Estimating the PDMS-Coated, SPME-Fibre/Water- and Fibre/Gas-Partition Coefficients of Chlorinated Ethenes by Headspace-SPME

In this work, a simple, fast and reproducible method is presented for the determination of fibre/liquid-phase and fibre/gas-phase partition coefficients of five chlorinated ethenes on a poly-(dimethylsiloxane), PDMS-coated, solid-phase microextraction fibre, by employing a headspace HS-SPME coupled with gas chromatography. The partition coefficients were estimated by a numerical method using a Level-I fugacity method coupled with parameter-estimation software. Dimensionless partition coefficients between SPME fibre and liquid as well as gas phases were obtained at temperatures of 10 °C, 25 °C and 30 °C. The partition coefficients of the fibre and the gas phase, K _fg, increase with decreasing temperature by a factor of ≈2 to 6, and they are directly proportional to the linear slope of the regression line. The same tendency is observed for the partition coefficient of the fibre and liquid phase, K _fw, in a factor ≈1.2 to 2.0. The sorption enthalpy is higher in the gas phase; therefore, the sorption onto the fibre is favoured at lower temperatures. The correlation of the log K _ow versus log K _fw and log K _oa versus log K _fg shows a linear relationship with the number of chlorine atoms in the C = C molecule. Long-term experiments resulted in sorption to Teflon surfaces and possible losses in 43 mL vials, not observed in 250 mL Boston bottles.     

Use of direct immersion solid-phase microextraction on polyacrylate and polydimethylsiloxane stationary phases for simultaneous determination of the neutral and basic pharmaceuticals in wastewater

Direct immersion solid-phase microextraction has been optimized and applied to the simultaneous determination of the neutral and basic pharmaceuticals: caffeine, carbamazepine, clomipramine, chlorprothixene and clotrimazole at low concentrations in municipal wastewater. Two absorption type stationary phases: polydimethylsiloxane (PDMS) and polyacrylate (PA) have been found to be most effective for extraction of target analytes. The separation and detection were carried out by gas chromatograph coupled with mass spectrometer working in the selected ion monitoring mode. The method was validated for linearity, detection and quantitation limits, selectivity and precision. The average correlation coefficient of the calibration curves was 0.9933. The LOD values in influent and effluent wastewater were in the range of 10–145 ng L^?1 and 4–111 ng L^?1, respectively, which were a bit higher than those in the deionized water due to matrix effect. The high values of distribution coefficient (K _fs ) in PDMS/water and PA/water systems (log K _fs between 3.05 and 4.23) indicates the very high applicability of these stationary phases for determination of carbamazepine, clomipramine, chlorprothixene and clotrimazole in water samples.

Open image in new window

     

A Novel QSAR Approach for Estimating Toxicity of Phenols

Abstract

Toxicity values (log IGC^?1 ₅₀) for 60 phenols tested in the 2-d static population growth inhibition assay with the ciliate Tetrahymena pyriformis were tabulated. Each chemical was selected so the series formed uniform coverage of the hydrophobicity/ionization surface. A high quality hydrophobicity-dependent (log K _ow) structure-toxicity relationship (log IGC^?1 ₅₀ = 0.741 (log K_ow) ?1.433; n = 17; r² = 0.970; s = 0.134; F = 486.55; Pr > F = 0.0001) was developed for phenols with pK_a values > 9.8. Similarly, separate hydrophobicity-dependent relationships were developed for phenols with pK_a values of 4.0, 5.1, 6.3, 7.5, and 8.7. Comparisons of intercepts and slopes, respectively, revealed phenols with pK_a values of 6.3 to be the most toxic and the least influenced by hydrophobicity. These relationships were reversed for the more acidic and basic phenols. Plots of toxicity versus pK_a for nitro-substituted phenols and phenols with log K_ow values of either 1.75 or 2.50 further demonstrated bilinearity between toxicity and ionization. In an effort to more accurately model the relationship between toxicity and ionization, the absolute value function |6.3-pK_a| was used to model ionization affects for derivatives with pK_a values between 0 and 9.8. For derivatives with pK_a value > 9.8, a value of 3.50 was used to quantitate ionization effects. The use of log K_ow in conjunction with this modified pK_a (ΔpK_a) resulted in the structure-toxicity relationship (log IGC^?1 ₅₀ = 0.567 (log K_ow)-0.226 (ΔpK_a-0.079; n = 54; r² = 0.926; s = 0.215; F = 321.06; Pr > F = 0.0001). Derivatives with a nitro group in the 4-position typically did not model well with the above equation.     

Predicting 1-octanol-water partition coefficient by high-performance liquid chromatography gradient elution

The method to predict 1-octanol-water partition coefficients (K _ow) from capacity factors (k) obtained by Reversed-Phase High-Performance Liquid Chromatography (RP-HPLC) has been extended to use gradient elution rather than isocratic elution. The mobile phase has been changed either linearly or exponentially with time. The initial composition of the mobile phase and its rate of change affected the log K _ow versus log k relation. This relation was exponential in linear gradient experiments. For non-linear gradient elution in which the water fraction of the mobile phase decreased exponentially from 100% to approach 0% asymptotically, a physically-based equation describing the dependence of log K _ow on log k has been derived. Without any preliminary estimation, RP-HPLC gradient elution allows a precise prediction of log K _ow over a range of nearly six orders of magnitude.     

Water solubility and octanol/water-partitioning of hydrophobic chlorinated organic substances determined by using SPME/GC

The critical step in the determination of water solubilitiy (S _w) and octanol-water partition coefficient (K _ow) of hydrophobic organic chemicals by using the generator-column technique and the slow-stirring procedure, respectively, is the exact quantification of the low water-phase concentrations of the substances under investigation. We have tested the applicability of solid-phase microextraction (SPME) and gas chromatography with seven chlorinated organic compounds. The substances cover a S _w range from 500 mg/L to 7 ng/L and a log K _ow range from 3 to 8. The results show that SPME can be a valuable alternative to common preconcentration techniques in the quantification of hydrophobic organics in pure and octanol-saturated water. The apparent SPME distribution constants K _SPME (obtained with the 100 μm-PDMS fiber for analyte’s partitioning between fiber coating and aqueous sample) do not correlate directly with octanol/water partition coefficients and thus cannot be recommended as a surrogate parameter for K _ow. Received: 15 January 1997 / Revised: 2 May 1997 / Accepted: 8 May 1997     

Dependence of the distribution constant in liquid–liquid partition equilibria on the van der Waals molecular surface area

The direct calculation of free energy of interactions between a solute j and two immiscible liquids shows a linear dependence between the (logarithm of) the distribution constant in liquid–liquid partition equilibrium log K_j and the van der Waals surface area of the solute. The study provides a thermodynamic proof for the formula log K_BA,j = c₁ log K_BC,j + c₂ that describes the linear dependence between (the logarithm of) the distribution constant for a solute j in a solvent system (B/A) and (the logarithm of) the distribution constant for the same solute in a different solvent system (B/C). This relation has been well proven by various experimental studies and it is frequently used in liquid chromatographic separations as well as in liquid–liquid extractions, but was not explained previously based on thermodynamic results. The theory was verified using the prediction of octanol/water distribution constants log K_ow for a wide range of molecules, including hydrocarbons and compounds with a variety of functional groups. The results have also been verified for the distribution constants in other solvent systems. The expression for the distribution constant obtained in this study also gives a theoretical base for the additive fragment methodology used for the prediction of log K_ow.     

Liquid–liquid extraction of Cu(II), Co(II) and Ni(II) with salicylidèneaniline from sulphate media

For a fundamental study on the development of novel extraction divalent metal, the extraction behaviour of copper(II), cobalt(II) and nickel(II) is studied with salicylidèneaniline (SAN). The phenol group in the Schiff base moiety leads to a large increase in the percentage of transition metal ions. SAN has both good reactivity towards metal ions and solubility in organic solvents. The solvent extraction of copper(II), cobalt(II) and nickel(II) with salicylidèneaniline from sulphate media is studied with the following parameters: pH, concentration of the extractant and the nature of diluent. The stoichiometry coefficients of the extracted species are determined by the slope analysis method. The extraction reaction proceeds by cation exchange mechanism and the extracted species are: CuL₂HL, CoL₂HL and NiL₂. The extaction constants are evaluated for the different diluents. Under suitable conditions of pH, the solvent extraction of cobalt(II) and nickel(II) in different diluents leads to third phase formation. This tendency is confirmed from numerical extraction constants for both metal cations (log?K _ex?=??15.10?±?0.03 for nickel(II) in CHCl₃) and (log?K _ex?=??12.56?±?0.04 for cobalt(II) in CHCl₃). The extraction efficiency is found to follow the order Cu(II)?>?Co(II)?>?Ni(II).     

Assessment of Centrifugal Partition Chromatography for Determination of Octanol-Water Partition Coefficients

Abstract

Centrifugal partition chromatography (CPC) has been assessed as a convenient automated method for the determination of octanol-water partition coefficients (K_OW) over the range of -0.5 to 2.5 log units. The stationary (V_s) and mobile phase (V_m) volumes, which are needed for the calculation of K_ow, are determined in situ by injecting four compounds with known K_ow. V3 and V_m were also determined by independent analytical means to demonstrate that this is a direct measurement of K_ow from fundamental chromatographic principles with no unexplained fitted parameters. Propagation of error shows that a single four-component calibration with duplicate injections of each unknown is sufficient to determine log K_ow with a precision of less than 0.1 log units.     

Nonlinear Dependence of Bioconcentration Factors on n-Octanol-Water Partition Coefficients of Chlorinated Dibenzofurans and Dibenzo-p-Dioxins

Abstract

A nonlinear thermodynamic model is applied to the prediction of both the bioconcentration factor (K_bw) in the guppy (Poecilia reticulata) and the n-octanol-water partition coefficient (K_ow) of chlorinated dibenzofurans and dibenzo-p-dioxins. To this end molar liquid volumes, heats of vaporization and empirically fitted parameters of the pertinent solute and solvents are used. Calculated log K_bw and log K_ow values are obtained with correlation coefficients (r = 0.85 and 0.992) and mean deviations (< dev > = 0.19 and 0.17), which compare favourably with experimental data.

In addition the model enables an explanation of the well-known nonlinear log-log relationship between the two properties for compounds with high K_ow values on the basis of differences between the properties of biotic lipid and n-octanol. It is suggested that the breakdown of the linear relationship is caused by entropic effects related to the number of chlorine atoms in the solute molecules and to the structures of the lipid and n-octanol.     

Reversed phase liquid chromatography of PCBs as a basis for the calculation of water solubility and log Kow for polychlorobiphenyls

Summary Water solubility (S _w) and log K _ow values have been determined for 154 possible polychlorobiphenyls using the retention indices obtained by RP-HPLC and structurally selected PCB congeners with known log K _ow values for the regression lines. The water solubility data are melting point corrected.

---

Umkehrphasen-Flüssig-Chromatographie von PCBs als Grundlage zur Berechnung der Wasserlöslichkeit und des log K _ow für Polychlorbiphenyle

---

Dedicated to Prof. Dr. W. Fresenius on the occasion of his 75th birthday     

Evaluation of solid-phase microextraction with PDMS for air sampling of gaseous organophosphate flame-retardants and plasticizers

As an inexpensive, simple, and low-solvent consuming extraction technique, the suitability of solid-phase microextraction (SPME) with polydimethylsiloxane (PDMS) sorbent was investigated as a quantitative method for sampling gaseous organophosphate triesters in air. These compounds have become ubiquitous in indoor air, because of their widespread use as additive flame retardants/plasticizers in various indoor materials. Results obtained by sampling these compounds at controlled air concentrations using SPME and active sampling on glass fibre filters were compared to evaluate the method. A constant linear airflow of 10 cm s^–1 over the fibres was applied to increase the extraction rate. For extraction of triethyl phosphate with a 100-m PDMS fibre, equilibrium was achieved after 8 h. The limit of detection was determined to be less than 10 pg m^–3. The PDMS–air partition coefficients, K_fs, for the individual organophosphate triesters were determined to be in the range 5–60×10⁶ at room temperature (22–23°C). Air measurements were performed utilising the determined coefficients for quantification. In samples taken from a lecture room four different airborne organophosphate esters were identified, the most abundant of which was tris(chloropropyl) phosphate, at the comparatively high level of 1.1 g m^–3. The results from SPME and active sampling had comparable repeatability (RSD less than 17%), and the determined concentrations were also similar. The results suggest that the investigated compounds were almost entirely associated with the gaseous phase at the time and place sampled.     

HPLC method with on-line SPE preconcentration for quantification of permethric acid sorption to goethite

Pesticide metabolites are often found to be more mobile in soil than their parent compounds. Pyrethroids are bound strongly to soil and therefore sorption of the pyrethroid metabolite permethric acid (PA) to a typical soil sorbent, goethite, was investigated. An on-line solid-phase extraction (SPE)-HPLC-UV procedure was developed for quantification of trans- and cis-permethric acid in aqueous samples. Limits of detection (LOD) were 500 times lower than those obtained with conventional HPLC-UV, resulting in LODs of 1.4 and 0.3?nM for the trans- and cis-isomers, respectively. Sorption of nanomolar concentrations of PA to goethite was found to be specific up to less than 1% surface coverage. In this range the data was described by a Langmuir equation with K _ads = 7.1 × 10^?9?L/mol and Γ_max = 7.1 × 10^?9?mol/m² for total PA (trans + cis) at pH = 3. K _ads,?cis (1.4 × 10⁶?L/mol) was approximately twice K _ads,?trans (7.9 × 10⁵?L/mol). At higher PA concentrations the slope of the sorption isotherm increased, which is ascribed to hydrophobic interactions between adsorbed and dissolved PA molecules. Based on comparison with reported K _om values, metal oxides are expected to have a relatively greater significance to the retention of PA than soil organic matter.     

Headspace solid-phase microextraction-gas chromatography-quadrupole mass spectrometric methodology for the establishment of the volatile composition of Passiflora fruit species

Dynamic headspace solid-phase microextraction (HS-SPME) followed by thermal desorption gas chromatography-quadrupole mass spectrometry analysis (GC-_qMS), was used to investigate the aroma profile of different species of passion fruit samples. The performance of five commercially available SPME fibres: 65 μm polydimethylsiloxane/divinylbenzene, PDMS/DVB; 100 μm polydimethylsiloxane, PDMS; 85 μm polyacrylate, PA; 50/30 μm divinylbenzene/carboxen on polydimethylsiloxane, DVB/CAR/PDMS (StableFlex); and 75 μm carboxen/polydimethylsiloxane, CAR/PDMS; was evaluated and compared. Several extraction times and temperature conditions were also tested to achieve optimum recovery. The SPME fibre coated with 65 μm PDMS/DVB afforded the highest extraction efficiency, when the samples were extracted at 50 °C for 40 min with a constant stirring velocity of 750 rpm, after saturating the sample with NaCl (17%, w/v — 0.2 g). A comparison among different passion fruit species has been established in terms of qualitative and semi-quantitative differences in volatile composition. By using the optimal extraction conditions and GC-qMS it was possible to tentatively identify seventy one different compounds in Passiflora species: 51 volatiles in Passiflora edulis Sims (purple passion fruit), 24 in P. edulis Sims f. flavicarpa (yellow passion fruit) and 21 compounds in Passiflora mollissima (banana passion fruit). It was found that the ethyl esters comprise the largest class of the passion fruit volatiles, including 82.8% in P. edulis variety, 77.4% in P. edulis Sims f. flavicarpa variety and 39.9% in P. mollissima.The semi-quantitative results were then submitted to principal component analysis (PCA) in order to establish relationships between the compounds and the different passion fruit species under investigation.     

Screening of volatile composition from Portuguese multifloral honeys using headspace solid-phase microextraction-gas chromatography-quadrupole mass spectrometry

The volatile composition from four types of multifloral Portuguese (produced in Madeira Island) honeys was investigated by a suitable analytical procedure based on dynamic headspace solid-phase microextraction (HS-SPME) followed by thermal desorption gas chromatography-quadrupole mass spectrometry detection (GC-qMS). The performance of five commercially available SPME fibres: 100 μm polydimethylsiloxane, PDMS; 85 μm polyacrylate, PA; 50/30 μm divinylbenzene/carboxen on polydimethylsiloxane, DVB/CAR/PDMS (StableFlex); 75 μm carboxen/polydimethylsiloxane, CAR/PDMS, and 65 μm carbowax/divinylbenzene, CW/DVB; were evaluated and compared. The highest amounts of extract, in terms of the maximum signal obtained for the total volatile composition, were obtained with a DVB/CAR/PDMS coating fibre at 60 °C during an extraction time of 40 min with a constant stirring at 750 rpm, after saturating the sample with NaCl (30%). Using this methodology more than one hundred volatile compounds, belonging to different biosynthetic pathways were identified, including monoterpenols, C₁₃-norisoprenoids, sesquiterpenes, higher alcohols, ethyl esters and fatty acids. The main components of the HS-SPME samples of honey were in average ethanol, hotrienol, benzeneacetaldehyde, furfural, trans-linalool oxide and 1,3-dihydroxy-2-propanone.     

Optimization of Modern Analytical SPME and SPDE Methods for Determination of <Emphasis Type="Italic">Trans</Emphasis>-2-nonenal in Barley,Malt and Beer

Trans-2-nonenal is an aldehyde contributing to an unpleasant off-flavor and odor of rancid butter in stored beer. The automated solid-phase microextraction technique (SPME) coupled with gas chromatography (GC) and solid-phase dynamic extraction (SPDE) coupled with gas chromatography were optimized and introduced to determine trans-2-nonenal in barley, malt and beer. Five types of SPME fibers coated with different stationary phases (100 μm PDMS, 65 μm PDMS/DVB, 85 μm CAR/PDMS, 50/30 μm DVB/CAR/PDMS, 85 μm PA) and two needles (PDMS, PDMS/AC) were compared and tested for their efficiencies in the headspace (HS) SPME and SPDE determination of trans-2-nonenal in barley, malt and beer. The highest extraction efficiency of HS-SPME was achieved with the PDMS/DVB fiber, and addition of 1.5 g of NaCl, extraction time was 20 min at 60 °C. The highest extraction efficiency of HS-SPDE was obtained with the PDMS needle, 15 extraction strokes at 60 °C and addition of 1.5 g of NaCl. Trans-2-nonenal was identified with the method of HS-SPME coupled gas chromatography-mass spectrometry (GC–MS); the samples were analyzed using the HS-SPME-GC-coupled gas chromatography-flame ionization detector (GC-FID) technique.     

Automatic flow system for evaluation of polystyrene-divinylbenzene sorbents applied to preconcentration of phenolic pollutants

In this work, an evaluation of commercially available polystyrene-divinylbenzene sorbents for solid-phase extraction (SPE) of eleven phenolic compounds is intended. Considering the particle size and cross-linking degree, Amberlite XAD-4 (commercial or grounded), Macronet MN-200 and Lichrolut EN were tested. The SPE protocol was performed by an automatic system, providing repeatable experimental conditions for assessment of sorbent capacity, breakthrough volume and enrichment factor (EF). A positive correlation between EF and log?K _ow was found for Amberlite XAD-4 while a negative correlation was observed between EF and molecular weight of analyte for Macronet MN-200 and for Lichrolut EN. This indicates a prevalence of hydrophobic interactions or molecular exclusion depending upon the polymer cross-linking degree. Despite the similar repeatability (RSD?<?4.7%, n?>?6) and recovery values attained (97.6–102.7%, using 50?mL of sample) for all sorbents, Lichrolut EN is the best choice for analytical application as higher EF and lower LOD values (between 18 and 207?ng) were attained for this sorbent.     

Water solubility and octanol/water-partitioning of hydrophobic chlorinated organic substances determined by using SPME/GC

The critical step in the determination of water solubilitiy (S _w) and octanol-water partition coefficient (K _ow) of hydrophobic organic chemicals by using the generator-column technique and the slow-stirring procedure, respectively, is the exact quantification of the low water-phase concentrations of the substances under investigation. We have tested the applicability of solid-phase microextraction (SPME) and gas chromatography with seven chlorinated organic compounds. The substances cover a S _w range from 500 mg/L to 7 ng/L and a log K _ow range from 3 to 8. The results show that SPME can be a valuable alternative to common preconcentration techniques in the quantification of hydrophobic organics in pure and octanol-saturated water. The apparent SPME distribution constants K _SPME (obtained with the 100 μm-PDMS fiber for analyte’s partitioning between fiber coating and aqueous sample) do not correlate directly with octanol/water partition coefficients and thus cannot be recommended as a surrogate parameter for K _ow.