for 4 wt% HNTs composite, compare to neat LLDPE. Which shows that higher concentrations of HNTs is favourable in improving the flexural strength rather than tensile properties. In addition to that, higher concentrations of HNTs are also helping in improving the storage modulus of the LLDPE composites. The increase in mechanical properties mainly attributed due to effective load carriers (HNTs) in the composite. Besides, HNTs were also contributing for improving the melting point and residual char of the composites, which is indeed for storage tanks durability. The prepared composite was thermally stable at higher temperature up to 230 °C, because of HNTs chemical structure, the inner layer of HNTs constitute with Al₂O₃ and outermost layer constitute with SiO_2, both are thermally stable. Stated enhancement proves the potential effect of HNTs reinforcement in the LLDPE composite for rotational moulding applications.     

Effect of electrostatic heterocoagulation of PVM/MA grafted carbon black and attapulgite nanorods on electrical and mechanical behaviors of waterborne polyurethane nanocomposites

In our previous report, poly(methyl vinyl ether-alt-maleic anhydride) grafted CB (GCB) with stable dispersion in water was successfully prepared. In the present study, waterborne polyurethane (WPU) nanocomposites including GCB and attapulgite (ATT) were prepared by liquid mixing method. Anionically charged GCB nanoparticles were heterocoagulated on the surface of cationically charged ATT nanorods at low pH value and improved the stabilization of ATT nanorods in water as a dispersing aid. The microstructure development in matrix that depended on various weight ratios of the nanoparticles ultimately influenced the electrical conductivity and mechanical properties of WPU nanocomposites. Composites containing equal concentrations of GCB and ATT showed reduced electrical conductivity, but significant increase in storage modulus. When the weight ratio of GCB to ATT was 5:1, both electrical conductivity and storage modulus of composite were improved simultaneously. The percolation threshold of composites containing a 5:1 (w/w) GCB/ATT ratio was lower than that of composites with GCB alone. The proposed mechanism for the effect of GCB and ATT on electrical or mechanical behaviors in composite was discussed in details. The clear evidence of microstructure development was also observed by transmission electron microscope.     

Preparation and characterization of glass fiber–reinforced polyethylene terephthalate/linear low density polyethylene (GF‐PET/LLDPE) composites

Polyethylene terephthalate (PET) was melt blended with linear low density polyethylene (LLDPE) and subsequently compounded with glass fibers (GF) as reinforcements at percentages ranging from 15 to 45 wt% of LLDPE and 5 to 30 wt% of GF. Thermal, morphological, and mechanical properties of the prepared composites were investigated. It was found that compounding PET/LLDPE blends with GF would be beneficial in producing composites that are thermally stable with good mechanical properties. For example, the impact strength of the composites containing 85/15 wt% (PET/LLDPE) at relatively high loading of GF, ie, from 15 to 30 wt%, was higher than that of the GF‐reinforced neat PET. When increasing the percentage of LLDPE in the composites, the impact strength increased with increasing GF content, and this was also better than that of GF‐reinforced PET whose impact strength drastically decreased upon increasing the GF%. The improvement in mechanical properties of the composite, we suggest, should be correlated with the morphologies of the composites where the visualized interface adhesion tended to be better at higher loadings of both LLDPE and GF.     

Electrospun Casein fibers obtained from revalued milk with mechanical and antibacterial properties

The present study describes the harnessing of revalued cow milk (denoted as waste milk) for fabricating casein fibers (CAS) with enhanced mechanical performance and antibacterial properties by the electrospinning method. For this purpose, polyethylene oxide (PEO) was employed (10 and 20 wt%) as a binder for the appropriate electrospun CAS fibers. Different amount of tannic acid (TA) was incorporated into casein/polyethylene oxide fibers (CAS/PEO) as a crosslinker agent, bringing filaments with a diameter of ca. 2 µm. The incorporation of 4 wt% of TA promotes the fibers' reticulation, forming a stable three-dimensional network. Also, the mechanical performance of CAS/PEO fibers was improved, where the tensile strength was increased from 0.91 MPa to 1.88 MPa with 4 % of TA, while the breaking elongation was increased from 93.74 % to 274.56 %. This behavior benefits the processing of fibers by electrospinning. Furthermore, the TA addition during the electrospun of CAS/PEO fibers enhances fibers' wettability properties and thermal stability induced by the crosslinker agent. Additionally, the antibacterial activity (AA) test demonstrates that CAS fibers can inhibit the growth of Gram-positive S. aureus and Gram-negative E. coli after 0.5 h, 1.5 h, 3 h, and 24 h of contact, which is generated by the TA addition. Our results suggest that the electrospun fabrication of CAS/PEO fibers with TA as a crosslinker agent represents an innovative harnessing of waste milk to produce functional textiles with potential biological application.     

Preparation of PLA-based nanocomposites modified by nano-attapulgite with good toughness-strength balance

Polylactic acid (PLA) was modified by poly (butylene adipate-co-terephthalate) (PBAT) and nano-attapulgite (AT) using the melt blending technique. Ethylene-butyl acrylate-glycidyl methacrylate (E-BA-GMA) was used as a compatibilizer which can bond the AT nanoparticles with PLA/PBAT matrix by interaction between the epoxy and hydroxyl groups. The effects of the AT content on the mechanical properties, thermal properties, crystallinity and morphology of PLA/PBAT/ATT nanocomposites were investigated. The results showed that the tensile strength, elongation at break and impact strength of PLA/PBAT could be simultaneously increased by incorporating AT nanoparticles. PLA/PBAT/AT nanocomposites possessed higher thermal stability than pure PLA/PBAT. In the ternary composite system of PLA/PBAT/AT, AT acted as a heterogeneous nucleating agent and was able to increase the crystallization temperature. When the AT content was low (≤2.5 wt%), AT nanoparticles could uniformly disperse in the PLA/PBAT matrix. In general, AT was an effective filler to reinforce and toughen PLA/PBAT blend simultaneously, and the PLA/PBAT/AT nanocomposite with 2.5 wt% AT exhibited a good combination of strength and toughness.     

Waterborne polyurethane/NiAl‐LDH/ZnO composites with high antibacterial activity

Novel waterborne polyurethane (WPU) composites based on NiAl‐LDH and ZnO were successfully synthesized by in‐situ polymerization. The nanostructured NiAl‐LDH/ZnO was first grafted by isophorone diisocyanate (IPDI), forming the NiAl‐LDH/ZnO‐NCO complex with ―NCO group on the surface, which promotes its homogeneous dispersion in WPU matrix. The microstructure and particle distribution of the composites were characterized. The mechanical properties and the water resistance of the composites were improved. Furthermore, the composites also exhibit significant antibacterial activity towards G(?) Escherichia coli and G(+) Staphylococcus aureus. Copyright © 2015 John Wiley & Sons, Ltd.     

Facile fabrication of organically modified boron nitride nanosheets and its effect on the thermal stability,flame retardant,and mechanical properties of thermoplastic polyurethane

Although hexagonal boron nitride (h‐BN) has presented a potential prospect in polymer composite fields, undesirable interfacial interaction with polymer matrix that generates serious aggregation of nanomaterials has suppressed its enhancement effect. Moreover, the chemically inert surface of h‐BN also makes the commonly used approach that improves the interfacial interaction between nanofillers and polymeric matrix invalid. Herein, the functionalized modification of chemically inert h‐BN was successfully fabricated by the adsorption of cetyl‐trimethylammonium bromide, with electrostatic interactions. The obtained h‐BN (cetyl‐trimethylammonium bromide‐BN) was well characterized by systematic tests and then added into thermoplastic polyurethane (TPU) matrix. The inclusion of functionalized h‐BN can dramatically improve thermal stability, flame retardant, and mechanical properties of TPU composites. With the incorporation of as low as 4.0 wt% nanofillers, maximal value of heat release rate and total heat release of TPU were reduced by 57.5% and 17.8%, compared with those of pure TPU, respectively. Moreover, tensile strength of TPU composite with a loading of 2.0 wt% was increased by 79.3% in comparison with that of neat TPU. The facile functionalized approach of chemically inert h‐BN paves the way for promising applications of h‐BN in the development of flame retardant polymer materials.     

Simultaneously improving the flame retardancy and mechanical properties for polyamide 6/aluminum diethylphosphinate composites by incorporating of 1,3,5‐triglycidyl isocyanurate

The effect of 1,3,5‐triglycidyl isocyanurate (TGIC) as a synergistic agent on the fire retardancy, thermal, and mechanical properties for polyamide 6/aluminium diethylphosphinate (PA6/AlPi) composites were investigated in detail by limiting oxygen index; vertical burning (UL‐94); cone calorimeter; thermal gravimetric analysis; rheological measurements; and the tests of tensile, flexural, and Izod impact strength. The morphologies and chemical compositions of the char residue were investigated by scanning electron microscopy, X‐ray photoelectron spectroscopy, and Fourier transform infrared spectra. The results demonstrated that AlPi and TGIC exerted an evident synergistic effect for flame retardant PA6 matrix, and the PA6/AlPi/TGIC composites with the thickness of 1.6 mm successfully passed UL‐94 V‐0 rating with the limiting oxygen index value of 30.8% when the total loading amount of AlPi/TGIC with the mass fraction of 97:3 was 11 wt%. However, the samples failed to pass the UL‐94 vertical burning tests when AlPi alone is used to flame retardant PA6 matrix with the same loading amount. The thermal gravimetric analysis data revealed that the introduction of TGIC promoted the char residue formation at high temperature. The rheological measurement demonstrated that the incorporation of TGIC improved the storage modulus, loss modulus, and complex viscosity of PA6/AlPi/TGIC composites comparing with that of neat PA6 and PA6/AlPi composites due to the coupling reaction between TGIC and the terminal groups of PA6 matrix. The morphological structures of char residues demonstrated that TGIC benefited to the formation of more homogenous and integrated char layer with no defects and holes on the surface comparing with that of PA6/AlPi composites during combustion. The higher melt viscosity of composites and the integrated and sealed char layer effectively inhibited the volatilization of flammable gas into the combustion zone and then led to the reduction of the heat release. The results of mechanical properties revealed that the incorporation of TGIC enhanced the mechanical properties for PA6/AlPi/TGIC composites comparing with that of PA6/AlPi composites with the same loading amount of flame retardant caused by the chain extension effect of TGIC. As a result, the flame retardancy and mechanical properties of PA6/AlPi composites simultaneously enhanced due to the introduction of TGIC.     

The effect of fiber content on the mechanical and thermal expansion properties of biocomposites based on microfibrillated cellulose

A new method to obtain composites of phenolic resin reinforced with microfibrillated cellulose with a wide fiber content was established and the mechanical properties were evaluated by tensile test. A linear increase in Young’s modulus was observed at fiber contents up to 40 wt%, with a stabilizing tendency for higher fiber percentages. These results were ratified by measurements of the coefficient of thermal expansion (CTE) relative to fiber content, which indicated a strong thermal expansion restriction rate below 60 wt% fiber content, indicating the effective reinforcement attained by the cellulose microfibrils. The low CTE achieved of 10 ppm/K is one of the important properties of cellulose composites.     

Waste marble dust-filled sustainable polymer composite selection using a multi-criteria decision-making technique

This research works with the optimal design of marble dust-filled polymer composites using a multi-criteria decision-making (MCDM) technique. Polylactic acid (PLA) and recycled polyethylene terephthalate (rPET)-based composites containing 0, 5, 10, and 20 wt% of marble dust were developed and evaluated for various physicomechanical and wear properties. The results showed that the incorporation of marble dust improved the modulus and hardness of both PLA and rPET. Moreover, a marginal improvement in flexural strength was noted while the tensile and impact strength of the matrices were deteriorating due to marble dust addition. The outcomes of wear analysis demonstrated an improvement in wear resistance up until 10 wt% filler reinforcement, after which the incidence of dust particles peeling off from the matrix was observed, thereby reducing its efficiency. The best tensile modulus of 3.23 GPa, flexural modulus of 4.39 GPa, and hardness of 83.95 Shore D were obtained for 20 wt% marble dust-filled PLA composites. The lowest density of 1.24 g/cc and the highest tensile strength of 57.94 MPa were recorded for neat PLA, while the highest impact strength of 30.94 kJ/m² was recorded for neat rPET. The lowest wear of 0.01 g was obtained for the rPET containing 5 wt% marble dust content. The experimental results revealed that for the examined criteria, the order of composite preference is not the same. Therefore, the optimal composite was identified by adopting a preference selection index-based MCDM technique. The findings demonstrated that the 10 wt% marble dust-filled PLA composite appears to be the best solution with favorable physical, mechanical, and wear properties.     

Anomalous reinforcing effects in cellulose gel-based polymeric nanocomposites

Cellulose-synthetic polymer nanocomposite films were prepared by immersion of cellulose gel in polymer solutions followed by dry casting. The cellulose hydrogel was prepared from aqueous alkali-urea solution. As the synthetic polymer, polystyrene (PS) and poly(methyl methacrylate) (PMMA) were used. The polymer content could be changed between 10 and 80% by changing polymer concentration of immersing solution. While the mechanical properties of the cellulose-PMMA composite films showed a nearly linear dependence on PMMA content, those of cellulose-PS composites showed an anomalous behavior; both tensile strength and Young’s modulus showed prominent maxima at 15–30 wt% PS contents. This anomaly may have resulted from the specific interaction between the aromatic ring of PS and the hydrophobic plane of the glucopyranoside. Both PMMA and PS composite films showed significant improvements in dimensional thermal stability; up to 25 wt% synthetic polymer content, the coefficient of thermal expansion (CTE) was as low as ca. 30 ppm/K, about 1/3 of the pure polymers. This indicates that the regenerated cellulose network is effective in suppressing thermal expansion of the synthetic polymers.     

The influence of matrix crystallinity,filler grain size and modification on properties of PLA/calcium carbonate composites

Thermal and mechanical properties of polylactide (PLA) composites with different grades of calcium carbonate, 40 nm and 90 nm nanoparticles, and also with submicron particles, unmodified and modified with calcium stearate or stearic acid, obtained by melt mixing, were compared. Films with amorphous and crystalline matrices were prepared and examined.T_g of PLA in the composites remained unaffected whereas its cold crystallization was enhanced by the fillers and predominantly depended on filler content. Filling decreased thermal stability of the materials but their 5% weight loss temperatures well exceeded 250 °C, evidencing stability in the temperature range of PLA processing. The amorphous nanocomposites with modified nanoparticles exhibited improved drawability and toughness without a significant decrease of tensile strength; nearly two-fold increase of the elongation at break and tensile toughness was achieved at 5 wt% content of the modified nanofiller. Lack of surface modification of the filler, larger grain size with an average of 0.9 μm, and matrix crystallinity had a detrimental effect on the drawability. However, the presence of nanofillers and crystallinity improved tensile modulus of the materials by up to 15% compared to neat amorphous PLA.     

New polymer electrolyte membrane for medium-temperature fuel cell applications based on cross-linked polyimide Matrimid and hydrophobic protic ionic liquid

New hydrophobic protic ionic liquid, 2-butylaminoimidazolinium bis(trifluoromethylsulfonyl)imide (BAIM-TFSI), has been synthesized. The ionic liquid showed good thermal stability to at least 350 °C. The conductivity of BAIM-TFSI determined by electrochemical impedance method was found to be 5.6 × 10^?2 S/cm at 140 °C. Homogeneous composite films based on commercial polyimide (PI) Matrimid and BAIM-TFSI containing 30–60 wt% of ionic liquid were prepared by casting from methylene chloride solutions. Thermogravimetric analysis data indicated an excellent thermal stability of PI/BAIM-TFSI composites and thermal degradation points in the temperature range 377 °C–397 °C. The addition of ionic liquid up to 50 wt% in PI films does not lead to any significant deterioration of the tensile strength of the polymer. The dynamic mechanical analysis results indicated both an increase of storage modulus E′ of PI/BAIM-TFSI composites at room temperature and a significant E′ decrease with temperature compared with the neat polymer. The cross-linking of the PI with polyetheramine Jeffamine D-400 allowed to prepare PI/Jeffamine/BAIM-TFSI (50%) membrane with E′ value of 300 MPa at 130 °C. The ionic conductivity of this cross-linked composite membrane reached the level of 10^?2 S/cm at 130 °C, suggesting, therefore, its potential use in medium-temperature fuel cells operating in water-free conditions.