A new ion imprinted polymer based on Ru(III)-thiobarbituric acid complex for solid phase extraction of ruthenium(III) prior to its determination by ETAAS

A new ruthenium ion imprinted polymer was prepared from the Ru(III) 2-thiobarbituric acid complex (the template), methacrylic acid or acrylamide (the functional monomers), and ethylene glycol dimethacrylate (the cross-linking agent) using 2,2′-azobisisobutyronitrile as the radical initiator. The ion imprinted polymer was characterized and used as a selective sorbent for the solid phase extraction of Ru(III) ions. The effects of type of functional monomer, sample volume, solution pH and flow rate on the extraction efficiency were studied in the dynamic mode. Ru(III) ion was quantitatively retained on the sorbents in the pH range from 3.5 to 10, and can be eluted with 4 mol L^?1 aqueous ammonia. The affinity of Ru(III) for the ion imprinted polymer based on the acrylamide monomer is weaker than that for the polymer based on the methacrylic acid monomer, which therefore was used in interference studies and in analytical applications. Following extraction of Ru(III) ions with the imprint and their subsequent elution from the polymer with aqueous ammonia, Ru(III) was detected by electrothermal atomic absorption spectrometry with a detection limit of 0.21 ng mL^?1. The method was successfully applied to the determination of trace amounts of Ru(III) in water, waste, road dust and platinum ore (CRM SARM 76) with a reproducibility (expressed as RSD) below 6.4 %.

Novel Imprinted Polymer for the Preconcentration of Cadmium with Determination by Inductively Coupled Plasma Mass Spectrometry

A novel Cd(II)-imprinted polymer was prepared with chemical immobilization using N-methacryloyl-L-Histidine as a vinylated chelating agent for online solid-phase extraction of Cd(II) for determination by inductively coupled plasma mass spectrometry. The Cd(II)–monomer complex was synthesized and copolymerized through bulk polymerization method in the presence of ethyleneglycoldimethacrylate cross-linker. The resulting polymer was leached with 1.0?mol?L^?1 HNO₃ to generate the cavities in the polymer for Cd(II) ions. The experimental conditions, including load pH, solution flow rate, and eluent concentration for effective sorption of Cd(II), were optimized using a minicolumn of the imprinted polymer. A volume of 5.0?mL sample 5?µg?L^?1 Cd(II) solution at pH 6.5 was loaded on the column at 2.0?mL?min^?1 using a sequential injection system followed by elution with 1.0?mL of 0.75?mol?L^?1 HNO₃. The relative selectivity coefficients of the imprinted polymer for Cd(II) were 38.5, 3.5, 3.0, 2.5, and 6.0 in the presence of Cu(II), Ni(II), Zn(II), Co(II), and Pb(II), respectively. Computational calculations revealed that the selectivity of the imprinted polymer was mediated by the stability of Cd(II)–N-methacryloyl-L-Histidine complex which was more stable than commonly used monomers including 4-vinyl pyridine, methacrylic acid, and vinylimidazole. The detection limit and relative standard deviation were 0.004?µg?L^?1 and 3.2%, respectively. The method was validated by the analysis of seawater certified reference material (CASS-4) and successfully used for the determination of Cd(II) in coastal seawater and estuarine water.     

Solid phase extraction of Pd(II) on a newly synthesized chelating resin prior to determination by flame atomic absorption spectrometry

A new solid phase extraction method for the separation and preconcentration of Pd(II) was developed. As solid phase material, a new chelating polymer, poly [N-(4-bromophenyl)-2-methacrylamide-co-2-acrylamido-2-methyl-1-propanesulfonic acid - co-divinylbenzene] was synthesized. The parameters such as the effect of pH, eluent type, volume and concentration, flow rate of sample solution, sample volume and effect of interfering ions for the preconcentration of Pd(II) were investigated. The optimum pH was found to be 9. Eluent for quantitative elution was 10 mL of 1 mol L^?1 HCl. The preconcentration factor of the method was 75. At optimum conditions, the recovery for Pd(II) was found to be 101?±?4%. The limit of detection (3σ) was 1.1?µg L^?1. The method was applied to the determination of palladium in tap water and converter samples with satisfactory results.     

Synthesis and application of a nanoporous ion‐imprinted polymer for the separation and preconcentration of trace amounts of vanadium from food samples before determination by electrothermal atomic absorption spectrometry

A vanadium ion‐imprinted polymer was synthesized in the presence of V(V) and N‐benzoyl‐N‐phenyl hydroxyl amine using 4‐vinyl pyridine as the monomer, ethylene glycol dimethacrylate as the cross linker and 2,2’‐azobis(isobutyronitrile) as the initiator. The imprinted V(V) ions were completely removed by leaching the polymer with 5 mol/L nitric acid, and the polymer structure was characterized by Fourier transform infrared spectroscopy and scanning electron microscopy. The ion‐imprinted polymer was used as the sorbent in the development of the solid‐phase extraction method for V(V) prior to its determination by electrothermal atomic absorption spectrometry. The maximum sorption capacity for V(V) ions was 26.7 mg/g at pH 4.0. Under the optimum conditions, for a sample volume of 150.0 mL, an enrichment factor of 289.0 and a detection limit of 6.4 ng/L were obtained. The developed method was successfully applied to the determination of vanadium in parsley, zucchini, black tea, rice, and water samples.     

Recycling of Palladium and Selected Metal Ions from Simulated Spent Catalysis Waste Solution Using Novel Dithiodiglycolamides Derivatives

The present study focusing on design and evaluation of series of eight new structurally related dithiodiglycolamides (DTDGA) as a novel promising solvent extraction reagents. The influence of the nature of the alkyl chain on the distribution ratio of Pd(II) was investigated. Both N, N-di-hexyl-N′, N′-di-octyldithiodiglycolamide (DHDODTDGA) and N, N-di(2-ethylhexyl)-N′, N′-dioctyldithiodiglycolamide (DEHDODTDGA) were chosen and applied to perform the selective recovery and separation of Pd(II) from certain commonly associated elements such as Pt(IV), Rh(III), Fe(III), Cr(II), Mn(II), Zr(II), and Ni(II) contained in hydrochloric acid solutions using n-dodecane as diluent. A systematic investigation has been carried to understand the extraction behavior of Pd(II) using the synthesized extradant. The extraction equilibrium of Pd(II) was obtained within 3–4 min. The investigated extractants showed quantitative extraction of Pd(II) at ～ 4 M HCl. The main extracted species of Pd(II) at 3.5 M HCl is Pd.DTDGA and IR spectra of the extracted species have been also studied. The other investigated metals ions were found poorly extracted under the same extraction contortions. Quantitative back-extraction of Pd(II) in the organic phase was obtained in single contact using thiourea solution. The obtained results make the novel synthesized ligands a promising candidates for selective recovery and separation of Pd(II) from spent catalyst dissolver (SSCD) solution.

     

Xylenol Orange‐Functionalized Halloysite Nanotubes as a Novel Adsorbent for Selective Solid‐phase Extraction and Determination of Trace Noble Elements

A novel method using xylenol orange‐modified halloysite nanotubes as a solid‐phase sorbent has been developed for the simultaneous preconcentration and separation of trace Au(III ) and Pd(II ) prior to their determination by inductively coupled plasma‐atomic emission spectrometry (ICP‐AES ). The experimental effects of pH , the amount of adsorbent, sample flow rate, sample volume, interfering ions, and the elution condition were investigated in detail. Au(III ) and Pd(II ) were retained on the column at pH 3, and eluted with 2.0 mL of 1.0 mol/L HCl + 2% CS (NH₂ )₂ solution. Common interfering ions did not have any impact on the adsorption, separation, and determination. An enrichment factor of 150 was obtained. The maximum adsorption capacities of the adsorbent were 41.63 and 47.82 mg/g for Au(III ) and Pd(II ), respectively, under the optimum conditions. By the definition of IUPAC , the detection limits (3σ ) of this method for Au(III ) and Pd(II ) were 0.31 and 0.27 ng/mL , and the relative standard deviations (RSDs ) were 2.7 and 3.2%, respectively (n = 8). This newly developed method was verified by certified reference materials, and has been successfully applied to the determination of trace Au(III ) and Pd(II ) in mine samples with satisfactory results. It can be confidently predicted that the method can be used for the determination trace Au(III ) and Pd(II ) in other real samples because of its high selectivity, sensitivity, and reproducibility.     

Selective extraction of clonazepam from human plasma and urine samples by molecularly imprinted polymeric beads

A molecularly imprinted polymer (MIP) based on free‐radical polymerization was prepared with 1‐(N,N‐biscarboxymethyl)amino‐3‐allylglycerol and N,N‐dimethylacrylamide as functional monomers, N,N‐methylene diacrylamide as the cross‐linker, copper ion‐clonazepam as the template and 2,2‐azobis(2‐methylbutyronitrile) as the initiator. The imprinted polymer was characterized by Fourier transform infrared spectroscopy, elemental analysis, thermogravimetric analysis, and SEM. The MIP of agglomerated microparticles with multipores was used for SPE. The imprinted polymer sorbent was selective for clonazepam. The optimum pH and sorption capacity were 5 and 0.18 mg/g at 20°C, respectively. The profile of the drug uptake by the sorbent reflects good accessibility of the active sites in the imprinted polymer sorbent. The MIP‐SPE was the most feasible technique for the extraction of clonazepam with a high recovery from human plasma and urine samples.     

Determination of platinum and palladium in road dust after their separation on immobilized fungus by electrothermal atomic absorption spectrometry

A flow solid phase extraction procedure based on biosorption of Pt(IV) and Pd(II) on Aspergillus sp. immobilized on cellulose resin Cellex-T was proposed for the separation and preconcentration of Pt and Pd before their determination by electrothermal atomic absorption spectrometry (ETAAS). The analytical conditions including sample pH, eluent type, flow rates of sample and eluent solutions were examined. The analytes were selectively retained on the biosorbent in acidic medium (pH 1) and subsequently eluted from the column with 1 mL of thiourea solution (0.25 mol L^− 1 thiourea in 0.3 mol L^− 1 HCl). The reproducibility of the procedure was below 5%. The limit of detection of the method was 0.020 ng mL^− 1 for Pt and 0.012 ng mL^− 1 for Pd. The method validation was performed by analysis of certified reference materials BCR-723 (tunnel dust) and SARM-76 (platinum ore). The developed separation procedure was applied to the determination of Pt and Pd in road dust samples by ETAAS.The applied biosorbent is characterized by high sorption capacity: 0.47 mg g^− 1 for Pt and 1.24 mg g^− 1 for Pd.     

Selective solid phase extraction of platinum on an ion imprinted polymers for its electrothermal atomic absorption spectrometric determination in environmental samples

An ion-imprinted polymer (IIP) was obtained by copolymerization of methacrylic acid (as a functional monomer) and ethylene glycol dimethacrylate (as a crosslinking agent) in the presence of various chelators for Pt(II) ion and using 2,2??-azo-bis-isobutyronitrile as the initiator. Specifically, acetaldehyde thiosemicarbazone (AcTSn) and benzaldehyde thiosemicarbazone (BnTSn) were used as chelators. The IIPs were applied as sorbents for solid-phase extraction of Pt(II) and Pt(IV) ions from aqueous solutions. The effects of acidity and flow rate of the sample, of elution conditions and of potentially interfering ions were investigated. The imprinting effect of analyte is clearly demonstrated by the fact that only the IIP is capable of quantitative retention of Pt(II) and Pt(IV) ions. The method works best in the pH range from 0.5 to 1 and from 3.5 to 9.5. The ions can be recovered with an acidic solution of thiourea. The Pt-AcTSn polymer displays better sorption properties for the separation of analytes. The selectivity coefficients of the Pt-AcTSn and control polymers for Pt(IV) in the presence Pd(II), Rh(III), Ru(III), Al(III) and Cu(II) were calculated, and the sorbent capacity for Pt(IV) was found to be 4.56???g?g?^-1. The method was successfully applied to the determination of Pt(IV) by electrothermal atomic absorption spectrometry in tap water, tunnel dust and anode slime samples.

Novel adsorptive materials by adenosine 5ʹ‐triphosphate imprinted‐polymer over the surface of polystyrene nanospheres for selective separation of adenosine 5ʹ‐triphosphate biomarker from urine

In this study, we have developed a method to assess adenosine 5?‐triphosphate by adsorptive extraction using surface adenosine 5′‐triphosphate‐imprinted polymer over polystyrene nanoparticles (412 ± 16 nm) for selective recognition/separation from urine. Molecularly imprinted polymer was synthesized by emulsion copolymerization reaction using adenosine 5′‐triphosphate as a template, functional monomers (methacrylic acid, N‐isopropyl acrylamide, and dimethylamino ethylmethacrylate) and a crosslinker, methylenebisacrylamide. The binding capacities of imprinted and non‐imprinted polymers were measured using high‐performance liquid chromatography with UV detection with a detection limit of 1.6 ± 0.02 µM of adenosine 5′‐triphosphate in the urine. High binding affinity (Q_MIP, 42.65 µmol/g), and high selectivity and specificity to adenosine 5′‐triphosphate compared to other competitive nucleotides including adenosine 5?‐diphosphate, adenosine 5?‐monophosphate, and analogs such as adenosine, adenine, uridine, uric acid, and creatinine were observed. The imprinting efficiency of imprinted polymer is 2.11 for urine (Q_MIP, 100.3 µmol/g) and 2.51 for synthetic urine (Q_MIP, 48.5 µmol/g). The extraction protocol was successfully applied to the direct extraction of adenosine 5′‐triphosphate from spiked human urine indicating that this synthesized molecularly imprinted polymer allowed adenosine 5′‐triphosphate to be preconcentrated while simultaneously interfering compounds were removed from the matrix. These submicron imprinted polymers over nano polystyrene spheres have a potential in the pharmaceutical industries and clinical analysis applications.     

Determination of methylmercury by electrothermal atomic absorption spectrometry using headspace single-drop microextraction with in situ hydride generation

A new method is proposed for preconcentration and matrix separation of methylmercury prior to its determination by electrothermal atomic absorption spectrometry (ETAAS). Generation of methylmercury hydride (MeHgH) from a 5-ml solution is carried out in a closed vial and trapped onto an aqueous single drop (3-μl volume) containing Pd(II) or Pt(IV) (50 and 10 mg/l, respectively). The hydrogen evolved in the headspace (HS) after decomposition of sodium tetrahydroborate (III) injected for hydride generation caused the formation of finely dispersed Pd(0) or Pt(0) in the drop, which in turn, were responsible for the sequestration of MeHgH. A preconcentration factor of ca. 40 is achieved with both noble metals used as trapping agents. The limit of detection of methylmercury was 5 and 4 ng/ml (as Hg) with Pd(II) or Pt(IV) as trapping agents, and the precision expressed as relative standard deviation was about 7%. The preconcentration system was fully characterised through optimisation of the following variables: Pd(II) or Pt(IV) concentration in the drop, extraction time, pH of the medium, temperatures of both sample solution and drop, concentration of salt in the sample solution, sodium tetrahydroborate (III) concentration in the drop and stirring rate. The method has been successfully validated against two fish certified reference materials (CRM 464 tuna fish and CRM DORM-2 dogfish muscle) following selective extraction of methylmercury in 2 mol/l HCl medium.     

A novel Pb(II)-imprinted IPN for selective preconcentration of lead from water and sediments

A novel adsorbent Pb(II)-imprinted interpenetrating polymer network (IPN) of epoxy resin-triethylenetetramine and lead methacrylate-acrylamide-1,4-butanedioldiacrylate (BDDA) was synthesized by the metal ionic imprinted polymer (MIIP) technique. The IPN was prepared by in situ sequential polymerization, and the coordination interaction of Pb(II) and functional groups of the IPN adsorbent was discussed using FT-IR spectra. The characters of the IPN were investigated by a series of experiments. The experimental results show that trace Pb(II) ions can be quantitatively preconcentrated at pH 4.0 with recoveries >95%. The maximum static adsorption capacity of the ion-imprinted adsorbent was 138.6?mg?g^?1. The imprinted IPN has a higher adsorption capacity and selectivity towards Pb(II). Moreover, the Pb(II)-imprinted IPN shows superior reusability and stability. The precision (R.S.D.) for 11 replicate adsorbent extractions of 20?ng?mL^?1 Pb(II) was 2.9%. The accuracy of the proposed procedure was verified by analysing three standard reference materials. The prepared ion-imprinted IPN adsorbent was applied to three natural samples and also yielded satisfactory results. That is to say, the Pb(II)-imprinted IPN is suitable for environmental Pb(II) ionic selective removal as an SPE adsorbent.     

Graphene-modified Monolithic Capillary Column for the Microextraction of Trace Benzodiazepines in Biological Samples

A graphene monolithic column was fabricated in a capillary using π-electron-rich poly(N-vinylcarbazole-divinylbenzene) as the supporter through in situ one-step polymerization for the enrichment of trace benzodiazepines in biological samples. This new three-dimensional monolith showed uniformity and a continuous column bed; more importantly, it retained the unique properties of graphene that are typically associated with individual graphene sheets. Based on the large delocalized π-electron system, graphene forms π–π stacking interactions with benzodiazepines and benzene rings of poly(N-vinylcarbazole-divinylbenzene), which not only enhance the extraction performance for benzodiazepines compared to the neat polymer but also provide chemical stability of the graphene monolith. Moreover, several factors likely to affect the extraction, including ionic strength, sample pH, sample volume, and eluant volume were studied in detail. The optimized method gave a linear range of 0.005–1?ng?mL^?1, and detection limits of 1.12–2.35?ng?L^?1. Finally, the graphene monolith was successfully applied to the separation and enrichment of benzodiazepines from urine and hair samples coupled with high-performance liquid chromatography–mass spectrometry. The recoveries were in the range of 78.6–85.6% for urine and 87.2–94.3% for hair with relative standard deviations of 3.4–6.9 and 2.9–8.3%, respectively.     

Microwave-assisted UV-digestion procedure for the accurate determination of Pd in natural waters

A procedure was developed for the selective determination of Pd in environmental aquatic solutions. The method is based on a preliminary microwave-assisted UV-digestion for the degradation of dissolved organic material, and the subsequent determination of Pd using a recently presented enrichment procedure with ETAAS detection. Due to the simultaneous use of microwave and UV irradiation only extremely small quantities of hydrogen peroxide were necessary to yield a quantitative degradation of interfering organic ligands. Thus the on-line pre-concentration of Pd in the digested samples using the complexing agent N,N-diethyl-N′-benzoylthiourea was possible without any further sample pre-treatment. Using a sample volume of 1.57 ml for FI-ETAAS analysis a limit of detection of 15 ng l⁻¹ was obtained for the combined procedure, with a relative standard deviation being not more than 4.9%. The method was applied to quantify the water-soluble fraction of Pd in urban road dust. Extractions with a rain sample of pH 5.9 revealed that an average of 2.2% (n = 8) of the total Pd present in urban road dust was water soluble.     

Selective back-extraction and preconcentration of zinc(II) from metal-1,3,5-triketone extracts prior to its determination by flame atomic absorption spectrometry

A simple back-extraction method was developed for the separation and preconcentration of trace levels of zinc from different matrices. Ethyl-2-(4-methoxybenzoyl)-3-(4-methoxyphenyl)-3-oxopropanoylcarbamate (EMPC) was used as a new complexing agent for the extraction of zinc(II) from the aqueous sample phase to the methyl isobutyl ketone (MIBK) phase as Zn(EMPC)₂ complexes. The Zn(II) can be selectively stripped with 1?mL of 0.5?mol?L^?1 HCl from Mⁿ⁺(EMPC)_n complexes [Ag(I), Al(III), Cd(II), Cr(III), Cu(II), Fe(II), Fe(III), Mn(II), Ni(II), Pb(II) and Pd(II)] which dissolved in MIBK phase. Some experimental parameters, which are important for the whole extraction process, including pH, sample volume, shaking time, amount of the EMPC reagent, amount of MIBK, ionic strength, and type of back-extractant were investigated. The recovery for Zn(II) was greater than 95%. The detection limit of the method was found to be 0.2?µg?L ^{? 1} and the relative standard deviation as 6.4%. The concentrations of Zn(II) in the certified reference materials (LGC6019 river water and NIST-1547 peach leaves) by the presented method were in good agreement with the certified values. The proposed method was succesfully applied to the determination of zinc in some natural waters, rice, hair, soil, and tea samples.     

Selective and sensitive determination of protoberberines by capillary electrophoresis coupled with molecularly imprinted microextraction

In this work, we developed a novel molecularly imprinted solid‐phase microextraction with capillary electrophoresis method for the selective extraction and determination of protoberberines in complicated samples. The imprinted monolith was prepared in a micropipette tip‐based device by using acrylamide as the functional monomer, ethyleneglyoldimethacrylate as the cross‐linker and dimethylsulfoxide as the porogen, and exhibited an imprinting factor of 2.41 to berberine, 2.36 to palmatine and 2.38 to jatrorrhizine. Good capillary electrophoresis separation was achieved by using 20 mM phosphate buffer at pH 7 as running buffer with the addition of organic modifier of 10% methanol. Parameters such as sample pH value, sample flow rate and sample volume were investigated for imprinted monolith‐based solid‐phase microextraction. An imprinted solid‐phase microextraction with capillary electrophoresis method was developed, the method showed a wide linear range (0.3–50 μg/mL), good linearity (R² ≥ 0.9947) and good reproducibility (relative standard deviations ≤ 0.73%), the limit of detection was as low as 0.1 μg/mL, which was lower than some reported methods based on capillary electrophoresis for protoberberines. The method has been applied for determination of three common protoberberines in Cortex Phellodendri Chinensis, by using a molecularly imprinted monolith as the selective sorbent, most of the matrices in the Cortex Phellodendri Chinensis sample were removed and three protoberberines were selectively enriched and well determined.     

Novel ion-imprinted polymer coated on nanoporous silica as a highly selective sorbent for the extraction of ultratrace quantities of gold ions from mine stone samples

We have developed a gold ion-imprinted polymer (GIP) by incorporating a dipyridyl ligand into an ethylene glycol dimethacrylate matrix which then was coated onto porous silica particles. The material was used for the selective extraction of ultratrace quantities of gold ion from mine stones, this followed by its quantitation by FAAS. The effects of concentration and volume of eluent, pH of the solution, flow rates of sample and eluent, and effect of potentially interfering ions, especially palladium and platinum, was investigated. The limit of detection is <0.2 ng?mL^?1, the precision (RSD%) is 1.03 %, and recoveries are >99 %. In order to show the high selectivity and efficiency of the new sorbent, the results were compared to those obtained with more simple sorbents possessing the same functional groups. The accuracy of the method was demonstrated by the accurate determination of gold ions in a certified reference material. To the best of our knowledge, there is no report so far on an imprint for gold ions that has such a selectivity over Pd(II) and Pt(II) ions.

Highly efficient adsorbing noble metal ions by 3,4-dihydroxycinnamic acid-modified activated carbon

A method was established for the preconcentration of trace Au(III), Pd(II) and Pt(IV) by activated carbon modified with 3,4-dihydroxycinnamic acid. The separation and preconcentration conditions of analytes were investigated, such as effects of pH, the contacting time, the sample ?ow rate and volume, the elution condition and the interfering ions. At a pH of 1.0, the maximum static sorption capacity of the sorbent was found to be 374.8, 96.6 and 137.5 mg g^?1 for Au(III), Pd(II) and Pt(IV), respectively. The adsorbed metal ions were effectively eluted with 2.0 mL of 4% thiourea in 0.5 M HCl solution and determined by inductively coupled plasma optical emission spectrometry. The detection limit (3σ) of this method defined by IUPAC was found to be 0.12, 0.18 and 0.32 ?g L^?1 for Au(III), Pd(II) and Pt(IV), respectively. The relative standard deviation (RSD) was lower than 3.0% (n = 8) towards standard solutions. The method has been validated by analysing certified reference materials and successfully applied to the determination of trace Au(III), Pd(II) and Pt(IV) in road sediments samples.     

Benign synthesis of quinolinecarboxamide ligands,H2bqbenzo and H2bqb and their Pd(II) complexes: X-ray crystal structure,electrochemical and antibacterial studies

Two carboxamide ligands, H₂bqbenzo {3,4-bis(2-quinolinecarboxamido)benzophenone} and H₂bqb {N,N′-bis[(2-quinolinecarboxamide)-1,2-benzene]}, have been prepared using tetrabutylammonium bromide as an environmentally benign reaction medium. Two new Pd(II) complexes, [Pd^II(bqbenzo)] (1) and [Pd^II(bqb)] (2), have been synthesized, characterized, and their structures determined by single crystal X-ray diffraction. The di-anionic ligands, bqbenzo^2? and bqb^2?, are coordinated via two N_amide atoms and the nitrogens of the two quinoline rings, with Pd?N_amide < Pd–N_quinoline bond lengths. The geometry around palladium(II) in both complexes is distorted square planar. The electrochemical behaviors of the ligands and their Pd(II) complexes have been investigated by cyclic voltammetry in DMF. An irreversible Pd^II/I reduction is observed at ?1.06 V for 1 and at ?1.177 V for 2, indicating the influence of the R substituent on the central phenyl ring of carboxamide ligands on the Pd^II/I reduction potential. The ligands and palladium complexes were also screened for in vitro antibacterial activity. The Pd(II) complexes show strong biological activity against S.typhi and E.coli as Gram ?ve and B.cereus and S.aureus as Gram +ve bacteria comparable to the antibiotic penicillin. The antibacterial results also reveal that coordination of Pd(II) significantly improves the activity.     

Separation and pre-concentration of palladium(II) from environmental and industrial samples by formation of a derivative of 1,2,4-triazole complex on Amberlite XAD–2010 resin

A simple separation/pre-concentration method was developed for extraction of Pd(II) in various environmental samples, based on its adsorption of 4–phenyl–5–{[(4–phenyl–5–pyridin–4–yl–4H–1,2,4–triazole–3–yl)thio]methyl}–4H–1,2,4–triazole–3–thyol (PPTTMET) complex on Amberlite XAD–2010 resin in a mini column. The ligand has high affinity for Pd(II) among many other metals that are taken into consideration. The flame atomic absorption spectrometry is employed to determine the concentration of Pd(II). The optimum working conditions which were determined are as follows: 0.05?mol?L^?1 HNO₃ as working medium, 1.0?mol?L^?1 HCI in acetone as elution solvent, 0.75?mg of PPTTMET amount and 750?mL of sample volume. The system was independent from the flow rates between 3.1 and 23.1?mL?min^?1. The Pd(II) adsorption capacity of Amberlite XAD–2010 resin was found to be 12.8?mg?g^?1 and the enrichment factor was calculated as 375. The method was successfully applied for the determination of Pd(II) in motorway dust samples, anodic sludge, gold ore, industrial electronic waste materials and various water samples.