W型单模单偏振光纤基模截止归一化频率

用数值计算了 W型单模单偏振光纤基模截止归一化频率 ,分析了基模截止归一化频率与光纤结构参数的关系 ,得出了在外包层远离纤芯的情况下 ,基模截止归一化频率仅与内包层折射率深度有关 ,同时给出了其相应的近似函数关系和曲线     

W型单模单偏振光纤隧道效应的模场分析

给出了W型单模单偏振光纤基模模场在截止前,截止时和截止后的具体计算方法,利用基模模场分析了W型单模单偏振光纤隧道效应发生的过程,强弱和方向,得出了W型单模单偏振光纤隧道效应随其基模的截止而显著增强,并且主要集中在椭圆内包层短半轴方向的结论。     

双包层手性光纤中导模的光功率特性

在对W型阶跃双包层手性光纤进行解析求解的基础上,对几个低阶导模的功率特性进行了仔细的研究.对典型的内包层厚度,计算了几个低阶模留在纤芯中的光功率随纤芯和内外包层的手性参数的变化关系曲线,讨论了纤芯和内外包层的手性参量以及内包层厚度对不同符号模式的功率特性的影响.内包层厚度越大,功率越被限制在纤芯中.随着纤芯中手性参量的增大, HE－11模和HE－21模（HE01模）限制在纤芯中的光功率缓慢增加,而HE11模和HE21模（HE02模）限制在纤芯中的光功率则逐渐减小.包层手性参量的作用正好与此相反.     

W型色散光纤带通滤波特性的研究

结合色散光纤在线滤波和W型光纤的长波长截止性能,研究了W型色散光纤的带通滤波特性.选取SiO2作为纤芯,一定掺杂浓度的SiO2-F和SiO2-B2O3分别作为内外包层,经过设计,实现了带通滤波功能.通过有限元法仿真及数值计算,得出了基模的能量损耗谱及通带内外各个波长处的横截面能量分布图,其截止波长和带宽可以通过控制掺杂...     

W型单模单偏振光纤基模截止的条件

给出了 W型单模单偏振光纤基模截止的必要条件。通过对基模截止波长的数值计算 ,分析了这个必要条件的充分性。结论是 :对于圆形内包层 W型光纤来说 ,这是必要的而又充分的条件 ;对于低椭圆度内包层 W型单模单偏振光纤来说 ,它可以在较高的精度上近似作为充分条件 ,而对于高椭圆度内包层 W型单模单偏振光纤来说 ,它仅仅只是必要条件而非充分条件     

左手材料纤芯双包层光纤的传输特性

对纤芯为左手材料,内包层和外包层都为右手材料的双包层光纤进行了分析.在弱导情况下,且不考虑介质损耗,由亥姆霍兹方程出发,得到了HE、EH、TE和TM导模的色散方程,并在远离截止条件下,对其进行简化.所有的TE和TM模都是简并的.分别讨论了内包层折射率和厚度对该左手材料光纤最低阶导模的影响,画出了各自的色散曲线,并和右手材料光纤导模相应色散曲线进行了比较,发现左手材料光纤的低阶导模具有反常的色散特性.     

用于极寒温度的特种光纤的结构与弯曲损耗研究

设计了一种适用于极寒温度(-70℃)条件的耐低温的特种光纤,其结构包括纤芯层、内包层、凹陷包层和外包层.研究了光纤芯层/内包层的相对折射率差与弯曲损耗之间的关系,对比了不同涂覆层模量厚度和对光纤微弯损耗的影响.优化光纤拉丝工艺,获得了一种可长期应用于-70℃极寒温度下,在1 550nm、1 625nm波段处附加损耗低于0.01dB/km的石英光纤.本文研究工作为耐极寒光纤、光纤复合架空地线的制备及产业化提供了可靠的理论与实验依据.     

掺铒孔辅助导光光纤的特性研究与优化设计

掺铒孔辅助导光光纤是由掺铒的高折射率纤芯、低折射率包层和少量的空气孔组成. 采用有限元法分析了掺铒孔辅助导光光纤的模式特性；给出了数值计算截止波长和模场直径的方法；提出了改进的平均粒子数反转度迭代算法来数值计算掺铒光纤放大器的增益和噪声系数. 研究空气孔对掺铒孔辅助导光光纤的截止波长、模场直径和放大器的增益系数的影响. 发现：减小相对孔芯距的值，可使截止波长向短波长移动，减小模场直径的值；当孔的相对大小较大时，截止波长、模场直径和增益的最大值基本上不随孔的相对大小的增大而改变. 最后，综合考虑掺铒光纤基模和二阶模的截止波长、与普通单模光纤的熔接损耗、放大器的增益和噪声系数等因素，优化设计了掺铒孔辅助导光光纤的四个结构参量——纤芯半径、纤芯与包层的折射率差、相对孔芯距和孔的相对大小. 关键词： 孔辅助导光光纤 掺铒光纤 光纤放大器 有限元法     

单模光纤折射率分布对偏振模色散的影响

利用将任意非圆柱等效为椭圆的方法分析和计算了单模光纤中包层和芯层折射率分布不同心导致的偏振模色散，得到了两个偏振模式的传输常数差△β和偏振模色散△τ与偏心比、入射光的波长、芯层半径、相对折射率差的关系曲线，为实践中昼减小单模光纤的偏振模色散提供理论上的指导。与椭圆度引起的偏振模色散相比，不同心引起的偏振模色散具有相同的数量级。     

同心椭圆度光纤的耦合系数计算

应用耦合模原理，用Ｍａｔｈｉｅｕ函数表示纤芯，包层为同心椭圆度的光纤中的电磁场，在适当近似条件下，求得了基模场中的偶模耦合系数表示式，并给出截止条件下的离心率－耦合系数，半长轴－耦合系数曲线。     

Polarization characteristic calculation of three-layer elliptical single-mode fibres

A vector solution is obtained for fields of fundamental modes of an elliptical three-layer optical fibre, which is valid for small ellipticity of boundaries between the layers and for arbitrary differences of core and cladding indices. The modal birefringence is investigated as a function of fibre parameters on the basis of this solution. It is shown that the two-step fibre birefringence is larger than the W-fibre birefringence for equal differences of the core and inner cladding indices. The relationship is inverse for equal differences of the core and outer cladding indices. The correlation between the birefringence value and the effective diameter of the single-mode fibre is discussed.     

同心椭圆柱-纳米管结构的双重Fano共振研究

提出了一种同心椭圆柱-纳米管复合结构,该结构由金纳米管中内嵌椭圆形金柱构成,利用时域有限差分法分析了尺寸参数、周围环境及纳米管内核材料对该结构光学性质的影响.结果表明,调节椭圆柱芯的旋转角度可产生双重偶极-偶极Fano共振,其主要是由椭圆柱芯的纵向或横向偶极共振模式与纳米管的偶极成键和反成键模式杂化形成的超辐射成键模式和亚辐射成键模式之间的相互作用产生的,且共振特性可通过调节复合结构的尺寸参数控制,随椭圆柱长轴或短轴的增大而红移,随纳米管外径的增大或整体尺寸的减小而蓝移,当纳米管内径增大时高频Fano共振随着红移,而低频Fano共振先蓝移再红移,同时其对外界环境的变化不敏感,但对纳米管内核材料变化有着较好的响应.利用等离激元杂化理论对该现象进行了解释.这些结果可为构造其他类型的多波段Fano共振二维或三维纳米结构提供一种新的方式.     

Simultaneous Measurement of Temperature and Refractive Index of Liquid Using Cladding-Etched Double-Core Fiber Bragg Grating

Abstract

This study proposed and demonstrated a fiber Bragg grating sensor for simultaneous detection of the temperature and refractive index of a liquid. The fiber Bragg grating is composed of three index layers: an inner core, an outer core, and a cladding. The cladding was etched for evanescent wave coupling between the outer core mode and an external liquid. The Bragg wavelength of the inner core mode is used for obtaining temperature data, while the refractive index for the liquid was determined by using the difference between the Bragg wavelength of the inner core mode and that of outer core mode.     

Central distance of interferential mode patterns of elliptical cora two-mode fiber

By means of the weakly guiding approximation, the mode spot sizes Wx and Wy of the fundamental mode along the semimajor (x-direction) and semiminor (y-direction) axes of the fiber core in elliptical core twomode fiber are discussed. The variation of their ratio value Wx/Wy with the operation wavelength λ and the length ratio a/b between the semimajor axis and the semiminor axis of the fiber core is analyzed. Based onthis analysis, the distribution figures of two-lobe interferential mode patterns are evaluated and simulated quantitatively for different phase difference changes between LPo1 and LPeven11 modes. The two-lobeinterferential mode patterns have the same profile and distribute symmetrically when the phase differenceequals π/2. Their central distance S becomes larger when WX/Wy augments gradually. Furthermore,the equation about the central distance S of the two-lobe interferential mode patterns is given when the operation wavelength varies between 0.65 and 1.31 μm, which is important to applications shuch as sensors and coupling devices between different fibers.     

水雾包裹沙尘颗粒核壳结构的散射特性研究

基于离散偶极子近似法(DDA),对水雾包裹沙尘颗粒的核壳结构光学特性进行研究,计算了长短轴比例为2∶1的椭球形粒子的核壳结构内、外层厚度及散射角度变化对光散射特性的影响。结果表明,内核大小不变,外层厚度由1.2 μm增大到4.8 μm,核壳双层颗粒散射系数和消光系数由3.4和3.43降低到2.543和2.545,且散射相对强度也明显增大。外层厚度不变,内核厚度由0.6 μm增加到2.4 μm,散射系数和消光系数由3.105和3.111变化为2.76和2.9;可见外层厚度对核壳双层颗粒散射特性的影响更大,这是由于散射光主要与外层物质相互作用引起的。散射相对强度随波长的增加而降低,随核壳结构尺度的增加呈现递增的规律。该结果对大气中气溶胶和水雾共同作用时的散射特性,激光在其中的传输特性等研究有参考价值。     

Bending losses of a doubly clad slab waveguide

This communication considers the bending losses of a doubly clad slab waveguide in which the core has the largest refractive index and the inner cladding has the lowest. It is found that the bending losses are drastically reduced by inserting a low-index inner cladding between the core and the outer cladding.     

An analytical study of a doubly clad compressed ellipse optical waveguide

Using an analytical method based on boundary matching technique, the modal behavior and cutoff frequencies of a compressed ellipse doubly clad optical waveguide is studied. The proposed waveguide consists of a core region of higher refractive index with two cladding regions: one is inner cladding and the other is outer cladding. We take appropriate orthogonal coordinates for the proposed structure and impose the boundary conditions to obtain the characteristic equation. The effect of the width of inner cladding layer on the dispersion characteristic is observed. It is found that the width of inner cladding is able to tailor the dispersion characteristic and cutoff condition of the waveguide up to a certain limit.