锑电极电位溶出法测定锌、镉、铅

提出了采用锑电极作为工作电极同时测定痕量重金属锌、镉、铅的电位溶出法。探讨了同时测定锌、镉、铅的最佳条件。在pH=5.0的HAc-NaAc缓冲溶液中,Zn2+、Cd2+、Pb2+分别在-1.07、-0.70、-0.52 V得到灵敏的电位溶出峰。沉积时间为60 s时,锌、镉、铅的质量浓度分别在0~16.0、0~1.6、0~0.08 μg/mL范围内,与各自微分电位溶出峰高呈线性关系,检出限分别为4.0、0.3、0.03 μg/L。测定了水样中痕量锌、镉、铅的含量,结果令人满意。     

平台石墨炉原子吸收法直接测定镍基合金中铅和锑

平台石墨炉原子吸收法直接测定镍基合金中铅和锑谢文兵，姚金玉，胡庆兰（中国科学院长春应用化学研究所长春１３００２２）关键词石墨炉原子吸收，镍合金，铅，锑，基体改进剂石墨炉原子吸收法是测定痕量元素最有效的方法之一。但是铅和锑都是易挥发元素，为了增强灰化过...     

空气 - 乙炔火焰原子吸收法连续测定铜粉中微量Fe、Pb、Sb、Zn和Ni

用HNO3-HCl溶解试样,在几个相同量的试液中,分别加入质量浓度依次递增的5种元素的标准溶液,用火焰原子吸收法连续测定了Fe、Pb、Sb、Zn和Ni的含量,建立了优化的仪器测定条件,并对可能存在的元素进行了干扰试验。结果表明,Fe、Pb、Sb等5种元素的回收率为98.0%～102.3%,相对标准偏差为1.4%～2.5%。     

Speciation Analysis of Antimony (III) and Antimony (V) by Flame Atomic Absorption Spectrometry After Separation/Preconcentration With Cloud Point Extraction

A sensitive and simple method for flame atomic absorption spectrometry (FAAS) determination of antimony species after separation/preconcentration by cloud point extraction (CPE) has been developed. When the system temperature is higher than the cloud point extraction temperature, the complex of antimony (III) with N-benzoyl-N-phenyhydroxylamine (BPHA) can enter the surfactant-rich phase, whereas the antimony (V) remains in the aqueous phase. Antimony (III) in surfactant-rich phase was analyzed by FAAS and antimony (V) was calculated by subtracting of antimony (III) from the total antimony after reducing antimony (V) to antimony (III) by L-cysteine. The main factors affecting the cloud point extraction, such as pH, concentration of BPHA and Triton X-114, equilibration temperature and time, were investigated systematically. Under optimized conditions, the detection limits (3σ) were 1.82 ng mL⁻¹ for Sb(III) and 2.08 ng mL⁻¹ for Sb(total), and the relative standard deviations (RSDs) were 2.6% for Sb(III) and 2.2% for Sb(total). The proposed method was applied to the speciation of antimony species in artificial seawater and wastewater, and recoveries in the range of 95.3–106% were obtained by spiking real samples. This technique was validated by means of reference water materials and gave good agreement with certified values.     

Volatile phase introduction of metallic beta-diketonates in atomic absorption spectrometry: Zinc acetylacetonate

The combined method volatile phase-atomic spectroscopy is an improvement in comparison with the conventional method of liquid sample introduction. The generation of a volatile phase by sublimation from an ethanolic solution of zinc acetylacetonate monohydrate and the obtainment of an analytical signal by AAS is proposed in this paper. The volatile phase is introduced in a silica tube by means of a nitrogen stream as carrier gas. The proposed method gives an improved sensitivity of 6.2 times with respect to the introduction of the same sample in liquid phase and more than 30 times with respect to the introduction of the zinc as chloride in aqueous solution.     

Determination of Lead in Coal Using Direct Solid Sampling and High-Resolution Continuum Source Graphite Furnace Atomic Absorption Spectrometry

A method has been developed for the determination of Pb in coal using direct solid sampling (SS) and high-resolution continuum source graphite furnace atomic absorption spectrometry (HR-CS GF AAS). The certified coal reference materials used in this study were ground in an agate mortar to particle size ≤50 μm. Mass aliquots between 0.1 and 1 mg were weighed onto pyrolytic graphite platforms, and inserted directly into the graphite tube. For pyrolysis temperatures lower than 600 °C, a continuous background due to radiation scattering at solid particles preceded the atomic signal, as the coal matrix could not be sufficiently eliminated under these conditions. An optimized pyrolysis temperature of 700 °C was adopted for Pb without the use of a modifier. The optimum atomization temperature was found to be 1700 °C. Under these conditions, interference-free determination could be performed with calibration against aqueous standards in 0.5% v/v HNO₃. A total of six certified reference coal samples were analyzed, and the results obtained were all in good agreement with certified and informed values, respectively, according to a Student t-test at a 95% confidence level. A detection limit of 0.008 μg g⁻¹ for Pb was obtained at the 217.000 nm resonance line, a value comparable to those obtained by other sensitive, but much more sophisticated techniques, showing that the absence of dilution in the SS-HR-CS GF AAS method allows at least equivalent detection performance.     

Differential Pulse Polarographic Determination of Gallium and Niobium in Samples After Preconcentration of Their Quinolin-8-Olate Complexes on Microcrystalline Naphthalene

Abstract

Gallium and niobium react with quinolin-8-ol to form water insoluble complexes which are quantitatively adsorbed on microcrystalline naphthalene from the large volume of their aqueous solutions in the pH range of 3.5 - 8.2 and 6.2 - 9.4, respectively. After filtration, the metal complexes were desorbed with 10 ml of HCl (1M for Ga and 11 M for Nb) and determined by using a differential pulse polarograph (DPP). The dissolved oxygen is removed by adding a few milliliters of 4% NaBH₄ solution in the case of gallium. The detection limits are 0.04 ppm for gallium and 0.05 ppm for niobium at the minimum instrumental settings (signal to noise ratio = 2). The linearities are maintained in the concentration range 0.1 - 5.0 ppm for gallium and 0.4 - 6.0 ppm for niobium with correlation factors of 0.9997 and 0.9996 and relative standard deviations of 0.81 and 0.95%, respectively.

Characterization of the electroactive process included an examination of the degree of reversibility. Various parameters such as the effect of pH volume of aqueous phase, reagent and naphthalene concentrations and the interference of a large number of anions and cations on the estimation of these elements were studied in detail. The method is found to be highly selective, fairly sensitive, rapid, simple and economical. It has been applied for the trace determination of gallium and niobium in various standard alloys and may be applied safely for the analyses of complex materials like environmental samples and ores.

     

Preconcentration and Determination of Trace Palladium with 1, 5-Diphenylcarbazone- Naphthalene as Adsorbent by Atomic Absorption Spectrometry

ABSTRACT|A highly selective, sensitive, rapid and simple atomic absorption spectrometric method has been developed for the determination of trace amounts of palladium in synthetic and real samples. Palladium can be adsorbed on naphthalene-1, 5-diphenyl-carbazone (DPCO) as adsorbent from the large volume of its aqueous solutions in the pH range 2.0 to 0. After filtration, the metal ion was desorbed with 5ml of 0.25M thiourea solution, and determined by AAS.

Alternatively, palladium can be adsorbed on this adsorbent packed in a column and determined similarly. The detection limit is 0.5 μg (signal to noise ratio=2) and the linearity is maintained in concentration range of 1.5-50μg of Pd with a correlation coefficient of 0.9992. Seven replicate determinations on samples containing 2.5 and 20μg of palladium gave the relative standard deviations of 3.6% and 0.81%, respectively. Various parameters such as effect of pH, volume of aqueous phase, shaking time and interference of number of ions on the determination of Pd have been studied in detail to optimize the conditions for its estimation in various synthetic and real samples.     

火焰原子吸收光谱法测定铜原尾矿中的铅

铜原尾矿中硅含量较高,针对这一特性,提出了试样采用饱和氟化氢铵、盐酸、硝酸溶解,在硝酸(5%)介质中,于原子吸收光谱仪上,使用空气-乙炔火焰进行铅的测定,建立了铜原尾矿中铅的测定方法。研究结果表明铅的质量浓度在0.5~3μg/mL范围内与吸光度A有良好的线性关系,方法的相对标准偏差0.92%~2.4%,加标回收率96.0%~106.0%,方法以3倍的空白溶液11次测定值的标准偏差作为检出限,检出限为0.08μg/mL,方法准确、可靠。     

Determination of cadmium and lead in aqueous environmental samples after complexation and microextraction onto the surface of an empty solvent-impregnated polypropylene fibre coupled with electrothermal AAS

A procedure based on polypropylene hollow-fibre preconcentration coupled with electrothermal atomic absorption spectrometry (ETAAS) was developed for the determination of cadmium and lead in seawater, wastewater, tap water and lake water samples. The n-octanol was immobilised in the pores of the polypropylene hollow fibre, which was used as the liquid sorption membrane negating the need for acceptor liquid phase in the lumen. The metal ions were extracted from water samples onto the impregnated fibre, as ammonium pyrrolydine dithiocarbamate (APDC) complexes, and then back-extracted into a small volume of 0.1?mol?L^?1 HNO₃. The main extraction-related parameters were properly evaluated and an interference study was carried out. Linear regression lines were plotted and replicate analyses of real samples revealed that the proposed method is precise and accurate, able to be applied in routine analysis with detection limits of 4?ng?L^?1 and 12?ng?L^?1 for Cd and Pb, respectively.     

Matrix Digestion of Soil and Sediment Samples for Extraction of Lead,Cadmium and Antimony and Their Direct Determination by Inductively Coupled Plasma-Mass Spectrometry and Atomic Emission Spectrometry

An environmentally friendly and simple method has been developed for complete digestion of lead, cadmium and antimony from soil samples using a magnesium nitrate assisted dry ashing procedure. Statistical data for a series of experiments with standard reference materials are presented, and precision values are found to be comparable for inductively coupled plasma-mass spectrometry and for inductively coupled plasma-atomic emission spectrometry. From a single digest solution all analytes are quantified without involving any pre-concentration routes. Inter-method comparison of inductively coupled plasma-mass spectrometry (ICP-MS) and inductively coupled plasma-atomic emission spectrometry (ICP-AES) shows that the probability of the results being different is less than 99%.     

电感耦合等离子体原子发射光谱(ICP-AES)法测定硫化物矿石中的铜铅锌

建立了电感耦合等离子体原子发射光谱(ICP-AES)法同时测定硫化物矿石中Cu、Pb、Zn三种元素的方法,取代了传统的四酸(HCl+HNO3+HClO4+HF)溶样法,采用简单的盐酸和硝酸溶解矿石,大大缩短了分析时间。选择干扰少且灵敏度高的谱线作为待测元素的分析谱线,采用左右两点扣背景的方法校正光谱干扰和基体匹配方法消除物理干扰,用GBW07162和GBW07163等不同种类的国家一级标准物质进行精密度和准确度实验,测定结果的相对标准偏差都在10%以内,测定结果都在标准值的误差范围内,符合地质矿产开发的要求。     

Analysis of Zinc in <Emphasis Type="Italic">Vitix Negundo</Emphasis> Foliage by AAS and Application of a New Kind of Standard Addition Method

Flame atomic absorption spectrometry was used to determine zinc in Vitix negundo found in Guangxi Province, P.R. China, and a novel standard addition method was used. The difference between the traditional standard addition method and the novel standard addition method is that the total concentration (i.e. the sum of the sample and analyte) is measured and plotted against the added analyte in the novel standard addition method. The zinc contents of Vitix negundo foliage found in Nongla, Mashan City and at the Yaji Karst experiment site, Guilin City, Guangxi Province, P.R. China, are 138.0±2.4 and 103.0±2.4µg g^–1 respectively. The method proved to exhibit satisfactory precision and accuracy.     

A multicommuted flow system for the determination of copper, chromium, iron and lead in lubricating oils with detection by flame AAS

In this work, a flow analysis procedure for the determination of copper, chromium, iron and lead in lubricating oils using flame AAS as detection technique is described. The flow manifold was designed to implement the multicommutation approach and it comprised three 3-way solenoid valves controlled by a personal computer. The flow system presented allowed to process the oil samples to determine wear metals without any prior preparation. Aiming to assess accuracy the results were compared with those obtained by manual procedure using flame AAS. Applying the joint-confidence ellipse test, no significant difference at the 95% confidence level was observed. Other profitable features such as a sample throughput of 50 determinations per hour; relative standard deviations (n = 5) below 2% for Cu, and below 8% for Cr, Fe and Pb; and linear responses in the range 0–40 ppm (w/w) (Cu, Fe) and 0–15 ppm (w/w) (Cr, Pb) were also achieved.     

用DDTC-Zn作载体流动注射在线共沉淀预富集火焰原子吸收法测定人发和水样中的痕量铅

提出了在高酸度下流动注射在线共沉淀预富集－火焰原子吸收法测定痕量铅的新体系。在０．５ｍｏｌ／ＬＨＣｌ介质中痕量铅与ＤＤＴＣ－Ｚｎ螯合物产生共沉淀。在线生成的沉淀物收集在编结反应器中，用甲基异丁酮溶解沉淀并直接引入火焰原子化器中进行测定。经４０ｓ富集，检测限为２．７μｇ／Ｌ。测定含量为２００μｇ／Ｌ的铅时，相对标准偏差为１．３％。建立的方法已成功地应用于人发标准参考物中和水样中痕量铅的测定     

Determination of Lead,Cadmium and Mercury in Surface Marine Sediments and Mussels

Abstract

Lead, cadmium and mercury were determined in sediments and mussels, and the ability of these indicators to record metal variations in coastal marine environment is described in this work. The results of an extended investigation of the status of three gulfs at Northern Greece are given, regarding the content of these metals in surface sediments and Mytilus galloprovincialis. The samples were collected during a four-year period. The total concentration of the above heavy metals was determined after digestion of the samples by suitable mixtures of acids, including nitric, perchloric and hydrofluoric acid. The digestion was carried out in a steel pressurised bomb with closed teflon vessels. Lead and cadmium were determined by means of electrothermal atomic absorption spectrometry (ETAAS), and mercury by cold vapour atomic absorption spectrometry (CVAAS). The results were statistically evaluated by analysis of variance, and emphasis was given to annual, seasonal and spatial sources of variation. The annual changes during the last four years and the spatial distribution of heavy metals load is also discussed.     

X射线荧光光谱法快速测定黑铜中的铜、砷、锑、铋、铅、镍、锌和锡

建立X射线荧光光谱法快速测定黑铜中的铜,砷,锑,铋,铅,镍,锌和锡等多种元素含量的方法。采用自制的黑铜样品作为标准样品建立标准工作曲线。实验确定了样品加工时最佳的铣样速度及谱线重叠干扰的校正方法,并用理论影响系数校正基体干扰。试验结果表明,各元素的工作曲线线性关系较好,线性相关系数均大于0.996。各元素的检出限在17~47μg/g之间。测定结果的相对标准偏差为0.038%~2.73%(n=7)。两个样品的测定结果与标准分析方法的测定结果相符。该方法具有较好的准确度和精密度,分析速度快,能满足炉前快速分析的需要。     

火焰原子吸收法测定植物叶片中Pb、Cd、Cu、Zn含量

对八种植物叶片 (糖胶树、榕树、红花羊蹄甲、银合欢、垂叶榕、白玉兰、蟛蜞菊、大花紫薇 )中Pb、Cd、Cu、Zn的测定方法进行了研究 ,采用炭化—灰化—硝酸溶解方法进行样品处理 ,火焰原子吸收法测定Pb、Cd、Cu、Zn四种重金属元素。结果表明 ,该法准确 ,回收率高。各元素的回收率分别为 :铅 88%～ 1 0 5 %、镉 90 %～ 1 0 3 %、铜 90 %～ 1 0 5 %、锌 91 %～ 1 0 5 %。     

Development of an automated sequential injection on-line solvent extraction-back extraction procedure as demonstrated for the determination of cadmium with detection by electrothermal atomic absorption spectrometry

An automated sequential injection (SI) on-line solvent extraction-back extraction separation/preconcentration procedure is described. Demonstrated for the assay of cadmium by electrothermal atomic absorption spectrometry (ETAAS), the analyte is initially complexed with ammonium pyrrolidinedithiocarbamate (APDC) in citrate buffer and the chelate is extracted into isobutyl methyl ketone (IBMK), which is separated from the aqueous phase by means of a newly designed dual-conical gravitational phase separator. A metered amount of the organic eluate is aspirated and stored in the PTFE holding coil (HC) of the SI-system. Afterwards, it is dispensed and mixed with an aqueous back extractant of dilute nitric acid containing Hg(II) ions as stripping agent, thereby facilitating a rapid metal-exchange reaction with the APDC ligand and transfer of the Cd into the aqueous phase. The aqueous phase is separated in a second dual-conical gravitational phase separator, and 30 μl of it is entrapped and metered in a sample loop (SL) and subsequently introduced via air segmentation into the graphite tube for analyte quantification. The ETAAS determination is performed in parallel with the separation/preconcentration process of the ensuing sample. An enrichment factor of 21.4, a detection limit of 2.7 ng l⁻¹, along with a sampling frequency of 13 h⁻¹ were obtained at a sample flow rate of 6.0 ml min⁻¹. The precision (R.S.D.) at the 0.4 μg l⁻¹ level was 1.8% as compared to 3.2% when quantifying the organic extractant directly. The applicability of the procedure is demonstrated for the determination of trace levels of cadmium in three certified reference materials.