Room temperature photoluminescence of amorphous BaxSr1−xTiO3 doped with chromium

ABO₃ amorphous materials, such as BaTiO₃ (BT), SrTiO₃ (ST), PbTiO₃ (PT), and Ba_xSr_1−xTiO₃ (BST) have recently attracted a good deal of attention due to their ferroelectric and electro-optical properties. Intense photoluminescence at room temperature was observed in amorphous titanate doped with chromium (Ba_xSr_1−xTi_1−yCr_yO₃) prepared by the polymeric precursor method. Results indicated that substantial luminescence at room temperature was achieved with the addition of small Cr contents to amorphous Ba_xSr_1−xTi_1−yCr_yO₃. Further addition of Cr or crystallization were deleterious to the intensity of the luminescent peak obtained for excitation using λ=488.0 nm.     

Temperature and composition dependent structural investigation of the defect perovskite series Sr1−xTi1−2xNb2xO3, 0≤x≤0.2

The crystal structure of the defect perovskite series Sr_1−xTi_1−2xNb_2xO₃ has been investigated over a range of temperatures using high-resolution synchrotron X-ray diffraction, neutron diffraction and electron diffraction. Three distinct regions were observed: 0<x≤0.125 was a solid solution of Sr_1−xTi_1−2xNb_2xO₃ with minor SrTiO₃ intergrowth, 0.125<x≤0.2 was a pure Sr_1−xTi_1−2xNb_2xO₃ solid solution adopting the cubic perovskite type structure (Pm3¯m) and for x>0.2 Sr_0.8Ti_0.6Nb_0.4O₃ and Sr₃TiNb₄O₁₅ formed a two phase region. The cubic structure for Sr_0.8Ti_0.6Nb_0.4O₃ was stable over the temperature range 90-1248 K and the thermal expansion co-efficient was determined to be 8.72(9)×10⁻⁶ K⁻¹. Electron diffraction studies revealed diffuse scattering due to local scale Ti/Nb displacements and slightly enhanced octahedral rotations that did not lead to long range order. The octahedral rotations were observed to ‘lock-in’ at temperatures below ∼75 K resulting in a tetragonal structure (I4/mcm) with anti-phase octahedral tilting about the c-axis.     

Luminescent and structural properties of the series Ba6−xEuxTi2+xTa8−xO30 and Ba4−yKyEu2Ti4−yTa6+yO30

The series Ba_6−xEu_xTi_2+xTa_8−xO₃₀ and Ba_4−yK_yEu₂Ti_4−yTa_6+yO₃₀ have been synthesized at 1400°C in air. They exhibit efficient excitation at about 400 nm and typical emission of Eu³⁺ at about 580-620 nm, form solid solutions within 0.0?x?2.0 and 0?y?4 respectively, and crystallized in P4/mbm at room temperature with Eu atoms occupied at centrosymmetric site (0, 0, 0). Their conductivity is very low (2.8×10⁻⁶ Ω⁻¹ cm⁻¹ at 740°C for Ba₆Ti₂Ta₈O₃₀).     

Crystal structure and electrical conductivity of lanthanum-calcium chromites-titanates La1−xCaxCr1−yTiyO3−δ (x=0-1, y=0-1)

Five series of perovskite-type compounds in the system La_1−xCa_xCr_1−yTi_yO₃ with the nominal compositions y=0, x=0-0.5; y=0.2, x=0.2-0.8; y=0.5, x=0.5-1.0; y=0.8, x=0.6-1.0 and y=1, x=0.8-1 were synthesized by a ceramic technique in air (final heating 1350 °C). On the basis of the X-ray analysis of the samples with (Ca/Ti)?1, the phase diagram of the CaTiO₃-LaCr^IIIO₃-CaCr^IVO₃ quasi-ternary system was constructed. Extended solid solution with a wide homogeneity range is formed in the quasi-ternary system CaCr^IVO₃-CaTiO₃-LaCr^IIIO₃. The solid solution La_{(1−x′−y)}Ca_(x′+y)Cr^IV_x′Cr^III_{(1−x′−y)}Ti_yO₃ exists by up to 0.6-0.7 mol fractions of CaCr^IVO₃ (x^′<0.6-0.7) at the experimental conditions. The crystal structure of the compounds is orthorhombic in the space group Pbnm at room temperature. The lattice parameters and the average interatomic distances of the samples within the solid solution ranges decrease uniformly with increasing Ca content. Outside the quasi-ternary system, the nominal compositions La_0.1Ca_0.9TiO₃, La_0.2Ca_0.8TiO₃, La_0.4Ca_0.6Cr_0.2Ti_0.8O₃ and La_0.3Ca_0.7Cr_0.2Ti_0.8O₃ in the system La_1−xCa_xCr_1−yTi_yO₃ were found as single phases with an orthorhombic structure. In the temperature range between 850 and 1000 °C, the synthesized single-phase compositions are stable at pO₂=6×10⁻¹⁶-0.21×10⁵ Pa. Oxygen stoichiometry and electrical conductivity of the separate compounds were investigated as functions of temperature and oxygen partial pressure. The chemical stability of these oxides with respect to oxygen release during thermal dissociation decreases with increasing Ca-content. At 900 °C and oxygen partial pressure 1×10⁻¹⁵-0.21×10⁵ Pa, the compounds with x>y (acceptor doped) are p-type semiconductors and those with x<y (donor doped) and x=y are n-type semiconductors. The type and level of electrical conductivity are functions of the concentration ratios of cations occupying the B-sites of the perovskite structures: [Cr³⁺]/[Cr⁴⁺] and [Ti⁴⁺]/[Ti³⁺]. The maximum electrical conductivity at 900 °C and pO₂=10⁻¹⁵ Pa was found for the composition La_0.1Ca_0.9TiO₃ (near 50 S/cm) and in air at 900 °C for La_0.5Ca_0.5CrO₃ (close to 100 S/cm).     

Hydrothermal synthesis, characterization and composition-dependent magnetic properties of LaFe1−xCrxO3 system (0≤x≤1)

Hydrothermal synthesis, characterization and magnetic properties of a series of ABO₃-perovskites LaFe_1−xCr_xO₃ (0≤x≤1) are reported. The alkalinity in initial reaction mixtures plays a critical role in controlling the designed stoichiometry of the final compositions. Their magnetic properties are strongly dependent on the compositions and a maximum magnetic moment is found for the sample at x=0.5. Weak ferromagnetic interaction observed for the samples from x=0 to 0.9 arises from the presence of Fe-O-Fe antisymmetric exchange and Fe-O-Cr superexchange interaction. The weak ferromagnetism as well as the linear variation of the lattice parameters implies the possible random distribution of Fe and Cr ions in B sites of the perovskites. The evolution of magnetic ordering transition temperatures has a close relationship with substituent ratios, for the competition of antiferromagnetism and ferromagnetism. The saturated magnetic moment shows a great improvement compared with that for the samples synthesized by solid state method.     

Structural and dielectric/ferroelectric properties of (La1−xNdx)2Ti2O7 synthesized by sol-gel route

A series of compounds with the general formula (La_1−xNd_x)₂Ti₂O₇ (0.0≤x≤1.0) has been prepared by the sol-gel method. The decomposition of the gel was characterized by thermo-gravimetric analysis coupled to mass spectrometry, indicating the reaction is achieved above 850 °C. The lattice parameters versus x show an expected decrease in the a and b parameters while c and the β angle remain almost unchanged with respect to the monoclinic symmetry conserved for the full solid solution. Dielectric, piezoelectric and ferroelectric properties were measured on the entire series.     

Mechanochemical-thermal preparation and structural studies of mullite-type Bi2(GaxAl1−x)4O9 solid solutions

A series of Bi₂(Ga_xAl_1−x)₄O₉ solid solutions (0≤x≤1), prepared by mechanochemical processing of Bi₂O₃/Ga₂O₃/Al₂O₃ mixtures and subsequent annealing, was investigated by XRD, EDX, and ²⁷Al MAS NMR. The structure of the Bi₂(Ga_xAl_1−x)₄O₉ solid solutions is found to be orthorhombic, space group Pbam (No. 55). The lattice parameters of the Bi₂(Ga_xAl_1−x)₄O₉ series increase linearly with increasing gallium content. Rietveld refinement of the XRD data as well as the analysis of the ²⁷Al MAS NMR spectra show a preference of gallium cations for the tetrahedral sites in Bi₂(Ga_xAl_1−x)₄O₉. As a consequence, this leads to a far from random distribution of Al and Ga cations across the whole series of solid solutions.     

Synthesis and optical absorption property of the Zn2TixSn1−xO4 (0?x?1) solid solutions

Zn₂Ti_xSn_1−xO₄ (0?x?1) solid solutions with an inverse spinel structure (Fd3m) were synthesized by solid-state reactions at 1300°C of the stoichiometric mixtures of ZnO, TiO₂ and SnO₂. X-ray diffraction, thermogravimetric and differential thermal analyses, scanning electron microscopy, transmission electron microscopy and BET specific surface area measurements were used to gain insights into the solid-state reactions and phase transformation of the system. Optical absorption property of the Zn₂Ti_xSn_1−xO₄ (0?x?1) solid solutions was studied with the ultraviolet-visible diffuse reflectance spectroscopy (UV-Vis DRS). The Zn₂Ti_xSn_1−xO₄ (0?x?1) solid solutions showed optical absorptions of the semiconductors in the near ultraviolet region; the adsorption band shifts with the composition of the solid solution.     

Structural characterization and physical properties of the system La1.33LixCrxTi2−xO6

New phases which arise from partial substitution of Ti⁴⁺ by Cr³⁺ and Li⁺ of the compound La_2/3TiO₃ have been obtained, giving rise to the series La_1.33Li_xCr_xTi_2−xO₆ (x=0.66, 0.55 and 0.44). These phases adopt a perovskite-type structure as deduced from their structural characterization. Rietveld's analyses of neutron diffraction data show that it is orthorhombic (S.G. Pbnm) with ordered domains. Conductivity has been examined by complex impedance spectroscopy and it increases with increasing lithium and chromium content. These materials behave as mixed conductors with low activation energies. Magnetic susceptibility variation with temperature shows antiferromagnetic interactions at the lowest temperatures.     

Structural Study of Li1+x−yNb1−x−3yTix+4yO3 Solid Solutions

The structures of Li_1+x−yNb_1−x−3yTi_x+4yO₃ solid solutions within the so-called M-phase field in the Li₂O-Nb₂O₅-TiO₂ system were investigated using high-resolution transmission electron, microscope (HRTEM) and single-crystal X-ray diffraction. The results demonstrated that the phase field is not a solid solution but rather a homologous series of commensurate intergrowth structures with LiNbO₃-type (LN) slabs separated by single [Ti₂O₃]²⁺ corundum-type layers. The thickness of the LN slab decreases with increasing Ti-content from ∼55 to 3 atomic layers in the metastable H-Li₂Ti₃O₇ end-member. The LN slabs accommodate a wide range of Ti⁴⁺/Nb⁵⁺ substitution, and for a given homolog the distribution of Ti and Nb is not uniform across the slab. A single-crystal X-ray diffraction study of a structure composed of nine-layer LN slabs revealed preferential segregation of Ti to the slab surfaces which apparently provides partial compensation for the charge on the adjacent [Ti₂O₃]²⁺ corundum layers. The extra cations in phases with x>0 are accommodated through the formation of Li-rich Li₂MO₃-type layers in the middle of the LN slabs. The fraction of layers with extra cations increases with increasing Ti-content in the structure.     

Phase formation, crystal structures and magnetic properties of perovskite-type phases in the system La2Co1+z(MgxTi1−x)1−zO6

Perovskite-type cobaltates in the system La₂Co_1+z(Mg_xTi_1−x)_1−zO₆ were studied for z=0≤x≤0.6 and 0≤x<0.9, using X-ray and neutron powder diffraction, electron diffraction (ED), magnetic susceptibility measurements and X-ray absorption near-edge structure (XANES) spectroscopy. The samples were synthesised using the citrate route in air at 1350 °C. The space group symmetry of the structure changes from P2₁/n via Pbnm to R3¯c with both increasing Mg content and increasing Co content. The La₂Co(Mg_xTi_1−x)O₆ (z=0) compounds show anti-ferromagnetic couplings of the magnetic moments for the Co below 15 K for x=0, 0.1 and 0.2. XANES spectra show for the compositions 0≤x≤0.5 a linear decrease in the L₃/(L₃+L₂) Co-L_2,3 edge branching ratio with x, in agreement with a decrease of the average Co ion spin-state, from a high-spin to a lower-spin-state, with decreasing nominal Co²⁺ ion content.     

Thermochemistry of La0.7Sr0.3Mn1−xFexO3 solid solutions (0<x<1)

The structure, the energetics and the internal redox reactions of La_0.7Sr_0.3Fe_xMn_1−xO₃ have been studied in the complete solid solution range 0.0<x<1.0. High temperature oxide melt drop solution calorimetry was performed to determine the enthalpies of formation from binary oxides and the enthalpy of mixing. There is a noticeable change in the energetics of the solid solution near x=0.7, which is due to the growing concentration of Fe⁴⁺ at higher Fe/(Fe+Mn) ratio. The balance between different valences of the transition metals, Mn and Fe, is the main factor in determining the energetics of the La_0.70Sr_0.30Fe_xMn_1−xO₃ solid solution.     

Crystal Structure of Pseudorhombohedral InFe1−xTixO3+x/2 (x=2/3)

The structure of pseudorhombohedral-type InFe_1−xTi_xO_3−x/2 (x=2/3) was refined by Rietveld profile fitting. The crystal is a commensurate member of a series in a solution range on InFeO₃-In₂Ti₂O₇ including incommensurate structures. The structure with the unit cell of a=5.9188(1), b=10.1112(2), and c=6.3896(1) Å, β=108.018(2)°, and a space group P2₁/a is the alternate stacking of an edge-shared InO₆ octahedral layer and an Fe/Ti-O plane along c^*. Metal sites on the Fe/Ti-O plane are surrounded by four oxygen atoms on the Fe/Ti-O plane and two axial ones. Electric conductivities of the order 10⁻⁴ S/cm were observed for the samples at 1000 K, while the oxide ion transport number is almost zero as no electromotive force was detected by an oxygen concentration cell.     

Chemical stability of La1−xSrxCrO3 in oxidizing atmospheres

The single-phase region of La_1−xSr_xCrO₃ (x=0.1, 0.2, 0.3) was precisely determined as a function of temperature, P_O2 and Sr content. The powders with the nominal composition of La_1−xSr_xCrO₃ were equilibrated under various conditions, and then identified by XRD analyses. To confirm the equilibration, two independent experiments were performed for each composition observing (i) the precipitation of the second phase from a single-phase solid solution, and (ii) the formation of the single phase from the constituent oxides. Two kinds of second phases, SrCrO₄ and an unknown phase, were observed depending on the conditions. The second phases tended to appear at low temperature, in high P_O2 and with a large Sr content. The single-phase regions obtained via the two equilibration routes were in good agreement with each other. The thermodynamic calculations on the supposition of ideality of the solid solution essentially reproduced the experimental results. When this material is used as the interconnects of solid oxide fuel cells, much attention should be paid to its relatively narrow solubility range of Sr; for example, the solubility limit is approximately 0.1 under a typical cathode-side condition (1273 K, air).     

Formation, sintering, and electrical conductivity of perovskite Sm(Cr1−xMgx)O3 (0?x?0.23) prepared by the hydrazine method

The presence of SmCrO₄ is experimentally established. In Mg²⁺-substituted SmCrO₃, single-phase perovskite Sm(Cr_1−xMg_x)O₃, where x=0-0.23, are formed at ∼830°C by decomposition of Sm(Cr_1−xMg_x)O₄ which crystallizes at 530-570°C from amorphous materials prepared by the hydrazine method. Sm(Cr_1−xMg_x)O₃ solid solution powders consisting of submicrometer-size particles are sinterable; dense materials can be fabricated by sintering for 2 h at 1700°C in air. The relative densities, grain sizes, and electrical conductivities increase with increased Mg²⁺ content. Sm(Cr_0.77Mg_0.23)O₃ materials exhibit an excellent direct current electrical conductivity of 2.2×10³ S m⁻¹ at 1000°C.     

The Crystal Structures, Microstructure and Ionic Conductivity of Ba2In2O5 and Ba(InxZr1−x)O3−x/2

This paper describes the results of electron microscopy, high-temperature powder neutron diffraction, and impedance spectroscopy studies of brownmillerite-structured Ba₂In₂O₅ and perovskite structured Ba(In_xZr_1−x)O_3−x/2. The ambient temperature structure of Ba₂In₂O₅ is found to adopt Icmm symmetry, with disorder of the tetrahedrally coordinated (In³⁺) ions of the type observed previously in Sr₂Fe₂O₅. Ba₂In₂O₅ undergoes a ∼6-fold increase in its ionic conductivity over the narrow temperature range from ∼1140 K to ∼1230 K, in broad agreement with previous studies. This transition corresponds to a change from the brownmillerite structure to a cubic perovskite arrangement with disordered anions. Electron microscopy investigations showed the presence of extended defects in all the crystals analyzed. Ba(In_xZr_1−x)O_3−x/2 samples with x=0.1 to 0.9 adopt the cubic perovskite structure, with the lattice parameter increasing with x.     

Different [Bi12O14]n Columnar Structural Types in the Bi-Mo-Cr-O System: Synthesis, Structure, and Electrical Properties of the Solid Solution Bi26Mo10−xCrxO69

In order to search for new ionic conductor materials exhibiting a columnar [Bi₁₂O₁₄] structural type, the syntheses of the solid solutions Bi₂Mo_1−xCr_xO₆ and Bi₂₆Mo_10−xCr_xO₆₉ have been undertaken. Single phases were obtained for the last composition with 0≤x≤5 homogeneity range. Moreover, a new oxide with Bi₆Cr₂O₁₅ composition has been obtained from the limit nominal stoichiometries Bi₆CrO₆ and Bi₂₆Cr₁₀O₆₉. X-ray powder diffraction studies have shown that this oxide crystallizes in the orthorhombic system, space group Ccc2 or Cccm, with unit-cell parameters a=19.8986(9) Å, b=12.2756(6) Å, c=5.8868(3) Å, and V=1437.96 ų. Impedance spectroscopy measurements carried out on the representative Bi₂₆Mo₈Cr₂O₆₉ phase, showed that this material is a good oxygen ion conductor, in fact the best one belongs to the columnar structural type, with a conductivity as high as 1.7×10⁻³Scm⁻¹ at 425°C.     

Structure and photoluminescence properties of Ce-doped novel silicon-oxynitride Ba4−zMzSi8O20−3xN2x (M=Mg, Ca, Sr)

Structural and photoluminescence properties of undoped and Ce³⁺-doped novel silicon-oxynitride phosphors of Ba_4−zM_zSi₈O_20−3xN_2x (M=Mg, Sr, Ca) are reported. Single-phase solid solutions of Ba_4−zM_zSi₈O_20−3xN_2x oxynitride were synthesized by partial substitutions of 3O²⁻→2N³⁻ and Ba→M (M=Mg, Ca, Sr) in orthorhombic Ba₂Si₄O₁₀. The influences of the type of alkaline earth ions of M, the Ce³⁺ concentration on the photoluminescence properties and thermal quenching behaviors of Ba₃MSi₈O_20−3xN_2x (M=Mg, Ca, Sr, x=0.5) were investigated. Under excitation at about 330 nm, Ba₃MSi₈O_20−3xN_2x:Ce³⁺ (x=0.5) exhibits efficient blue emission centered at 400-450 nm in the range of 350-650 nm owing to the 5d→4f transition of Ce³⁺. The emission band of Ce³⁺ shifts to long wavelength by increasing the ionic size of M due to the modification of the crystal field, as well as the Ce³⁺ concentrations due to the Stokes shift and energy transfer or reabsorption of Ce³⁺ ions. Among the silicon-oxynitride phosphors of Ba₃MSi₈O_18.5N:Ce³⁺, M=Sr_0.6Ca_0.4 possesses the best thermal stability probably related to its high onset of the absorption edge of Ce³⁺.     

Crystal structure, thermal expansion and conductivity of anisotropic La1−xSrxGa1−2xMg2xO3−y (x=0.05, 0.1) single crystals

Crystal structure and anisotropy of the thermal expansion of single crystals of La_1−xSr_xGa_1−2xMg_2xO_3−y (x=0.05 and 0.1) were measured in the temperature range 300-1270 K. High-resolution X-ray powder diffraction data obtained by synchrotron experiments have been used to determine the crystal structure and thermal expansion. The room temperature structure of the crystal with x=0.05 was found to be orthorhombic (Imma, Z=4, a=7.79423(3) Å, b=5.49896(2) Å, c=5.53806(2) Å), whereas the symmetry of the x=0.1 crystal is monoclinic (I2/a, Z=4, a=7.82129(5) Å, b=5.54361(3) Å, c=5.51654(4) Å, β=90.040(1)°). The conductivity in two orthogonal directions of the crystals has been studied. Both, the conductivity and the structural data indicate three phase transitions in La_0.95Sr_0.05Ga_0.9Mg_0.1O_2.92 at 520-570 K (Imma-I2/a), 770 K (I2/a-R3c) and at 870 K (R3c-R-3c), respectively. Two transitions at 770 K (I2/a-R3c) and in the range 870-970 K (R3c-R-3c) occur in La_0.9Sr_0.1Ga_0.8Mg_0.2O_2.85.