Isothermal vapor–liquid equilibrium at 333.15 K and excess molar volumes at 298.15 K for the ternary system di-isopropyl ether + n-propyl alcohol + toluene and its binary subsystems

Isothermal vapor–liquid equilibrium data at 333.15 K are reported for the ternary system di-isopropyl ether (DIPE) + n-propyl alcohol + toluene and the binary subsystems DIPE + n-propyl alcohol, DIPE + toluene and n-propyl alcohol + toluene by using headspace gas chromatography. The excess molar volumes at 298.15 K for the same binary and ternary systems were also determined by directly measured densities. The experimental binary and ternary vapor–liquid equilibrium data were correlated with different G^E models and the excess molar volumes were correlated with the Redlich–Kister equation for the binary systems and the Cibulka equation for the ternary system, respectively.     

Investigation on isobaric vapor–liquid equilibrium for acetic acid + water + methyl ethyl ketone + isopropyl acetate

Isobaric vapor–liquid equilibrium (VLE) data for acetic acid + water, acetic acid + methyl ethyl ketone (MEK), MEK + isopropyl acetate, acetic acid + MEK + water and acetic acid + MEK + isopropyl acetate + water are measured at 101.33 kPa using a modified Rose cell. The nonideal behavior in vapor phase of binary systems measured in this work is analyzed through calculating fugacity coefficients since mixture containing acetic acid deviates from ideal behavior seriously in vapor phase due to the associating effect of acetic acid. Combined with Hayden–O’Connell (HOC) equation, the VLE data of the measured binary systems for acetic acid + water, acetic acid + MEK and MEK + isopropyl acetate are correlated by the NRTL and UNIQUAC models. The NRTL model parameters obtained from correlating data of binary system are used to predict the VLE data of the ternary and quaternary systems, and the predicted values obtained in this way agree well with the experimental values.     

Measurement and correlation of (liquid + liquid) equilibrium of the azeotrope (cyclohexane + 2-butanone) with different ionic liquids at T = 298.15 K

Experimental densities, speeds of sound, and refractive indices of the binary mixtures of 2-butanone with cyclohexane and OMIM PF₆ (1-methyl-3-octylimidazolium hexafluorophosphate) were determined from T = (293.15 to 303.15) K, since they are necessary to determine the (liquid + liquid) equilibrium. Excess molar volumes, changes of refractive index on mixing, and deviations in isentropic compressibility for the above systems were calculated. Experimental (liquid + liquid) equilibrium of the ternary mixtures {cyclohexane + 2-butanone + 1-hexyl-3-methylimidazolium hexafluorophosphate (HMIM PF₆)} and (cyclohexane + 2-butanone + OMIM PF₆) were carried out to assess the suitability of HMIM PF₆ and OMIM PF₆ as azeotrope breaker of the mixture cyclohexane and 2-butanone. Selectivity and distribution ratio values, derived from the tie lines data, were presented in order to analyze the best separation solvent in a liquid extraction process. Experimental (liquid + liquid) equilibrium data were compared with the correlated values obtained by means of the NRTL and UNIQUAC models.     

Volumetric study of (2-methoxyethanol + tetrahydrofuran + cyclohexane) at T=298.15 K

The excess molar volumes V_m^E at T=298.15 have been determined in the whole composition domain for (2-methoxyethanol + tetrahydrofuran + cyclohexane) and for the parent binary mixtures. Data on V_m^E are also reported for (2-ethoxyethanol + cyclohexane). All binaries showed positive V_m^E values, small for (methoxyethanol + tetrahydrofuran) and large for the other ones. The ternary V_m^E surface is always positive and exhibits a smooth trend with a maximum corresponding to the binary (2-methoxyethanol + cyclohexane). The capabilities of various models of either predicting or reproducing the ternary data have been compared. The behaviour of V_m^E and of the excess apparent molar volume of the components is discussed in both binary and ternary mixtures. The results suggest that hydrogen bonding decreases with alcohol dilution and increases with the tetrahydrofuran content in the ternary solutions.     

Determination and correlation of liquid–liquid equilibria for the (water + carboxylic acid + dimethyl maleate) ternary systems at T = 298.2 K

(Liquid–liquid) equilibrium (LLE) data for the ternary systems of {water + carboxylic acid (formic, acetic, propionic or butyric acid) + dimethyl maleate} were measured at T = 298.2 K and atmospheric pressure. Selectivity values for solvent separation efficiency were derived from the tie-line data. A comparison of the extracting capabilities of the solvent was made with respect to distribution coefficients, separation factors, and solvent-free selectivity bases. The reliability of the data was ascertained from Othmer–Tobias plots. The experimental data were correlated using the UNIQUAC and NRTL (α = 0.2) equations, and the binary interaction parameters were reported. The phase diagrams for the ternary mixtures including both the experimental and calculated tie-lines were presented.     

Temperature dependence on mutual solubility of binary (methanol + limonene) mixture and (liquid + liquid) equilibria of ternary (methanol + ethanol + limonene) mixture

Mutual solubility data of the binary (methanol + limonene) mixture at the temperatures ranging from 288.15 K close to upper critical solution temperature, and ternary (liquid + liquid) equilibrium (tie-lines) of the (methanol + ethanol + limonene) mixture at the temperatures (288.15, 298.15, and 308.15) K have been obtained. The experimental results have been represented accurately in terms of the extended and modified UNIQUAC models with binary parameters, compared with the UNIQUAC model. The temperature dependence of binary and ternary (liquid + liquid) equilibrium for the binary (methanol + limonene) and ternary (methanol + ethanol + limonene) mixtures could be calculated successfully using the extended and modified UNIQUAC model.     

Isothermal vapor–liquid equilibria for binary mixtures of benzene, toluene, m-xylene, and N-methylformamide at 333.15 K and 353.15 K

Isothermal vapor–liquid equilibrium (VLE) at 333.15 K and 353.15 K for four binary mixtures of benzene + toluene, benzene + N-methylformamide, toluene + m-xylene and toluene + N-methylformamide have been obtained at pressures ranged from 0 kPa to 101.3 kPa. The NRTL, UNIQUAC and Wilson activity coefficient models have been employed to correlate experimental pressures and liquid mole fractions. The non-ideal behavior of the vapor phase has been considered by using the Soave–Redlich–Kwong equation of state in calculating the vapor mole fraction. Liquid and vapor densities were also measured by using two vibrating tube densitometers. The P–x–y diagram and the activity coefficient indicate that two mixtures of benzene + toluene and toluene + m-xylene were close to the ideal solution. However, two mixtures containing N-methylformamide present a large positive deviation from the ideal solution. The excess Gibbs energy in the benzene + toluene mixture is negative indicates that it is an exothermic system.     

Liquid–liquid equilibria for pseudo-ternary systems: (Sulfolane + 2-ethoxyethanol) + octane + toluene at 293.15 K

Liquid–liquid equilibrium data, both binodal and tie lines are presented for the pseudo-ternary systems: {(sulfolane + 2-ethoxyethano) (1) + octane (2) + toluene (3)} at 293.15 K. The experimental liquid–liquid equilibrium data have been correlated using NRTL and UNIQUAC models, and the binary interaction parameters of these components have been presented. The correlated tie lines have been compared with the experimental data. The comparisons indicate that both NRTL and UNIQUAC models satisfactorily correlated the equilibrium compositions. The tie-line data of the studied systems also were correlated using the Hand method.     

(Liquid + liquid) equilibria for mixtures of (ethylene glycol + benzene + cyclohexane) at temperatures (298.15, 308.15, and 318.15) K

Experimental (liquid + liquid) equilibrium (LLE) data for a ternary system containing (ethylene glycol + benzene + cyclohexane) were determined at temperatures (298.15, 308.15, and 318.15) K and at atmospheric pressure. The experimental distribution coefficients and selectivity factors are presented to evaluate the efficiency of the solvent for extraction of benzene from cyclohexane. The effect of temperature in extraction of benzene from the (benzene + cyclohexane) mixture indicated that at lower temperatures the selectivity (S) is higher, but the distribution coefficient (K) is rather lower. The LLE results for the system studied were used to obtain binary interaction parameters in the UNIQUAC and NRTL models by minimizing the root mean square deviations (RMSD) between the experimental results and calculated results. Using the interaction parameters obtained, the phase equilibria in the systems were calculated and plotted. The NRTL model fits the (liquid + liquid) equilibrium data of the mixture studied slightly better. The root mean square deviations (RMSDs) obtained comparing calculated and experimental two-phase compositions are 0.92% for the NRTL model and 0.95% for the UNIQUAC model.     

Vapor–liquid equilibrium,densities, and interfacial tensions for the system ethyl 1,1-dimethylethyl ether (ETBE) + propan-1-ol

Isobaric vapor–liquid equilibrium data at 50, 75, and 94 kPa have been determined for the binary system ETBE + propan-1-ol, in the temperature range 325–368 K. The measurements were made in a vapor–liquid equilibrium still with circulation of both phases. Mixing volumes have been also determined from density measurements at 298.15 K and 101.3 kPa and, at the same temperature and pressure, the dependence of interfacial tension on concentration has been measured using the pendant drop technique. According to experimental results, the mixture presents positive deviation from ideal behavior and azeotropy is present at 75 and 94 kPa. No azeotrope was detected at 50 kPa. The mixing volumes of the system are negative over the whole mole fraction range, and the interfacial tensions exhibit negative deviation from the linear behavior. The activity coefficients and boiling points of the solutions were well correlated with the mole fraction using the Wohl, Wilson, NRTL, UNIQUAC equations. Excess volume data and interfacial tensions were correlated using the Redlich–Kister model.     

Isobaric vapor–liquid equilibria for mixtures of acetone,ethanol, and 2,2,4-trimethylpentane at 101.3 kPa

Isobaric vapor–liquid equilibrium (VLE) data were determined at the pressure of 101.3 kPa for binary and ternary systems composed of acetone, ethanol, and 2,2,4-trimethylpentane (isooctane). Minimum boiling azeotropes were found in the acetone + 2,2,4-trimethylpentane and ethanol + 2,2,4-trimethylpentane systems. Azeotropic behavior was not found for the ternary system. Thermodynamic consistency tests were performed for all VLE data. The activity coefficients of the binary mixtures were satisfactorily correlated as function of the mole fraction using the Wilson, NRTL, and UNIQUAC models. The models with their best-fitted parameters were used to predict the ternary vapor–liquid equilibrium. The Wilson model appears to yield the best prediction in boiling temperatures.     

High-pressure phase behaviour of the binary system {CO2 + cis-decalin} from (292.75 to 373.75) K

The phase behaviour of the {CO₂ (1) + cis-decalin (2)} binary system has been experimentally studied at temperatures ranging from (292.75 to 373.75) K. Saturation pressures, ranging from (15.9 to 490.5) bar, were obtained using a variable volume high-pressure cell by visual observation of phase transitions at constant overall composition. For this system, no literature data are available and the results obtained in this study reveal the occurrence of vapor–liquid, liquid–liquid, and vapor–liquid–liquid phase transitions in the investigated temperature range. A total of 133 experimental points are reported including bubble points, dew points, liquid–liquid phase equilibria, and coordinates of the three-phase line. The experimental data can be reasonably predicted by the PPR78 model in which the temperature-dependent binary interaction parameter is calculated by a group contribution method.     

(Liquid + liquid) equilibria in ternary aqueous mixtures of phosphoric acid with organic solvents at T = 298.2 K

(Liquid + liquid) equilibrium (LLE) data for the ternary mixtures of {water (1) + phosphoric acid (2) + organic solvents (3)} were determined at T = 298.2 K and atmospheric pressure. The organic solvents were cyclohexane, 2-methyl-2-butanol (tert-amyl alcohol), and isobutyl acetate. All the investigated systems exhibit Type-1 behaviour of LLE. The immiscibility region was found to be larger for the (water + phosphoric acid + cyclohexane) ternary system. The experimental LLE results were correlated with the NRTL model, and the binary interaction parameters were obtained. The reliability of the experimental tie-line results was tested through the Othmer–Tobias and Bachman correlation equations. Distribution coefficients and separation factors were evaluated over the immiscibility regions and a comparison of the extracting capabilities of the solvents was made with respect to these factors. The experimental results indicate the superiority of cyclohexane as the preferred solvent for the extraction of phosphoric acid from its aqueous solutions.     

Isobaric vapor–liquid and vapor–liquid–liquid equilibrium data for the system water + ethanol + cyclohexane

Isobaric vapor–liquid (VLE) and vapor–liquid–liquid equilibria (VLLE) were measured for the ternary system water + ethanol + cyclohexane at 101.3 kPa. The experimental determination was carried out in a dynamic equilibrium still with circulation of both the vapor and liquid phases, equipped with an ultrasonic homogenizer. The experimental data demonstrated the existence of a ternary heterogeneous azeotrope at 335.6 K with a composition of 0.188, 0.292, 0.520 mole fraction of water, ethanol and cyclohexane, respectively. The experimental data were compared with those obtained using UNIFAC and NRTL models with parameters taken from literature.     

Isobaric (vapor + liquid) equilibria of the binary system maleic anhydride and diethyl phthalate at p = (2.67, 5.33, and 8.00) kPa

Saturated vapor pressures of pure diethyl phthalate were measured with the ebulliometer. And isobaric (vapor + liquid) equilibrium data for the binary system (maleic anhydride + diethyl phthalate) at p = (2.67, 5.33, and 8.00) kPa were determined using the ebulliometric method. The parameters of the NRTL model for the binary system were obtained by calculating equilibrium compositions of the liquid and vapor phase with the experimental equilibrium temperatures, pressures and feed compositions. Moreover, (vapor + liquid) equilibrium data for the binary system were predicted by use of the UNIFAC model. Predicted results were compared with those from the ebulliometric method, and showed good agreement.     

Evaluation of (vapor + liquid) equilibria for the binary systems (1-octanol + cyclohexane) and (1-octanol + n-hexane), at low alcohol compositions

Isobaric (vapor + liquid) equilibrium at p = 101.32 kPa of pressure has been determined for the systems (1-octanol + cyclohexane) and (1-octanol + n-hexane), at low alcohol mole fractions. These data were satisfactorily correlated, using ASPEN PLUS^® commercial software, with Wilson, NRTL, and UNIQUAC activity coefficient models to obtain the binary interaction parameters of both mixtures. Also, UNIFAC group contribution method was employed to predict the equilibrium of both mixtures. With regression values an accurate knowledge of (vapor + liquid) equilibrium for both mixtures can be reached in a range of 1-octanol mole fractions less than 0.1. UNIFAC method provides acceptable results for (1-octanol + n-hexane) system but not for (1-octanol + cyclohexane) system.     

Isothermal vapor–liquid equilibrium at 303.15 K and excess molar volumes at 298.15 K for the ternary system of propyl vinyl ether + 1-propanol + 2,2,4-trimethyl-pentane and its binary sub-systems

Isothermal vapor–liquid equilibrium data determined by the static method at 303.15 K are reported for the binary systems propyl vinyl ether + 1-propanol, 1-propanol + 2,2,4-trimethylpentane and propyl vinyl ether + 2,2,4-trimethylpentane and also for the ternary system propyl vinyl ether + 1-propanol + 2,2,4-trimethyl-pentane. Additionally, new excess volume data are reported for the same systems at 298.15 K. The experimental binary and ternary vapor–liquid equilibrium data were correlated with different G^E models and excess molar volume data were correlated with the Redlich–Kister equation for the binary systems and the Cibulka equation for the ternary system, respectively.     

Experimental and predicted excess molar enthalpies for 1,4-dioxane + octane + cyclohexane at 303.15 K

Excess molar enthalpies for the ternary system 1,4-dioxane (1) + n-octane (2) + cyclohexane (3) and for the three constituent binary systems have been measured by a Calvet microcalorimeter at 303.15 K and ambient pressure. The experimental binary results were fitted by the Redlich–Kister equation. The excess molar enthalpies of the ternary system were correlated using the Cibulka equation. The DISQUAC group contribution model was applied to predict the excess molar enthalpy for this mixture.     

Experimental investigation of the vapour–liquid equilibrium of binary and ternary mixtures containing dibutyl ether (DBE), cyclohexane and toluene at 313.15 K

New vapour–liquid equilibrium data for binary and ternary mixtures formed by dibutyl ether (DBE), toluene and cyclohexane at 313.15 K have been measured. A static method using an isothermal total pressure cell (Van Ness’ technique) has been employed. The systems studied presented a slight deviation from ideal behaviour. None of them show azeotrope. The VLE data have been satisfactorily correlated with the equations of Margules, Wilson, NRTL and UNIQUAC for binaries and Wohl expansion, Wilson, NRTL and UNIQUAC for the ternary system. Predictions with UNIFAC group contribution methods are included.     

Phase equilibria in the ternary system isobutyl alcohol + isobutyl acetate + 1-hexanol and the binary systems isobutyl alcohol + 1-hexanol,isobutyl acetate + 1-hexanol at 101.3 kPa

Consistent vapor–liquid equilibrium (VLE) data at 101.3 kPa have been determined for the ternary system isobutyl alcohol (IBA) + isobutyl acetate (IBAc) + 1-hexanol and two constituent binary systems: IBA + 1-hexanol and IBAc + 1-hexanol. The IBA + 1-hexanol system exhibits no deviation from ideal behaviour and IBAc + 1-hexanol system show lightly positive deviation from Raoult's law. The activity coefficients of the solutions were correlated with its composition by the Wilson, NRTL, UNIQUAC models. The ternary system is well predicted from binary interaction parameters. 1-Hexanol eliminates the IBA–IBAc binary azeotrope. However, the change of phase equilibria behaviour is small therefore this solvent is not an effective agent for that azeotrope mixture separation. In fact, the mean relative volatility on a solvent free basis is 1.28 (close to unity).