Preparation of nanocrystalline TiO<Subscript>2</Subscript> powders for photocatalytic oxidation of phenol

Nanocrystalline TiO₂ powders in the anatase, rutile, and mixed phases prepared by hydrolysis of TiCl₄ solution were of ultrafine size (<7.2 nm) with high specific surface areas in the range 167 to 388 m²/g. In the photocatalytic degradation of phenol as model reaction, the photocatalytic properties of TiO₂ nanoparticles were evaluated by use of UV–vis absorption spectroscopy and total organic carbon (TOC) content. The synthetic mixed-phase TiO₂ powder calcined at 400 °C had higher activity than pure anatase or rutile; it degraded more than 90% phenol to CO₂ (evaluated by TOC) after irradiation with near UV light for 90 min at a catalyst loading of 0.4 g/L. The TOC results indicated that rutile TiO₂ crystallites of particle size 7.2 nm resulted in much better photocatalytic performance than particles of larger size. This result suggested that some intermediates, not determined by UV–vis absorption spectroscopy, existed in the solution after the photocatalytic process over the rutile TiO₂ photocatalysts of larger crystallite size.     

Hydrothermal synthesis,structure and photocatalytic property of nano-TiO<Subscript>2</Subscript>-MnO<Subscript>2</Subscript>

TiCl₄ and MnSO₄· H₂O as raw materials are hydrolyzed stiochiometrically, following the intermediate of oxide hydrating reacts at 150°C, 0.5 MPa in high-pressure reactor, after filtering, washing and drying, nanometric TiO₂-MnO₂ (Ti_1-X Mn _X O₂) is prepared. The effects of the reaction temperature and time on nanometric TiO₂-MnO₂ are also discussed. XRD shows that the product is TiO₂-MnO₂ with amorphous phase. After being sintered at above 780 °C, it transfers into Ti_1-X Mn _X O₂ with a rutile structure. TEM shows that TiO₂-MnO₂ is the spherical particle. And the average diameter of the particles is 20 nm. The optical absorbance was determined by UV-265 spectrophotometer after dispersing the sample in the mixture of water and glycerol with the ratio of 1 : 1 equably. It is found that the nano-material possesses the advantages of both nano-TiO₂ and nano-MnO₂, and it has strong absorption in the UV and visible region. Photodegradation of dyes in an aqueous solution is investigated using nanometricTiO₂-MnO₂ as a photocatalyst. The results show that after 60 min illumination, the decolorization rate of the acidic red B and acidic black 234 dye can be as high as 100%.     

Fabrication and characterization of TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> composite nanoparticles and polyurethane/(TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript>) nanocomposite films

TiO₂–SiO₂ composite nanoparticles were prepared by a sol–gel process. To obtain the assembly of TiO₂–SiO₂ composite nanoparticles, different molar ratios of Ti/Si were investigated. Polyurethane (PU)/(TiO₂–SiO₂) hybrid films were synthesized using the “grafting from” technique by incorporation of modified TiO₂–SiO₂ composite nanoparticles building blocks into PU matrix. Firstly, 3-aminopropyltriethysilane was employed to encapsulate TiO₂–SiO₂ composite nanoparticles’ surface. Secondly, the PU shell was tethered to the TiO₂–SiO₂ core surface via surface functionalized reaction. The particle size of TiO₂–SiO₂ composite sol was performed on dynamic light scattering, and the microstructure was characterized by X-ray diffraction and Fourier transform infrared. Thermogravimetric analysis and transmission electron microscopy (TEM) employed to study the hybrid films. The average particle size of the TiO₂–SiO₂ composite particles is about 38 nm when the molar ratio of Ti/Si reaches to1:1. The TEM image indicates that TiO₂–SiO₂ composite nanoparticles are well dispersed in the PU matrix.     

超临界流体干燥法制备纳米TiO2-SnO2-SiO2复合光催化剂及其光催化性能研究

半导体多相光催化法作为一种污染治理新技术越来越受到人们的重视,在所使用的半导体光催化剂中,TiO2以无毒,催化活性高,价廉,无污染等特点,成为最具有前途的绿色环保型催化剂之一[1],但其自身具有局限性,如禁带宽度大,需在近紫外光下才能激发产生电子空穴对,对太阳光的利用率仅     

Thermal annealing synthesis of titanium-dioxide nanowire-nanoparticle hetero-structures

Crystalline TiO₂ nanowire-nanoparticle hetero-structures were successfully synthesized from titanium foils by using a simple thermal annealing method with the aid of CuCl₂ at the atmospheric pressure. Nanowires were grown from Ti foils by simply annealing Ti foils at 850 °C. Then, TiCl₄ was delivered to TiO₂ nanowires so as to precipitate TiO₂ nanoparticles on nanowire surfaces. At 750 °C reaction temperature, nanoparticles of tens of nanometers in diameter were well distributed on pre-grown nanowire forests. Nanoparticles were likely to be precipitated by TiCl₄ decomposition or oxidation and that require high temperatures above ∼650 °C. Electron microscopy, X-ray diffraction, and UV-vis spectroscopy analyses show they have the rutile polycrystalline structure with a slightly enlarged bandgap compared to that of bulk TiO₂. The influence of key synthesis parameters including reaction temperature, reaction time, and quantity of supplied materials on the incorporating nanoparticles was also systematically studied. The optimum reaction condition in the present paper was identified to be 750 °C annealing with repetitive 20 min reactions. A higher reaction temperature yielded larger diameter particles, and higher loading of Ti produced dense particles without changing the particle size. Finally, this method could be utilized for synthesizing other metal oxide nanowires-nanoparticle hetero-structures.     

Synthesize TiO<Subscript>2</Subscript> microspheres self-assembled from nanorods via hydrothermal treatment

The TiO2 microspheres were deposited on the glass substrates under certain conditions via hydrothermal reaction using 0.15 mol·L-1 TiCl3 saturated NaCl aqueous solution adding urea as an additive.The TiO2 is characterized rutile by results of SEM, TEM and XRD techniques, the TiO2 microspheres are large scale assembled from TiO2 nanorods. The affections on the products by the factors of the contents of urea being an additive (the key techniques), the reaction temperature, the reaction time and the concentration of TiCl3 were studied. The optimum condition was found, and the mechanism of reactions was discussed also.     

Microstructure and Photocatalytic Property of SiO<Subscript>2</Subscript>-TiO<Subscript>2</Subscript> Under Various Process Condition

Nanophase silica-titania particles were prepared by two different synthetic routes, namely, sol–gel and hydrothermal processing. The crystallinity and crystallographic phases, particle size and surface area of the materials were controlled by varying the calcination temperature, and/or the ratio of Si to Ti. It was determined by XRD that the crystallite sizes of SiO₂-TiO₂ prepared by sol–gel and hydrothermal processing decreased from 11 to 6 nm and 12 to 9 nm, respectively, as the mole fraction of silica was increased from 0.1 to 0.4. It is proposed that the presence of the amorphous silica suppresses the growth of anatase TiO₂ grains and their phase transformation to rutile. The photocatalytic decomposition rate of 1,4-dichlorobenzene (DCB) in aqueous solution with the sol–gel derived SiO₂-TiO₂ powder prepared at 750 °C was about 10 ± 5% higher than that observed with Degussa P25, whereas the SiO₂-TiO₂ samples prepared by hydrothermal processing at 250 °C showed a slightly lower decomposition rate than P25.     

Effect of calcination temperature on the microstructure of porous TiO<Subscript>2</Subscript> film

To obtain porous TiO₂ film, the precursor sol was prepared by hydrolysis of Ti isopropoxide and then complexed with trehalose dihydrate. The porous TiO₂ film was fabricated by the dip-coating technique on glass substrates using this solution. The TiO₂ film was calcined at 500 °C. The maximum thickness of the film from one-run dip-coating was ca. 740 nm. The film was composed of nanosized particle and pores. The porosity of the TiO₂ film was increased by addition of trehalose dihydrate to the sol. The porous TiO₂ films were calcined at different temperatures. The effects of calcination temperature on the microstructure of the porous TiO₂ film were investigated. The porous film prepared from sol containing trehalose still kept the porous structure after calcination at 950 °C. The phase transition temperature of the film from anatase to rutile was shifted from 650 to 700 °C by addition of trehalose to the sol.     

Synthesis and characterization of radiation sensitive TiO<Subscript>2</Subscript>/monazite photocatalyst

A TiO₂/monazite photocatalyst was prepared by embedding TiO₂ nanoparticles into a monazite substrate surface. TiCl₄ hydrolysis/citric acid chelating procedure under acidic conditions were used to synthesize the nanophase TiO₂ particles. The anatase TiO₂/monazite photocatalyst surface area, morphology, crystalline and elemental concentrations were characterized using Brunauer-Emmett-Teller (BET) method, scanning electron microscopy (SEM), X-ray diffraction (XRD), and inductively coupled plasma-atomic emission spectrometry (ICP-AES). Monazite contains a large amount of Ce-, La-, Nd- and Th-PO₄ compounds; it has been known as a natural mineral material with minor radioactivity. TiO₂-CeO₂ composite is a kind of radiation sensitive photocatalyst in which the radiations of thorium nuclides give energy to trigger TiO₂ and cerium ions which play an energy absorber with charge separator. The result showed that methylene blue and phenol were spontaneously photocatalytic decomposed by TiO₂/monazite composite even in a dark environment. A synergistic effect was also examined with applied exterior UV or ⁶⁰Co irradiation. A hybrid mechanism is proposed; according by the radioluminescence (RL) from excited Ce ion by γ-radiation soliciting CeO₂/TiO₂ heterojunction (HJ). This seems to be a possible mechanism to explain this self-activated photo-catalytic behavior.     

DSC investigation of nanocrystalline TiO<Subscript>2</Subscript> powder

The aim of the article is to investigate the influence of particle size on titanium dioxide phase transformations. Nanocrystalline titanium dioxide powder was obtained through a hydrothermal procedure in an aqueous media at high pressure (in the range 25–100 atm) and low temperature (≤200 °C). The as-prepared samples were characterized with respect to their composition by ICP (inductive coupled plasma), structure and morphology by XRD (X-ray diffraction), and TEM (transmission electron microscopy), thermal behavior by TG (thermogravimetry) coupled with DSC (differential scanning calorimetry). Thermal behavior of nanostructured TiO₂ was compared with three commercial TiO₂ samples. The sequence of brookite–anatase–rutile phase transformation in TiO₂ samples was investigated. The heat capacity of anatase and rutile in a large temperature range are reported.     

Comparison between the performance of an immobilized impinging jet stream reactor and a slurry impinging jet stream reactor for photocatalytic phenol degradation

A new immobilized photocatalytic impinging jet stream reactor was designed, and the influences of the effective parameters like jet flow rate, TiO₂ coating disc diameter, nozzle-to-disc distance, and initial concentration on phenol removal were investigated. The reactor was also used as a slurry reactor, and degradation efficiencies in both reactors were compared based on their catalyst loading. The results indicated that the slurry reactor has a higher degradation efficiency than the immobilized reactor at the same TiO₂ loading and other operational conditions. The slurry reactor needs to separate and recover the TiO₂ nanoparticles from the reaction medium which increases the overall process complexity and cost, while the immobilized reactor could be reused at least 4times without any significant decrease in removal efficiency. RTD result indicates that the tank in series model (N?=?5) could properly predict the reactors hydrodynamic behavior.     

Degradation of organic compounds on TiO<Subscript>2</Subscript> photocatalysts prepared by a hydrothermal method in the presence of NH<Subscript>4</Subscript>F

TiO₂ photocatalysts were synthesized by a hydrothermal method from tetraisopropyl orthotitanate (TPOT) in the presence of NH₄F with different NH₄F/Ti molar ratios (0, 0.25, and 1). The formation of a well-crystallized anatase phase of TiO₂ and the suppression of phase transition to rutile were observed, even at high calcination temperature, owing to the effects of NH₄F. The TiO₂ synthesized hydrothermally with NH₄F exhibited absorption with a shift to the longer wavelengths of the visible-light region. The hydrothermally synthesized TiO₂ with a moderate amount of NH₄F exhibited high photocatalytic activity for the degradation of alcohol diluted in water under both UV-light and visible-light irradiations.     

Characterization of Visible Light Response N-F Codoped TiO2 Photocatalyst Prepared by Acid Catalyzed Hydrolysis

N-F codoped TiO₂ (TONF) photocatalysts were prepared using acid catalyzed hydrolysis method from mixed aqueous solution of TiCl₄ and NH₄F. The photocatalytic activity of the TONF was evaluated through the degradation of phenol under both visible and UV light irradiation. X-ray photoelectron spectroscopy (XPS), UV-Vis diffuse reflectance spectroscopy (DRS), X-ray diffraction (XRD), scanning electron microscope (SEM), and N₂ adsorption isotherm were used to characterize the obtained powders. The results showed that N-F codoped TiO₂ exhibited significant improvement of visible light catalytic activity. N-F codoping could improve dispersion of TiO₂, inhibit particle size agglomeration, and retard phase transformation. Doped N could extend the light response of TiO₂ to visible light region. In addition, narrower band gap formed by F-doping was beneficial to the high visible light photocatalytic activity.     

Low temperature crystallization behavior of TiO<Subscript>2</Subscript> derived from a sol–gel process

TiO₂ nanoparticles are widely used for many applications and an understanding of the crystallization behavior of TiO₂ is essential, so that heat treatment conditions can be optimized for particular applications. The effect of sol–gel synthesis conditions on the crystallization behavior of TiO₂ has, therefore, been investigated. Complete crystallization to the anatase phase (determined by XRD and TEM analysis) was achieved during drying of the synthesis product at 95 °C. The nanoparticles grew during heat treatment, reaching ∼10–15 nm in diameter with a heat treatment at 450 °C. Explanations are offered for the observed differences in the crystallization and particle growth behavior of TiO₂ synthesized under various conditions.     

Conducting polyaniline-rutile TiO2 nanocomposites for the development of high-k dielectric materials

Inorganic dielectrics encapsulated in an organic matrix are showing excellent promise as novel dielectric materials. In this work, firstly highly organized crystalline nanoparticles of rutile TiO₂ were synthesized by acid hydrolysis of titanium isopropoxide at room temperature. Then we developed a novel dielectric material consisting of highly organized rutile TiO₂/polyaniline (PAni) nanocomposites by in-situ chemical oxidative polymerization. The structural, morphological, conducting, and dielectric properties of the rutile TiO₂/PAni nanoparticles have been evaluated by X-ray diffraction (XRD), scanning electron microscopy (SEM), high resolution-transmission emission microscopy (HR-TEM), four-point probe technique, CV (Capacitance versus Voltage), and Impedance analyzer. The nanocomposites show 70 times higher permittivity compared to rutile nanoparticles and much higher compared to anatase/PAni (ES) nanocomposites at 10 MHz. Large interfacial polarizations, nanostructure, and dopant levels are the key factors for the large dielectric constant of the nanocomposites. The rutile/PAni (ES) nanocomposites might see potential uses in super-capacitors, gate dielectric in transistors, and capacitive-type gas sensors.     

Influence of NH<Subscript>3</Subscript>-treating temperature on visible light photocatalytic activity of N-doped P<Subscript>25</Subscript>-TiO<Subscript>2</Subscript>

The influence of NH₃-treating temperature on the visible light photocatalytic activity of N-doped P₂₅-TiO₂ as well as the relationship between the surface composition structure of TiO₂ and its visible light photocatalytic activity were investigated. The results showed that N-doped P₂₅-TiO₂ treated at 600°C had the highest activity. The structure of P₂₅-TiO₂ was converted from anatase to rutile at 700°C. Moreover, no N-doping was detected at the surface of P₂₅-TiO₂. There was no simply linear relationship between the visible light photocatalytic activity and the concentration of doped nitrogen, and visible light absorption. The visible light photocatalytic activity of N-doped P₂₅-TiO₂ was mainly influenced by the synergistic action of the following factors: (i) the formation of the single-electron-trapped oxygen vacancies (denoted as V_o^·); (ii) the doped nitrogen on the surface of TiO₂; (iii) the anatase TiO₂ structure.     

New In-Situ Sampling and Analysis of the Production of CeO<Subscript>2</Subscript> Powders from Liquid Precursors in a rf Thermal Plasma Reactor. Part 2: Analysis of CeO<Subscript>2</Subscript> Powders,Fuel Addition,and Image Analysis

A novel reactor design, sampling probe and wet collection system were used to investigate the combined effects of plasma operating parameters and particle collection mechanisms on the synthesis of CeO₂ particles from liquid precursors. The sampling of particles in-flight and the collection of particles at several reactor regions were used to provide experimental evidence of particle size at different reactor locations at various plasma operating conditions, i.e., power and plasma gas flow rates. This information provided a picture of how CeO₂ particles were formed and how these particles were collected in various locations. The effect of adding water-soluble fuels (alanine and glycine) to the original cerium nitrate solutions was also investigated. Fuel addition decreased the temperature of CeO₂ formation by acting as a local heat source as a result of fuel auto-ignition. Photographs of the particles in-flight were taken using a fast speed CCD camera.     

Study of the Stable Nanocrystalline TiO<Subscript>2</Subscript> Hydrosol and its Fractions

Nanodisperse TiO₂ hydrosol and two of its fractions stabilized by HCl are studied. The anatase nanocrystalline fractions are obtained by the stepped coagulation of the stable sol using dependence of coagulation thresholds on size of nanocrystallites. X-Ray investigation in small and wide angles of scattering has revealed that the anatase nanocrystallites have a shape of 2.5–3 nm thick elongated plates with 8–18 nm lateral sizes. The concentrated hydrosols with the reduced HCl content prepared from the anatase fractions are shown to form an ordered structure. Narrow fractions of TiO₂ nanocrystallites obtained from the stable hydrosols seem to be promising for the preparation of highly ordered structures with a nanometer periodicity.     

Cooperation among N,F and Fe in tri-doped TiO<Subscript>2</Subscript> photocatalyst

TiO₂ photocatalysts tri-doped with N, F and Fe were synthesized by a sol–gel method. The cooperation of N, F and Fe in tri-doped TiO₂ was verified by monitoring NH₃ decomposition, X-ray diffraction (XRD), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS) and ultraviolet–visible (UV–Vis) absorption spectroscopy, and by the simulation based on the density functional theory (DFT). The results from NH₃ decomposition revealed that the cooperation of N, F and Fe broadened the optical response of TiO₂ to the visible light range and also enhanced the photocatalytic activity of TiO₂ under UV light. The reusability of the tri-doped TiO₂ sample after three cycles under UV and visible light irradiation was very good. XRD patterns and SEM and HRTEM images indicated that the tri-doped sample was nanometric anatase with a small amount of rutile with an average particle size of 18 nm. Tri-doping with N, F and Fe suppressed the phase transition from anatase to rutile and also resulted in some more lattice defects. XPS analysis showed that the N, F and Fe atoms were doped into the TiO₂ lattice. UV–Vis absorption spectra of the tri-doped TiO₂ showed that its optical absorption edge was moved up to 640 nm and its UV absorption was also enhanced. The DFT results confirmed that the cooperation of Fe 3d and N 2p orbits narrowed the band gap of TiO₂ and the F 2p orbit broadened the upper valence bands. The synergistic electron density around N, F and Fe in tri-doped TiO₂ was capable of enhancing the photochemical stability and reusability of TiO₂.     

On the Formation of TiO<Subscript>2</Subscript> Nanoparticles Via Submerged Arc Discharge Technique: Synthesis,Characterization and Photocatalytic Properties

We report a simple and inexpensive synthesis route of TiO₂ nanoparticles using electrical arc discharge between titanium electrodes in oxygen bubbled deionized (DI) water followed by heat treatment. The resulting nanoparticles were characterized using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), dynamic light scattering (DLS), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). XRD patterns demonstrate formation of TiO₂ phase in oxygen bubbled water after heat treatment and dominance of rutile to anatase phase. The size and morphology of TiO₂ nanoparticles were studied using different arc currents as a crucial parameter in properties of final product. Microscopic studies reveal nanosize spherical particles. DLS results indicate that at 20 A arc current, the size of the particles is about 37 nm and increases to 59 nm by increasing the arc current up to 40 A. Photodegradation of Rhodamine B (Rh. B) as a standard pollution shows that heat treated samples in oxygen bubbled water for 2 h at 500 °C, have more photocatalytic activity due to enhancement in crystallinity.