NADP+-Specific Isocitrate Dehydrogenase from Oleaginous Yeast Yarrowia lipolytica CLIB122: Biochemical Characterization and Coenzyme Sites Evaluation

NADP⁺-dependent isocitrate dehydrogenase from Yarrowia lipolytica CLIB122 (YlIDP) was overexpressed and purified. The molecular mass of YlIDP was estimated to be about 81.3 kDa, suggesting its homodimeric structure in solution. YlIDP was divalent cation dependent and Mg²⁺ was found to be the most favorable cofactor. The purified recombinant YlIDP displayed maximal activity at 55 °C and its optimal pH for catalysis was found to be around 8.5. Heat inactivation studies revealed that the recombinant YlIDP was stable below 45 °C, but its activity dropped quickly above this temperature. YlIDP was absolutely dependent on NADP⁺ and no NAD-dependent activity could be detected. The K _m values displayed for NADP⁺ and isocitrate were 59 and 31 μM (Mg²⁺), 120 μM and 58 μM (Mn²⁺), respectively. Mutant enzymes were constructed to tentatively alter the coenzyme specificity of YlIDP. The K _m values for NADP⁺ of R322D mutant was 2,410 μM, being about 41-fold higher than that of wild type enzyme. NAD⁺-dependent activity was detected for R322D mutant and the K _m and k _cat values for NAD⁺ were 47,000 μM and 0.38 s^?1, respectively. Although the R322D mutant showed low activity with NAD⁺, it revealed the feasibility of engineering an eukaryotic IDP to a NAD⁺-dependent one.     

Expression,Purification, and Characterization of NADP+-Dependent Malic Enzyme from the Oleaginous Fungus Mortierella Alpina

Malic enzymes are a class of oxidative decarboxylases that catalyze the oxidative decarboxylation of malate to pyruvate and carbon dioxide, with concomitant reduction of NAD(P)⁺ to NAD(P)H. The NADP⁺-dependent malic enzyme in oleaginous fungi plays a key role in fatty acid biosynthesis. In this study, the malic enzyme-encoding complementary DNA (cDNA) (malE1) from the oleaginous fungus Mortierella alpina was cloned and expressed in Escherichia coli BL21 (DE3). The recombinant protein (MaME) was purified using Ni-NTA affinity chromatography. The purified enzyme used NADP⁺ as the cofactor. The K _m values for l-malate and NADP⁺ were 2.19?±?0.01 and 0.38?±?0.02 mM, respectively, while the V _max values were 147?±?2 and 302?±?14 U/mg, respectively, at the optimal condition of pH 7.5 and 33 °C. MaME is active in the presence of Mn²⁺, Mg²⁺, Co²⁺, Ni²⁺, and low concentrations of Zn²⁺ rather than Ca²⁺, Cu²⁺, or high concentrations of Zn²⁺. Oxaloacetic acid and glyoxylate inhibited the MaME activity by competing with malate, and their K _i values were 0.08 and 0.6 mM, respectively.     

Synthesis of single-crystal magnesium-doped spinel lithium manganate and its applications for lithium-ion batteries

Single-crystal magnesium-doped spinel lithium manganate cathode materials are prepared by the hydrothermal method followed by the heat treatment. XRD patterns reveal that Mg²⁺ions have already diffused into the Li_1.088Mn_1.912O₄ crystal structure and not affect the Fd3m space group. SEM images demonstrate that the magnesium-doped spinel lithium manganates show uniform polyhedral single crystals with 2–4 μm. Electrochemical performance demonstrates that the optimized composition of Li_1.088Mg_0.070Mn_1.842O₄ electrode exhibits the best electrochemical properties. It delivers 92.0 mAh g^?1 at 8C rates and corresponds to 90.8% capacity retention (vs. 1C), far higher than those of the pristine electrode (70.4 mAh g^?1 and 69.2%). In addition, the Li_1.088Mg_0.070Mn_1.842O₄ electrode also shows 95.5% capacity retention after 100 cycles at 1C, while the pristine electrode only shows 91.0% capacity retention. The excellent electrochemical performances of Li_1.088Mg_0.070Mn_1.842O₄ electrode are ascribed to the suppressed polarization, more stable crystal structure, and better kinetic characteristics.     

Sn-doped Li<Subscript>1.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>O<Subscript>2</Subscript> cathode materials for lithium-ion batteries with enhanced electrochemical performance

Sn-doped Li-rich layered oxides of Li_1.2Mn_0.54-x Ni_0.13Co_0.13Sn _x O₂ have been synthesized via a sol-gel method, and their microstructure and electrochemical performance have been studied. The addition of Sn⁴⁺ ions has no distinct influence on the crystal structure of the materials. After doped with an appropriate amount of Sn⁴⁺, the electrochemical performance of Li_1.2Mn_0.54-x Ni_0.13Co_0.13Sn _x O₂ cathode materials is significantly enhanced. The optimal electrochemical performance is obtained at x = 0.01. The Li_1.2Mn_0.53Ni_0.13Co_0.13Sn_0.01O₂ electrode delivers a high initial discharge capacity of 268.9 mAh g^?1 with an initial coulombic efficiency of 76.5% and a reversible capacity of 199.8 mAh g^?1 at 0.1 C with capacity retention of 75.2% after 100 cycles. In addition, the Li_1.2Mn_0.53Ni_0.13Co_0.13Sn_0.01O₂ electrode exhibits the superior rate capability with discharge capacities of 239.8, 198.6, 164.4, 133.4, and 88.8 mAh g^?1 at 0.2, 0.5, 1, 2, and 5 C, respectively, which are much higher than those of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ (196.2, 153.5, 117.5, 92.7, and 43.8 mAh g^?1 at 0.2, 0.5, 1, 2, and 5 C, respectively). The substitution of Sn⁴⁺ for Mn⁴⁺ enlarges the Li⁺ diffusion channels due to its larger ionic radius compared to Mn⁴⁺ and enhances the structural stability of Li-rich oxides, leading to the improved electrochemical performance in the Sn-doped Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ cathode materials.     

New PCT probes featuring N-phenylmonoaza-18-crown-6 and aryl/pyridyl oxadiazoles: optical spectral studies of solvent effects and selected metal ions

Aryl/pyridyl oxadiazole chromophores 6, 8 and 10, carrying N-phenyl aza-18-crown-6 have been synthesized as new photo-induced charge transfer (PCT) probes. While, the absorption spectra of the hosts experienced a slight negative solvatochromism, however the emission bands were dramatically red shifted (Stokes shifts up to 178 nm) in solvents of increasing polarity. Among the metal ions tested, Li⁺, Na⁺, K⁺ and Mg²⁺ did not appreciably perturbed the optical properties of the hosts. On the other hand, Ba²⁺ and to a lesser extent Ca²⁺ induced marked blue shifts in both the absorption and emission spectra of the hosts. The magnitude of cation induced spectral blue shifts corresponded with the increasing acceptor strength of the attached aryl/pyridyl groups in the host molecules. The blue shifts and the stability constants were found to follow the order Ba²⁺ > Ca²⁺ ? Mg²⁺ > Na⁺ > Li⁺ > K⁺. Competitive experiments performed with a matrix of ions also revealed superior binding affinity of Ba²⁺ with all the hosts examined. Noteworthily, the deep yellow solution (λ_max, 386 nm) of the host 10 was completely bleached (λ_max, 320 nm), in the company of Ba²⁺ thereby allowing the naked eye detection of this ion.     

球形PVC-MnO2离子筛的制备及锂吸附性能

本实验室前期所制备的Li4Mn5O12超细粉末在卤水体系中对Li+具有较大的吸附容量和良好的选择性。但由于超细粉体的流动性和渗透性差,无法直接应用于固定床,需对粉末吸附材料进行成型造粒,以便于实际应用。本论文采用聚氯乙烯为粘结剂,制备出粒径约为2.0~3.5 mm的球形PVC-Li4Mn5O12,经盐酸处理后得到球形PVC-MnO2离子筛。并通过扫描电镜(SEM)、X射线衍射仪(XRD)、静态和动态连续锂吸附实验研究了球形离子筛形貌和锂离子吸附性能。结果表明,球形离子筛对Li+的吸附容量高达5.28 mmol.g-1,在混合溶液中对Li+具有良好的选择性,这对于在盐湖卤水或海水提锂具有重要的实用意义。     

Preparation and electrochemical properties of nano-sized cryptomelane particles for the formation of potentiometric potassium ion sensors

The potentiometric response of 100-nm spherical K_1.3Mn₈O₁₆ particles versus K⁺ ions has been studied in aqueous media using a polymeric technology. The stoichiometry of this material evolves in potassium nitrate solution towards K_1.08Mn₈O₁₆. A stable and reversible response has been obtained with a sensitivity of 47 mV dec^?1 in the range from 8?×?10^?5 to 1 mol·L^?1, and a rather good selectivity towards Li⁺, Na⁺, Mg²⁺ and Ca²⁺ $\left( {{\text{log K}}_{{{{\text{K}}^{\text{ + }} } \mathord{\left/ {\vphantom {{{\text{K}}^{\text{ + }} } {{\text{X}}^{n + } }}} \right. \kern-0em} {{\text{X}}^{n + } }}} \approx - {\text{3}}} \right)$ . We assume that this potentiometric response is the result of the ability of K_1.08Mn₈O₁₆ to specifically adsorb K⁺ ions.     

Variation of the composition and properties of lithium manganese oxide spinel in lithiation-delithiation cycles

The behavior of the variable-composition spinel Li_{1 + x} Mn_{2 ? x} O₄ is examined in repeated cycles consisting of lithiation in 0.2 M LiOH and delithiation in 0.3 M HNO₃. For 0 < x < 0.33, delithiation is accompanied by the redox reaction 2Mn³⁺ → Mn⁴⁺ + Mn²⁺ and Li⁺ ? H⁺ ion exchange. The spinel undergoes partial conversion into λ-□MnO₂. Vacancies (□) build up at the 8a sites of the spinel structure. Mn²⁺ ions pass into the solution, and, accordingly, the spinel dissolves. Lithiation is accompanied by the redox reaction 4Mn⁴⁺ → 3Mn³⁺ + Mn⁷⁺ and ion exchange, and the proportion of vacancies □ at the 8a sites of the spinel structure decreases. The spinel undergoes partial dissolution because of Mn²⁺ and MnO _? ⁴ ions passing into the solution. The Li⁺ selectivity of the spinel is the property of the crystallite core. The crystallite surface is capable of sorbing Na⁺ ions.     

Cation exchange, interlayer spacing, and thermal analysis of Na/Ca-montmorillonite modified with alkaline and alkaline earth metal ions

Na-montmorillonites were exchanged with Li⁺, K⁺, Rb⁺, Cs⁺, Mg²⁺, Ca²⁺, Sr²⁺, and Ba²⁺, while Ca-montmorillonites were treated with alkaline and alkaline earth ions except for Ra²⁺ and Ca²⁺. Montmorillonites with interlayer cations Li⁺ or Na⁺ have remarkable swelling capacity and keep excellent stability. It is shown that metal ions represent different exchange ability as follows: Cs⁺?>?Rb⁺?>?K⁺?>?Na⁺?>?Li⁺ and Ba²⁺?>?Sr²⁺?>?Ca²⁺?>?Mg²⁺. The cation exchange capacity with single ion exchange capacity illustrates that Mg²⁺ and Ca²⁺ do not only take part in cation exchange but also produce physical adsorption on the montmorillonite. Although interlayer spacing d ₀₀₁ depends on both radius and hydration radius of interlayer cations, the latter one plays a decisive role in changing d ₀₀₁ value. Three stages of temperature intervals of dehydration are observed from the TG/DSC curves: the release of surface water adsorbed (36?C84?°C), the dehydration of interlayer water and the chemical-adsorption water (47?C189?°C) and dehydration of bound water of interlayer metal cation (108?C268?°C). Data show that the quantity and hydration energy of ions adsorbed on montmorillonite influence the water content in montmorillonite. Mg²⁺-modified Na-montmorillonite which absorbs the most quantity of ions with the highest hydration energy has the maximum water content up to 8.84%.     

Metal cation-induced multifluorescence of azacrown-substituted (tetrafluorophenyl)imidazo[1,2-a]pyridine

ortho-Azacrown-substituted (tetrafluorophenyl)imidazo[1,2-a]pyridine (2) in an acetonitrile solution emits 380 nm light in the presence of Li⁺ cation and emits 460 nm light in the presence of Zn²⁺, Mg²⁺ or H⁺ cation. In contrast, para-azacrown-substituted analogue (1) emits three different fluorescent lights responding to Li⁺, Zn²⁺ or H⁺ cation, respectively; 388 nm light to Li⁺ cation, 433 nm light to Zn²⁺ cation or 469 nm light to H⁺ cation.     

Improvement of electrochemical performance for Li-rich spherical Li1.3[Ni0.35Mn0.65]O2+x modified by Al2O3

The Li-rich Li_1.3[Ni_0.35Mn_0.65]O_2+x microspheres are firstly prepared and subsequently transferred into the Al₂O₃-coated Li-rich Li_1.3[Ni_0.35Mn_0.65]O_2+x microspheres by a simple deposition method. The as-prepared samples are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and charge/discharge tests. The results reveal that the Al₂O₃-coated Li-rich Li_1.3[Ni_0.35Mn_0.65]O_2+x sample has a typical α-NaFeO₂ layered structure with the existence of Li₂MnO₃-type integrated component, and the Al₂O₃ layer is uniformly coated on the surface of the spherical Li-rich Li_1.3[Ni_0.35Mn_0.65]O_2+x particles with a thickness of about 4 nm. Importantly, the Al₂O₃-coated Li-rich sample exhibits obviously improved electrochemical performance compared with the pristine one, especially the 2 wt.% Al₂O₃-coated sample shows the best electrochemical properties, which delivers an initial discharge capacity of 228 mAh g^?1 at a rate of 0.1 C in the voltage of 2.0–4.6 V, and the first coulombic efficiency is up to 90 %. Furthermore, the 2 wt.% Al₂O₃-coated sample represents excellent cycling stability with capacity retention of 90.9 % at 0.33 C after 100 cycles, much higher than that of the pristine one (62.2 %). Particularly, herein, the typical inferior rate capability of Li-rich layered cathode is apparently improved, and the 2 wt.% Al₂O₃-coated sample also shows a high rate capability, which can deliver a capacity of 101 mAh g^?1 even at 10 C. Besides, the thin Al₂O₃ layer can reduce the charge transfer resistance and stabilize the surface structure of active material during cycling, which is responsible for the improvement of electrochemical performance of the Li-rich Li_1.3[Ni_0.35Mn_0.65]O_2+x .     

Characterization of xylitol dehydrogenase from debaryomyces hansenii

The xylitol dehydrogenase (EC 1.1.1.9) from xylose-grown cells ofDebaryomyces hansenii was partially purified in two Chromatographic steps, and characterization studies were carried out in order to inves tigate the role of the xylitol dehydrogenase-catalyzed step in the regu lation of D-xylose metabolism. The enzyme was most active at pH 9.0–9.5, and exhibited a broad polyol specificity. The Michaelis con stants for xylitol and NAD⁺ were 16.5 and 0.55 mM, respectively. Ca²⁺, Mg²⁺, and Mn²⁺ did not affect the enzyme activity. Conversely, Zn²⁺, Cd²⁺, and Co²⁺ strongly inhibited the enzyme activity. It was concluded that NAD⁺-xylitol dehydrogenase from D.hansenii has similarities with other xylose-fermenting yeasts in respect to optimal pH, substrate specificity, and K_m value for xylitol, and therefore should be named L-iditol:NAD⁺-5-oxidoreductase (EC 1.1.1.14). The reason D.hansenii is a good xylitol producer is not because of its value of K_m for xylitol, which is low enough to assure its fast oxidation by NAD⁺ xylitol dehydrogenase. However, a higher K_m value of xylitol dehydro genase for NAD⁺ compared to theK _m values of other xylose-ferment ing yeasts may be responsible for the higher xylitol yields.     

Neutron Diffraction Study on the Structure of Aqueous LiNO3 Solutions

Neutron diffraction measurements were carried out at 25 °C for aqueous LiNO₃ heavy water solutions, (*LiNO₃) _x (D₂O)_1?x where x = 0.1, 0.05 and 0.01, in which the ⁶Li/⁷Li isotopic ratios were varied. Structural information on intermolecular nearest neighbor Li⁺···D₂O interactions in the extensive concentration range was derived from the first-order difference function, ?_Li(Q), obtained from the difference in scattering cross sections between ⁶Li- and ⁷Li-enriched sample solutions. The nearest neighbor Li⁺···O distance and coordination number for sample solution with x = 0.1 were determined to be r _LiO = 1.969 (8) Å and n _LiO = 4.12 (6), respectively, corresponding to the four-coordinated Li⁺ ion in the solution. On the other hand, those obtained for the solution with x = 0.01 are r _LiO = 2.00 (2) Å and n _LiO = 6.0 (2), respectively, indicating that hexaaqua Li⁺ is dominant in the dilute solution. These results clearly indicate that a concentration dependence of the hydration number of Li⁺ occurs in the aqueous solutions.     

Preparation of PFSA/PSf hollow fiber composite membranes with recovered PFSA for the pervaporation separation of EtOH/H2O

Perfluorosulfonic acid/Polysulfone(PFSA/PSf) hollow fiber composite membranes have been prepared by dip-coating method using PSf ultrafiltration (UF) membrane as substrate with recovered PFSA. The composite membranes were applied to the pervaporation separation of 95% ethanol (EtOH)/H₂O mixture. SEM images show that the thickness of the PFSA skin layer of the composite membranes is about 2 μm, much thinner than those of other PFSA composite membranes revealed in the literatures. Effects of annealing temperature, coating solution concentration and counter-ions of PFSA on the pervaporation performances of the composite membranes were investigated. The total flux decreases and separation factor increases with the increase of annealing temperature. The highest permeation flux of 3230 g m^?2 h^?1 and a separation factor of 5.4 is obtained for the composite membrane annealed at 80°C. The lowest permeation flux of 396 g m^?2 h^?1 and a separation factor of 27.7 is obtained for the composite membrane annealed at 160°C. The permeation performances of the PFSA/PSf composite membrane are evidently influenced by the counter-ions of PFSA. The flux sequence of the PFSA/PSf composite membranes with different counter-ions is H⁺>Li⁺>Ca²⁺>Mg²⁺>Na⁺>K⁺>Ba²⁺>Fe³⁺>Al³⁺, and the separation factor sequence is H⁺<Li⁺<Al³⁺<Na⁺<Mg²⁺<Ca²⁺<K⁺<Ba²⁺<Fe³⁺. The apparent activation energy ΔE _app values of the composite membranes with different counter-ions were calculated by Arrhenius law. The sequence of ΔE _app values for the membranes with monovalent counter-ions is Li⁺>Na⁺>K⁺. There are very little variations of ΔE _app values between the composite membranes with three divalent counter-ions (Mg²⁺, Ca²⁺ and Ba²⁺), and the ΔE _app values of the composite membranes with two trivalent counter-ions (Fe³⁺ and Al³⁺) are relatively high.     

Competitive 7Li NMR Study on the Mn2+, Zn2+ and Cd2+ Complexes of Two New Branched Hexadentate (N6) Amines Containing the Pyridine Moiety in Nitromethane and Acetonitrile Solutions

Lithium-7 NMR spectroscopy was used to investigate the stoichiometry and stability of a Li⁺ complex with two new branched amines, 4,7-bis(2-pyridylmethyl)-4,7-diazadecane-1,10-diamine (L¹) and 4,8-bis(2-pyridylmethyl)-4,8-diazaundecane-1,11-diamine (L²), in acetonitrile and nitromethane. A competitive ⁷Li NMR method was also employed to probe the complexation of Mn²⁺, Zn²⁺ and Cd²⁺ ions with L¹ and L² in the same solvent systems. The formation constants of the resulting complexes were evaluated from computer fitting of the mole ratio data with an equation that relates the observed chemical shifts to the formation constant. In both solvents, the stability of the resulting 1:1 complexes was found to vary in the order Cd²⁺ > Zn²⁺ > Mn²⁺ > Li⁺.     

Synthesis of garnet structured Li7+x La3Y x Zr2-x O12 (x = 0–0.4) by modified sol–gel method

Preparation of lithium garnet Li₇La₃Zr₂O₁₂ (LLZ) in cubic phase by solid state method requires high temperature sintering around 1,200 °C for 36 h in Al₂O₃ crucible with intermittent grinding. Synthesis of LLZ in cubic phase at lower temperatures by wet chemical methods was reported earlier, however that decompose at high temperature around 850 °C. In this work we report the systematic studies on synthesis of garnet structured electrolytes by modified sol–gel method by the simultaneous substitution of Li⁺ and Y³⁺ for Zr⁴⁺ according to the formulae Li_7+x La₃Y _x Zr_2-x O₁₂ (x = 0, 0.1, 0.2, 0.3 and 0.4). The present investigation revealed that the cubic garnet phase is obtained at much lower temperature for Li₇La₃Zr₂O₁₂ and the simultaneous increase of both Li⁺ and Y³⁺ in Li_7+x La₃Y _x Zr_2-x O₁₂ requires slightly higher sintering temperatures for the formation of cubic garnet phase. SEM micrographs of the Li_7+x La₃Y _x Zr_2-x O₁₂ (x = 0, 0.1, 0.2, 0.3 and 0.4) annealed at minimum sintering temperature required for the formation of cubic garnet phase revealed the increase in grain size and relatively dense structure with increase of x in Li_7+x La₃Y _x Zr_2-x O₁₂.     

Suppression of charge imbalance via Li+-Mn4+ co-incorporated Sr2YSbO6 red phosphors for warm w-LEDs

Mn⁴⁺-activated double perovskite phosphors with composition diversity have presented excellent luminescent performances. However, the charge imbalance between Mn⁴⁺ and matrix cations would increase non-radiative recombination and reduce the structural stability. Here, novel high-efficiency stable Li⁺/Mn⁴⁺ co-incorporated Sr₂YSbO₆ red phosphors are successfully synthesized via a solid-state reaction method for warm w-LEDs, where the Li⁺ ions have the effect of charge balance for Sr₂YSbO₆:Mn⁴⁺ and reduce the non-radiative energy transfer among Mn⁴⁺ ions. It is demonstrated that the substitution of Li⁺–Mn⁴⁺ pairs for Sb⁵⁺ can enhance the bonding with low-shifted diffraction peaks and high emission intensity, and prolong the decay lifetime, compared with those of Mn⁴⁺ single-doped ones. Impressively, the thermal stability is enhanced to 89.72% from 84.61% at the original value of 303 K. Finally, a w-LED device based on the optimal phosphor Sr₂YSbO₆:0.01Mn⁴⁺/0.01Li⁺ red component exhibits a correlated color temperature of 4487 K and color rendering index of 80.2. Therefore, the incorporated Li⁺ ions serve as both charge compensator and co-activator in Mn⁴⁺-activated double perovskite phosphors with the aim of high luminescent performance and thermal stability.     

Quantum chemical study of the interaction between selenium analog of methimazole as an anti-thyroid drug and metal cations

Energetic and structural properties of complexes formed from interaction between selenium analog of methimazole (MSeI) as an anti-thyroid drug and M^z+ (Li⁺, Na⁺, K⁺, Be²⁺, Mg²⁺ and Ca²⁺) cations have been investigated using B3LYP, M062X, PBE1PBE, and MP2 methods with 6-311++G(d,p) and 6-311++G(2d,2p) basis sets. Two planar and perpendicular complexes were predicted from interaction of MSeI and M^z+ cations. From the Gibbs free energy difference between the planar and perpendicular forms of MSeI–M^z+ complexes, it is found that the perpendicular forms are the predominant ones. In addition, the comparison of interaction energies shows that the order of energies increases in the following order: K⁺ < Na⁺ < Li⁺ < Ca²⁺ < Mg²⁺ < Be²⁺. The results of natural bond orbital analysis showed that the charge transfer occurs from MSeI to metal cations. The atom in molecule analysis shows that the charge density and its Laplacian at the Se–M^z+ bond critical point of the MSeI–M²⁺ complexes are greater than the MSeI–M¹⁺ ones. Also, it was revealed that the Se–M^z+ interactions in perpendicular complexes of alkali and alkaline metal cations are electrostatic and partially covalent in nature, respectively.     

A new Schiff base fluorescent indicator for the detection of Mg<Superscript>2+</Superscript> and its application to real samples

A new Schiff base fluorescence probe, 3-Allylsalicylaldehyde salicylhydrazone (L), for Mg²⁺ was designed and synthesized. The fluorescence of the sensor L was enhanced remarkably by Mg²⁺ with 2:1 binding ratio, and the binding constant was determined to be 1.02 × 10⁷ M^?1. Probe L had high sensitivity for Mg²⁺ in a solution of DMF/water (4:1, v/v, pH 7.5), and the detection limit was 4.88 × 10^?8 mol/L. Common coexistent metal ions, such as K⁺, Na⁺, Ag⁺, Ca²⁺, Zn²⁺, Ba²⁺, Bi²⁺, Cu²⁺, Ni²⁺, Hg²⁺, Fe³⁺ , and Al³⁺, showed little or no interference on the detection of Mg²⁺ in solution. The fluorescence probe L, which was successfully used for the determination of trace Mg(II) in real samples, was shown to be promising for liquid-phase extraction coupled with fluorescence spectra.     

The electrochemical performance of sodium-ion-modified spinel LiMn2O4 used for lithium-ion batteries

The spinel LiMn₂O₄ cathode material has been considered as one of the most potential cathode active materials for rechargeable lithium ion batteries. The sodium-doped LiMn₂O₄ is synthesized by solid-state reaction. The X-ray diffraction analysis reveals that the Li_1?x Na _x Mn₂O₄ (0?≤?x?≤?0.01) exhibits a single phase with cubic spinel structure. The particles of the doped samples exhibit better crystallinity and uniform distribution. The diffusion coefficient of the Li_0.99Na_0.01Mn₂O₄ sample is 2.45?×?10^?10 cm^?2 s^?1 and 3.74?×?10^?10 cm^?2 s^?1, which is much higher than that of the undoped spinel LiMn₂O₄ sample, indicating the Na⁺-ion doping is favorable to lithium ion migration in the spinel structure. The galvanostatic charge–discharge results show that the Na⁺-ion doping could improve cycling performance and rate capability, which is mainly due to the higher ion diffusion coefficient and more stable spinel structure.