Determination of Vanadium(IV) and Vanadium(V) in Benfield Samples by IEC with Conductivity Detection

In this study, the determination of vanadium valence state, V(IV) and V(V) has been achieved using ion-exchange chromatography with conductivity detector. In this method, V(IV) was determined as V(IV)-EDTA complex and V(V) as vanadate ion. Determination of V(IV) was successfully done using 3 mM carbonate/bicarbonate/EDTA at pH 8.6 as the eluent. The additive, EDTA in the mobile phase did not seem to interfere with the V(IV) analysis. The detection of V(V) was achieved with 5 mM disodium hydrogen phosphate buffer at pH 10.4. A linear calibration graph over VO₃ ^? and V(IV) with concentration ranges 5–15 mg L^?1 gave the detection limit at 0.09 and 0.1 mg L^?1, respectively. Both V(IV) and V(V) were successfully determined in Benfield sample, with concentrations of V(IV) and V(V) at 4 and 11,000 mg L^?1, respectively.     

Cathodic Stripping Voltammetric Determination of Tellurium(IV) with in situ Plated Bismuth-Film Electrode

Abstract

A very sensitive and reliable method is proposed for the determination of tellurium(IV) [Te(IV)] by Osteryoung square-wave cathodic stripping voltammetry. This method is based on the reduction of Te(IV) with bismuth(III) onto an edge-plane pyrolytic graphite electrode, followed by a cathodic potential scan. The reduced Te gave a well-defined catalytic hydrogen wave at ?1200 mV vs. Ag/AgCl. The peak height of the catalytic wave was directly proportional to the initial Te(IV) concentration in the concentration ranges of 0.01–0.10 and 0.1–1.0 µg L^?1 with 30 s deposition time. A 3σ detection limit of 1.0 ng L^?1 Te(IV) was obtained with the same deposition time. The relative standard deviation was 3% on replicate runs (n = 5) for the determination of 0.1 µg L^?1 Te(IV). Analytical results of natural water samples demonstrate that the proposed method is applicable to the determination of traces of Te(IV).     

A Direct Chemiluminescence Method for the Determination of Prulifloxacin Using Tris-(4,7-Diphenyl-1,10-Phenanthrolinedisulfonic Acid) Ruthenium(II)–Cerium(IV) System

Abstract

A simple, rapid, injection chemiluminescence method is described for the determination of prulifloxacin, a commonly used antibiotic. A strong chemiluminescence signal was detected when a mixture of the analyte and tris-(4,7-diphenyl-1,10-phenanthrolinedisulfonic acid)ruthenium(II) was injected into cerium(IV) sulfate. The chemiluminescence signal is proportional to the concentration of prulifloxacin in the range 4.0 × 10^?8–9.0 × 10^?6 mol L^?1. The detection limit is 1.0 × 10^?8 mol L^?1, and the relative standard deviation is 2.2% (n = 11) for the determination of 8.0 × 10^?7 mol L^?1 prulifloxacin. The proposed method was successfully applied to the determination of prulifloxacin in pharmaceutical preparations in capsules, spiked serum, and urine samples.     

Preparation and Application of La(OH)3 Nanoparticles Self‐Assembled Film Modified Electrode

Abstract

La(OH)₃ nanoparticles were successfully prepared with the sol‐gel method, and the preparation of a glassy carbon electrode modified by La(OH)₃ nanoparticles was investigated. The modified electrode shows an excellent electrocatalytic activity for hydroquinone. The anodic and cathodic overpotentials are reduced by ca. 143 mV and 83 mV, respectively, compared with those obtained with a bare glassy carbon electrode. According to the electrochemistry response, we set up a new method to determinate hydroquinone. The catalytic anodic current response of differential pulse voltammogram increases linearly with hydroquinone concentrations from 2.7×10^?7 to 6.5×10^?4 mol L^?1 with a detection limit of 6.0×10^?8 mol L^?1. The recovery of hydroquinone in a simulative sample is satisfactory, especially for its elimination of the interference of 1,2‐benzenediol (pyrocatechol) and 1,3‐benzenediol (m‐dihydroxybenzene). The method is simple, quick, and sensitive.     

Flow-Injection Chemiluminescent Determination of Piroxicam Using Tris (2,2′-bipyridyl) Ruthenium(II)—Potassium Permanganate System

Abstract

A rapid and sensitive chemiluminescence method using flow-injection has been developed for the determination of an analgesic agent drug, piroxicam. The method is based on the chemiluminescence reaction of piroxicam with an acidic potassium permanganate and Ru(bipy)₃ ²⁺. The chemiluminescence intensity is greatly enhanced when quinine sulfate is used as a sensitizer. After optimization of the different experimental parameters, a calibration graph was obtained over a concentration range of 3.0 × 0^?8–3.0 × 0^?5 mol L^?1 with the detection limit of 1.0 × 0^?8 mol L^?1. The relative standard deviation is 1.5% (n = 11) for the determination of 8.0 × 10^?7 mol L^?1 piroxicam. The proposed method was successfully applied to commercial tablets, spiked serum, and urine samples.     

Determination of N-methylcarbamate pesticides using flow injection with photoinduced chemiluminescence detection

A sensitive, economic, rapid and simple method for the determination of four N-methylcarbamate pesticides: methomyl (2.0–80 μg L^?1), aldicarb (5.0–50 μg L^?1), butocarboxim (2.0–60 μg L^?1) and oxamyl (2.0–60 μg L^?1); is reported. It relies on the coupling of photoinduced chemiluminescence (PICL) detection with flow injection (FI) methodology. The automation of FI together with the use of light as a reagent decreased the environmental impact of the analysis. The proposed method was based on the oxidation of these pesticides, previously irradiated on-line with UV light, with cerium(IV), using quinine as a sensitiser. Limits of detection below the legal limits (100 ng L^?1) established by the European Union for drinking waters were obtained without the need of preconcentration steps. A good inter-day reproducibility (1.6–6.4%, n = 5), repeatability (rsd = 2.7 %, n = 25) and high throughput (123 h^?1) were achieved. The method was successfully applied to the determination of methomyl in natural waters with mean recoveries ranging from 90% to 98%.     

Square-Wave Anodic Stripping Voltammetry (SWASV) for the Determination of Ecotoxic Metals,Using a Bismuth-Film Electrode

This article reviews the use of square wave anodic stripping voltammetry for the simultaneous determination of ecotoxic metals (Pb, Cd, Cu, and Zn) on a bismuth-film (BiFE) electrode. The BiFE was prepared in situ on a glassy-carbon electrode (GCE) from the 0.1 mol L^?1 acetate buffer solution (pH 4.5) containing 200 µg L^?1 of bismuth (III). The addition of hydrogen peroxide to the electroanalytical cell proved beneficial for the interference-free determination of Cu (II) together with zinc, lead, and cadmium, using the BiFE. The experimental variables were investigated and optimized with the view to apply this type of voltammetric sensor to real samples containing traces of these metals. The performance characteristics, such as reproducibility, decision limit (CC_a), detection capability (CC_β), sensitivity, and accuracy indicated that the method holds promise for trace Cu²⁺, Pb²⁺, Cd²⁺, and Zn²⁺ levels by employment of Hg-free GCE with SWASV. CCa, and CCβ were calculated according to the Commission Decision of 12 August 2002 (2002/657/EC). Linearity was observed in the range 20–280 µg L^?1 for zinc, 10–100 µg L^?1 for lead, 10–80 µg L^?1 for copper, and 5–50 µg L^?1 for cadmium. Using the optimized conditions, the stripping performance of the BiFE was characterized by low limits of detection (LOD). Finally, the method was successfully applied in real as well as in certified reference water samples.     

A facile one-pot interfacial synthesis of Pt nanoparticles/polypyrrole composites and their application for non-enzymatic sensing hydrogen peroxide

Pt nanoparticles (PtNPs)/polypyrole (PPy) composites were successfully prepared through a facile one-pot interfacial polymerization of pyrrole by using H₂PtCl₆ as the oxidant for the first time. The as-prepared PPy was granular particles with particle size within a few hundred nanometers, on which PtNPs (1.7–3.5) nm were homogeneously dispersed. The PtNPs/PPy composites displayed excellent electrocatalytic activity toward redox of H₂O₂. The non-enzyme sensor constructed with PtNPs/PPy composites displayed good sensing ability toward H₂O₂ at ?0.1 V with a significantly high sensitivity of 6056 μAmM^?1cm^?2 and a low detection limit of 1.8 μM (S/N = 3).     

Molecular Imprinting-Chemiluminescence Sensor for the Determination of Prulifloxacin

Abstract

A selective molecular imprinting-chemiluminescence sensor is developed for the determination of prulifloxacin by using a prulifloxacin-imprinted polymer as recognition material and the cerium(IV)/sodium thiosulfate/prulifloxacin chemiluminescence reaction as the detection system. The linear response range of the sensor is from 8.0 × 10^?8 to 7.0 × 10^?6 mol L^?1 with a detection limit of 2.0 × 10^?8 mol L^?1. The relative standard deviation for 5.0 × 10^?7 mol L^?1prulifloxacin solution is 1.3% (n = 7). This sensor has been applied to the determination of prulifloxacin in urine samples, and the results obtained are satisfactory.     

Electrochemical and Electrocatalytic Properties of Ferrocene Incorporated in L‐Cysteine Self‐Assembled Monolayers on a Gold Electrode

Abstract

The preparation of a gold electrode modified by aminylferrocene (FcAI) covalently bound to L‐cysteine self‐assembled monolayer (L‐Cys/Au SAM) was described, and characterized by cyclic voltammogram (CV) and electrochemical impedance spectroscopy (EIS). In pH 7.4 buffers, FcAI incorporated in L‐Cys/Au SAM gave a pair of well‐defined and quasi‐reversible cyclic voltammetric peaks at 0.109 vs. saturated calomel eletrode (SCE), characteristic of Fe(II)/Fe(III) redox couples of the Fc. The apparent surface electron transfer rate constant is 6.86 s^?1 at the modified electrode. The immobilized Fc gave an excellent electrocatalytic activity for the oxidation of epinephrine (EP). The catalytic current of EP vs. its concentration has a good linear relation in the range of 1.7×10^?7–1.0×10^?4 mol/L, with the correlation coefficient of 0.9975 and detection limit of 1.8×10^?8 mol/L. The modified electrode can be used for the determination of EP in practical injection. The method is simple, quick, sensitive, and accurate.     

A Sensitive Hydrogen Peroxide Sensor Based on Hemoglobin Immobilized on Gold Nanoparticles and 1,6-hexanedithiol Modified Gold Electrode

Hemoglobin (Hb) was successfully immobilized on a gold electrode modified with gold nanoparticles (AuNPs) via a molecule bridge 1,6-hexanedithiol (HDT). The AFM images suggested that the HDT/gold electrode could adsorb more AuNPs. UV-vis spectra indicated that Hb on AuNPs/HDT film retained its near-native secondary structures. The electrochemical behaviors of the sensor were characterized with cyclic voltammetric techniques. The resultant electrode displayed an excellent electrocatalytical response to the reduction of hydrogen peroxide (H₂O₂). The linear relationship existed between the catalytic current and the H₂O₂ concentration ranging from 5.0 × 10^?8 to 1.0 × 10^?6 mol · L^?1. The detection limit (S/N = 3) was 1.0 × 10^?8 mol · L^?1.     

The Determination of Perphenazine by a New Simple Flow‐Injection Chemiluminescence Method

Abstract

A rapid and simple flow‐injection chemiluminescence (CL) method is described for the determination of perphenazine, which is based on the CL intensity that generated from the redox reaction of Ce (IV)-perphenazine in HNO₃ medium is proportional to the perphenazine concentration without any sensitizers. The proposed method allows the determination range within 1.0×10^?7–7.0 ×10^?5 g mL^?1 with a detection limit of 8.0×10^?8 g mL^?1, and it has been successfully applied to the determination of the perphenazine in pharmaceutical tablet compared well with the official method.     

Flow-Batch Method with a Sequential Injection System for Spectrophotometric Determination of Selenium(IV) in Selenium-Enriched Yeast Using o-Phenylenediamine

A precise, accurate, and reliable flow-batch spectrophotometric method for the determination of selenium (IV) was developed using o-phenylenediamine as a reagent with a sequential injection monosegmented flow system incorporating a simple heating unit. The reaction zones of selenium(IV) and o-phenylenediamine were mixed and heated in a chamber at 62°C for 5 minutes. The piaselanol complexes were then detected at a maximum absorption wavelength of 335 nm. In-line single standard calibration and standard addition procedures were developed employing the monosegmented flow technique. Under the optimized conditions, a linear calibration graph in a range of 0.1–4.0 mg L^?1 selenium (IV) was obtained with limits of detection and quantitation of 0.01 and 0.1 mg L^?1, respectively. Relative standard deviations were 2% [for both 0.1 and 0.5 mg L^?1 selenium (IV) (n = 11)]. A sample throughput of 2 h^?1 using four standard addition levels was achieved. The developed system was successfully applied to raw selenium-enriched yeast samples. The analyses performed by the developed method agreed well with those obtained from a standard inductively coupled plasma mass spectrometry method.     

Molecularly imprinted stir bar sorptive extraction coupled with high-performance liquid chromatography for trace analysis of naphthalene sulfonates in seawater

In this paper, a novel molecularly imprinted polymer coated stir bar has been used to selectively extract naphthalene sulfonates (NS_s) directly from seawater sample. 1-Naphthalene sulfonic acid (1-NS) was used as template molecule. The effects of different parameters were optimized on the extraction efficiency and the optimum conditions were established as: the absorption and desorption times were fixed, respectively, at 10 and 15 min, stirring speed was 700 rpm, pH was adjusted to 4.1, amount of NaCl was 1 mol L^?1 and extraction process was performed at a temperature of 50 °C. The linear ranges were 2–250 µg L^?1 for 3,6-NDS-1-OH (1-naphthol-3,6-disulfonic acid), 4–250 µg L^?1 for 2-NS (2-naphthalene sulfonate) and 3–250 µg L^?1 for 1-NS. The detection limits were within the range of 0.32–0.95 µg L^?1. Under optimum conditions, the detection limits of the NSs were 0.84, 0.95 and 0.32 µg L^?1 with the enrichment factor of 117-, 41- and 77-fold for 2-NS, 1-NS, and 6-NDS-1-OH, respectively. The repeatability of the method was satisfactory (0.53 ≤ RSD ≤6.0 %, n = 10). The method has been successfully applied for the analysis of trace amounts of three naphthalene sulfonates in seawater of Chabahar Bay.     

Simultaneous Analysis of Sugars and Polyphenols in Tobacco by CZE with Amperometric Detection Based on a Cu2O/MWCNT-COOH Composite Electrode

A composite electrode was fabricated from Cu₂O powder, carboxyl-functionalized multi-wall carbon nanotubes (MWCNT-COOH), and paraffin oil in the proportions 51:17:32 (w/w). This composite electrode was used for amperometric detection (CZE–AD) in simultaneous capillary zone electrophoretic analysis of chlorogenic acid, rutin, sucrose, glucose, mannose, and fructose in tobacco samples. Under the optimum conditions, the six analytes could be separated in 100 mmol L^?1 NaOH buffer within 30 min. Good linearity was achieved in the range 1 × 10^?7–1 × 10^?4 mol L^?1 for the two polyphenols and 5 × 10^?6–1 × 10^?3 mol L^?1 for the four sugars. The detection limits (S/N = 3) for the polyphenols and sugars were as low as 10^?8 mol L^?1 and 10^?6 mol L^?1, respectively.     

Determination of Low-Molecular-Mass Aldehydes in Water Samples by Liquid Chromatography and Chemiluminescence Detection Using Continuous in situ Derivatization/Preconcentration with Dansylhydrazine

Abstract

A simple, expeditious, and sensitive method has been developed for the determination of low-molecular-mass aldehydes in water samples by liquid chromatography and peroxyoxalate–chemiluminescence detection. The method is based on continuous solid-phase extraction with in situ derivatization/preconcentration of the aldehydes using dansylhydrazine, which was first adsorbed on an RP–C₁₈ mini-column. For 10 mL of aqueous sample, the limits of detection (LOD) for C₁ to C₄ aldehydes were 20–30 ng L^?1, except for formaldehyde, which had an LOD of 400 ng L^?1. Application was illustrated by the determination of these aldehydes in water samples; the interday precision was always less than ca. 7%, and relative recoveries were more than 96%.     

Sensitive Determination of Prulifloxacin by Its Fluorescence Enhancement on Terbium(III)–Sodium Dodecylbenzene Sulfonate System

Abstract

A terbium-sensitized fluorescence spectrophotometry method using an anionic surfactant, sodium dodecyl benzene sulphonate (SDBS), was developed for the determination of prulifloxacin (PUFX). It was found that SDBS significantly enhanced the fluorescence intensity of the PUFX–Tb³⁺ complex (about 13-fold). The optimal experimental conditions were determined as follows: excitation and emission wavelengths of 290 nm and 545 nm, pH 8.0, 4.0 × 10^?5 mol L^?1 terbium(III), and 4.0 × 10^?4 mol L^?1 SDBS. The enhanced fluorescence intensity of the system (ΔF) showed a good linear relationship with the concentration of PUFX over the range 6.0 × 10^?8 to 2.0 × 10^?6mol L^?1 with a correlation coefficient of 0.9991. The detection limit (S/N = 3) was determined as 8.5 × 10^?9 mol L^?1. This method has been successfully applied for the determination of PUFX in pharmaceuticals and human urine/serum samples. Compared with most other methods reported, the rapid and simple procedure proposed here offered higher sensitivity, wider linear range, and good stability. The luminescence mechanism of the system was also discussed in detail. In the fluorescence system of PUFX–Tb³⁺–SDBS, SDBS acted not only as the surfactant but also as the energy donor.     

Static and Hydrodynamic Monitoring of Citalopram Based on its Electro-oxidation Behavior at a Glassy-Carbon Surface

Abstract

The electrooxidative behavior of citalopram (CTL) in aqueous media was studied by cyclic voltammetry (CV) and square-wave voltammetry (SWV) at a glassy-carbon electrode. The electrochemical behaviour of CTL involves two electrons and two protons in the irreversible and diffusion controlled oxidation of the tertiary amine group. The maximum analytical signal was obtained in a phosphate buffer (pH = 8.2). For analytical purposes, an SWV method and a flow-injection analysis (FIA) system with amperometric detection were developed. The optimised SWV method showed a linear range between 1.10 × 10^?5–1.20 × 10^?4 mol L^?1, with a limit of detection (LOD) of 9.5 × 10^?6 mol L^?1. Using the FIA method, a linear range between 2.00 × 10^?6–9.00 × 10^?5 mol L^?1 and an LOD of 1.9 × 10^?6 mol L^?1 were obtained. The validation of both methods revealed good performance characteristics confirming applicability for the quantification of CTL in several pharmaceutical products.     

Automated Determination of Hydrogen Peroxide at the Micro-Molar Level in Rainwater and Snow Using a Stopped-Flow Approach in a Hybrid Sequential Injection/Flow Injection Manifold

A new automated method is reported for the determination of H₂O₂ in real samples. The method is based on the quenching effect of the analyte on the reaction between tris(2-carboxyethyl)phosphine (TCEP) and Ellman's reagent (DTNB). All necessary steps were accomplished under flow conditions using a hybrid sequential injection (SI)/flow injection (FI) setup. The sensitivity was enhanced by applying a stopped-flow step (120 s) in order to promote the reaction between H₂O₂ and TCEP. The proposed analytical protocol was validated for linearity (10–75 µmol L^?1), limits of detection (c _L = 1.0 µmol L^?1), quantitation (c _Q = 3.3 µmol L^?1), precision (s _r = 1.3–1.7%), accuracy, and selectivity. It was then applied successfully to the analysis of H₂O₂ in spiked rainwater and snow samples.     

Determination of neptunium in a reprocessing plant by an on-line solid-phase extraction/electrochemical detection system

In this study, a flow-based electrochemical detection system coupled to a solid-phase extraction column was developed for the determination of neptunium in the presence of Pu(IV). Np(V) in the sample solution was completely oxidized to Np(VI) via electrolysis using a column electrode composed of carbon fibers. The column electrode effluent was then loaded onto a TEVA^® column, and subsequently onto a UTEVA^® column using 3 mol L^?1 HNO₃. Pu(IV) was retained on the TEVA column and separated from Np(VI), while Np(VI) was retained on the UTEVA column. Np(VI) was eluted from the UTEVA column with 0.01 mol L^?1 HNO₃ and then introduced directly into a flow-through electrolysis cell. An electrochemical amperometric method with a working potential of +0.1 V (vs. Ag/AgCl) was used to detect Np(VI). The current produced due to the reduction of Np(VI) was continuously monitored and recorded, and the Np concentration was calculated from the peak area. The relative standard deviation of 10 analyses was 2.4 % for an Np solution (0.50 mg L^?1) containing 1.0 μg Np. The detection limit, which was determined to be three times the standard deviation, was 35 μg L^?1 (70 ng Np).