A novel method of liquid chromatography–tandem mass spectrometry combined with chemical derivatization for the determination of ribonucleosides in urine

Ribonucleosides are the end products of RNA metabolism. These metabolites, especially the modified ribonucleosides, have been extensively evaluated as cancer-related biomarkers. However, the determination of urinary ribonucleosides is still a challenge due to their low abundance, high polarity and serious matrix interferences in urine samples. In this study, a derivatization method based on a chemical reaction between ribonucleosides and acetone to form acetonides was developed for the determination of urinary ribonucleosides. The derivative products, acetonides, were detected by using liquid chromatography–tandem mass spectrometry (LC–MS/MS). The methodological evaluation was performed by quantifying four nucleosides for linear range, average recovery, precision, accuracy and stability. The validated procedures were applied to screen modified ribonucleosides in urine samples. Improvement of separation and enhancement of sensitivity were obtained in the analysis. To identify ribonucleosides, inexpensive isotope labeling acetone (acetone-d₆) and label-free acetone were applied to form ordinary and deuterated acetonides, respectively. The two groups of samples were separated with orthogonal partial least squares (OPLS). The ordinary and deuterated pairs of acetonides were symmetrically distributed in the S-plot for easy and visual signal identification. After structural confirmation, a total of 56 ribonucleosides were detected, 52 of which were modified ribonucleosides. The application of derivatization, deuterium-labeling and multivariate statistical analysis offers a new option for selective detection of ribonucleosides in biological samples.     

Ultra-high-pressure liquid chromatography–tandem mass spectrometry method for the determination of alkylphenols in soil

A novel method has been developed for the determination of alkylphenols in soil by ultra-high-pressure liquid chromatography employing small particle sizes, combined with tandem mass spectrometry. Soil samples were extracted with pressurized liquid extraction (PLE) and then cleaned with solid-phase extraction (SPE). The extracts were separated on C18 column (1.7 μm, 50 mm × 2.1 mm) with a gradient elution and a mobile phase consisting of water and acetonitrile, and then detected by an electrospray ionization tandem mass spectrometry in negative ion mode with multiple reaction monitoring (MRM). Compared with traditional liquid chromatography, it took ultra-high-pressure liquid chromatography much less time to analyze alkylphenols. Additionally, the ultra-high-pressure liquid chromatography/tandem mass spectrometry method produces satisfactory reliability, sensitivity, and accuracy. The average recoveries of the three target analytes were 74.0–103.4%, with the RSD < 15%. The calibration curves for alkylphenols were linear within the range of 0.01–0.4 μg/ml, with the correlation coefficients greater than 0.99. When 10 g soil sample was used for analysis, the limits of quantification (LOQs) of the three alkylphenols were all 1.0 μg/kg.     

Dispersive liquid–liquid–liquid microextraction combined with liquid chromatography for the determination of chlorophenoxy acid herbicides in aqueous samples

A novel sample preparation method “Dispersive liquid–liquid–liquid microextraction” (DLLLME) was developed in this study. DLLLME was combined with liquid chromatography system to determine chlorophenoxy acid herbicide in aqueous samples. DLLLME is a rapid and environmentally friendly sample pretreatment method. In this study, 25 μL of 1,1,2,2-tetrachloroethane was added to the sample solution and the targeted analytes were extracted from the donor phase by manually shaking for 90 s. The organic phase was separated from the donor phase by centrifugation and was transferred into an insert. Acceptor phase was added to this insert. The analytes were then back-extracted into the acceptor phase by mixing the organic and acceptor phases by pumping those two solutions with a syringe plunger. After centrifugation, the organic phase was settled and removed with a microsyringe. The acceptor phase was injected into the UPLC system by auto sampler. Fine droplets were formed by shaking and pumping with the syringe plunger in DLLLME. The large interfacial area provided good extraction efficiency and shortened the extraction time needed. Conventional LLLME requires an extraction time of 40–60 min; an extraction time of approximately 2 min is sufficient with DLLLME. The DLLLME technique shows good linearity (r² ≥ 0.999), good repeatability (RSD: 4.0–12.2% for tap water; 5.7–8.5% for river water) and high sensitivity (LODs: 0.10–0.60 μg/L for tap water; 0.11–0.95 μg/L for river water).     

Dispersive liquid–liquid microextraction based on ionic liquid in combination with high-performance liquid chromatography for the determination of bisphenol A in water

A method termed dispersive liquid–liquid microextraction (DLLME) coupled with high-performance liquid chromatography-variable wavelength detection (HPLC-VWD) was developed. DLLME-HPLC-VWD is a method for determination of bisphenol A (BPA) in water samples. In this microextraction method, several parameters such as extraction solvent volume, sample volume, disperser solvent, ionic strength, pH, and disperser volume were optimised with the aid of interactive orthogonal array and a mixed level experiment design. First, an orthogonal array design was used to screen the significant variables for the optimisation. Second, the significant factors were optimised by using a mixed level experiment. Under the optimised extraction conditions (extraction solvent: ionic liquid [C₆MIM][PF₆], 60 µL; dispersive solvent: methanol, 0.4 mL; and pH = 4.0), the performance of the established method was evaluated. The response linearity of the method was observed in a range of 0.002–1.0 mg L^?1 (three orders of magnitude) with correlation coefficient (R ²) of 0.9999. The repeatability of this method was 4.2–5.3% for three different BPA levels and the enrichment factors were above 180. The extraction recovery was about 50% for the three different concentrations with 3.4–6.4% of RSD. Limit of detection of the method was 0.40 µg L^?1 at a signal-to-noise ratio of 3. In addition, the relative recovery of sample of Songhua River, tap water and barrel-drain water at different spiked concentration levels was ranged 95.8–103.0%, 92.6–98.6% and 87.2–95.3%, respectively. Compared with other extraction technologies, there have been the following advantages of quick, easy operation, and time-saving for the present method.     

Development of a dispersive liquid–liquid microextraction method for the determination of fluoroquinolones in chicken liver by high performance liquid chromatography

A simple and cost effective sample pre-treatment method, dispersive liquid–liquid microextraction (DLLME), has been developed for the extraction of six fluoroquinolones (FQs) from chicken liver samples. Clean DLLME extracts were analyzed for fluoroquinolones using liquid chromatography with diode array detection (LC-DAD). Parameters such as type and volume of disperser solvent, type and volume of extraction solvent, concentration and composition of phosphoric acid in the disperser solvent and pH were optimized. Linearity in the concentration range of 30–500 μg kg⁻¹ was obtained with regression coefficients ranging from 0.9945 to 0.9974. Intra-day repeatability expressed as % RSD was between 4 and 7%. The recoveries determined in spiked blank chicken livers at three concentration levels (i.e. 50, 100 and 300 μg kg⁻¹) ranged from 83 to 102%. LODs were between 5 and 19 μg kg⁻¹ while LOQs ranged between 23 and 62 μg kg⁻¹. All of the eight chicken liver samples obtained from the local supermarkets were found to contain at least one type of fluoroquinolone with enrofloxacin being the most commonly detected. Only one sample had four fluoroquinolone antibiotics (ciprofloxacin, difloxacin, enrofloxacin, norfloxacin). Norfloxacin which is unlicensed for use in South Africa was also detected in three of the eight chicken liver samples analyzed. The concentration levels of all FQs antibiotics in eight samples ranged from 8.8 to 35.3 μg kg⁻¹, values which are lower than the South African stipulated maximum residue limits (MRL).     

A simple hollow fiber renewal liquid membrane extraction method for analysis of sulfonamides in honey samples with determination by liquid chromatography–tandem mass spectrometry

A sensitive and precise analysis using hollow fiber renewal liquid membrane (HFRLM) extraction followed by high performance liquid chromatography–tandem mass spectrometry (LC–MS/MS) is described for determination of five sulfonamides in honey samples. In this procedure, the organic solvent introduced directly into the sample matrix extracts the sulfonamides and carries them over the polypropylene porous membrane. An organic solvent is immobilized inside the polypropylene porous membrane, leading to a homogeneous phase. The stripping phase at higher pH in the lumen of the membrane promotes the ionization of the target compounds releasing them to this phase. The most important parameters affecting the extraction efficiency were optimized by multivariable designs (pH and sample mass, pH and buffer for stripping phase, extraction temperature and time, type and volume of extractor solvent and use of salt to saturate the sample). Detection limits in the range of 5.1–27.4 μg kg⁻¹ and linearity coefficient of correlation higher than 0.987 were obtained for the target analytes. The results obtained for the proposed method show that HFRLM–LC–MS/MS can be used for determination of the five sulfonamides studied in honey samples with excellent precision, accuracy, practicality and short analysis time.     

Sensitive liquid chromatography–tandem mass spectrometry method for the determination of pantoprazole sodium in human urine

A sensitive and selective liquid chromatographic–tandem mass spectrometric (LC–MS–MS) method was developed to determine pantoprazole sodium (PNT) in human urine. After solid-phase extraction with SPE cartridge, the urine sample was analysed on a C₁₈ column (symmetry 3.5 μm; 75 mm × 4.6 mm i.d) interfaced with a triple quadrupole tandem mass spectrometer. Positive electrospray ionization was employed as the ionization source. The mobile phase consisted of acetonitrile–water (90:10, v/v). The method was linear over a concentration range of 1–100 ng mL^?1. The lower limit of quantitation was 1 ng mL^?1. The intra-day and inter-day relative standard deviation across three validation runs over the entire concentration range was <10.5%. The accuracy determined at three concentrations (8.0, 50.0 and 85.0 ng mL^?1 PNT) was within ±1.25% in terms of relative errors.     

Coupling of air-assisted liquid–liquid microextraction method with partial least squares for simultaneous spectrophotometric determination of some preservatives

An air-assisted liquid–liquid microextraction method coupled with a multivariate calibration method, namely partial least squares (PLS), was developed for the extraction and simultaneous determination of benzoic acid (BA) and sorbic acid (SA) via a spectrophotometric approach. In this work, a two-step microextraction method was used. In the first step, analytes were extracted from acidic aqueous solution into octanol, as an organic solvent, and in the second step, the analytes were simultaneously back-extracted into an alkaline aqueous solution. The high absorption signal of octanol was the main reason to perform this back-extraction step. The effects of different parameters on the method efficiency were investigated; the parameters included extraction solvent volume, ionic strength of aqueous solution, pH, number of extraction cycles, and aqueous sample volume. Under optimum conditions, calibration graphs were seen to be linear over the range of 0.1–2.0 µg mL^?1 for the both analytes. Other analytical parameters were obtained as follows: Enrichment factors (EFs) were found to be 14.98 and 13.03, and limits of detection were determined to be 0.03 and 0.04 µg mL^?1 for BA and SA, respectively. As the last step, binary mixtures of the analytes were prepared and simultaneously extracted using the proposed method. Finally, PLS modeling was used for multivariate calibration of spectrophotometric data. It was successfully utilized for the analysis of the target analytes in real samples.     

A liquid chromatography–atmospheric pressure photoionization tandem mass spectrometric method for the determination of azaarenes in atmospheric particulate matter

The development, optimization and validation of a liquid chromatography–atmospheric pressure photoionization tandem mass spectrometric (LC–APPI/MS/MS) method for the determination of 15 azaarenes (4-azafluorene, benzo[h] and -[f]quinoline, phenanthridine, acridine, 1-azafluoranthene, 4-azapyrene, benz[a]- and -[c]acridine, -10-azabenzo[a]pyrene, 7,9- and 7,10-dimethylbenz[c]acridine, dibenz[a,j]-, -[c,h] and [a,i]acridine) in airborne particulate matter is described. Each compound was detected and quantified operating in multiple reaction monitoring mode. Extraction of azaarenes was achieved using accelerated solvent extraction (ASE) with dichlormethane/methanol (50/50, v/v). After extraction, no additional clean-up procedure like solid phase or liquid/liquid extraction was necessary. Limits of quantification (S/N × 10) ranged from 0.2 pg/μl to 1.4 pg/μl, matrix dependent recoveries were between 57% and 94%, with relative standard deviations from 8% to 17%. Applicability of the method was demonstrated analyzing 10 samples of particulate matter (PM_2.5) collected in winter 2008. In all samples dimethylbenz[c]acridines as well as dibenzacridines were below the limit of quantification, concentration of the remaining analytes were in the range from 0.002 ng/m³ to 0.356 ng/m³.     

A confirmatory method for the determination of phenolic endocrine disruptors in honey using restricted-access material–liquid chromatography–tandem mass spectrometry

The present work describes the development and validation of an analytical method based on liquid chromatography (LC), coupled with tandem mass spectrometry (MS/MS) that allows the determination and confirmation of several endocrine-disrupting chemicals (EDCs) in honey. The EDCs studied were nine phenols of different nature: chlorophenols (2,4-dichlorophenol, 2,4,5-trichlorophenol, and pentachlorophenol), alkylphenols (4-tert-butylphenol, 4-tert-octylphenol, and 4-n-octylphenol) bisphenols (bisphenol-A and bisphenol-F), and 4-tert-butylbenzoic acid. The method incorporates a restricted-access material (RAM), coupled on-line to the LC-MS/MS system, which allows direct injection of the matrix into the RAM-LC-MS/MS system. The optimized method developed, RAM-LC-MS/MS, was applied to fortified honey samples, affording detection limits in the 0.6–7.2 ng g⁻¹ range, calculated for a signal-to-noise ratio of 3. In addition, the method was validated as a quantitative confirmatory method according to European Union Decision 2002/657/EC. The validation criteria evaluated were linearity, repeatability, reproducibility, recovery, decision limits, detection capabilities, specificity, and ruggedness. Repeatability and within-laboratory reproducibility were evaluated at two concentration levels, being ±11% or below at 20 ng g⁻¹. The decision limits (CC_α) and detection capabilities (CC_β) were in the 1.7–12.6 and 2.8–21.6 ng g⁻¹ range, respectively.     

Development of a new ultra-high-performance liquid chromatography–tandem mass spectrometry method for the determination of digoxin and digitoxin in plasma: Comparison with a clinical immunoassay

Cardiac glycosides digoxin and digitoxin are used in therapy for the treatment of congestive heart failure. Moreover, these compounds can be responsible for intoxication cases caused by fortuitous ingestion of leaves of Digitalis. Due to the narrow therapeutic range of these drugs, therapeutic drug monitoring is recommended in the clinical practice. In this context, immunoassays-based methods are generally employed but digoxin- and digitoxin-like compounds can interfere with the analysis. The aim of this study was to develop and validate an original UPLC–MS/MS method for the determination of digoxin and digitoxin in plasma. The method shows adequate sensitivity and selectivity with acceptable matrix effects and very good linearity, accuracy, precision, and recovery. A simple liquid–liquid extraction procedure was used for sample clean-up. The method was applied for the analysis of n = 220 plasma samples collected in two different clinical chemistry laboratories and previously tested by the same immunoassay. The statistical comparison showed a relevant negative bias of the UPLC–MS/MS method versus the immunoassay. These results are consistent with an immunoassay overestimation of digoxin plasmatic levels due to cross-reaction events with endogenous digoxin-like substances.     

Sensitive determination of nitrophenol isomers by reverse-phase high-performance liquid chromatography in conjunction with liquid–liquid extraction

A method for the highly sensitive determination of 2-, 3- and 4-nitrophenols was developed using reverse-phase high-performance liquid chromatography (RP-HPLC) with a UV photodiode array detector. Using a reverse-phase column and 40% aqueous acetonitrile as an eluent (i.e. isocratic elution), the integrated peak area of detector output was linear up to 300 mg/L and the detection limit was 150 µg/L. The sensitivity of this detection method was improved by pretreating the sample solutions with a solvent extraction procedure that makes use of the high partition coefficient of ethyl acetate (EA)/water system. To find an optimum condition for the extraction procedure, this process was simulated by plotting the concentration of nitrophenol extracted in organic solvent against the volume multiplication factor at various partition coefficient of solute. This simulation demonstrated that EA is a superior extractant to other organic solvents. With the newly developed method, the detection limit was extended to 0.3 µg/L. This method offers fast, reliable and more sensitive determination of nitrophenol isomers than any other HPLC method.     

Rapid and sensitive method for the determination of acetaldehyde in fuel ethanol by high-performance liquid chromatography with UV–Vis detection

A high-performance liquid chromatography (HPLC) method for the determination of acetaldehyde in fuel ethanol was developed. Acetaldehyde was derivatized with 0.900 mL 2,4-dinitrophenylhydrazine (DNPHi) reagent and 50 L phosphoric acid 1 mol L^–1 at a controlled room temperature of 15°C for 20 min. The separation of acetaldehyde-DNPH (ADNPH) was carried out on a Shimadzu Shim-pack C₁₈ column, using methanol/LiCl_(aq) 1.0 mM (80/20, v/v) as a mobile phase under isocratic elution and UV–Vis detection at 365 nm. The standard curve of ADNPH was linear in the range 3–300 mg L^–1 per injection (20 L) and the limit of detection (LOD) for acetaldehyde was 2.03 g L^–1, with a correlation coefficient greater than 0.999 and a precision (relative standard deviation, RSD) of 5.6% (n=5). Recovery studies were performed by fortifying fuel samples with acetaldehyde at various concentrations and the results were in the range 98.7–102%, with a coefficient of variation (CV) from 0.2% to 7.2%. Several fuel samples collected from various gas stations were analyzed and the method was successfully applied to the analysis of acetaldehyde in fuel ethanol samples.     

A microwave-assisted extraction method combined with magnetic ionic liquid-based dispersive liquid–liquid microextraction for the extraction of chloramine–T from fish samples prior to its determination by high-performance liquid chromatography

In the present work, a combination of microwave-assisted extraction with magnetic ionic liquid–based dispersive liquid–liquid microextraction was developed for the extraction of chloramine–T from fish samples. In this method, the sample was mixed with a hydrochloric acid solution and exposed to microwave irradiations. By doing so, chloramine–T was converted to p–toluenesulfonamide and extracted from the sample into an aqueous phase. Then, a mixture of acetonitrile (as a dispersive solvent) and magnetic ionic liquid (as an extraction solvent) was rapidly injected into the obtained solution. In the following, the magnetic solvent droplets including the extracted analytes were isolated from the aqueous solution in the presence of an external magnetic field and after diluting with acetonitrile injected into high-performance liquid chromatography equipped with a diode array detector. Under the optimum extraction conditions, high extraction recovery (78%), low limits of detection (7.2 ng/g) and quantification (23.9 ng/g), good repeatability (relative standard deviations ≤5.8 and 6.8% for intra– and inter-day precisions, respectively), and wide linear range (23.9–1000 ng/g) were obtained. Finally, various fish samples marketed in Tabriz city (East Azarbaijan, Iran) were analyzed with the suggested method.     

Dispersive liquid–liquid microextraction coupled to liquid chromatography for thiamine determination in foods

A miniaturized dispersive liquid–liquid microextraction (DLLME) procedure coupled to liquid chromatography (LC) with fluorimetric detection was evaluated for the preconcentration and determination of thiamine (vitamin B₁). Derivatization was carried out by chemical oxidation of thiamine with 5 × 10⁻⁵ M ferricyanide at pH 13 to form fluorescent thiochrome. For DLLME, 0.5 mL of acetonitrile (dispersing solvent) containing 90 μL of tetrachloroethane (extraction solvent) was rapidly injected into 10 mL of sample solution containing the derivatized thiochrome and 24% (w/v) sodium chloride, thereby forming a cloudy solution. Phase separation was carried out by centrifugation, and a volume of 20 μL of the sedimented phase was submitted to LC. The mobile phase was a mixture of a 90% (v/v) 10 mM KH₂PO₄ (pH 7) solution and 10% (v/v) acetonitrile at 1 mL min⁻¹. An amide-based stationary phase involving a ligand with amide groups and the endcapping of trimethylsilyl was used. Specificity, linearity, precision, recovery, and sensitivity were satisfactory. Calibration graph was carried out by the standard additions method and was linear between 1 and 10 ng mL⁻¹. The detection limit was 0.09 ng mL⁻¹. The selectivity of the method was judged from the absence of interfering peaks at the thiamine elution time for blank chromatograms of unspiked samples. A relative standard deviation of 3.2% was obtained for a standard solution containing thiamine at 5 ng mL⁻¹. The esters thiamine monophosphate and thiamine pyrophosphate can also be determined by submitting the sample to successive acid and enzymatic treatments. The method was applied to the determination of thiamine in different foods such as beer, brewer’s yeast, honey, and baby foods including infant formulas, fermented milk, cereals, and purees. For the analysis of solid samples, a previous extraction step was applied based on an acid hydrolysis with trichloroacetic acid. The reliability of the procedure was checked by analyzing a certified reference material, pig’s liver (CRM 487). The value obtained was 8.76 ± 0.2 μg g⁻¹ thiamine, which is in excellent agreement with the certified value, 8.6 ± 1.1 μg g⁻¹.     

Development of a fast liquid chromatography–tandem mass spectrometry method for the determination of endocrine-disrupting compounds in waters

A fast liquid chromatography-electrospray ionization-tandem mass spectrometry (LC-ESI-MS-MS) method was developed to study five endocrine-disrupting compounds (4-n-nonylphenol, bisphenol A, estrone, 17β-estradiol and 17α-ethinylestradiol) in water. Different columns were tested; the chromatographic separation of the analytes was optimized on a Pinnacle DB biphenylic column with a water–acetonitrile gradient elution, which allowed the separation of the selected endocrine-disrupting compounds (EDCs) in less than 6 min. Quantitative analysis was performed in selected reaction monitoring (SRM) mode; two transitions were chosen for each compound, using the most abundant for quantitation. Calibration curves using bisphenol A-d ₁₆ as internal standard were drawn, showing good correlation coefficients (0.9993–0.9998). All figures of merit of the method were satisfactory; limits of detection were in the low pg range for all analytes. The method was then applied to the determination of the analytes in real water samples: to this aim, polar organic chemical integrative samplers (POCIS) were deployed in the influent and in the effluent of a drinking water treatment plant in Liguria (Italy). The EDC level was rather low in the influent and negligible in the outlet, reflecting the expected function of the treatment plant.     

Reagent peak-free liquid chromatography–fluorescence analysis of carboxylic acids using a fluorous scavenging–derivatization method

We developed a fluorous scavenging–derivatization method for reagent peak-free liquid chromatography (LC)–fluorescence analysis of carboxylic acids. In this method, carboxylic acids were fluorescently derivatized with 1-pyrenemethylamine in the presence of 1-ethyl-3-(3-dimethylaminopropyl)carbodiimide and 1-hydroxy-1H-benzotriazole. Residual excess unreacted reagent was tagged with 2-(perfluorooctyl)ethyl isocyanate and could be selectively removed by microfluorous solid-phase extraction before LC analysis. With use of this method, eight fluorescent derivatives of linear aliphatic carboxylic acids (C₁–C₈) can be separated within 30 min by reversed-phase LC with gradient elution. In the chromatogram obtained, the fluorous-tagged unreacted reagent peak is greatly decreased after microfluorous solid-phase extraction and does not interfere with the quantification of each acid. With use of microfluorous solid-phase extraction with 80% (v/v) aqueous methanol elution, over 99.9% of the unreacted fluorescent reagent was removed. The detection limits (signal-to-noise ratio of 3) for the carboxylic acids examined are 2.3–8.0 fmol per 10-μL injection. We also applied this method successfully to the analysis of highly polar carboxylic acids such as α-keto acids and tricarboxylic acid cycle metabolites.     

Development and validation of a pressurized liquid extraction liquid chromatography–tandem mass spectrometry method for perfluorinated compounds determination in fish

This paper describes the development and validation of an analytical methodology to determine eight perfluorinated compounds (PFCs) in edible fish using pressurized liquid extraction (PLE) with water and solid-phase extraction (SPE) with an ion-exchanger as extraction and pre-concentration procedures, followed by liquid chromatography–quadrupole-linear ion trap mass spectrometry (LC–QqLIT–MS). The rapidity and effectiveness of the proposed extraction procedure were compared with those most commonly used to isolate PFCs from fish (ion-pairing and alkaline digestion). The average recoveries of the different fish samples, spiked with the eight PFCs at three levels (the LOQ, 10 and 100 μg kg⁻¹ of each PFC), were always higher than 85% with relative standard deviation (RSD) lower than 17%. A good linearity was established for the eight PFCs in the range from 0.003–0.05 to 100 μg kg⁻¹, with r > 0.9994. The limits of quantification (LOQs) were between 0.003 and 0.05 μg kg⁻¹, which are well below those previously reported for this type of samples. Compared with previous methods, sample preparation time and/or LOQs are reduced. The method demonstrated its successful application for the analysis of different parts of several fish species. Most of the samples tested positive, mainly for perfluoropentanoic acid (PFPA), perfluorobutane sulfonate (PFBS) and perfluorooctanoic acid (PFOA) but other of the eight studied PFCs were also present.     

A new concept of hollow fiber liquid–liquid–liquid microextraction compatible with gas chromatography based on two immiscible organic solvents

A new concept of liquid–liquid–liquid microextraction (LLLME) was introduced based on applying two immiscible organic solvents in lumen and wall pores of hollow fiber (HF). With this methodology, analytes of interest can be extracted from aqueous sample, into a thin layer of organic solvent (dodecane) sustained in the pores of a porous hollow fiber, and further into a μL volume of organic acceptor (acetonitrile or methanol) located inside the lumen of the hollow fiber. Some chlorophenols (CPs) were selected as model compounds for developing and evaluating of the method performance. The analysis was performed by gas chromatography–electron capture detection (GC–ECD) without derivatization. The factors affecting the HF-LLLME of target compounds were investigated and the optimal extraction conditions were established. Under the optimum conditions, preconcentration factors in a range of 208–895 were obtained. The performance of the proposed method was studied in terms of linear dynamic ranges (LDRs from 0.02 to 100 ng mL⁻¹), linearity (R² ≥ 0.995), precision (RSD % ≤ 8.1) and limits of detection (LODs in the range of 0.006–0.2 ng mL⁻¹). In addition to preconcentration, HF-LLLME also served as a technique for sample clean-up.     

Novel derivatisation technique for the determination of chlorophenoxy acid type herbicides by gas chromatography–mass spectrometry

The analytical detection of chlorophenoxycarboxylic-acid-type herbicides (2,4-D, dichloprop, MCPA, etc.) in environmental samples is often a problem in instrumental analysis, as these compounds containing free carboxylic groups require chemical derivatisation prior to gas chromatographic (GC) methods. Nine chlorophenoxy-acid-type herbicide active ingredients have been derivatised successfully with trimethylsilyl N,N-dimethyl carbamate and t-butyldimethylsilyl N,N-dimethyl carbamate by forming their trimethylsilyl (TMS) and t-butyldimethylsilyl (TBDMS) esters, respectively. The detection and determination of the derivatives were performed by capillary gas chromatography–mass spectrometry. The study included determination of retention indices, mass spectral properties and comparison of derivatives produced. The mass spectra of TBDMS derivatives are usually dominated by very characteristic ions [M-57]⁺ resulting from the cleavage of t-butyl moiety during electron impact (EI) ionisation in the mass spectrometer. Limits of detection were 5 to 100 pg applying GC with EI-MS detection in full scan mode. The method, using SPE sample preparation, was applied for the analysis of 115 ground water and surface water samples collected in Békés County, Hungary in 2009.