Analysis of Six Phenolic Endocrine Disrupting Chemicals in Surface Water and Sediment

An efficient and reliable method based on gas chromatography–mass spectrometry (GC–MS) was developed for the extraction and analysis of six phenolic endocrine disrupting chemicals (EDCs), such as 4-nonylphenol (4-NP), nonylphenol-mono-ethoxylate (NP1EO), nonylphenol-di-ethoxylate (NP2EO), 4-tert-octylphenol (4-t-OP), bisphenol A (BPA) and 4-cumylphenol (4-CP) in surface water and sediment. The method was developed by using microwave-assisted extraction (MAE), solid phase extraction (SPE) and derivatization procedure. The MAE procedures were performed by optimizing three key process factors, consisted of extraction solvent, extraction temperature and holding time, affecting the extraction efficiency from sediment samples. For SPE, various parameters that may affect the recovery efficiency of water samples, such as SPE phase cartridge, elution solvent, as well as pH of water samples, were investigated. A series of derivatization conditions, such as derivatization reagent, reaction temperature and reaction time, were improved. The method achieved good repeatability and reproducibility with relative standard deviations <13% for all target EDCs in the both samples. Satisfactory recoveries for spiked water and sediment samples ranged from 85 to 101% and 74 to 105%, respectively. The limits of quantification varied from 0.20 (4-t-OP) to 11.50 ng L^?1 (NP2EO) and from 0.31 (4-t-OP) to 9.50 ng g^?1 dry weight (dw) (NP2EO) for water samples and sediment samples, respectively. The established method was successfully applied to the analysis of target EDCs in surface water and sediment samples collected from Caohai site of Dianchi Lake, China. The results showed that NP1EO, NP2EO and BPA were the three dominant phenolic EDCs in the site, reaching 114, 97 and 149 ng L^?1 in surface water, while 444, 186 and 178 ng g^?1 dw in surface sediment, respectively.     

Solid phase extraction and uptake properties of multi-walled carbon nanotubes of different dimensions towards some nitro-phenols and chloro-phenols from water

Equilibrium sorption studies and solid phase extraction (SPE) of various phenols (Phenol (Ph), 2-chlorophenol (2-CP), 3-chlorophenol (3-CP), 4-chlorophenol (4-CP), 2-nitrophenol (2-NP), 4-nitrophenol (4-NP), 2,4-dinitrophenol (2,4-DNP)) on oxidized and raw multi-walled carbon nanotubes (MWCNTs) of various external diameters (10–20, 10–30, 20–40, 40–60 and 60–100?nm) and various lengths (short: 1–2?µm and long: 5–15?µm) were tested. Equilibrium sorption studies showed that 2-NP fits the Langmuir isotherm model (LIM), while the other phenolic compounds fit the Freundlich isotherm model (FIM). There was generally an inverse relation between external diameter of MWCNT and its sorption capacity towards phenolic compounds. Long MWCNT showed higher sorption capacity than short MWCNT. Thus dimensions of MWCNT play a role in retaining the sorbed molecules. Oxidation of MWCNT caused a decrease in sorption capacity of phenolic compounds of lower acidity where hydrophobic interaction is predominant, while it caused an increase in sorption capacity of phenolic compounds of higher acidity where H-bonding is predominant. The dependence of sorption on the acidity of phenols (pK_a values) indicates that the basic groups (pyrone-like groups) on the MWCNT surface play a role in the sorption process. In SPE experiments, it was found that hydrogen peroxide-oxidized MWCNT of external diameter 40–60?nm and length 5–15?µm was the best extractant at pH 6.5 using acetonitrile as eluting solvent. The optimized SPE procedure gave detection limits range: 0.027–0.202?ng?mL^?1 within the studied concentration range (10–100?ng?mL^?1). Application of the optimum SPE method on spiked tap water, reservoir water and stream water gave recovery range of 84.3–100% for 2-CP, 3-CP and 4-CP (%RSD range 2.8–9.2%); while Ph, 2-NP, 4-NP, and 2,4-DNP gave recoveries <67.6%.     

1-Butyl-3-methylimidazolium hexafluorophosphate ionic liquid-based liquid–liquid microextraction for the determination of 4-nonylphenol and 4- tert -octylphenol in environmental waters

In the present study, room-temperature ionic liquid (RTIL) 1-butyl-3-methylimidazolium hexafluorophosphate was used as extraction solvent in a liquid–liquid microextraction (LLME) procedure followed by liquid chromatography for determining 4-nonylphenol (4-NP) and 4-tert-octylphenol (4-t-OP) in environmental water samples. RTIL-based LLME was a simple, inexpensive, and fast sample preparation method, and its parameters such as extraction time, addition of salt, selection of phase ratio, and pH value were optimized. The optimized method had acceptable limits of detection (LOD) and a precision of 2?µg?L^?1 and 8.1% for 4-NP and 0.6?µg?L^?1 and 3.7% for 4-t-OP, respectively. The proposed method was successfully applied in river water and effluent from a sewage-treatment plant, and the recoveries spiked at 6?µg?L^?1 and 25?µg?L^?1 levels were in the range of 82–113%.     

Determination of biocides in different environmental matrices by use of ultra-high-performance liquid chromatography–tandem mass spectrometry

A sensitive and robust method using solid-phase extraction and ultrasonic extraction for preconcentration followed by ultra-high-performance liquid chromatography–tandem mass spectrometry (UHPLC–MS–MS) has been developed for determination of 19 biocides: eight azole fungicides (climbazole, clotrimazole, ketoconazole, miconazole, fluconazole, itraconazole, thiabendazole, and carbendazim), two insect repellents (N,N-diethyl-3-methylbenzamide (DEET), and icaridin (also known as picaridin)), three isothiazolinone antifouling agents (1,2-benzisothiazolinone (BIT), 2-n-octyl-4-isothiazolinone (OIT), and 4,5-dichloro-2-n-octyl-isothiazolinone (DCOIT)), four paraben preservatives (methylparaben, ethylparaben, propylparaben, and butylparaben), and two disinfectants (triclosan and triclocarban) in surface water, wastewater, sediment, sludge, and soil. Recovery of the target compounds from surface water, influent, effluent, sediment, sludge, and soil was mostly in the range 70–120?%, with corresponding method quantification limits ranging from 0.01 to 0.31?ng?L^?1, 0.07 to 7.48?ng?L^?1, 0.01 to 3.90?ng?L^?1, 0.01 to 0.45?ng?g^?1, 0.01 to 6.37?ng?g^?1, and 0.01 to 0.73?ng?g^?1, respectively. Carbendazim, climbazole, clotrimazole, methylparaben, miconazole, triclocarban, and triclosan were detected at low ng?L^?1 (or ng?g^?1) levels in surface water, sediment, and sludge-amended soil. Fifteen target compounds were found in influent samples, at concentrations ranging between 0.4 (thiabendazole) and 372?ng?L^?1 (methylparaben). Fifteen target compounds were found in effluent samples, at concentrations ranging between 0.4 (thiabendazole) and 114?ng?L^?1 (carbendazim). Ten target compounds were found in dewatered sludge samples, at concentrations ranging between 1.1 (DEET) and 887?ng?g^?1 (triclocarban).     

Monitoring three typical phenol endocrine disrupting compounds in drinking water of Suzhou urban area – from raw water to tap water

In this work, three typical phenol endocrine-disrupting compounds (EDCs), namely Bisphenol A (BPA), 4-nonylphenol (4-NP) and 4-tert-octyphenol (4-t-OP), were detected in water samples from the whole drinking water supply chain of seven water plants at three hydrographic periods in Suzhou, China. Almost all of the drinking water in urban area of Suzhou city is provided by the seven water plants. Every link of drinking water supply, including raw water, finished water and tap water were monitored. The results indicated that BPA and 4-NP were detected in all samples with the concentration of 0.067–0.118 μg L^?1 and 0.111–0.350 μg L^?1, respectively, while 4-t-OP could be detected in only a few raw water samples with the concentration lower than its limit of quantitation (LOQ). The levels of BPA and 4-NP in raw water were significantly different among three hydrographic periods and the highest concentration can be observed in dry period. The difference in removal efficiency of BPA and 4-NP in seven water plants was also observed among three hydrographic periods, e.g. relative higher in dry period for BPA and in flow period for 4-NP. Potential risk assessment hinted that BPA and 4-NP in raw water showed a low to medium and a medium to high risk respectively to aquatic environment, while in tap water, the health risk from BPA and 4-NP could be ignored on human.     

An improved method for simultaneous analysis of steroid and phenolic endocrine disrupting chemicals in biological samples

An improved method was developed for the simultaneous determination of eight steroid and phenolic endocrine disrupting chemicals, such as oestrone (E1), 17β-oestradiol (E2), oestriol (E3), 17α-ethynylestradoil (EE2), 4-nonylphenol (4-NP), bisphenol A (BPA), 4-tert-octylphenol (4-t-OP) and 4-cumylphenol (4-CP), in biological samples. The optimal extraction and clean-up procedures were investigated using microwave-assisted extraction (MAE), automated gel permeation chromatography (GPC) and solid phase extraction (SPE). As a consequence, the most efficient extraction was achieved by using MAE with methanol as solvent at an extraction temperature of 110°C for 20?min. The clean-up of extracts was carried out by GPC on a Biobeads S-X3 column with cyclohexane/ethyl acetate (1:1, v/v) as mobile phase. Target compounds were eluted in the fraction from 7–14?min retention time. Moreover, the cleanest extracts were obtained by solid phase extraction with C-18 cartridges after the elution with 15?mL ethyl acetate. The final sample extracts were derivatised using N,O-bis(trimethylsilyl)trifluoroacetamide (BSTFA) (1% trimethylchlorosilane, TMCS) as derivatisation reagent with pyridine as the solvent. Quantification was performed by gas chromatography-mass spectrometry (GC-MS) with electron ionisation (EI) and selected ion monitoring (SIM) mode. The method was validated by spiked samples which showed good recovery and reproducibility. The overall recoveries ranged between 55.1% and 100.6%, with relative standard deviations (RSD) of 2.3–12.7% for the entire procedure. Method detection limits (MDL) ranged from 0.3 to 0.7?ng?g^?1 dry weight (dw). Performance of the method was demonstrated by its application on tissues from fish exposed to high concentration of EDCs in the laboratory. The developed method is a promising approach for the analysis of steroid and phenolic endocrine disrupting chemicals in various biological samples.     

Electrochemical oxidation determination and voltammetric behaviour of 4-nitrophenol based on Cu2O nanoparticles modified glassy carbon electrode

Cu₂O nanoparticles (nano-Cu₂O) modified glassy carbon electrode (GCE) was fabricated and used to investigate the electrochemical behaviour of 4-nitrophenol (4-NP) by cyclic voltammetry (CV), chronoamperometry (CA), chronocoulometry (CC) and differential pulse voltammetry (DPV). Compared with GCE, a remarkable increase in oxidation peak current was observed. It indicates that nano-Cu₂O exhibits remarkable enhancement effect on the electrochemical oxidation of 4-NP. Under the optimised experimental conditions, the oxidation peak currents were propotional to 4-NP concentration in the range from 1.0?×?10^?6 to 4.0?×?10^?4?mol?L^?1 with a detection limit of 5.0?×?10^?7?mol?L^?1 (S/N?=?3). The fabricated electrode presented good repeatability, stability and anti-interference. Finally, the proposed method was applied to determine 4-NP in water samples. The recoveries for these samples were from 94.60% to 105.5%.     

Rapid Assay of Bisphenol A Released from Baby Feeding Bottles by Adsorptive Stripping Voltammetry on a Diphenylether Carbon Paste Electrode

This work reports the determination of bisphenol A (BPA) released from baby feeding bottles by adsorptive stripping voltammetry on a diphenylether carbon paste electrode (DPE-CPE). BPA was as accumulated on the surface of the DPE-CPE by an adsorptive/extractive mechanism at ?0.20 V in B-R buffer at pH 7.0. Following pre-concentration, an anodic scan was applied in the range ?0.20 V to +1.00 V during which BPA was oxidized and the oxidation peak current was related to the BPA concentration in the sample. The parameters related to both the preconcentration and stripping step were investigated. Using the selected conditions, the limit of detection for BPA was 7.8 × 10^?9 mol L^?1 at a preconcentration time of 240 s and the % relative standard deviation was 4.2% for 6.7 × 10^?7 mol L^?1 of BPA (n = 8). The proposed method was applied to the determination of BPA leaching from polycarbonate baby feeding bottles under simulated conditions of typical use. The results compared well with those obtained with liquid chromatography-tandem mass spectrometry (LC-MS/MS).     

Sensitive determination of bisphenol A in plastic products by derivative voltammetry using an acetylene black paste electrode coated with salicylaldehyde-modified chitosan

A sensitive and reliable electrochemical method was developed for determination of bisphenol A (BPA) in plastic products using an acetylene black paste electrode coated with salicylaldehyde-modified chitosan (denoted as S-CHIT/ABPE). In the second-order derivative linear sweep voltammetry technique, BPA yielded a very sensitive and well-defined oxidation peak at 842?mV in 0.2?mol?L^?1 HCl solution. Owing to its unique structure and extraordinary properties, S-CHIT/ABPE showed higher accumulation efficiency toward BPA compared with bare ABPE, and significantly enhanced the oxidation peak current of BPA. Under the optimum conditions, the oxidation peak current was proportional to the concentration of BPA over the range of 4.0?×?10^?8?mol?L^?1?～?1.0?× 10^?5?mol?L^?1. The detection limit (S/N?=?3) was 2.0?×?10^?8?mol?L^?1. The fabricated S-CHIT/ABPE not only exhibited strong adsorption capacity toward BPA, but also provided remarkable stable and quantitatively reproducible analytical performance. Additionally, this newly-developed method possesses some obvious advantages including high sensitivity, extreme simplicity, rapid response and low cost.     

Determination of total antimony(III,V) by square-wave anodic stripping voltammetry with in situ plated bismuth-film electrode

A sensitive and reliable method is described for the determination of total Sb(III,?V) at traces levels by Osteryoung square-wave anodic stripping voltammery (OSWASV). This method is based on the co-deposition of Sb(III,?V) with Bi(III) onto an edge-plane pyrolytic graphite substrate at an accumulation step. OSWASV studies indicated that the co-deposited antimony was oxidised with anodic scans to give an enhanced anodic peak at about 450?mV vs. Ag/AgCl (sat. KCl). The anodic stripping peak current was directly proportional to the total concentration of antimony in the ranges of 0.01–0.10?µg?L^?1, 0.10–1.0?µg?L^?1 and 1.0–18.0?µg?L^?1 with correlation coefficient higher than 0.995 when 2.0?mol?L^?1 hydrochloric acid was used. The detection limits calculated as S/N?=?3 was 5.0?ng?L^?1 in 2.0?mol?L^?1 hydrochloric acid at 180?s deposition time. The relative standard deviation was 5% (n?=?6) at 0.10?µg?L^?1 level of antimony. The analytical results demonstrate that the proposed method is applicable to analyses of real water samples.     

Determination of acidic pharmaceutical products and carbamazepine in roughly primary-treated wastewater by solid-phase extraction and gas chromatography–tandem mass spectrometry

A gas chromatography–tandem mass spectrometry (GC–MS/MS) method has been developed for the determination of selected pharmaceutical residues (carbamazepine, salicylic acid, clofibric acid, ibuprofen, 2-hydroxy-ibuprofen, fenoprofen, naproxen, ketoprofen, diclofenac, and triclosan) in sewage influent and roughly primary-treated effluent. The method involved solid-phase extraction (SPE) with polymeric sorbents, and two SPE cartridges were compared for the extraction and elution of the targeted compounds in complex matrices. A successful chemical derivatization of carbamazepine and acidic compounds using N,O-bis(trimethylsilyl) trifluoroacetamide +10% trimethylchlorosilane is also described. The quantification limits of the analytical procedure ranged from 30 to 60?ng?L^?1 for 500?mL of wastewater. The best recovery rates (72–102%) in spiked effluent samples were obtained with Phenomenex Strata-X? cartridges. Detection limits (S/N?=?3) were estimated at between 1 and 18?ng?L^?1. The reported GC–MS/MS method significantly reduces the strong matrix effects encountered with more expensive LC-MS/MS techniques. Application of the developed method showed that most selected analytes were detected at concentrations ranging from low µg?L^?1 to trace level ng?L^?1 in Montreal's wastewater treatment plant effluent and influent, as well as in the receiving waters at more than 8?km downstream of the effluent outfall. The rugged alternative analytical method is suitable for the simultaneous analysis of carbamazepine and pharmaceutical acidic residues in wastewater samples from influents and effluents that have undergone rough primary treatment.     

Determination of cadmium and lead in aqueous environmental samples after complexation and microextraction onto the surface of an empty solvent-impregnated polypropylene fibre coupled with electrothermal AAS

A procedure based on polypropylene hollow-fibre preconcentration coupled with electrothermal atomic absorption spectrometry (ETAAS) was developed for the determination of cadmium and lead in seawater, wastewater, tap water and lake water samples. The n-octanol was immobilised in the pores of the polypropylene hollow fibre, which was used as the liquid sorption membrane negating the need for acceptor liquid phase in the lumen. The metal ions were extracted from water samples onto the impregnated fibre, as ammonium pyrrolydine dithiocarbamate (APDC) complexes, and then back-extracted into a small volume of 0.1?mol?L^?1 HNO₃. The main extraction-related parameters were properly evaluated and an interference study was carried out. Linear regression lines were plotted and replicate analyses of real samples revealed that the proposed method is precise and accurate, able to be applied in routine analysis with detection limits of 4?ng?L^?1 and 12?ng?L^?1 for Cd and Pb, respectively.     

Gas-phase chemiluminescent determination of inorganic selenium in water samples following flow injection hydride generation and cryotrapping

We describe a method for the determination of inorganic selenium in water samples via gas-phase chemiluminescence (GPCL). Se(IV) was first derivatized with 4-nitro-o-phenylenediamine to form 5-nitropiazselenol. The latter was decomposed by persulfate through photocatalytic oxidation to give Se(VI), which was reduced to Se(IV). Selenium hydride was generated from Se(IV) through reduction with sodium borohydride and then preconcentrated using cryotrapping. The cryotrapped hydride was evaporated and carried to a reaction chamber by a stream of helium, where it produced GPCL as a result of ozonation. The method exhibits a wide linear calibration range (from 0.5?μg?L^?1 to 1.0?mg?L^?1) with a detection limit of 0.12?μg?L^?1 (for n?=?11), and a relative standard deviation of 3.90?% (at n?=?11) at 5.0?μg?L^?1 level of selenium. The method was applied to the determination of inorganic selenium in water samples and gave satisfactory results.

A new solid-phase extraction disk based on a sheet of single-walled carbon nanotubes

A new kind of solid-phase extraction disk based on a sheet of single-walled carbon nanotubes (SWCNTs) is developed in this study. The properties of such disks are tested, and different disks showed satisfactory reproducibility. One liter of aqueous solution can pass through the disk within 10–100 min while still allowing good recoveries. Two disks (DD-disk) can be stacked to enrich phthalate esters, bisphenol A (BPA), 4-n-nonylphenol (4-NP), 4-tert-octylphenol (4-OP) and chlorophenols from various volumes of solution. The results show that SWCNT disks have high extraction ability for all analytes. The SWCNT disk can extract polar chlorophenols more efficiently than a C₁₈ disk from water solution. Unlike the activated carbon disk, analytes adsorbed by the new disks can be eluted completely with 8–15 mL of methanol or acetonitrile. Finally, the DD-disk system is used to pretreat 1000-mL real-world water samples spiked with BPA, 4-OP and 4-NP. Detection limits of 7, 25, and 38 ng L⁻¹ for BPA, 4-OP, and 4-NP, respectively, were achieved under optimized conditions. The advantages of this new disk include its strong adsorption ability, its high flow rate and its easy preparation. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Optimization of a SPME/GC/MS Method for the Simultaneous Determination of Pharmaceuticals and Personal Care Products in Waters

A headspace solid phase microextraction (HS-SPME) method coupled with gas chromatography and MS detection (GC/MS) was optimized for the simultaneous determination of 21 target Pharmaceuticals and Personal Care Products (PPCPs) in water samples. The analytes included fragrances, UV-filters, antiseptics, estrogens, anti-inflammatory drugs, and pesticides. An on-fiber SPME derivatization, using silyl reagents, was performed for the analysis of more polar acidic compounds. An experimental design approach was applied to systematically investigate and optimize the operative parameters affecting the extraction recovery, namely: extraction temperature and time, derivatization time, desorption temperature and time. The optimum operating conditions were: extraction time of 125?min at a temperature of 40?°C; derivatization time of 30.5?min; desorption time of 2?min at a temperature of 300?°C. Under these conditions, good reproducibility was assessed as RDS% values ≤10% for underivatized PPCPs and ≤20% for derivatized compounds. The method detection limits (LOD) were between 0.7 and 9.0?ng?L^?1, with the highest values in the range 2.5–9.0?ng?L^?1 for the derivatized analytes. Method accuracy was evaluated on spiked tap water samples: recoveries varied from 85 to 103% and from 75 to 110% for non-derivatized and derivatized compounds, respectively.     

Development and optimisation of a GC-MS method for the evaluation of oestrogens and persistent pollutants in river and seawater samples

This paper describes the development and validation of a GC-MS method which allows the simultaneous quantification of 11 endocrine disrupting compounds (EDCs) in surface water samples from both estuary and sea. The analysed EDCs are oestrone (E1), 17β-estradiol (E2), 17α-ethynylestradiol (EE2), 4-tert-octylphenol, 4-n-octylphenol, 4-nonylphenol, bisphenol A and finally, mono and diethoxylates of 4-nonylphenol and 4-octylphenol. The method includes the pre-concentration of water samples, 1000-fold factor, in OASIS HLB cartridges by solid phase extraction, the derivatisation of all EDCs by N,O-bis(trimethylsilyl)trifluoroacetamide added with 1% trimethylchlorosilane and pyridine (at 65°C for 30?min) and, finally the stabilisation of the EDCs-silylated derivatives, in hexane, for 72?h. The validation parameters revealed that this method was highly specific for all target compounds using real samples. The linearity of the calibration curves (r ²) showed correlation factors higher than 0.990. The detection limits ranged from 0.10 to 1.45?ng?L^?1, depending on each analysed compound, and recoveries were satisfactory for most of the assayed EDCs (>60%). Analysis of samples from four polluted areas of Douro River estuary and from two points of the Atlantic Ocean (Portugal) showed high amounts of E1 (up to 1.96?ng?L^?1), E2 (up to 14.36?ng?L^?1) and EE2 (up to 2.76?ng?L^?1).     

Determination of phosphate in freshwater samples by flow-injection with lucigenin chemiluminescence

Lucigenin chemiluminescence (CL) in conjunction with flow-injection analysis (FIA) is used for the determination of phosphate in freshwater samples. The procedure is based on the formation of molybdophosphoric heteropoly acid (MoP–HPA) by the reaction of phosphate and ammonium molybdate under acidic conditions. CL emission was observed as a result of oxidation of lucigenin in aqueous sodium hydroxide solution in the presence of MoP–HPA. Calibration was linear up to 500?µg?L^?1 (r ^2?=?0.9998; n?=?8), with a detection limit (S/N?=?3) of 0.95?µg?L^?1. An injection throughput of 120 h^?1, and relative standard deviation (RSD; n?=?4) of 1.3–3.2% were achieved in the concentration range studied. An on-line chelating column was used to remove interfering cations. The method was applied to freshwater samples, and the results (51?±?1.0 – 107?±?2.0?µg?L^?1) did not differ significantly from results obtained using a spectrophotometric method (52.5?±?1.0 – 102?±?2.0?µg?L^?1) at 95% confidence level (t-test).     

Observations on toxicologically relevant arsenic in urine in adult offspring of families with Balkan Endemic Nephropathy and controls by batch hydride generation atomic absorption spectrometry

The aim of this study was to develop a method for the characterization of internal exposure to arsenic, which is thought to play a role in the development of a kidney disease, known as Balkan Endemic Nephropathy, typical for a district in Bulgaria, and to investigate whether the As body burden differs in the offspring versus control individuals. For this case study, an analytical procedure for the determination of toxicologically relevant arsenic (the sum of arsenite, arsenate, monomethylarsonate, and dimethylarsinate) in urine by batch-type hydride generation atomic absorption spectrometry was developed. Optimization experiments for levelling off the sensitivity of inorganic arsenic and its mono- and dimethylated species in dilute HCl–L-cysteine medium were performed. The limit of detection for hydride forming arsenic fraction was 0.5?ng As, i.e. 0.25?µg?L^?1 in 10?mL of 1?+?4 v/v diluted urine. The relative standard deviation was typically 1.5–1.8% for aqueous solution and 2–6% for urine samples at 1.0?µg?L^?1 As. The sample throughput rate was 15?h^?1. No statistical correlation and cross-correlation between individuals case-control and sex at 95% confidence were found: controls (n?=?99), mean 3.5?±?2.1 (SD), range 0.9–10.4, median 3.0?µg?L^?1 As and cases (n?=?102), mean 3.6?±?2.2 (SD), range 0.5–11.0, median 3.2?µg?L^?1 As. On the basis of this study, arsenic can be excluded as a factor involved in BEN development.     

Spectrophotometric determination of Chromium(VI) using cyclam as a reagent

A simple, rapid, sensitive, and inexpensive method for spectrophotometric determination of chromium(VI), based on the absorbance of its complex with 1,4,8,11-tetraazacyclotetradecane (cyclam) is presented. The complex showed a molar absorbtivity of 1.5?×?10⁴?L?mol^?1?cm^?1 at 379?nm. Under optimum experimental conditions, a pH of 4.5 and 1.960?×?10³?mg?L^?1 cyclam were selected, and all measurements were performed 10?min after mixing. Major cations and anions did not show any interference; Beer's law was applicable in the concentration range 0.2–20?mg?L^?1 with a detection limit of 0.001?mg?L^?1. The standard deviation in the determination is ±0.5?mg?L^?1 for a 15.0?mg?L^?1 solution (n?=?7). The described method provides a simple and reliable means for determination of Cr(VI) in real samples.     

Determination of phenoxy herbicides in water samples using phase transfer microextraction with simultaneous derivatization followed by GC‐MS analysis

A sensitive and accurate method for the determination of two model phenoxy herbicides, 4‐chloro‐2‐methylphenoxy acetic acid and 4‐chloro‐2‐methylphenoxy propanoic acid, in water is explained. This method utilizes a simple phase transfer catalyst‐assisted microextraction with simultaneous derivatization. Factors affecting the performance of this method including pH of the aqueous matrix, temperature, extraction duration, type and amount of derivatization reagents, and type and amount of the phase transfer catalyst are examined. Derivatization and the use of phase transfer catalyst have proven to be especially vital for the resolution of the analytes and their sensitive determination, with an enrichment factor of 288‐fold for catalyzed over noncatalyzed procedure. Good linearity ranging from 0.1 to 80 μg L^?1 with correlation of determination (r²) between 0.9890 and 0.9945 were obtained. Previous reported detection limits are compared with our new current method. The low LOD for the two analytes (0.80 ng L^?1 for 4‐chloro‐2‐methylphenoxy propanoic acid and 3.04 ng L^?1 for 4‐chloro‐2‐methylphenoxy acetic acid) allow for the determination of low concentrations of these analytes in real samples. The absence of matrix effect was confirmed through relative recovery calculations. Application of the method to seawater and tap water samples was tested, but only 4‐chloro‐2‐methylphenoxy propanoic acid at concentrations between 0.27 ± 0.01 and 0.84 ± 0.06 μg L^?1 was detected in seawater samples.