Multi-Residue Analysis by Liquid Chromatography-Mass Spectrometry Coupling. Application to Drinking and River Waters

Abstract

The coupling between liquid chromatography and mass spectrometry with an APCI or ESI interface (in positive or negative mode) is used here for multi-residue analyses in natural waters, covering basic and neutral pesticides as well as acid pesticides. The methods developed are applied to drinking and, river waters after the samples are concentrated by liquid-liquid extraction or solid phase extraction on C18 cartridges. Comparisons are made between UV detection and mass spectrometry and between two chromatographic methods for acid substances. The quantitation limits range from 0.01 to 0.1 μg/l according to the substance.     

Simultaneous determination of three organophosphorus pesticides in different food commodities by gas chromatography with mass spectrometry

A sensitive and selective gas chromatography with mass spectrometry method was developed for the simultaneous determination of three organophosphorus pesticides, namely, chlorpyrifos, malathion, and diazinon in three different food commodities (milk, apples, and drinking water) employing solid‐phase extraction for sample pretreatment. Pesticide extraction from different sample matrices was carried out on Chromabond C₁₈ cartridges using 3.0 mL of methanol and 3.0 mL of a mixture of dichloromethane/acetonitrile (1:1 v/v) as the eluting solvent. Analysis was carried out by gas chromatography coupled with mass spectrometry using selected‐ion monitoring mode. Good linear relationships were obtained in the range of 0.1–50 μg/L for chlorpyrifos, and 0.05–50 μg/L for both malathion and diazinon pesticides. Good repeatability and recoveries were obtained in the range of 78.54–86.73% for three pesticides under the optimized experimental conditions. The limit of detection ranged from 0.02 to 0.03 μg/L, and the limit of quantification ranged from 0.05 to 0.1 μg/L for all three pesticides. Finally, the developed method was successfully applied for the determination of three targeted pesticides in milk, apples, and drinking water samples each in triplicate. No pesticide was found in apple and milk samples, but chlorpyrifos was found in one drinking water sample below the quantification level.     

Pesticides and degradation products in groundwaters from a vineyard region: Optimization of a multiresidue method based on SPE and GC‐MS

A reliable multiresidue method based on solid phase extraction was developed using GC–MS to determine and quantify 34 pesticides, including herbicides, fungicides, insecticides, and some of their degradation products, in groundwater in a vineyard region of La Rioja (northern Spain). Different parameters were optimized and good recoveries (65–108% range) and precisions (12–19% range) were achieved with spiked water samples for a concentration of 0.1 μg/L. The experimental results showed an excellent linearity (r² > 0.99) over the 0.1–1.5 μg/L range. The detection limits of the proposed method were 1–37 ng/L for most of the compounds studied. The methodology has been successfully applied to the analysis of groundwater samples from vineyard areas in La Rioja and the presence of pesticides, especially fungicides and herbicides, at several concentration levels was revealed. Terbuthylazine, its metabolite desethyl‐terbuthylazine, and fluometuron were the pesticides most frequently detected in higher concentrations. Overall and taking into consideration the European Union maximum residue limit of pesticides in groundwater, 16 of the 34 compounds included in this study were detected in concentrations over that limit in at least one of the samples analyzed.     

Multiresidue determination of pesticides in juice by solid-phase extraction and gas chromatography-mass spectrometry

A multiresidue method based on solid-phase extraction was developed for the simultaneous determination of 50 pesticides in commercial juices. The extraction procedure was carried out in C₁₈ columns preconditioned with acetonitrile and water. The subsequent elution of pesticides was performed with a mixture of hexane-ethyl acetate (1:1, v/v) prior to the determination by gas chromatography with electron impact mass spectrometric detection in the selected ion monitoring mode (GC-MS-SIM), using one target and two qualifier ions. Standards were prepared spiking blank juice samples to counteract the observed matrix effect. Average recoveries for all the pesticides studied were higher than 91% with relative standard deviations lower than 9% in the concentration range of 0.02-0.1 μg/mL and the detection limits achieved ranged from 0.1 to 4.6 μg/L. The proposed method was applied to the analysis of these compounds in commercial juices and diazinon, ethion and procymidone were the pesticides encountered, although the levels found were very low.     

Simultaneous extraction and preconcentration of aniline,phenol, and naphthalene using magnetite–graphene oxide composites before gas chromatography determination

The coextraction of acidic and basic compounds from different mediums is a significant concept in sample preparation. In this work, simultaneous extraction of acidic, basic, and neutral analytes in a single step was carried out for the first time. This procedure employed the dispersive solid‐phase microextraction of analytes with magnetic graphene oxide (graphene oxide/Fe₃O₄) sorbent followed by gas chromatography with flame ionization detection. After the adsorption of analytes by vortexing and decantation of the supernatant with a magnet, the sorbent was eluted with acetonitrile/methanol (2:1) mixture. The parameters affecting the extraction efficiency were optimized and obtained as follows: sorbent amount 60 mg, desorption time 1 min, extraction time 5 min, pH of the sample 7, sample volume 20 mL, and elution solvent volume 0.3 mL. Under the optimum conditions, linear dynamic ranges were achieved in the range of 0.5–4, 0.25–4, and 0.25–2 μg/mL and limits of detection were 0.341, 0.110, and 0.167 μg/mL for aniline, phenol, and naphthalene, respectively. The relative standard deviations were in the range of 3.3–5.7% in eight repeated extractions. Finally, the applicability of the method was evaluated by the extraction and determination of analytes in stream water and drinking water samples and satisfactory results were obtained.     

Multiresidue analysis of polar pesticides in surface and drinking water by on-line enrichment and thermospray LC-MS

In the search for a fast and robust sample handling and preparation step to analyse various pesticides at trace levels in aqueous samples, an on-line trace enrichment has been combined with our thermospray LC-MS method [1] allowing both selective identification and a quantification down to the lower ng/L level. 51 polar pesticides were investigated by applying solid phase extraction to 50–100 ml aqueous samples using small cartridges filled with 40 mg adsorbent. Prior to their liquid chromatographic separation, the enriched analytes were eluted from the solid phase with the initial methanol/water gradient composition of the HPLC onto the analytical column using column switching techniques. A base-deactivated C₁₈ material and the two styrene-divinylbenzene copolymers PLRP-S and PRP-1 were tested for enrichment in combination with a C₈-bonded silica analytical column. The method developed was evaluated with respect to recoveries, precision, limits of detection and linearity. Furthermore, it was applied to various environmental samples. Apart from a few compounds of higher polarity, most of the pesticides show recoveries >60% (often >80%) with relative standard deviations between 1–15%. Overall method detection limits are in the range of 1–100 ng/L allowing, with one exception, a ready verification of the pesticide limit of 100 ng/L set in the EU drinking water guideline [2].     

On-line solid-phase extraction-thermal desorption-gas chromatography with ion trap detection tandem mass spectrometry for the analysis of microcontaminants in water

An improved set-up for solid-phase extraction with thermal desorption coupled on-line to gas chromatography (SPETD-GC) is presented. It includes a newly designed liner for a programmable temperature vaporizer (PTV) and an improved water elimination system. The SPETD procedure now includes a washing step with HPLC-grade water to prevent degradation of analytes due to interaction with remaining sample constituents. The system was used to analyze surface and tap water samples over a 4-month period. No decrease of chromatographic or trace-enrichment performance was observed, and a liner packed with Tenax GR could be used for at least 150 analyses. The SPETD module was coupled to GC with ion-trap detection for mass spectrometric (MS) and MS/MS detection. The linearity and repeatability of the procedure for several pesticides which were tested in the 0.5–10 μg/1 range were fully satisfactory (1 μg/1, RSD range 5–11%; n = 5). When using sample volumes of 0.1 ml only, detection limits were as low as 0. 1-0.2 μg/1. As an example, the confirmation and quantification of a suspected pesticide in a real-life sample using electron impact and positive chemical ionization in both the MS and MS/MS mode is shown.     

Multiresidue analysis of 36 pesticides in soil using a modified quick,easy, cheap,effective, rugged,and safe method by liquid chromatography with tandem quadruple linear ion trap mass spectrometry

A new method for simultaneous determination of 36 pesticides, including 15 organophosphorus, six carbamate, and some other pesticides in soil was developed by liquid chromatography with tandem quadruple linear ion trap mass spectrometry. The extraction and clean‐up steps were optimized based on the quick, easy, cheap, effective, rugged, and safe method. The data were acquired in multiple reaction monitoring mode combined with enhanced product ion to increase confidence of the analytical results. Validation experiments were performed in soil samples. The average recoveries of pesticides at four spiking levels (1, 5, 50, and 100 μg/kg) ranged from 63 to 126% with relative standard deviation below 20%. The limits of detection of pesticides were 0.04–0.8 μg/kg, and the limits of quantification were 0.1–2.6 μg/kg. The correlation coefficients (r²) were higher than 0.990 in the linearity range of 0.5–200 μg/L for most of the pesticides. The method allowed for the analysis of the target pesticides in the lower μg/kg concentration range. The optimized method was then applied to the test of real soil samples obtained from several areas in China, confirming the feasibility of the method.     

Screening of pesticide-contaminated soil by supercritical fluid extraction (SFE) and high-performance thin-layer chromatography with automated multiple development (HPTLC/AMD)

A method for screening of pesticide-contaminated soil was developed. The extraction is carried out by supercritical carbon dioxide (CO₂) with methanol as a modifier. The different components of the extracts are separated by high-performance thin-layer chromatography with automated multiple development (HPTLC/AMD) and evaluated densitometrically. The technique can be carried out without any previous clean-up step. Compared with other extraction techniques, SFE has the advantages of reducing the amount of co-extracted soil contents, which can seriously deteriorate the results. A 35-step development of the TLC-plate with gradient elution offers an application over a wide range of polarity. Migration data for 107 pesticides, recoveries and detection limits for 20 pesticides were determined.     

Determination of Triazines and N-Methylcarbamate Pesticides in Water by High-Performance Liquid Chromatography-Diode Array Detection

A rapid and selective method for the simultaneous determination of triazine herbicides (atrazine, its degradation product desethylatrazine, simazine, prometryn, terbutryn) and N-methylcarbamate insecticides (propoxur, carbaryl and methiocarb) in surface water has been developed. A 0.5 L of the water sample was preconcentrated by passage through a 1 g C₁₈ solid-phase extraction cartridge. The retained compounds were eluted with 5 mL of methanol from the cartridge. The pesticides were separated and quantified by reversed-phase high-performance liquid chromatography with UV diode-array detection. Analytical separation was performed using a concave gradient elution with acetonitrile and water on a C₁₈ column. Prometryn and terbutryn were determined at 240 nm; propoxur, methiocarb at 204 nm and the others at 220 nm. Recoveries varied from 85 to 102% over concentrations at 0.025 and 0.2 µg L^?1. The limits of detection for the compounds investigated are in the range of 0.005-0.012 µg L^?1.     

Application of Solid-Phase Microextraction for the Determination of Organonitrogen Pesticides in Aqueous Samples by Gas Chromatography with Nitrogen-Phosphorus Detector

A method based on solid-phase microextraction and gas chromatography nitrogen-phosphorus detector for the determination of common organonitrogen pesticides (ONPs) in aqueous samples was described. Three kinds of commercially available coated fused-silica fibres were compared: 100 µm PDMS, 85 µm PA, and 65 µm CW-DVB; 65 µm CW-DVB was the most sensitive fibre coating for the analytes' determination. The extraction time, the stirring, the content of salt, and the content of organic solvents were found to have a significant influence on extraction efficiency. The optimised conditions were 65 µm CW-DVB fibre, 40 min extraction time, with rapid stirring and concentration of NaCl was fixed at 0.25 g/mL. The linear range was 0.1-100 µg/L for most of the compounds. The limits of detection (LODs) ranged from 0.02 mg/L (for trifluralin, simazine, terbuthylazine, cyanazine, and pendimethalin) to 0.08 µg/L (for terbutryn) and RSD % of repeatability were for most of the compounds below 10%. Thus the maximum level set by the European Union for pesticides and drinking waters can be verified. The recovery of spiked water samples was compared and validated with the liquid-liquid extraction one. Environmental water samples were analysed and trifluraline was detected.     

Rapid clean-up of fat extracts for organophosphorus pesticide residue determination using C18 solid-phase extraction cartridges

Commercial solid-phase extraction (SPE) cartridges with C₁₈ bonded silica packings effectively cleaned up acetonitrile extracts of 3-g samples of fats and oils for determination of organophosphorus pesticide residues by gas chromatography with flame photometric detection. Cartridges from three different sources were tested and found to differ in lipid capacity and inertness (free silanol activity). Consequently, the amount of packing (i.e., number of cartridges) and/or the choice of eluent used were adjusted for each brand of cartridge to achieve optimum clean-up and analyte recovery. Seven pesticides with a wide range of polarity (acephate, azodrin, chlorpyrifos, diazinon, malathion, methamidophos and methyl parathion) were separated from coextracted lipids by elution with either acetonitrile or methanol, depending on the brand of cartridge used. Cartridges were regenerated by purging lipids with dichloromethane and were reused numerous times without apparent loss of effectiveness. Recoveries from vegetable oils and butterfat fortified with the seven compounds at levels of 0.05–0.87 μg g^?1 ranged from 80 to 103%. Practical limits of determination range from 0.01 to 0.08 μg g^?1, depending on analyte response.     

Multiresidue Analysis of Pesticides in Water from Rice Cultures by On-line Solid Phase Extraction Followed by LC-DAD

Abstract

An automated on-line solid phase extraction procedure followed by liquid chromatography with diode array detection was investigated for the determination of different classes of pesticides in water samples containing varied amount of humic substances. The different pesticides used were: carbendazin, carbofuran, atrazine, diuron, propanil, molinate, alachlor, parathion-ethyl, diazinon, trifluralin and the degradation products deisopropylatrazine and deethylatrazine. Humic substances extracted from a Brazilian sediment were used from 5 to 80 mg/l and their influence on recoveries was evaluated in neutral and acidic media. Recoveries higher than 70% were obtained for all the pesticides, from the preconcentration of 75 ml of aqueous sample fortified at 2 ng/ml using precolumns packed with PLRP-S. Good recoveries were obtained at neutral pH for most of the analytes up to 40 mg/l of humic acid. Only at 80 mg/l the recoveries were significantly affected, both at acidic and neutral pH. The method was applied to the determination of pesticides in river water spiked at 0.1 to 1 ng/ml. Detection limits obtained for water containing 10 mg/l of humic acid were between 0.05 and 0.3 ng/ml.     

Large-Volume Direct Injection for Determining Naphthalene Derivative Pesticides in Water Using a Restricted-Access Medium Column in RPLC-LC with Fluorescence Detection

A simple multidimensional system for direct injection of large volumes has been developed for the determination of three naphthalene-derivative pesticides [2-(1-naphthyl) acetamide (NAD), 1-naphthyl methylcarbamate (carbaryl) and 1-naphthol] in water using fluorescence detection. The capability of restricted-access medium (RAM), pre-columns for eliminating large interfering molecules, combined with an optimised, coupled-column separation procedure, large volume injection (LVI) and fluorescence detection, gave excellent sensitivity for target analytes. The maximum admissible concentration levels established by the European Union (EU) for individual pesticides and their related compounds in drinking water (0.1 μg L^?1) were easily reached. Detection limits were lower than, or equal to, 0.003 μg L^?1. Average recoveries ranged: 81–104% (n=3) with relative standard deviation (RSD) values: 2–7%. Application of the coupled-column liquid chromatography (LC-LC) method was by determining target analytes in ground water samples from five agricultural zones of Almería, (Spain) over three months.     

Vortex‐assisted liquid–liquid microextraction using a low‐toxicity solvent for the determination of five organophosphorus pesticides in water samples by high‐performance liquid chromatography

Vortex‐assisted liquid–liquid microextraction followed by high‐performance liquid chromatography with UV detection was applied to determine Isocarbophos, Parathion‐methyl, Triazophos, Phoxim and Chlorpyrifos‐methyl in water samples. 1‐Bromobutane was used as the extraction solvent, which has a higher density than water and low toxicity. Centrifugation and disperser solvent were not required in this microextraction procedure. The optimum extraction conditions for 15 mL water sample were: pH of the sample solution, 5; volume of the extraction solvent, 80 μL; vortex time, 2 min; salt addition, 0.5 g. Under the optimum conditions, enrichment factors ranging from 196 to 237 and limits of detection below 0.38 μg/L were obtained for the determination of target pesticides in water. Good linearities (r > 0.9992) were obtained within the range of 1–500 μg/L for all the compounds. The relative standard deviations were in the range of 1.62–2.86% and the recoveries of spiked samples ranged from 89.80 to 104.20%. The whole proposed methodology is simple, rapid, sensitive and environmentally friendly for determining traces of organophosphorus pesticides in the water samples.     

Simultaneous determination of thiamethoxam,clothianidin, and metazachlor residues in soil by ultrahigh performance liquid chromatography coupled to quadrupole time‐of‐flight mass spectrometry

A rapid pioneering method has been developed to simultaneously determine residues of three pesticides (thiamethoxam, clothianidin, and metazachlor) in soil by ultrahigh performance liquid chromatography coupled to a mass spectrometry detector (quadrupole time‐of‐flight). An efficient extraction procedure (90–105% average analyte recoveries) has also been proposed, involving solid–liquid extraction by a mixture of water and methanol (60:40, v/v), centrifugation, and concentration. A chromatographic analysis of the compounds was achieved in 5.5 min by means of a core–shell technology based column (Kinetex^® EVO C₁₈, 50 × 2.1 mm, 1.7 μm, 100 Å). The mobile phase (0.3 mL/min, gradient elution mode) consisted of 0.1% v/v formic acid in water and 0.1% v/v formic acid in acetonitrile. The method was fully validated in terms of selectivity, detection and quantification limits, matrix effect, linearity, trueness, and precision. Low limits of detection and quantification were obtained, ranging from 0.2 to 3.0 μg/kg, which are similar to those published in previous studies, while the absence of a significant matrix effect allowed quantification of the pesticides with standard calibration curves. The proposed method was applied for an analysis of pesticides in several soil samples from experimental fields dedicated to oilseed rape cultivars.     

Determination of Ibafloxacin,A New Quinolone Antibacterial,in Human and Dog Plasma and Urine by High Performance Liquid Chromatography

Abstract

A simple, selective and sensitive high performance liquid chromatographic method has been developed for quantifying plasma and urine ibafloxacin levels in humans and dogs.

Sample pretreatment is done by incorporation of an internal standard (IS) followed by a single step chloroform extraction. Samples are then chromatographed by reverse phase chromatography with UV detection. The lowest quantifiable concentration is 0.1 μg ibafloxacin/mL with a 1 mL sample. The assay was linear over the range of 0.1–50 μg/mL.     

Multi-residue determination of organophosphorus and organochlorine pesticides in environmental samples using solid-phase extraction with cigarette filter followed by gas chromatography-mass spectrometry

A solid‐phase extraction (SPE) method was developed to extract 14 pesticides simultaneously from environment samples using cigarette filter as the sorbent before gas chromatography‐mass spectrometry (GC‐MS) analysis. Parameters influencing the extraction efficiency, such as the sample loading flow rate, eluent and elution volume, were optimized. The optimum sample loading rate was 3 mL/min, and the retained compounds were eluted with 6 mL of eluent at 1 mL/min under vacuum. Good linearity was obtained for all the 14 pesticides (r²>0.99) from 0.1 to 20 μg/L for water and from 2 to 400 μg/kg for soil samples. The detection limits (signal‐to‐noise=3) of the proposed method ranged from 0.01 to 0.20 μg/L for water samples and from 0.42 to 6.95 μg/kg for soil samples. The developed method was successfully applied for determination of the analytes in real environmental samples, and the mean recoveries ranged from 76.4 to 103.7% for water samples and from 79.9 to 105.3% for soil samples with the precisions (relative standard deviation) between 2.0 and 13.6%.     

Headspace solid phase microextraction in the determination of pesticides in water samples from the Okavango Delta with gas chromatography-electron capture detection and time-of-flight mass spectrometry

Headspace solid phase microextraction (HS-SPME) was optimized for the analysis of pesticides with gas chromatography electron capture detection (GC-ECD) and high-resolution mass spectrometry. Factors influencing the extraction efficiency such as fiber type, extraction mode and temperature, effect of ionic strength, stirring and extraction time were evaluated. The lowest pesticide concentrations that could be detected in spiked aliquots after HS-SPME–GC-ECD ranged from 0.0005 to 0.0032 μg L^{− 1}. Consequently hexachlorobenzene, trans-chlordane, 4,4′-DDD and 4,4′-DDE were detected in water samples after HS-SPME at concentrations ranging from 2.4 to 61.4 μg L^{− 1} that are much higher than the 0.1 μg L^{− 1} maximum limit of individual organochlorine pesticides in drinking water set by the European Community Directive. The same samples were cleaned with ISOLUTE C₁₈ SPE sorbent with an optimal acetone/n-hexane (1:1 v/v) mixture for the elution of analytes. No pesticides were detected after SPE clean-up and pre-concentration. Precision for both methods was satisfactory with relative standard deviations less than 20%. This work demonstrated the superiority of HS-SPME as a sample clean-up and pre-concentration technique for pesticides in water samples as well as the need to identify and control point sources of pesticides.     

Determination of trace organophosphorus pesticides in water samples with TiO2 nanotubes cartridge prior to GC‐flame photometric detection

This article described a new method for the sensitive determination of organophosphorus pesticides in water samples using SPE in combination with GC‐flame photometric detection. In the procedure of method development, TiO₂ nanotubes were used as SPE adsorbents for the enrichment of organophosphorus pesticides from water samples. Several factors, such as eluent and its volume, sample pH, sample volume, sample flow rate, and concentration of humic acid, were optimized. Under the optimal conditions, the proposed method had good linear ranges as 0.1–40 μg/L for each of them, LOD of 0.11, 0.014, and 0.0025 μg/L, and LOQs of 0.37, 0.047, and 0.0083 μg/L for chlorpyrifos, phorate, and methyl parathion, respectively. The proposed method was validated with real environmental water samples and the spiked recoveries were over the range of 86.5–115.1%. All these results indicated that TiO₂ nanotubes, as a new SPE adsorbent, would be used widespread for the preconcentraiton and determination of environmental pollutants in the future.