反胶束法制备SiO2包裹的ZnS:Mn/ZnS量子点

采用反胶束法制备了SiO2包裹的ZnS∶Mn/ZnS量子点(1)。1的UV吸收峰在295 nm附近,低于体相ZnS(约340 nm);1中Mn2+含量升高,ZnS基质的缺陷荧光发射峰减弱,595 nm处的Mn2+特征荧光发射峰增强;但Mn2+含量过高时产生荧光淬灭。光学显微镜和透射电镜分析表明,1分散性较好,内核呈结晶态;Mn2+含量为2.2%时,1的内核直径和SiO2壳层厚度分别为6 nm和5 nm左右。     

甲基三乙氧基硅烷修饰的Ti3+/SiO2复合薄膜的发光性能

采用溶胶-凝胶(Sol-Gel)法, 以正硅酸乙酯(TEOS)和甲基三乙氧基硅烷(MTES)为先驱物, 盐酸为催化剂, 用二步水解法制备了Ti3+/SiO2薄膜和甲基三乙氧基硅烷修饰的Ti3+/SiO2复合薄膜. 采用红外光谱仪、X射线衍射仪、椭偏仪、荧光光谱仪等对膜层性质进行了分析. 结果表明, 掺杂Ti3+的SiO2薄膜分别在250 nm附近有一弱的激发峰, 294 nm附近有一强的激发峰, 在393 nm附近出现一强的发射峰. IR光谱发现, MTES修饰的Ti3+/SiO2复合薄膜的Si—OH的吸收峰强度比Ti3+/SiO2薄膜的略减小, Si—O—Si的吸收峰明显增强, 表明复合薄膜硅氧网络结构更规则, 有利于Ti3+的均匀分散. Ti3+/SiO2薄膜与复合薄膜的孔隙率分别为13.64%和6.66%, 表明MTES的加入使薄膜更致密. 在空气中陈放30 d后, Ti3+/SiO2薄膜已经检测不到荧光发射峰, 而MTES修饰的Ti3+/SiO2复合薄膜荧光强度只下降了18%. 在氮气中陈放30 d后, 普通薄膜与复合薄膜的荧光强度均仅下降了10%. 表明Ti3+的荧光猝灭的主要原因是由于Ti3+被氧化造成的. 溶胶中加入MTES后, 薄膜表面结构得到改善, 有效地防止了Ti3+的氧化, 荧光强度更稳定.     

表面活性剂增溶比率荧光Zn2+检测方法研究

合成了一种新的Zn2+荧光检测试剂8-(2-(十八氨基)乙酰氨基)喹啉(AQZ-18)。通过自发荧光的非离子表面活性剂OP-10增溶AQZ-18,获得了一个与Zn2+结合后在320 nm和505 nm分别有两个荧光发射峰的溶液体系。短波长荧光峰来自OP-10,荧光峰强度不随Zn2+浓度变化;长波长荧光峰来自AQZ-18,荧光峰强度随Zn2+浓度增加而增强。利用上述两个荧光峰强度随Zn2+浓度变化时的比值变化建立了一种新的比率荧光Zn2+检测方法。研究表明,Zn2+与AQZ-18形成1∶1型基态配合物,其表观结合常数为1.1×106L/mol。常见金属离子对Zn2+荧光检测无干扰,Zn2+浓度在0～1.1×10-5mol/L范围内与荧光强度变化的比值呈良好的线性关系,相关系数(r2)为0.996 2,检出限为55 nmol/L。该方法可用于水样中Zn2+的检测。     

基于羟苯基苯并咪唑的Zn2+比率荧光探针

通过羰基将两分子2-(4-氨基-2-羟苯基)苯并咪唑(4-AHBI)连接,合成了结构高度对称的新化合物N,N′-二-[3-羟基-4-(2-苯并咪唑)苯基]脲(C27H20N6O3,1),测试了不同溶剂条件下1的紫外吸收和荧光发射光谱,研究了1对Zn2+的选择性识别作用。结果表明,随着溶剂极性的增大,1的紫外吸收峰发生蓝移,激发态分子内质子转移(ESIPT)荧光发射峰明显增强。与4-AHBI相比,1在乙腈溶液中的紫外吸收强度增强约3.5倍,最大吸收峰红移8 nm,荧光发射增强8倍多。1在乙腈溶液中的Zn2+荧光响应行为表明1与Zn2+的结合将导致1在445 nm处的荧光强度不断降低,而在395 nm处出现的新峰的荧光强度不断增强,具有比率荧光探针的特点,而且检测范围较宽,可达1×10-6-1×10-2 mol.L-1。     

金核壳纳米粒子的控制合成及其生物复合(英文)

合成了一系列Au/SiO2核壳纳米粒子,并详细研究了Au纳米壳层的生长过程。发现在金纳米壳层形成的过程中存在着2个竞争反应。利用这一发现,可将金纳米壳层的吸收峰从524nm连续调谐至980nm处。恩度是一种临床抗癌药物,我们首次将其生物复合于吸收峰位于808nm的Au/SiO2壳层表面,得到Au/SiO2-Endo,通过FTIR测试证明该生物复合成功。将恩度特殊的饿杀肿瘤特性以及对肿瘤具有特异识别能力,与Au/SiO2纳米壳层结构的光学可调谐特性以及良好的光热转换能力复合于一体,我们期望得到一种治疗肿瘤效果更强的新型药物。     

SiO2/LaF3:Eu3＋核壳结构发光粒子的制备与表征

采用简单的液相法合成了SiO2/LaF3:Eu3＋核壳结构发光粒子, 并对其结构及发光性能进行了表征. XRD分析表明包覆层LaF3:Eu3＋为立方晶相结构, 红外光谱表明SiO2颗粒表面有柠檬酸的修饰, 电镜照片表明合成了球形的核-壳结构的复合粒子, 包覆层厚度为10～20 nm, 光谱测试表明核-壳复合粒子与纯的LaF3:Eu3＋具有相同的发光性能, 均以589 nm附近的5D0—7F1磁偶极跃迁为最强发射峰, 说明Eu3＋在LaF3基质中占据的格位相同.     

对称性降低的SiO2/Ag核壳结构纳米粒子的制备及表面增强拉曼活性研究

采用湿化学还原法在自组装的单层阵列二氧化硅纳米粒子表面沉积银膜制备了SiO2核/Ag帽复合纳米结构。通过透射电镜(TEM)、扫描电镜(SEM)、X射线衍射(XRD)和紫外-可见分光光度计(UV/Vis)研究和表征了该复合纳米结构的表面形貌、结构及光学性质。所制备的复合纳米粒子表面粗糙,其表面呈现无数纳米级谷粒状结构,SiO2内核粒径为350nm的银纳米帽的表面等离子共振吸收的2个共振峰分别位于382和689nm处。以亚甲基蓝作为探测分子研究了SiO2粒径为350和450nm的SiO2/Ag帽状复合纳米粒子的表面增强拉曼散射(SERS)活性,增强因子分别为3.6×109和3.9×109。结果表明,湿化学还原法制备的SiO2核/Ag帽复合纳米结构是很好的拉曼活性基底。     

取向Zn1-xMgxO纳米线阵列的制备及光学特性

采用化学气相沉积(CVD)法, 以高纯ZnO、Mg和活性C混合粉末为原料, 在Si(111)衬底上制备了不同配比的取向Zn1-xMgxO纳米线阵列. 用X射线衍射仪(XRD), 扫描电镜(SEM), 能量色散X射线分析(EDAX)及光致发光(PL)光谱分析仪对样品的晶体结构、形貌、成分组成和光致发光特性进行了分析. 用霍尔效应测量系统测试了不同配比样品的载流子浓度. 实验发现, 当Zn1-xMgxO纳米线阵列中Mg原子相对Zn原子摩尔比x值较小时(x<0.29), XRD衍射谱中只有ZnO晶体标准衍射峰, 没有MgO晶体衍射峰, 说明此时制备的Zn1-xMgxO纳米线样品晶格结构以ZnO纤锌矿结构为主, Mg原子只是作为替位或填隙原子分布在ZnO晶体中. 但当样品中x>0.53时, ZnO与MgO的特征衍射峰同时出现在样品的衍射谱图中, 说明随原料中Mg原子摩尔比的增加, 制备的Zn1-xMgxO纳米阵列样品中ZnO纤锌矿结构与MgO岩盐结构同时存在, 样品呈现多晶体结构形式. 实验还对比了制备的纯ZnO与不同配比的Zn1-xMgxO纳米线阵列的光致发光光谱和载流子浓度, 发现随Mg含量的增加, Zn1-xMgxO阵列紫光发光峰出现了较明显的蓝移现象, 同时, 测试结果也表明, 随Mg含量的增加, Zn1-xMgxO阵列的紫光和绿光峰发光强度都有所减弱, 样品的载流子浓度也随之下降. 文章对实验结果进行了分析和探讨.     

银/二氧化硅核壳纳米颗粒的制备及其壳层厚度对其光学性质的影响

通过溶胶-凝胶法,制备了银/二氧化硅核壳材料(Ag@SiO2),对SiO2壳层厚度进行了有效调控,并系统研究了壳层厚度对银的等离子体共振峰(LSPR)以及对折射率灵敏度(RIS)的影响。研究结果表明,随SiO2壳层包覆厚度的增加,银纳米颗粒的LSPR吸收峰呈现先红移后蓝移的规律。对于粒径为50 nm的银纳米颗粒,当SiO2壳层达到65 nm时,LSPR最大吸收波长为465 nm。进一步增加SiO2壳层厚度,LSPR发生蓝移并且强度变弱,当SiO2壳层达到120 nm时,LSPR吸收峰已无法清晰辨认。研究了Ag@SiO2材料的RIS效应,发现随着SiO2厚度的增大RIS效应逐渐变小。     

SiO_2/PE/Bi_2S_3核壳结构纳米颗粒的合成与性能(英文)

以多层电解质作为微型反应器,制备了SiO2/Polyelectrolyte(PE)/Bi2S3核壳纳米粒子。XRD结果表明Bi2S3颗粒属于正交晶系。由透射电镜和场发射扫描电镜照片可知,在直径为640nm左右的SiO2表面覆盖了厚度35nm的Bi2S3壳层。红外光谱分析结果表明硅烷网络在结构上发生了变化(SiO2表面的硅烷醇键沉积在Bi2S3的表面)。SiO2核和SiO2/PE/Bi2S3的紫外-可见吸收光谱显示在900nm存在典型吸收边。     

Solvent extraction separation of In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/ with sulphoxides

Solvent extraction studies have been made on some metals: In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/, from ammonium thiocyanate solutions by dialkyl sulphoxides. Separation of these metals from one another can be achieved by suitable choice of the extracted conditions. The nature of the extractable metal species has been elucidated.     

Simultaneous propane dehydrogenation andco2hydrogenation overCrOx/SiO2catalyst

Summary Single reverse water-gas shift (RWGS) and dehydrogenation of propane with CO₂(DH-CO₂) reactions in the presence and absence of the CrO_x/SiO₂ catalyst have been studied between 673 and 873 K. It was found that the CrO_x/SiO₂ catalyst is active both in the dehydrogenation of propane and in the RWGS reactions. The obtained results suggest that the dehydrogenation of propane to propene in the presence of CO₂on CrO_x/SiO₂can be facilitated by the RWGS reaction.</o:p>     

Synthesis of chlorobis/β-diketonato/oxotechnetium/V/ and tris/β-diketonato/technetium/III/ complexes

Chlorobis/-diketonato/ oxotechnetium/V/ complexes [TcOCl/-dik/₂, -diketone=acetylacetone, benzoylacetone and dibenzoylmethane] were newly synthesized using macroamount of⁹⁹Tc. These complexes were further separated into geometrical isomers. Furthermore, an improvement of the yields for the syntheses of tris/-dike-tonato/technetium/III/ complexes [Tc/-dik/₃, -diketone=acetylacetone, benzoylacetone and 2-thenoyltrifluoroacetone] was examined using Tc/III/-thiourea complexes as a starting material.     

Direct synthesis of dimethyl carbonate ?from CH3OH AND CO2 by H3PW12O40/CexTi1-xO2 catalyst

Summary Ce_xTi_1-xO₂ and H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts were prepared using a sol-gel method, and applied to the direct synthesis of dimethyl carbonate from methanol and carbon dioxide. H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ showed a better catalytic performance than the corresponding Ce_xTi_1-xO₂, due to the bifunctional catalysis of Br?nsted acid sites (provided by H₃PW₁₂O₄₀) and base sites (provided by Ce_xTi_1-xO₂). H₃PW₁₂O₄₀/Ce_0.1Ti_0.9O₂ showed the highest catalytic performance among the H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts.     

Crystal structure of Na3PO4 · 12H2O

The crystal structure of trisodium monophosphate hemihydrate was determined. The space group is $\text{C2}\text{c}$ and a unit cell contains eight formula units. The unit cell dimensions of $\text{Na}{}_3\text{PO}{}_4\text{·}\text{1}\text{2}\text{H}{}_2\text{O}$ are a = 9.631(3), b = 5.416(2), c = 16.938(8) Å, β = 102.60(5)°. The final R value is 0.027 for a set of 1430 independent reflections. This atomic arrangement is mainly a three-dimensional network of distorted NaO₆ octahedra. The hydrogen bonding scheme is given.     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

Synthesis and characterization of Ti1−2xNbxNixO2−x/2 solid solutions

Doped-rutile has been traditionally used in ceramic pigments for its intense optical properties. In this paper, we compare the classical ceramic synthesis of Ti_1−2xNb_xNi_xO_2−x/2 system with the sol-gel methodology, which allows a reduction of the anatase-rutile transformation temperature. The composition was optimised in order to obtain a unique rutile phase with the minimum amount of pollutant Ni(II) and enhanced chromatic coordinates. Incorporation of the doping ions in the rutile structure was corroborated by XRD and Rietveld refinements. The species responsible for the colour mechanism were studied by different techniques. UV-VIS spectroscopy showed the characteristic features of Ni²⁺ ions, whose existence was corroborated by EPR and magnetic measurements. From these results, (Ni,Nb)doped-TiO₂ powder samples can be now shaped as thin films, monoliths, etc. by using sol-gel methodology without modifying their properties. This study introduces new possibilities of coloured TiO₂-based solid solutions in new combined advanced applications (colouring agent and photocatalyst, etc.).     

An investigation of the promotional effect of propylene or propane traces on the activity of sulfatedPt/g-Al2O3andPt-Sn/g-Al2O3inCH4combustion

Summary A strong promoting effect of the presence of C₃H₈or C₃H₆was determined for the combustion of CH₄in excess oxygen, over pre-sulfated 1%Pt/g-Al₂O₃and pre-sulfated 1%Pt-2%Sn/g-Al₂O₃catalysts.</o:p>     

LixZryOz三元化合物的制备及表征

采用高温固相法制备了4种高纯度晶相组成的LixZryOz三元化合物,研究了焙烧温度、时间、反应物的种类和初始反应物物质的量比对产物组成的影响,进一步用XRD、SEM及BET分析方法对产物的晶相结构、表面形貌及比表面积进行了表征.实验结果表明,Li2CO3与ZrO2在适当条件下可以合成得到单斜相Li3ZrO3;以LiOH替代Li2CO3,在适当条件下可以分别合成得到四方相Li2ZrO3和三斜/单斜相Li6Zr2O7;进一步以Zr(NO3)4·5H2O代替Zr02,可将单斜相Li6Zr2O7的制备时间由96 h缩短至24 h.SEM照片显示产物硬团聚明显,粒径分布在1～10μm间,BET分析表明样品比表面积处于1.0～9.0 m2·g-1间分布,反应过程中锂的过量以及长时间高温焙烧是引起产物粒径长大和产生硬团聚的主要原因.     

Visible light-sensitive yellow TiO2−xNx and Fe-N co-doped Ti1−yFeyO2−xNx anatase photocatalysts

Nitrogen substituted yellow colored anatase TiO_2−xN_x and Fe-N co-doped Ti_1−yFe_yO_2−xN_x have been easily synthesized by novel hydrazine method. White anatase TiO_2−δ and N/Fe-N-doped samples are semiconducting and the presence of ESR signals at g ∼1.994-2.0025 supports the oxygen vacancy and g∼4.3 indicates Fe³⁺ in the lattice. TiO_2−xN_x has higher conductivity than TiO_2−x and Fe/Fe-N-doped anatase and the UV absorption edge of white TiO_2−x extends in the visible region in N, Fe and Fe-N co-doped TiO₂, which show, respectively, two band gaps at ∼3.25/2.63, ∼3.31/2.44 and 2.8/2.44 eV. An activation energy of ∼1.8 eV is observed in Arrhenius log resistivity vs. 1/T plots for all samples. All TiO₂ and Fe-doped TiO₂ show low 2-propanol photodegradation activity but have significant NO photodestruction capability, both in UV and visible regions, while standard Degussa P-25 is incapable in destroying NO in the visible region The mid-gap levels that these N and Fe-N-doped TiO₂ consist may cause this discrepancy in their photocatalytic activities.