Spectrophotometric Catalytic Determination of Trace Amounts of Selenium Based on the Reduction of Azurea by Sulphide

ABSTRACT

A sensitive catalytic kinetic spectrophotometric method for determining ng ml^?1 concentrations of selenium is described. The method, based on the catalytic effect of Se (IV) on the reduction of azureA by sulphide, is monitored spectrophotometrically at 600 nm. The linearity range of the calibration graph is dependent on the concentration of sulphide. The variables affecting the rate of the reaction were investigated and the optimum conditions were established. The method is simple, rapid, precise, sensitive, free from many interferences and is widely applicable. The limit of detection is 2.5ng ml^?1 of Se. The relative standard deviation of seven determinations of 100 ng ml^?1 Se was 1.5%. The method was applied to the determination of selenium in spiked water, Kjeldahl tablets, synthetic samples and health care products.     

Analysis of Metal Ions in Environmental Samples - III Synergistic Determination of Vanadium (V) As its Mixed Complex with N-0-Methoxyphenyl-2-Thenohydroxamic Acid and 3-(0-Carboxyphenyl)-1-Phenyltriazine-N-0Xide

Abstract

A highly sensitive, selective, and rapid method for the spectrophotometry determination of vanadium(V) at trace levels is described. The method is based on the selective extraction of vanadium(v) from strongly acidic (3–6 M hydrochloric acid) met ium with solution of N-0-methoxyphenyl-2- thenohydroxamic acid (0MTHA) in chloroform. The extract is then equilibrated with 3-(0-carboxyohenyl)-1-phenyltriazine-N-oxide(CPPTNO) at pH ? 1.5 and the resulting colour is measured at 445 nm. The colour system obeys Beer's law over the range 0–20 -μg/ml of vanadium; the molar absorptivityat the wavelength of maximum absorption (445 nm), and the Sandell sensitivity of the method are 1.1 × 10⁴1. mole^?1 cm^?1 and 0.005 μg/ml respectively.     

Selective detection of F− by chromogenic tetrazole receptor

A chromogenic anion host 4, containing two amide functionalities linked to azo dye and tetrazole rings, was synthesised and its complexes with various anions were investigated. The results show that receptor 4 can recognise selectively biologically important F^?  ion. The binding affinity for F^?  was investigated by naked-eye colour change, UV–vis and ¹H NMR spectroscopy. Addition of F^?  ion in CH₃CN and Dimethyl sulfoxide to receptor 4 causes a change in colour of the solution from colourless to yellow. The stoichiometry for host:anion is 1:1. Furthermore, receptor 4 was used as an ion carrier in ion-selective membrane electrodes. Selectivity of this membrane was studied towards various anions in water solution. Binding behaviour of receptor 4 towards several anions (Cl^? , F^? , Br^? , I^? ) has been investigated using density functional theory calculations.     

Indole-based distinctive chemosensors for ‘naked-eye’ detection of CN and HSO4−, associated with hydrogen-bonded complex and their DFT study

Colorimetric detection of anions (HSO₄^? and CN^?) was achieved via analyte triggered colour changing of the dipodal and tripodal sensors in CH₃CN–H₂O (1:1). The sensors exhibited very sharp visual colour changes and fluorescence quenching–enhancing effect upon addition of the HSO₄^? and CN^?. The large downfield shift of the NH proton signals in ¹H-NMR complexation studies and quantum chemical DFT calculations proved the formation of hydrogen-bonded complexes where no proton transfer mechanism was found.     

Diazotised 4-Nitroaniline as a Chromogenic Reagent for the Determination of Indole Derivatives in Certain Pharmaceutical Preparations

Abstract

A sensitive colorimetric method has been devised for microdetermination of six indole derivatives; ergotamine tartrate, methylergometrine maleate, dihydroergocornine methanesulphonate, dihydroergocristine methanesulphonate, dihydroergocryptine methanesulphonate and pindolol, both in pure form and in pharmaceutical preparations. The method is based on the reaction of indole moiety with diazotised 4-nitroaniline in buffer solution of pH 6 to produce a stable yellow monoazo dye. Beer's law is obeyed over final concentration ranges 8–32 μgm1^?1 for ergotamine tartrate, 4–48 μgml^?1 for methylergometrine maleate, 8–56 μgml^?1 for dihydro-ergot alkaloids and 1–10 μgml^?1 for Pindolol with apparent molar absorptivity range (7.62 × 10³?2.61 × 10⁴) 1.mole^?1.cm^?1. A study has been made to determine the optimum conditions of the colour reaction.     

Cyclopentane-1,3-dione Bis (4-Methylthiosemicarbazone) Monohydrochloride as a Spectrophotometric Reagent for the Determination of Bromate in Perchloric Acid Medium

Abstract

Cyclopentane-1,3-dione bis (4-methylthiosemicarbazone) monohydrochloride produces coloured solutions with bromate ions in perchloric acid medium. The yellow colour obtained (molar absorptivity 1.8×10⁴ 1.mol^?1.cm^?1 at a wavelength of 400 mm) has been used for the spectrophotometric determination of trace amounts of bromate.     

Spectrophotometric catalytic determination of ultra-trace amounts of selenium based on the reduction of resazurin by sulphide

A sensitive catalytic method for determining ng ml^? concentration of selenium is described. The method is based on the catalytic action of Se(IV) on the reduction of resazurin by sulphide, monitored spectrophotometrically at 605 nm. The linearity range of the calibration graph is dependent on the concentration of sulphide. The variables affecting the rate of the reaction were investigated and the optimum conditions were established. The method is simple, rapid, precise, sensitive and widely applicable. As low as 8.0 × 10^?4 μg ml^?1 of selenium can be determined. The relative standard deviation of seven determination of 10 ng Se was 0.7%. The determination of Se(IV) in the presence of Se(VI) and the determination of total selenium are also described.     

Spectrophotometric Determination of Manganese with 4(5)-Imidazolealdoxime (Imalox)

Abstract

A method is described for the spectrophotometric determination of manganese by means of its complex with 4(5)-imidazolealdoxime, IMALOX, formed in alkaline medium. The colour system has its absorption maximum at 350 nm and obeys Beer's law over the range 0.8–8.0 μg of Mn per ml. The optimum range is 1–5 μg m^?1. The molar absorptivity is 7850 1 mol^?1 cm^?1. Relatively few ions interfere, and these can be masked with cyanide, tartrate and NTA. The experimental results have been critically analyzed and a comparison with the main spectrophotometric reagents for manganese is presented.     

Trace Analysis of Vanadium in Environment as its Ternary Complex with N-p Methoxyphenyl-2-Furylacrylohydroxamic Acid and 3-(o-Carboxyphenyl)-1-Phenyltriazine-N-Oxide

Abstract

A method is presented for the highly sensitive, selective, and rapid determination of vanadium (V) at sub-microgram levels in rocks, animal tissues, plant tissues and natural waters. The method is based on the selective extraction of vanadium (V) from strongly acidic (3-8 M hydrochloric acid) medium with solution of N-p-methoxyphenyl-2-furylacrylohydroxamic acid (MFHA) in chloroform. The reddish-violet extract (molar absorbance 8.6x10³ 1 mole^?1 cm^?1 at λ max 545 nm) is then equilibrated with 3-(o-carboxyphenyl)-1-phenyltriazine-N-oxide (CPPTNO) at pH = 1.5. The resulting ternary complex has enhanced colour (molar absorbance 1.4 × 10⁴ 1 mole^?1 cm^?1 at Λ max 450 nm). The ternary system obeys Beer's Law at 450 nm over the range 0-18 μ g/ml of vanadium. The extraction system achieves 20-fold enrichment of vanadium and enables the determination of the metal down to parts per billion (ng 1^?1) levels. The method tolerates the presence of a large number of anions and cations which are normally present with vanadium in rocks, plant tissues, animal tissues and natural waters. The applicability of the method was tested by the analysis of vanadium in these matrices. MFHA was selected from nine hydroxamic acids as it provided maximum sensitivity and selectivity.     

A simple Schiff base as selective and sensitive fluorescent-colorimetric hydrazine chemosensor

ABSTRACT

A new fluorescent-colorimetric chemosensor L has been synthesised by Schiff base condensation reaction between 1,8-diaminooctane and 4-nitro-benzaldehyde in very good yields. Its photo-luminescent properties and selective detection properties for hydrazine have been examined. The synthesised chemosensor exhibited highly selective fluorescence on-off response for hydrazine amongst a wide range of different metal cations, anions and amines, along with the bare eye colour change from colourless to yellow based on intermolecular hydrogen-bond interaction. The limit of detection of the chemosensor L was estimated as 9.77 × 10^?8 M or 3.12 × 10^?6 g L^?1 for hydrazine which is extremely below the limit set by the World Health Organization (WHO) and the binding stoichiometry was proposed to be 1 : 2 based on ¹H NMR spectroscopic techniques and the Job’s plot analysis. The proposed sensing mechanism is the hydrogen-bonding interaction which has further been established by Density Functional Theory (Functional Density Theory (DFT)) studies. This recognition feature of sensor L makes it an efficient chemosensor for hydrazine detection in different water samples.     

A highly selective and sensitive colorimetric chemosensor based on polyurethane foam impregnated with 3-methyl-2, 6-dimercapto-1,4-thiopyrone for on-site preconcentration and determination of palladium(II)

ABSTRACT

A new sorbent and chemosensor for highly selective and sensitive on-site preconcentration and colorimetric determination of Pd(II) was developed based on its reaction with 3-methyl-2,6-dimercapto-1,4-thiopyrone (MDT) immobilised onto polyurethane foam (PUF). Complexation of Pd(II) with MDT sorbed on PUF tablets leads to a contrast change in the sorbent colour from pale yellow to reddish-brown. The developed chemosensor is highly selective with respect to the transition and platinum group metals. It has a maximum sorption capacity of 17 µmol g^?1 for Pd(II). Reaction is possible in a strongly acidic medium (up to10 M HCl), and the properties of the chemosensor do not change during storage for a long time. The colorimetric response of the chemosensor was measured using red–green–blue (RGB) colour model. The dependence of the luminosity of the G channel on the Pd(II) concentration was linear in the concentration range from 0.3 to 64 µg L^?1 with a detection limit of 0.1 µg L^?1 (R² = 0.997). The colour scale for visual detection of Pd(II) was constructed in the concentration range of 0.02–0.64 mg L^?1 for the sorption from 20 mL of an aqueous sample. The accuracy of the developed methods was assessed by the analysis of a certified reference material (platinum–palladium alloy) and by comparison with the results of gravimetric or graphite furnace atomic absorption spectrometry (GFAAS) determination of Pd. The developed method was successfully applied to determine Pd in samples of mine water and road dust, in the electrolyte bath and in the sewage sludge of a palladium electroplating bath.     

Spectrophotometer Determination of Nitrite Using Salbutamol sulphate as a Reagent

Abstract

A simple spectrophotometric method for the trace determination of nitrite (NO^? ₂) is described. Nitrite is reacted with Salbutamal sulphate in acidic medium which gives a yellow colour in alkaline medium (?pH 7) and can be determined in the presence of several cations and anions. Beer's law is obeyed in the range of 1.8 to 27.6 ppm of nitrite with the molar absorptivity 1.8 × 10³ 1 × mole^?1 × cm^?1 at 4l0 nm. The proposed method can also be utilized for the determination of nitrate (NO^? ₃) after its reduction to nitrite. The method has been applied for the determination of various samples containing traces of nitrite.     

Rapid Extraction Spectrophotometric Determination of Platinum Using Anisaldehyde-4-Phenyl-3-Thiosemicarbazone as a Chromogenic Reagent

Abstract

The synthesis, spectral characteristics and analytical applications of anisaldehyde-4-phenyl-3-thiosemicarbazone (APT) are described. A simple, rapid, selective and sensitive spectrophotometric method for the determination of platinum was developed based on the colour reaction between platinum (IV) and anisaldehyde-4-phenyl-3-thio-semicarbazone (APT) in the pH range 1.7 - 3.0. The yellow coloured species has an absorption maximum at 360 nm. The complexation is complete within 1 min. A five-fold excess of the reagent is required for complete complex formation. Beer's law is obeyed over the concentration range 0.1 -20 ppm of Pt(IV). The mtilar absorptivity and Sandell's sensitivity are 1.58 × 10⁴ l. mol^?1 cm^?1 and 0.0123 ug of Pt(IV) cm^?2, respectively. The effects of pH, time concentration of reagent, order of addition of reagents and the interference from various ions were investigated. The method has been employed for the determination of platinum in synthetic mixtures whose composition correspond to some alloys.     

A revised method for the spectrophotometric determination of glyoxylic acid

The spectrophotometric determination of glyoxylic acid at 520 nm based on formation of the 1,5-diphenyl formazan derivative is revised. The colour can be developed at room temperature if the acid or its sodium salt is pure. The molar absorptivity is improved to 32 250 l mol^?1 cm^?1. The differences from the earlier procedures are discussed.     

A Sensitive Chemiluminescence Method for Cinchona Alkaloids

Abstract

Chemiluminescence (CL) was achieved by oxidation of sulphide with cerium(IV) in the presence of cinchona alkaloids (quinine, quinidine or cinchonine). The CL intensity was correlated with the concentration of each cinchona alkaloid. Based on this phenomenon, sensitive CL methods for these alkaloids were described. Quinine (4×10^?8～1×10^?4 g/ml), quinidine (1×10^?7 ～ 1×10^?3 g/ml) and cinchonine (1×10^?6 ～ 8×10^?4 g/ml) could be determined with detection limits of 1×10^?8 g/ml, 4×10^?8 g/ml and 6×10^?7 g/ml, respectively.     

Extraction,Spectrophotometric and Atomic Absorption Spectrophotometric Determination of Molybdenum with Caffeic Acid and Application in High Purity Grade Steel and Environmental Samples

Abstract

A new selective and sensitive method for extraction of yellow Mo (VI)-caffeic acid complex with a liquid ion exchanger, Aliquat 336 from 4.0 pH, and spectrophotometric determination of molybdenum in trace amounts is described. the molar absorptivity of the complex is 1.1 × 10⁵ 1 mol^?1 cm^?1 at 340 nm and the colour system obeys Beer's law in the range 0.04–0.99 ppm of Mo(VI). the molybdenum is also determined with AAS and the method is applied for its determination in steel and environmental samples.     

A method of determining and removing sulphide to allow the determination of sulphate,phosphate, nitrite and ammonia by conventional methods in small volumes of anoxic waters

Mercury(II) chloride is used to precipitate free sulphide from <10-ml samples of anoxic water. The sulphide-free supernatant solution can be used for estimation of sulphide by measuring the concentration of unreacted mercury(II) ion and for determinations of sulphate, inorganic phosphate, ammonia and nitrite by spectrophotometric methods which normally cannot be used because of sulphide interference. Concentrations that can be determined lie within the ranges: sulphide 0.5–180 000 μg S l^?1, sulphate 0.024–2.77 g S l^?1, ammonia 1–70 000 μg N l^?1, nitrite 1–3000 μg N l^?1, inorganic phosphate 1–4000 μg P l^?1. Interstitial waters from estuarine sediments, tidal flats, mangrove swamps, and an anoxic estuarine basin were examined.     

Naphthalene thiourea derivative based colorimetric and fluorescent dual chemosensor for F− and Cu2+/Hg2+ ions

A structurally simple (Z)-2-(naphthalen-2-ylmethylene)-N-phenylhydrazinecarbothioamide (R1) was used as a colorimetric and fluorescent sensor for both F^?  and Cu²⁺/Hg²⁺ ions. R1 selectively recognised F^?  ions as indicated by colour change from colourless to green. Fluorescence spectral data reveal that R1 is an excellent fluorescence chemosensor for Cu²⁺ ions. Finally, R1 was successfully applied to the bioimaging of Cu²⁺ ions in RAW 264.7 macrophage cells.     

Field determination of fluoride in drinking water using a polymeric aluminium complex of 5-(2-carboxyphenylazo)-8-hydroxyquinoline impregnated paper

A simple field method which allows the determination of fluoride in drinking water with a small handheld instrument called Arsenator was developed. Arsenator is a commercially available instrument which was used successfully for reliable determination of arsenic. In the proposed method the functionality of the Arsenator which is based on a photometric measurement of a spot on the reagent paper is expanded to analyse fluoride. A polymeric aluminium complex of 5-(2-carboxyphenylazo)-8-hydroxyquinoline (LH₂) has been prepared as a new specific reagent for fluoride. Job's method of continuous variation was adopted for the determination of the composition of the coloured complex, which was further characterized by UV-VIS spectroscopic studies. The molar absorptivity of the complex formation is 8.48?×?10³?L?mol^?1?cm^?1 at 410?nm. The coloured complex reacts with fluoride on an impregnated paper where its colour changes are dependent on the concentration of fluoride in water samples. The change in the colour was measured using the Arsenator. The method allows a reliable determination of fluoride in the range 0.3 to 2.0?mg?L^?1. Further spectophotometric determinations of fluoride in drinking water were also studied. The determination is based on the reaction of aluminium complex with fluoride in the examined samples. Beer's law is obeyed in the range 0.3 to 2.0?mg?L^?1 of fluoride at 495?nm. Sensitivity, detection limit and quantitation limit of the method were found to be 0.251?±?0.007?µg^?1?mL, 0.1?mg?L^?1 and 0.3?mg?L^?1, respectively. The optimum reaction conditions and other analytical conditions were evaluated. The effect of interfering ions on the determination is described. There is no interference by nitrate or chloride. Sulphate interfered only at high concentrations which are not expected in drinking water.     

Liquid-Liquid Extraction,Photometric and Atomic Absorption Spectrophotometric Determination of Mercury

Abstract

A selective and sensitive spectrophotometric and atomic absorption spectrophotometric method is developed for the determination of traces of mercury with N-phenylcinnamohydroxamic acid (PCHA) in the environment. Mercury is extracted into a chloroform solution of PCHA at pH 8.5-10.0 and determined by AAS. The mercury hydroxamate binary complex is yellow in colour having a maximum absorbance at 390 nm and molar absorptivity 4.3 × 10³ 1 mol^?1 cm^?1, sandell sensitivity 0.0466 μg/cm². The ternary system using 1-(2-pyridylazo)-2-naphthol has molar absorptivity 8.82 × 10³ 1 mol^?1 cm^?1 at 550nm, sandell sensitivity 0.0228 μ/cm². Beer's law is obeyed in the concentration range of 2.37-38.0 ppm and 0.80-19.5 ppm of mercury for binary and ternary system, respectively. The extraction of Hg-PCHA binary system is studied with a liquid cation exchanger, bis-(2-ethyl hexyl) phosphoric acid (HDEHP) and found to have better selectivity than Hg-PCHA-PAN system. The molar absorptivity of the Hg-PCHA-HDEHP system is 8.82 × 10³ 1 mol^?1 cm^?1 at 390 nm and Beer's law is obeyed in the concentration range of 0.47-20 ppm of mercury.

The present method is applied to the determination of mercury in eye drops, aurvedic drugs and environmental samples.