New solid compounds of Tb(III), Ho(III), Er(III) and Yb(III) with chrysin

The time required for maximum hydration of MgO obtained from the calcination of magnesite was determined. The MgO samples were hydrated for different time intervals in both water and magnesium acetate. A thermogravimetric analysis (TG) method was used to determine the degree of hydration to Mg(OH)₂. Increasing the hydration time, the degree of hydration of MgO and surface area of the formed Mg(OH)₂ increased. A leveling effect was observed on the percentage Mg(OH)₂ obtained from hydration in magnesium acetate, and an optimum amount of 85% was obtained after 500 min. For the hydration in water, the leveling effect was only observed after 800 min giving a maximum of 65% Mg(OH)₂.     

Synthesis of High Dispersion and Uniform Nano-sized Flame Retardant-Used Hexagonal Mg(OH)<Subscript>2</Subscript>

Nanosized dispersive flake-like magnesium hydroxide (Mg(OH)₂) had been prepared by a hydrothermal method. In the process, when the surfactant polyvinyl pyrrolidone was added, high dispersion, small particle size and large specific surface area of hexagonal crystal magnesium hydroxide was obtained by ultrasonic dispersion and temperature program. The flame retardant of Mg(OH)₂ was systematically explored by scanning electron microscope (SEM), transmission electron microscopy, X-ray diffraction, BET analysis and thermo-gravimetric analysis tests. SEM showed the formation of uniform and small size magnesium hydroxide particle with hexagonal nanoscale. Under the optimized conditions, high nano-sized hexagonal Mg(OH)₂ was acquired with a mean particle size of 134 nm and a specific surface area of 26.66 m²/g. According to TGA results, the sample’s decomposition temperature was 626.9 K, which was consistent with the reported literature. It is vitally prospected that the prepared hexagonal Mg(OH)₂ is to be applied to the industry as a flame retardant.     

Effects of polystyrene-encapsulated magnesium hydroxide on rheological and flame-retarding properties of HIPS composites

In this study, polystyrene (PS)-encapsulated magnesium hydroxide (Mg(OH)₂) was successfully prepared by in situ polymerization of styrene on the surface of Mg(OH)₂ in a high-speed mixer. A large amount of PS chemically bonded on Mg(OH)₂ surface was confirmed by means of FT-IR, TGA and SEM. A series of composites of high impact polystyrene (HIPS) were prepared by melt blending in a co-rotating twin-screw extruder. The effects of PS-encapsulated filler on the properties of HIPS composites were studied by SEM, rheology and combustion tests (horizontal burning tests and cone calorimetry). The dispersion and adhesion patterns of PS-encapsulated Mg(OH)₂ in HIPS matrix were investigated through FT-IR and SEM. The experimental results demonstrated that comparing to the composites containing untreated filler, the rheological and flame retardant properties of those containing PS-encapsulated filler were found to be significantly improved. This improvement is mostly attributed to a better dispersion of the encapsulated filler and a strong adhesion between the filler and matrix.     

Effects of elastomer on morphology,flammability and rheological properties of HIPS/PS‐encapsulated Mg(OH)2 composites

The effects of elastomer type on morphology, flammability and rheological properties of high‐impact polystyrene/Mg(OH)₂ based on encapsulated by polystyrene have been investigated. The ternary composites characterized by cone calorimetry, horizontal burning rate, limiting oxygen index (LOI), rheology and SEM. Morphology was controlled using poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] triblock copolymer (SEBS) or the corresponding maleinated SEBS (SEBS‐g‐MA). As revealed by SEM observations, composites of HIPS/SEBS/Mg(OH)₂ exhibit separation of the filler and elastomer and good adhesion between SEBS and the filler, whereas composites of HIPS/SEBS‐g‐MA/Mg(OH)₂ exhibit encapsulation of the filler by SEBS‐g‐MA. The flame retardant and rheological properties of ternary composites were strongly dependent on microstructure. The rheological test showed that the composites with encapsulation structure exhibit a stronger solid‐like response at low frequency than those of the composites with separate dispersion structure. The combustion tests showed that the composites with encapsulation structure showed higher flame retardant properties than those of separate dispersion structure at optimum use level of SEBS‐g‐MA. However, with the increase of the content of SEBS‐g‐MA, the flame retardancy of the composite declined somewhat which can be explained that the SEBS‐g‐MA coating acts as a heat and mass transfer barrier due to the formation of encapsulation structure. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2023–2030, 2007     

Polypropylene filled with flame retardant fillers: mechanical and fracture properties

Two grades of isotactic polypropylene (homopolymer and block copolymer) were filled with magnesium and aluminium hydroxides, and studied focusing the mechanical and fracture characteristics of the composites. As expected, dispersion of such fillers in PP resulted in improved stiffness and reduced tensile yield strength. By one hand, the composites fracture resistance was characterised at low strain rate applying the J‐integral concept; the resistance to crack growth initiation (J_IC) was found decreasing as the Mg(OH)₂ concentration was raised in the copolymer PP matrix. By the other hand, the linear‐elastic fracture mechanics (LEFM) parameters were determined by means of instrumented impact tests at 1 m/s on the homopolymer PP filled with uncoated Al(OH)₃ particles. The higher the Al(OH)₃ mean particle size, the lower the composite fracture energy (G_IC). In the opposite, with commercial surface‐coated filler grades it was not possible to achieve LEFM conditions to characterise the fracture toughness of filled PP at 1 m/s, because the Mg(OH)₂ surface coating, which is applied in practice to improve the melt processing, acts increasing the composite plasticity and reducing the tensile yield strength.     

Controlled synthesis and enhanced bacteriostatic activity of Mg(OH)<Subscript>2</Subscript>/Ag nanocomposite

Silver nanoparticles have good sterilization performance due to their small size and large specific surface area, while the small size also brings about reunification and reduces the sterilization activity. To resolve the problem, magnesium hydroxide [Mg(OH)₂] microsphere was designed as a supported material to load silver particles on its surface. Mg(OH)₂ microspheres were successfully synthesized under the control of a biotemplate of eggshell membrane. X-ray diffraction, thermal gravimetric analysis/differential scanning calorimetry, and transmission electron microscopy were performed to characterize the Mg(OH)₂ microspheres. The results indicate that the Mg(OH)₂ microspheres of average size ~ 2 μm were formed from nanoflakes. The silver nanoparticles were loaded on the surface of Mg(OH)₂ microspheres to form Mg(OH)₂/Ag nanocomposite, which exhibited enhanced antibacterial effect compared to that of silver nanoparticles. The enhanced antibacterial mechanism was investigated in detail.     

Studies on melt flow properties during capillary extrusion of PP/Al(OH)3/Mg(OH)2 flame retardant composites

The apparent melt shear viscosity of polypropylene (PP) composites filled with aluminium hydroxide (Al(OH)₃) and magnesium hydroxide (Mg(OH)₂) was measured by means of a melt flow rate instrument under experimental conditions of temperature ranging from 170 to 195 °C and load varying from 2.16 to 12.5 kg, to identify the effects of particle size and content. The results showed that the melt shear flow of the composites obeyed the power law under the experimental conditions, the dependence of the melt apparent shear viscosity (η_a) on temperature was consistent with the Arrhenius equation, and the sensitivity of the η_a for the composite melts to temperature increased with addition of flame retardant. The η_a of the composites decreased with increasing apparent shear rate. The η_a increased with an increase of the content of flame retardant, but this rate of increase decreased with a rise of temperature or load. When the particle size of flame retardant was smaller than 5 μm, the η_a of the composites increased with increase of particle size of flame retardant, and then reduced with a further increase of particle size of flame retardant.     

Quantitative thermogravimetric analysis of binary mixtures

Thermogravimetric analysis is used to determine the amounts of Mg(OH)₂ and Mg(CH₃COO)₂in a mixture thereof. The application and suitability of different analysis methods are discussed. In the first method the mass losses in the temperature ranges as indicated by the decomposition of the pure compounds were used. Results obtained using these temperature ranges were unusable. The percentage mass losses due to the decomposition of Mg(OH)₂ and Mg(CH₃COO)₂ were then determined in a second method using the minimum in the derivative mass vs. temperature curves. The results obtained by this method compared well with the actual values for mixtures containing more than 15% magnesium acetate. The third method employed the total experimental mass loss of both decomposition reactions. The results obtained using this method compared well to the actual values, giving a R ² value of more than 0.99. This method of using the total mass losses can however only be used for binary mixtures that consist only of magnesium hydroxide and magnesium acetate. This revised version was published online in August 2006 with corrections to the Cover Date.     

矿化剂对水热法改性氢氧化镁晶体的影响

近几年来,氢氧化镁作为一种无机阻燃剂由于其具有制备条件相对温和,生产工艺简单且产品与自然环境友好等特点,在研究及生产活动方面备受关注且得到了长足的发展[1～4].目前采用氢氧化钠法进行反应一水热制备高分散阻燃级氢氧化镁的工艺路线已经比较成熟[5～8].然而,不利的是,氢氧化钠偏高的价格导致了产品的制造成本较高.而采用石灰法制备氢氧化镁阻燃剂具有价格低廉的特点,引起了人们的关注.     

Hydration of medium reactive industrial magnesium oxide with magnesium acetate

Medium reactive magnesium oxide reacts incompletely with available water to form magnesium hydroxide. To enhance the hydration of medium reactive magnesium oxide, the effect of magnesium acetate as hydrating agent was studied. The extent to which different parameters (concentration of magnesium acetate, solution temperature and solid to liquid ratio of MgO to magnesium acetate) influence the hydration rate of a medium reactive industrial sample of magnesium oxide were evaluated. The degree of rehydration measured as percentage Mg(OH)₂being formed, increases from approximately 56% using 0.5 M magnesium acetate solutions at 25°C to 64% at 50°C, to more than 70% at 70°C. The major part of rehydration of the medium reactive MgO sample occurs within the first few minutes of the reaction for all three temperatures studied. This revised version was published online in July 2006 with corrections to the Cover Date.     

13C, 25Mg and 11B solid-state NMR study of a fire retarded ethylene-vinyl acetate copolymer

Flame retardance of ethylene-vinyl acetate copolymer (EVA) can be achieved using magnesium hydroxide (Mg(OH)₂) incorporated in the polymeric matrix. The adduct of small amount of zinc borate as synergistic agent in the formulation increases the fire-proofing properties. Multinuclei solid-state NMR appears as a powerful means to characterise materials before and after combustion. We show that endothermic dehydration, water vapour evolved and formation of a glassy coating provide the flame retardancy of interest to the polymeric matrix.     

Formation and transformation of Mg(OH)2 in anodic coating using FTIR mapping

FTIR microscopic mapping was used to investigate the surface distribution of Mg(OH)₂ on anodic coatings. The results indicated Mg(OH)₂ was formed accompanying with micro-arc sparking and the amount of Mg(OH)₂ was related to the intensity of sparking, which depends on the applied voltage. The distribution and amount of Mg(OH)₂ varied with immersion time in 3.5 wt.% NaCl solution. The transformation process of anodic coatings was researched by FTIR microscopic mapping and smart map. The Cl^? could be absorbed on the surface of anodic coatings where Mg(OH)₂ is present and promote Mg(OH)₂ to transform into the soluble magnesium salt MgCl₂.     

Anwendung der fluoridspezifischen Elektrode bei der potentiometrischen Titration von Eisen(III) mit Athylendiamintetraacetat

The sample is dissolved at 185° C in conc. phosphoric acid and diluted to such an extent that the H₃PO₄ concentration is 0.2 M. In this solution Na and Mg are measured by AAS, using a propane-butane-N₂O flame. There are only slight chemical and physical interferences in this flame. The method is more rapid than other procedures for the determination of sodium (0.2–20%) and magnesium (0.1–20%) inβ-aluminate ceramics.     

Synthesis,characterization, and catalytic properties of the Li-doped ZnO

It has demonstrated that there are major advantages and synergistic effects on flame retardancy in using a combination of borates with magnesium hydroxide. In this paper, a novel 2MgO·B₂O₃·1.5H₂O–Mg(OH)₂ nanocomposite has been controllably prepared by in situ hydrothermal reaction, and the formation mechanism of the nanocomposite was proposed. As a comparison, 2MgO·B₂O₃·1.5H₂O nanobelt and Mg(OH)₂ nanosheet were also prepared. All samples were characterized by XRD, FT-IR, TG, SEM, TEM and HRTEM. Furthermore, their flame-retardant properties were investigated by thermal analysis method and oxygen index method, demonstrating that the flame retardancy of nanocomposite is significantly higher than that of single 2MgO·B₂O₃·1.5H₂O or Mg(OH)₂. The possible flame retarding mechanism has been proposed. It can be predicted that this nanocomposite could serve as a potential flame retardant.     

Effect of plasticizers (EC or PC) on the ionic conductivity and thermal properties of the (PEO)9LiTf: Al2O3 nanocomposite polymer electrolyte system

A new plasticized nanocomposite polymer electrolyte based on poly (ethylene oxide) (PEO)-LiTf dispersed with ceramic filler (Al₂O₃) and plasticized with propylene carbonate (PC), ethylene carbonate (EC), and a mixture of EC and PC (EC+PC) have been studied for their ionic conductivity and thermal properties. The incorporation of plasticizers alone will yield polymer electrolytes with enhanced conductivity but with poor mechanical properties. However, mechanical properties can be improved by incorporating ceramic fillers to the plasticized system. Nanocomposite solid polymer electrolyte films (200–600 μm) were prepared by common solvent-casting method. In present work, we have shown the ionic conductivity can be substantially enhanced by using the combined effect of the plasticizers as well as the inert filler. It was revealed that the incorporating 15 wt.% Al₂O₃ filler in to PEO: LiTf polymer electrolyte significantly enhanced the ionic conductivity [σ _RT (max)?=?7.8?×?10^?6 S cm^?1]. It was interesting to observe that the addition of PC, EC, and mixture of EC and PC to the PEO: LiTf: 15 wt.% Al₂O₃ CPE showed further conductivity enhancement. The conductivity enhancement with EC is higher than PC. However, mixture of plasticizer (EC+PC) showed maximum conductivity enhancement in the temperature range interest, giving the value [σ _RT (max)?=?1.2?×?10^?4 S cm^?1]. It is suggested that the addition of PC, EC, or a mixture of EC and PC leads to a lowering of glass transition temperature and increasing the amorphous phase of PEO and the fraction of PEO-Li⁺ complex, corresponding to conductivity enhancement. Al₂O₃ filler would contribute to conductivity enhancement by transient hydrogen bonding of migrating ionic species with O–OH groups at the filler grain surface. The differential scanning calorimetry thermograms points towards the decrease of T _g , crystallite melting temperature, and melting enthalpy of PEO: LiTf: Al₂O₃ CPE after introducing plasticizers. The reduction of crystallinity and the increase in the amorphous phase content of the electrolyte, caused by the filler, also contributes to the observed conductivity enhancement.     

Hydration of medium reactive magnesium oxide using hydration agents

Water, magnesium acetate, magnesium chloride, acetic acid and hydrochloric acid were used as hydrating agents for an industrially obtained MgO sample. The influence of these different hydrating agents on the pH of the hydrating solution, degree of hydration to Mg(OH)₂, and product surface area was studied as a function of the temperature of hydration. When compared to the hydration in water, all hydrating agents improved the degree of hydration between 5 and 50% at all temperatures. MgCl₂ and a mixture of HCl and Mg(CH₃COO)₂ seemed to be the most effective hydrating agents below 60°C, while at temperatures above 60°C Mg(CH₃COO)₂ formed the largest percentage Mg(OH)₂. Mg(CH₃COO)₂ was the hydrating agent that showed the strongest temperature dependence. The mechanism of the hydration reaction seems to be dependent of the availability of Mg²⁺ ions and the increased formation of Mg(OH)₂ as temperature increases.     

The effect of calcining conditions on the rehydration of dead burnt magnesium oxide using magnesium acetate as a hydrating agent

Summary Magnesium oxide was produced through calcination of magnesite ore. A rehydration percentage of MgO to Mg(OH)₂ of higher than 60% is obtained using calcination temperatures of 1000°C and below. At these temperatures medium reactive MgO was formed. The extend to which dead burnt MgO (obtained after calcination at 1200°C and higher) may be rehydrated is dependent on the calcination time, but even after 1 h and using magnesium acetate as a hydrating agent only 40% of the initial product has rehydrated to Mg(OH)₂. After 4 and more hours of calcinations at 1200°C, a maximum of approximately 14% of the initial MgO is rehydrated back to Mg(OH)₂. Thermogravimetric analysis was performed on the various compounds to determine the amounts of Mg(OH)₂ that formed.     

Interphase structure development in impact modified PP/Mg(OH)2 composites reactively processed with 1,3‐phenylene dimaleimide

Interphase modification of impact modified isotactic poly(propene) (IMPP)/magnesium hydroxide (Mg(OH)₂) composites, via use of the reactive modifier 1,3 phenylene dimaleimide (BMI) has led to the formation of composites that have strength and toughness more than twice that of the unmodified composite. These significant improvements in properties were found (via response surface analysis, DSC and matrix extraction‐DRIFTS studies) to be due to encapsulation of the filler particles with the elastomeric poly(ethene‐co‐propene) impact modifier phase of the IMPP. Acceptable processing characteristics can be realised together with excellent mechanical properties, via judicious addition of a lubricant (a fatty acid amide/ester blend) to the formulation.     

The Effect of Flower-Like Magnesium Hydroxide Nanostructure on the Thermal Stability of Cellulose Acetate and Acrylonitrile–Butadiene–Styrene

Flower-like magnesium hydroxide (Mg(OH)₂) nanostructures were synthesized via a simple hydrothermal reaction at relatively low temperature. The Mg(OH)₂ nanostructures were then added to acrylonitrile–butadiene–styrene (ABS) and cellulose acetate (CA) polymers. The effect of Mg(OH)₂ nanostructures on the thermal stability of the polymeric matrixes has been investigated. The thermal decomposition of the nanocomposites shifts towards higher temperature in the presence of the Mg(OH)₂. The enhancement of thermal stability of nanocomposites is due to endothermically decomposition of magnesium hydroxide that releases of water and dilutes combustible gases. Nanostructures and nanocomposites were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), Fourier transform infrared (FT-IR) spectroscopy, thermogravimetric analysis (TGA), differential thermal analysis (DTA), UL-94 test and limiting oxygen index (LOI) analysis.     

Synthesis,spectral characterization,and luminescence properties of a cup-like ligand and its magnesium(II) complex

A new tripodal ligand, N,N′,N″-tri(salicylaldehyde)triaminotriethylamine (1) has been synthesized and characterized by elemental analysis, IR and UV spectroscopy, MS, and X-ray crystallography. X-ray diffraction analysis reveals that the three chains of the ligand form a cup-like structure. The ligand’s magnesium(II) complex has been synthesized and characterized by elemental analysis, conductivity, and IR and UV spectroscopy. The luminescence properties of the ligand and its magnesium(II) complex were investigated in DMF, CH₃OH, and CH₃CH₂OH solution and in the solid state at room temperature.