Energy gaps,charge distribution and optical properties of AlxIn1−xSb ternary alloys

The electronic and optical properties of Al_xIn_1−xSb ternary alloys have been investigated using a pseudopotential approach within the virtual crystal approximation. The effect of alloy disorder on the studied properties has been examined and found to be weak. The extent of the direct-to-indirect band gap transition is found to occur at x = 0.73. Our results agree well with those reported in the literature. Trends in bonding and ionicity are discussed by means of the electron charge distribution. The present study may be a useful information for mid-infrared inter band cascade lasers applications and other antimonide device structures.     

Effects of a Cu-contained compound on the microstructures and thermoelectric properties of Zn–Sb based alloys

Zn–Sb based alloys with Cu₂Sb addition were prepared using spark plasma sintering technique and the effects of a Cu-contained intermetallic phase on the microstructures and thermoelectric properties were examined. Rietveld refinement reveals that there are many phases in the alloys, which involve β-Zn₄Sb₃, a major phase ZnSb, a small amount of an intermetallic compound Cu₅Zn₈ and unidentified impurity phases, the quantities of ZnSb and Cu₅Zn₈ increase from 67.3 wt.% to 91.8 wt.% and 0–4.3 wt.% with Cu₂Sb additive increasing, respectively. The ZnSb plays a fundamental role in controlling the thermoelectric properties, and Cu₅Zn₈ is of great significance to optimize the transport properties. The maximum thermoelectric figure of merit ZT of 0.72 is obtained for the alloy (Cu₂Sb)_0.05–(Zn₄Sb₃)_0.95 at 654 K, which is 0.25 higher than that of undoped β-Zn₄Sb₃ at the same conditions. Therefore, we conclude that a proper addition of Cu₂Sb can contribute to the improvement of thermoelectric properties of Zn–Sb based alloys.     

Influence of Sr substitution on thermoelectric properties of La1−xSrxFeO3 ceramics

Perovskite La_1−xSr_xFeO₃ (0.10 ⩽ x ⩽ 0.20) ceramics have been synthesized by the conventional solid-state reaction technique. Their electrical resistivity, Seebeck coefficient and thermal conductivity have been measured. It has been found that the increase of Sr content reduces significantly both the electrical resistivity and the Seebeck coefficient, but slightly increases the high-temperature thermal conductivity. An adiabatic hopping conduction mechanism of small polaron is suggested from the analysis of the temperature dependence of the electrical resistivity. Seebeck coefficients decrease with increasing temperature, and saturate at temperature above 573 K. The saturated value of Seebeck coefficient decreases with increasing of Sr contents, from 200 μV/K for x = 0.10 to 100 μV/K for x = 0.20. All samples exhibit lower thermal conductivity with values around 2.6 W/m K. The highest dimensionless figure of merit is 0.031 at temperature 973 K in La_0.88Sr_0.12FeO₃.     

First-principle calculations of the fundamental properties of CuBrxI1−x ternary alloy

Ab initio full-potential linearised augmented plane wave (FP-LAPW) method within density functional theory is applied to study the effect of composition on the structural, electronic and thermodynamic properties of CuBr_xI_1?x ternary alloy. The structural properties at equilibrium are investigated by using the new form of generalised gradient approximations that are based on the optimisation of total energy. For band structure calculations, both Engel–Vosko and modified Becke–Johnson of the exchange-correlation energy and potential, respectively, are used. Deviation of the lattice constants from Vegard's law and the bulk modulus from linear concentration dependence are observed. The microscopic origins of the gap bowing were explained by using the approach of Zunger and co-workers. On the other hand, the thermodynamic stability of this alloy was investigated by calculating the excess enthalpy of mixing ?Hm as well as the phase diagram by calculating the critical temperatures. A numerical first-principle calculations of the elastic constants as function of pressure is used to calculate C₁₁, C₁₂ and C₄₄.     

Effect of Ni deficit on the electronic structure and magnetic properties of PrNi2−xSb2

The influence of a Ni deficit in the nickel sublattice on the electronic and magnetic properties of PrNi_2−xSb₂ compound is investigated. The band structure is calculated using the LMTO method for x=0, 0.50, 1.0 and 1.5. At T=0 K the compound is antiferromagnetic with a magnetic moment on Pr close to 2.0 μ_B.     

Effects of Cd concentration on structure and optical properties of the ternary Zn1−xCdxO nanopowder prepared by sol–gel method

Zn_1−xCd_xO nanocrystalline powder with different Cd contents (0≤x≤1) has been prepared by new facile sol–gel route. The crystal structure and optical properties were investigated by X-ray diffraction patterns, Transmission electron microscope, X-ray photoelectron spectroscopy, Photoluminescence. As x varied from x=0 to 0.25, the Zn_1−xCd_xO nanopowder exhibits a hexagonal wurtzite structure of pure ZnO without any significant formation of a separated CdO phase. For the samples with 0.5≤x≤0.85, the Zn_1−xCd_xO nanopowder exhibits the coexistence of hexagonal ZnO and cubic CdO phase, meanwhile, the content of ZnO phase decreases while that of CdO increases with increasing the Cd content x. The ultra-violet near-band-edge emission of the Zn_1−xCd_xO nanopowder was monotonously red-shifted from 389 nm (x=0) to 406 nm (x=0.25) due to the direct modulation of band gap caused by Cd substitution.     

Impact of iron composition on the calculated electronic and magnetic properties of Fe3−xNixSi

ABSTRACT

The structural, electronic and magnetic properties of Fe_3?xNi_xSi alloys with variable iron composition (0?≤?x?≤?1) have been investigated within by using Projector augmented wave (PAW) method. The exchange–correlation potential was treated with the generalised gradient approximation (GGA) for the calculation of the structural properties and for the computation of the electronic and magnetic properties in order to treat the d states. These alloys crystallize in cubic Heusler structures; The Fe₃Si and Fe₂NiSi have a regular structure DO₃ and L2₁ respectively. To describe the experimental proprieties we use the on-site Coulomb interactions of U_eff(Ni)?=?3.1?eV and U_eff(Fe)?=?3.4?eV. A good agreement between calculated and experimental magnetic moments is found for the cubic Heusler phases without the addition of Hubbard-model. The obtained results of the density of states and the spin-polarized band structure show that the Fe₂NiSi alloy has half-metallic property. Through the obtained values of the total spin magnetic moment, we conclude that in general, the Fe₂NiSi alloy is half-metallic ferromagnet material whereas the Fe₃Si alloy has a metallic nature.     

Electrical conduction and thermoelectric properties of perovskite-type BaBi1−xSbxO3

To elucidate the thermoelectric properties at high temperatures, the electrical conductivity and Seebeck coefficient were measured at temperatures between 423 K and 973 K for perovskite-type ceramics of BaBi_1?xSb_xO₃ solid solutions with x=0.0–0.5. All the ceramics exhibit p-type semiconducting behaviors and electrical conduction is attributed to hopping of small polaronic holes localized on the pentavalent cations. Substitution of Bi with Sb causes the electrical conductivity σ and cell volume to decrease, but the Seebeck coefficient S to increase, suggesting that the Sb atoms are doped as Sb⁵⁺ and replace Bi⁵⁺, reducing 6s holes conduction from Bi⁵⁺(6s⁰) to Bi³⁺ (6s²). The thermoelectric power factor S ²σ has values of 6×10^?8–3×10^?5 W m^?1 K^?2 in the measured temperature range, and is maximized for an Sb-undoped BaBiO_3?δ, but decreases upon Sb doping due to the decreased σ values.     

First-principles calculations of structural,electronic and thermal properties of Zn1−x Mg x S ternary alloys

Structural, electronic and thermal properties of Zn_1?x Mg _x S ternary alloys are studied by using the full potential-linearized augmented plane wave method (FP-LAPW) within the density functional theory (DFT). The Wu-Cohen generalized gradient approximation (WC-GGA) is used in this approach for the exchangecorrelation potential. Moreover, the modified Becke-Johnson approximation (mBJ) is adopted for band structure calculations. The dependence of the lattice constant, bulk modulus and band gap on the composition x showed that the first exhibits a small deviation from the Vegard’s law, whereas, a marginal deviation of the second from linear concentration dependence (LCD). The bowing of the fundamental gap versus composition predicted by our calculations agrees well with the available theoretical data. The microscopic origins of the gap bowing are explained by using the approach of Zunger and co-workers. Thermal effects on some macroscopic properties of Zn_1?x Mg _x S alloys are also investigated using the quasi-harmonic Debye model, in which the phononic effects are considered. As, this is the first quantitative theoretical prediction of the thermal properties of Zn_1?x Mg _x S alloys, no other calculated results and furthermore no experimental studies are available for comparison.     

Structural and optical properties of InxGa1−xAs strained layers grown on GaAs substrates by MOVPE

In_xGa_1−xAs/GaAs pseudomorphic structures were grown by metalorganic vapor phase epitaxy. Reciprocal space mapping were recorded in the vicinity of (0 0 4) and (1 1 5) nodes using high resolution X-ray diffraction (HRXRD) in order to determine strain tensor components, indium compositions and thicknesses of alloys. Near-infrared photoluminescence (PL) was performed at 10 K. The impact of strain on PL response was revealed by peak energy positions and line width. In addition, valence-band splitting (VBS) and the shift of the heavy-hole were measured. Besides, photoreflectance (PR) at room temperature was useful to establish experimentally the dependence of VBS and band energy shifts (E₀ and E₀+∆₀) on elastic strain due to lattice mismatches. Other parameters such as the internal electric-field and the electro-optical energy were determined from Franz–Keldysh oscillations analysis. Good correlation between the results obtained from all investigated techniques and theoretical predictions was confirmed.     

Effects of disorder in Mg1−xTaxB2 alloys using the coherent-potential approximation

Using the Korringa–Kohn–Rostoker coherent-potential approximation in the atomic-sphere approximation (KKR-ASA CPA) method for taking into account the effects of disorder, Gaspari–Gyorffy formalism for calculating the electron–phonon coupling constant λ, and Allen–Dynes equation for calculating T_c, we have studied the variation of T_c in Mg_1−xTa_xB₂ alloys as a function of Ta concentration. Our results show that the T_c decreases with the addition of Ta for up to 40 at.% and remains essentially zero from 60 to 80 at.% of Ta. We also find TaB₂ to be superconducting, albeit at a lower temperature. Our analysis shows that the variation in T_c in Mg_1−xTa_xB₂ is mostly dictated by the changes in the B p density of states associated with the addition of Ta.     

Theoretical investigations of the structural,electronic and optical properties of Hg1−xCdxTe alloys

The structural, electronic and optical properties of mercury cadmium telluride (Hg_1?xCd_xTe; x = 0.0, 0.25, 0.5, 0.75) alloys are studied using density functional theory within full-potential linearized augmented plane wave method. We used the local density approximation (LDA), generalized gradient approximation (GGA), hybrid potentials, the modified Becke–Johnson (LDA/GGA)-mjb and Hubbard-corrected functionals (GGA/LDA + U), for the exchange-correlation potential (E_ex). We found that LDA functional predicts better lattice constants than GGA functional, whereas, both functionals fail to predict the correct electronic structure. However, the hybrid functionals were more successful. For the case of HgTe binary alloy, the GGA + U functional predicted a semi-metallic behaviour with an inverted band gap of ?0.539 eV, which is closest to the experimental value (?0.30 eV). Ternary alloys, however, are found to be semiconductors with direct band gaps. For the x = 0.25 and 0.50, the best band gaps are found to be 0.39 and 0.81 eV using LDA-mbj functional, whereas, the GGA-mbj functional predicted the best band gap of 1.09 eV for Hg_0.25Cd_0.75Te alloy, which is in a very good agreement with the experimental value (1.061 eV). The optical properties of the alloys are obtained by calculating the dielectric function ?(ω). The peaks of the optical dielectric functions are consistent with the electronic gap energies of the alloys.     

First-principles studies of the structural,electronic and optical properties of Zn1−xCdxS and ZnS1−ySey alloys

Using the density functional theory calculations, we studied the structural, electronic and optical properties of zincblende Zn_1?xCd_xS and ZnS_1?ySe_y alloys. Calculated structures and band gaps of these alloys are in good agreement with available experimental and other theoretical values. Present results show that the prominent peaks of the dielectric functions and absorption coefficients have a slight red shift and the amplitudes become larger with the increasing concentration of Cd and Se. Moreover, present findings predict that Zn_1?xCd_xS and ZnS_1?ySe_y alloys are promising for solar cells and photoconductor and electroluminescent devices due to their high absorption of solar radiations and photoconductivity in the energy region from visible light to ultraviolet.     

Effects of the dielectric discontinuity on the photodetachment of H− ion

Using the closed orbit theory, we studied the effects of dielectric discontinuity on the photodetachment of H^? ions. The photodetachment cross-section of H^? in a medium with dielectric discontinuity was derived and calculated. The results have shown that the relative dielectric constants of the medium have a significant influence on the photodetachment of H^?. If H^? is kept in a medium with a relative small dielectric constant, the photodetachment cross-section of H^? becomes oscillating only in a small region above the ionization threshold. However, if H^? is kept in a medium with a relative large dielectric constant, the oscillation in the photodetachment cross-section becomes much stronger. Besides, the distance between H^? and the dielectric dividing interface also influences the photodetachment of H^?. For a given dielectric medium, the oscillation in the cross-section decreased with increasing distance between H^? and the dielectric dividing interface. Therefore, we can control the photodetachment of a negative ion by changing the dielectric constant and the ion–interface distance. This study provides a new understanding of the photodetachment process of negative ions in the presence of a dielectric medium.     

Investigation of the effect of annealing on the magnetic properties of Sn1−xEuxTe single crystals

A study of the effect of annealing on the magnetic properties of single crystals Sn_1−xEu_xTe is reported. The width of the electron paramagnetic resonance line of the crystal is found to decrease upon annealing but its g-value of 1.991 is nearly unaffected. Magnetization results indicate that the pair exchange interaction is weakly antiferromagnetic with a value of −0.67 K for the non-annealed sample and −0.29 K after annealed sample. Susceptibility measurements performed as a function of temperature also indicate the presence of EuTe clusters in the as-grown Sn_1−xEu_xTe crystals. Therefore it was deduced that the Eu²⁺ ions tend to form clusters, particularly pairs, in the as-grown crystal and these clusters disappear after annealing, as the Eu²⁺ ions occupy isolated sites in the SnTe host lattice.     

Optical properties of ternary ZnS x Se1−x polycrystalline thin films

Ternary ZnS_xSe_1–x polycrystalline thin films were prepared by evaporation in vacuum of 10^–5 Torr. The molecular fractionx varied in the region ox1. The optical constants (the refractive indexn, the absorption indexk, and the absorption coefficient) were determined in the wavelength range 300–1600nm. A plot representing ₂=f(hv) shows that the ZnS_xSe_1–x polycrystalline thin films of different compositions have two direct transitions corresponding to the energy gapsE andE+. The variation in eitherE orE+ withx indicates that this system belongs to the amalgamation type. Such variation follows a quadratic equation. The bowing parameter was found to be 0.456 eV, roughly equal to the calculated value 0.60 eV using the empirical pseudopotential method based on the virtual-crystal approximation, in which the disorder effect has not been taken into account.     

Structural and electronic properties of GaN x As1−x alloys

The structural and electronic properties of cubic GaN _x As_1−x with N-concentration varying between 0.0 and 1.0 with step of 0.25 were investigated using the full potential–linearized augmented plane wave (FP-LAPW) method. We have used the local density approximation (LDA) and the generalized gradient approximation (GGA) for the exchange and correlation potential. In addition the Engel-Vosko generalized gradient approximation (EVGGA) was used for the band-structure calculations. The structural properties of the binary and ternary alloys were investigated. The electronic band structure, total and partial density of states as well as the electron charge density were determined for both the binary and their related ternary alloys. The energy gap of the alloys decreases when we move from x=0.0 to 0.25; then it increases by a factor of about 1.8 when we move from 0.25 to 0.5, 0.75 and 1.0 using EVGGA. For both LDA and GGA moving from x=0.0 to 0.25 causes the band gap to close, showing the metallic nature of the GaN_0.25As_0.75 alloy. When the composition of N moves through x=0.25, 0.5, 0.75 and 1, the band gap increases.     

Structural,optical and transport properties of PbxHg1−xTe alloys

It has been shown that the plasma frequency for polycrystalline PbxHg_1−xTe samples with x = 0.93 and x = 0.85 decreases unexpectedly compared with that of pure high-quality PbTe. At the same time the free-carrier concentration is lower than for the high-quality single-crystal samples of pure PbTe treated in the literature.