Structure and redox properties of CexPr1−xO2−δ mixed oxides and their catalytic activities for CO, CH3OH and CH4 combustion

A series of Ce_xPr_1−xO_2−δ mixed oxides were synthesized by a sol–gel method and characterized by Raman, XRD and TPR techniques. The oxidation activity for CO, CH₃OH and CH₄ on these mixed oxides was investigated. When the value x was changed from 1.0 to 0.8, only a cubic phase CeO₂ was observed. The samples were greatly crystallized in the range of the value x from 0.99 to 0.80, which is due to the formation of solid solutions caused by the complete insertion of Pr into the CeO₂ crystal lattices. Raman bands at 465 and 1150 cm⁻¹ in Ce_xPr_1−xO_2−δ samples are attributed to the Raman active F_2g mode of CeO₂. The broad band at around 570 cm⁻¹ in the region of 0.3 ≤ x ≤ 0.99 can be linked to oxygen vacancies. The new band at 195 cm⁻¹ may be ascribed to the asymmetric vibration caused by the formation of oxygen vacancies. The TPR profile of Pr₆O₁₁ shows two reduction peaks and the reduction process is followed: . The reduction temperature of Ce_xPr_1−xO_2−δ mixed oxides is lower than those of Pr₆O₁₁ or CeO₂. TPR results indicate that Ce_xPr_1−xO_2−δ mixed oxides have higher redox properties because of the formation of Ce_xPr_1−xO_2−δ solid solutions. The presence of the oxygen vacancies favors CO and CH₃OH oxidation, while the activity of CH₄ oxidation is mostly related to reduction temperatures and redox properties.     

Synthesis, structure and oxygen nonstoichiometry of La0.4Sr0.6Co1−yFeyO3−δ

The samples of La_0.4Sr_0.6Co_1−yFe_yO_3−δ (y = 0.2 and 0.4) were prepared using both conventional ceramic technique and nitrate–citrate precursors technique. The phase identification was made by X-ray diffraction method. The refinement of structural parameters from the XRD and neutron diffraction measurements was performed by full profile Rietveld analysis. Neutron diffraction showed that both samples possess distorted perovskite-type structure. Oxygen nonstoichiometry was measured by chemical analysis and thermogravimetry (TG) analysis in the range 20 ≤ T/°C ≤ 900 and 2E-5 ≤ pO₂/atm ≤ 4E-1. TG-experiments indicate a relatively fast and reversible oxygen exchange at pO₂ > 1E-2 atm. Mass saturation occurs at T < 300 °C upon cooling. The absolute value of oxygen nonstoichiometry was determined by iodometric titration measurements. It was found that both samples have practically stoichiometric composition at 300 °C in air and δ increases with increasing temperature and decreasing oxygen partial pressure.     

Synthesis and low temperature fluorination of the alkaline-earth palladates Ba2−xSrxPdO3 (x = 0–2)

Since the discovery of superconductivity in Sr₂CuO₂F_2+δ there has been an increased interest in ternary oxide-fluorides. Sr₂CuO₂F_2+δ is prepared via low temperature (T = 220 °C) reaction routes. Low temperature fluorination induces an interesting structural rearrangement in the parent compound Sr₂CuO₃, which is a one-dimensional material containing linear chains of vertex sharing CuO₄ squares along the crystallographic b axis. Upon fluorination, one oxide is substituted by two fluorides and Cu²⁺ becomes octahedrally coordinated by four oxides and two fluorides. The fluorinated compound Sr₂CuO₂F_2+δ displays the T-type structure (La₂CuO₄). Insertion of excess fluorine, δ, also takes place and this fluorine occupies interstitial sites in the T structure. Although the starting material Ca₂CuO₃ is isostructural to Sr₂CuO₃, Ca₂CuO₂F_2+δ displays the T′ (Nd₂CuO₄) structure due to the smaller radius of Ca²⁺ compared to that of Sr²⁺.

The alkaline-earth palladates with the general formula A₂PdO₃ (A = Ba, Sr) are isostructural with the A₂CuO₃(A = Ca, Sr) materials. We prepared the Ba_2−xSr_xPdO₃ (x = 0–2) series and performed low temperature fluorination, which led to the synthesis of the series Ba_2−xSr_xPdO₂F_2+δ (0 ≤ x ≤ 1.5). All the compounds in the Ba_2−xSr_xPdO₂F_2+δ series show T′ structure (Ca₂CuO₂F_2+δ). Similarities and differences with Sr₂CuO₂F_2+δ and Ca₂CuO₂F_2+δ will be discussed.     

Phase equilibria and crystal structure of the solid solution LaFe1−xNixO3−δ (0 ≤ x ≤ 1)

Phase equilibria in the LaFeO₃–“LaNiO₃” were studied at 1100 °C in air. The samples were synthesized by standard ceramic and/or solution route via nitrate or citrate precursors. According to the results of XRD it was found that the homogeneity ranges of LaFe_1−xNi_xO_3−δ solid solution lay within 0.0 ≤ x ≤ 0.4 (sp.gr. Pbnm) and 0.6 ≤ x ≤ 0.8 (sp.gr. ). The structural parameters (bond lengths, atom coordinates) for the single-phase samples were refined using Rietveld analysis. The unit cell parameters versus LaFe_1−xNi_xO_3−δ composition are presented.     

Thermogravimetric study on perovskite-like oxygen permeation ceramic membranes

The oxygen permeation properties of mixed-conducting ceramics SrFeCo_0.5O_3−δ (SFCO), Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ (BSCFO), La_0.2Sr_0.8Co_0.8Fe_0.2O_3−δ (LSCFO) and Ba_0.95Ca_0.05Co_0.8Fe_0.2O_3−δ (BCCFO) were studied by thermogravimetric method in the temperature range 600–900 °C. The results show that the oxygen adsorption rate constants k_a of all material are larger than oxygen desorption rate constants k_d and both k_a and k_d are not strongly dependent on temperature in the studied temperature range. The oxygen vacancy contents δ(N₂) and δ(O₂) in nitrogen and oxygen and their difference Δδ = δ(N₂) − δ(O₂) play an important role in determining the temperature behavior of oxygen permeation flux J_O2.     

Structure analysis and the standard molar enthalpy of formation of a coordination polymer [Co(TO)2Cl2]n (TO = 1,2,4-triazole-5-one)

A coordination polymer was synthesized by the reaction of CoCl₂ with 1,2,4-triazole-5-one (TO) and charaterized by means of IR and TG–DTG. Single-crystal structure analysis showed that the complex crystallized in the monoclinic space group C2/c: a = 23.105(9) Å, b = 3.5683(2) Å, c = 13.589(6) Å,  = 90°, β = 124.038(4)°, γ = 90°, V = 928.4(7) Å³, Z = 4. The standard molar enthalpy of formation of the complex was determined to be (−1034.28 ± 0.95) kJ mol⁻¹.     

Oxygen permeation through a Ce0.8Sm0.2O2−δ–La0.8Sr0.2CrO3−δ dual-phase composite membrane

A composite of oxygen ion conducting oxide Ce_0.8Sm_0.2O_2−δ (60 vol.%) and electron conducting oxide La_0.8Sr_0.2CrO_3−δ was prepared by sintering a powder compact at a temperature of 1550 °C. No significant reaction between the two constituent oxides was observed under preparation and oxygen permeation conditions. Appreciable oxygen permeation fluxes through the composite membrane were measured at elevated temperatures with one side of it exposed to the ambient air and the other side to a flowing helium gas stream. The oxygen flux initially increased with time, and took a long time to reach a steady value. A steady oxygen permeation flux as high as 1.4 × 10⁻⁷ mol cm⁻² s⁻¹ was obtained with a 0.3 mm thick membrane at 950 °C under a relatively small oxygen partial pressure difference of 0.21 bar/0.0092 bar. It was revealed that the overall oxygen permeation process was mainly limited by the transport in the bulk of the membrane in the range of the membrane thickness greater than 1.0 mm, and the limitation by the surface oxygen exchange came into play at reduced thickness of 0.6 mm.     

Survey of the quasi-ternary system La0.8Sr0.2MnO3–La0.8Sr0.2CoO3–La0.8Sr0.2FeO3

An overview on the variation of the thermal expansion, the electrical conductivity as well as non-stoichiometry of the oxide content as a function of composition within the quasi-ternary system La_0.8Sr_0.2MnO_3−δ–La_0.8Sr_0.2CoO_3−δ–La_0.8Sr_0.2FeO_3−δ in air is presented. The various powders were synthesized under identical conditions. The DC electrical conductivity values of the compositions at 800 °C in air vary in a wide range from 15 to 1338 S cm⁻¹. The magnitude of electrical conductivity of the perovskites is mainly determined by the percentage of cobalt in the compositions. A similar behaviour was observed for the measured thermal expansion coefficients between room temperature and 1000 °C in air, increasing from 10.9 to 19.4 × 10⁻⁶ K⁻¹ as a function of cobalt content. Changes in the oxygen stoichiometry of the materials were characterized by temperature-programmed oxidation measurements.     

Single crystal growth of Bi1−xSrxMnO3—Thermodynamics and experiment

The primary crystallization field of a perovskite solid solution Bi_1−xSr_xMnO_3−δ was delimited by calculating the respective phase equilibria in the quaternary Bi–Sr–Mn–O system. The calculations are based on the recent assessment involving all three ternary subsystems, a quaternary liquid approximated as a mixture of Mn, MnO, Mn₂O₃, SrO and Bi₂O₃ species with binary Redlich–Kister coefficients and the perovskite phase described in terms of a point defect model allowing Sr²⁺ for Bi³⁺ substitution, oxygen vacancy formation and the related Mn³⁺/Mn⁴⁺ mixing on Mn-sublattice. The crystallization path and the composition of the crystallized solid solution are compared with single crystal growth experiments performed by self-flux method from a Bi-rich melt. The crystallization path obtained for a selected feed composition for which the largest and high quality single crystal have been grown, turns out to end very close to the global eutectic point.     

Synthesis and physical chemical properties of Ca-substituted LaTiO2N

Oxynitrides with the general formula La_1−xCa_xTiO_2+xN_1−x (x = 0, 0.3, 0.5, 0.7, 1.0) were synthesized by thermal ammonolysis of oxide precursors produced with a soft chemistry method. The crystallographic structure, optical properties and the thermal stability of the compounds were studied with X-ray diffraction, UV–vis spectroscopy and thermal analysis.

All materials crystallize in perovskite-type pseudo-cubic unit cell. It was found that the lattice parameter decreases with increasing Ca content, while the optical band gap width increases with increasing x. Thermal reoxidation studies of the synthesized materials reveal the formation of nitrogen rich intermediates. The decomposition rate of the intermediates was correlated with the structure of the final products. TEM studies show a preferred insertion direction of the nitrogen into the crystal lattice of the starting oxides. Ammonolysis with flux significantly changed the microstructure of the obtained oxynitrides.     

Hydrothermal synthesis and intercalation behavior of a layered titanium phosphate Ti2(H2PO4)(HPO4)(PO4)2 · 0.5C6N2H16, with an extended γ-phase intercalated into organic amine

With a hydrothermal technique, a layered titanium phosphate with the formula Ti₂(H₂PO₄)(HPO₄)(PO₄)₂ · 0.5C₆N₂H₁₆ (denoted TP-J2) has been prepared by treating the Ti/H₃PO₄/H₂O/1-methylpiperazine system directly. The as-synthesized products were characterized by powder X-ray diffraction, CP-MAS solid-state ³¹P NMR spectroscopy, thermogravimetric and differential thermal analyses (TG-DTA). The structure was solved by single-crystal X-ray diffraction analysis and it presents an extended γ-phase intercalated with organic amine. Crystal data: triclinic, , a = 8.106 (2) Å, b = 8.197 (2) Å, c = 11.658 (2) Å.  = 78.32 (3)°, β = 80.85 (3)°, γ = 77.90 (3)°, Z = 2. Additionally, the intercalation behavior of TP-J2 with n-alkyl monoamine (n = 2, 3, 4, 6, 8, 10 and 12) was investigated. Owing to the strong brønsted base, N,N′-dimethylpiperazine, resides in the interlayer, it presented unusual features of TP-J2 in contrast with that of γ-Tip.     

Sub-solidus phase equilibria in CeO2–SrO system

In this communication, we report on the synthesis and characterization of a series of compounds with the general composition Ce_1−xSr_xO_2−x (0.0≤x≤1.0), to establish a detailed phase relation in the CeO₂–SrO system. The X-ray diffraction (XRD) pattern of the each product was refined to determine the solid solubility and the homogeneity range. The solid solubility limit of SrO in CeO₂ lattice, under the slow cooled conditions, is represented as Ce_0.91Sr_0.09O_1.91 (i.e. 9 mol% of SrO). A careful delineation of the phase boundary revealed that the stoichiometric SrCeO₃, in fact, contains a little amount of CeO₂ also. The mono-phasic compound could be obtained at the nominal composition Sr_0.55Ce_0.45O_1.45. The nominal composition Sr₂CeO₄, under the heat treatment used in the present investigation, was a bi-phasic mixture of SrCeO₃ and SrO. No new ordered phases were obtained in this system.     

Conductivity, calorimetry and phase diagram of the NaHSO4–KHSO4 system

Physico-chemical properties of the binary system NaHSO₄–KHSO₄ were studied by calorimetry and conductivity. The enthalpy of mixing has been measured at 505 K in the full composition range and the phase diagram calculated. The phase diagram has also been constructed from phase transition temperatures obtained by conductivity for 10 different compositions and by differential thermal analysis. The phase diagram is of the simple eutectic type, where the eutectic is found to have the composition X(KHSO₄) = 0.44 (melting point ≈ 406 K). The conductivities in the liquid region have been fitted to polynomials of the form κ(X) = A(X) + B(X)(T − T_m) + C(X)(T − T_m)², where T_m is the intermediate temperature of the measured temperature range and X, the mole fraction of KHSO₄. The possible role of this binary system as a catalyst solvent is also discussed.     

A density functional study of N NQR parameters of imidazole derivatives and extrapolation to PfHRP2–Fe-PPIX complex

In this paper, density functional theory (DFT) was used to calculate ¹⁴N nuclear quadrupole coupling constants (NQCC), χ, and asymmetry parameters, η, for a series of imidazole derivatives: imidazole, 5-methylimidazole and histidine. These calculations were carried out with the PW91P86 method via the Gaussian 98 package. A systematic theoretical investigation of the different environmental effects on (χ, η) values of amino ¹⁴N1 and imino ¹⁴N2 of imidazole ring of these compounds, reveals that the local surrounding of nitrogen atoms play an important role in determining their χ and η values. Our calculations in solution show that adding explicit solvent molecules to the polarizable continuum model (PCM) has a strong effect on (χ, η) values, thereby indicating that for long-range effects, PCM, is not sufficient to describe the whole solvent effects. We also evaluate the influence of [Fe³⁺ (S = 1/2)] on the (χ, η) values of proximal and remote nitrogens of an axial ligand and compare with those of free ligands. The results show that Fe³⁺ has a strong effect on the (χ, η) values of proximal nitrogen unlike remote nitrogen. Finally, our results predict (χ = 1.56 MHz, η = 0.690) for proximal nitrogen and (χ = 2.75 MHz, η = 0.169) for remote nitrogen in PfHRP2–Fe³⁺-PPIX complex.     

Mechanical stability and transport properties of the Sn-promoted SrCo0.8Fe0.2O3−δ ceramic membrane

In this article, the phase compositions, thermal, mechanical and transport properties of both the SrCo_0.8Fe_0.2O_3−δ (SCF) and the SrCo_0.8Fe_0.1Sn_0.1O_3−δ (SSCF) ceramic membranes were investigated systematically. As compared with the SCF membrane, the SSCF one had a more promoted thermal shock resistance, which related to its small thermal expansion coefficient between them and an enhanced composite structure for it. For the SCF membrane, a permeation rate of 1.9 × 10⁻⁶ mol cm⁻² s⁻¹ was obtained at 1000 °C and under the oxygen partial pressure gradient of P_O2 (h)/P_O2 (l) = 0.209 atm/0.012 atm; however, the permeation rate was 2.5 × 10⁻⁶ mol cm⁻² s⁻¹ for the SSCF one in the same measuring condition. In addition, both peak values of total electrical conductivity (σ_e) for SSCF sample appeared with increasing temperature. The second peak value of σ_e for SSCF one was regarded as the contribution from its minor phase, which appeared with the mixed conducting behavior resulting from partly Co-dissolving into its lattice.     

Spectroscopic and structural analysis of Ca substituted La orthoferrite

Samples of orthoferrites La_1−xCa_xFeO₃ (0.15≤x≤0.45) were synthesized by double sintering ceramic technique. X-ray diffraction and infrared spectroscopy experiments were carried out and discussed for the investigated samples. The data showed the formation of single-phase orthorhombic structure of space group Pbnm. The FTIR spectra were performed in the region (1200–200 cm⁻¹). Four main absorption bands were present with some side bands and shoulders in the range (1200–400 cm⁻¹). Another four bands were appeared in the range (400–200 cm⁻¹). The positions, intensities and values of the absorptions bands vary depending on the Ca content in the samples. The first absorption band appeared at about 920 cm⁻¹ was assigned to the La–O stretching vibration.     

Mixed-metal cluster chemistry VI: Phosphine substitution at CpMoIr3(μ-CO)3(CO)8; X-ray crystal structure of CpMoIr3(μ-CO)3(CO)7(PPh3)

Reactions of CpMoIr₃(μ-CO)₃(CO)₈ (1) with stoichiometric amounts of phosphines afford the substitution products CpMoIr₃(μ-CO)₃(CO)_8−x (L)_x (L = PPh₃, x = 1 (2), 2 (3); L = PMe₃, x = 1 (4), 2 (5), 3 (6)) in fair to good yields (23–54%); the yields of both 3 and 6 are increased on reacting 1 with excess phosphine. Products 2–5 are fluxional in solution, with the interconverting isomers resolvable at low temperatures. A structural study of one isomer of 2 reveals that the three edges of an MoIr₂ face of the tetrahedral core are spanned by bridging carbonyls, and that the iridium-bound triphenyiphosphine ligates radially and the molybdenum-bound cyclopentadienyl coordinates axially with respect to this Molr₂ face. Information from this crystal structure, ³¹P NMR data (both solution and solid-state), and results with analogous tungsten—triiridium and tetrairidium clusters have been employed to suggest coordination geometries for the isomeric derivatives.     

Preparation of epitaxial La0.6Ca0.4Mn1−xFexO3 (x = 0, 0.2) thin films: Variation of the oxygen content

Perovskite thin films with a nominal composition of La_0.6Ca_0.4Mn_1−xFe_xO₃ (x = 0, 0.2) were deposited by pulsed reactive crossed beam laser ablation. The film properties, such as electrical conductivity and magnetoresistance are studied as a function of the oxygen content and substrate type. The oxygen content of the thin films was determined by Rutherford Backscattering and controlled by varying the background gas pressure, pressure of the gas pulse and by using alternatively O₂ and N₂O as the gas pulse.

LaAlO₃ and SrTiO₃ were used as substrates at deposition temperature of 650 °C. The grown films were analyzed by X-ray diffraction in order to optimize the growth conditions, i.e. to obtain epitaxial thin films. Thin films doped with 20% Fe were grown under the same experimental conditions as the undoped LCMO films and the effect of the doping on the structural and transport properties of the thin films has been investigated.

The temperature of the metal–insulator transition was measured as a function of the oxygen content and substrate type.     

I NQR and spectroscopic investigation of impurity-doped and mixed lithium iodate Li1−xHxIO3 crystals

The ¹²⁷I NQR, IR absorption and Raman spectra of impurity-doped and mixed lithium iodate Li_1−xH_xIO₃ crystals grown from water solutions with different LiIO₃/HIO₃ ratios were investigated depending on the content of the impurity hydrogen x. The NQR results suggested that, at small concentration of doping iodic acid x<0.22, the lattice dynamics of the crystal grown from water solution changes significantly though the crystal retains hexagonal symmetry. Spectroscopic studies are compatible with average hexagonal symmetry of the grown doped crystals. From the results of Raman studies at room temperature and 100 K, the concentration range of hydrogen dopant 0.22<x<0.36 was found where disordered solid solution crystals Li_1−xH_xIO₃ are formed.     

Oxygen permeation study in a tubular Ba0.5Sr0.5Co0.8Fe0.2O3-δ oxygen permeable membrane

Dense tubular Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ (BSCFO) membranes were successfully prepared by the plastic extrusion method. The oxygen permeation flux was determined at different oxygen partial pressures in the shell side and different temperatures between 700 and 900 °C. The oxygen vacancy diffusion coefficients (D_v) at different temperatures were calculated from the dependence of oxygen permeation flux on the oxygen partial pressure term based on the surface current exchange model. No unsteady-state of oxygen permeation flux was observed at the initial stage in our experiments. The reason is the equilibrium time is too short (less than 10 min) to observe the unsteady-state in time. The increase of the helium flow rate can increase the oxygen permeation flux, which is due to the decrease of the oxygen partial pressure in the tube side with increasing of the helium flow rate. The oxygen permeation flux can also be affected by the air flow rate in the shell side when the air flow rate is lower than 150 ml/min. But the oxygen permeation flux is insensitive to the air flow rate when the air flow is higher than 150 ml/min. The membrane tube was operated steadily for 150 h with oxygen permeation flux of 1.12 ml/(cm² min) at 875 °C. X-ray diffraction (XRD) and energy dispersive spectroscopy (EDS) analysis showed that both the surface exposed to air and the surface exposed to helium of the BSCFO membrane tube after permeation for 150 h are similar to the fresh membrane tube in composition and structure. These results indicated that the membrane tube exhibits high structure stability.