Effect of Al Addition on Formation of Layer-Structured LiNiO2

Kinetics and formation mechanism of undoped and Al-doped LiNiO₂ from Li₂CO₃ and NiO were investigated in this study. Without the addition of Al ions, sluggish kinetics for the formation of undoped LiNiO₂ was observed. The fraction of undoped LiNiO₂ reached 50% after Li₂CO₃ and NiO reacted at 700°C for 150 min. With the addition of 25% of Al ion, the fraction of Al-doped LiNiO₂ reached 50% within 60 min at 700°C. The analysis of kinetics study indicates that the formation of undoped and Al-doped LiNiO₂ is a diffusion-controlled process. Furthermore, the rate constant determined from Jander model {[1−(1−α)^1/3]²=Kt} was significantly enhanced by the addition of Al. The activation energy for the formation of LiNiO₂ drastically decreased from 190 kJ/mole (undoped reaction) to 83 kJ/mole when 25% Al was added. The enhancement of LiNiO₂ formation by Al doping is attributed to the structure resemblance between αLiAlO₂ and LiNiO₂. αLiAlO₂ acts as the seeding material which provides nucleation sites for the growth of LiNiO₂.     

Ni/TiO2-SiO2上光催化重整葡萄糖以低CO选择性制H2（英文）

Nano-sized Ni particles on TiO2-SiO2 were synthesized by the two methods of photo-assisted deposition(PAD) and impregnation.H2,which is a promising energy carrier,with a low CO concentration was produced by the photocatalytic reforming of glucose(a model biomass) on the Ni/TiO2-SiO2 catalyst.The supported Ni enhanced the rate of H2 production while it suppressed CO selectivity.The catalysts were characterized by X-ray diffraction,X-ray absorption fine structure,transmission electron microscope,and nitrogen adsorption analysis.Both H2 production and CO selectivity were strongly dependent on the preparation method,and PAD-Ni/TiO2-SiO2 was the better catalyst for H2 production with the lowest CO concentration.     

CuO-SiO_2和Cu_2O-SiO_2薄膜的制备及其光学性能

以CuSO_4·5H_2O和正硅酸乙酯为前驱体,配制了稳定透明的Cu~(2+)-SiO_2复合溶胶电解液。采用电化学-溶胶凝胶方法,在恒电位-0.9 V下得到Cu-SiO_2复合膜,该复合薄膜分别在250和450℃的热处理后得到Cu_2O-SiO_2和CuO-SiO_2复合薄膜。采用XRD、SEM/EDX和台阶仪表征了复合薄膜的组成、形貌和厚度;采用紫外-可见光谱和Z扫描技术研究了复合薄膜的线性和三阶非线性光学性能。结果表明Cu2O-SiO_2和CuO-SiO_2复合薄膜中的Cu含量、Cu的形态(如Cu_2O、CuO)及Cu_2O或CuO颗粒大小影响薄膜的光学带隙和三阶非线性光学性能,2种薄膜的光学带隙分别是2.67和2.54 eV,三阶非线性极化率χ(3)分别为2.31×10~(-6)和1.36×10~(-6) esu。     

CuO-SiO2和Cu2O-SiO2薄膜的制备及其光学性能

以CuSO₄·5H₂O和正硅酸乙酯为前驱体,配制了稳定透明的Cu²⁺-SiO₂复合溶胶电解液。采用电化学-溶胶凝胶方法,在恒电位-0.9 V下得到Cu-SiO₂复合膜,该复合薄膜分别在250和450℃的热处理后得到Cu₂O-SiO₂和CuO-SiO₂复合薄膜。采用XRD、SEM/EDX和台阶仪表征了复合薄膜的组成、形貌和厚度;采用紫外-可见光谱和Z扫描技术研究了复合薄膜的线性和三阶非线性光学性能。结果表明Cu₂O-SiO₂和CuO-SiO₂复合薄膜中的Cu含量、Cu的形态（如Cu₂O、CuO）及Cu₂O或CuO颗粒大小影响薄膜的光学带隙和三阶非线性光学性能,2种薄膜的光学带隙分别是2.67和2.54 eV,三阶非线性极化率χ^（3）分别为2.31×10^-6和1.36×10^-6 esu。     

Soluble Ni alkoxides based on dimethylaminoisopropoxide ligands: molecular structure of [Li(PrOH)Ni (η-OR)2Cl]2 and of cis-NiCl2(ROH)2 (R = CHMeCH2NMe2)

Various routes to Ni^II aminoalkoxides have been investigated. A nickel isopropoxide derivative 1 was prepared by anodic dissolution of the metal in the presence of LiCl as electrolyte. Alcoholysis reactions of 1 with 1-dimethylamino-2-propanol afforded the homoleptic nickel(II) aminoalkoxide 2 together with a NiLi species 3. 2 was also obtained by metathesis reactions between sodium alkoxide and the nickel hexammine complex whereas the reaction between the latter and the aminoalcohol led to an halide solvate, cis-NiCl₂(η²-ROH)₂, 4. The various compounds were characterized by elemental analysis, FT-IR and UV-vis spectroscopies as well as by X-ray diffraction for 3 and 4. 3 corresponds to [Li(PrⁱOH)Ni(η²-OCHMeCH₂NMe₂)Cl]₂ and the overall structure can be seen as two [Ni(η²-OCHMeCH₂NMe₂)₂Cl]⁻ moieties assembled by Li(PrⁱOH)⁺. The lithium atom is 4-coordinate due to its interaction with the oxygen atoms of the aminoalkoxide ligands. Nickel is 5-coordinate with a distorted tetragonal pyramidal stereochemistry, one nitrogen being in the apical position. The metal displays a distorted octahedral surrounding for the NiCl₂ adduct 4. The bond distances vary in the order NiOR < NiN ≈ NiO(H)R < NiCl for 3 and 4. The various compounds (except 1) are soluble in organic media.     

Soluble Ni alkoxides based on dimethylaminoisopropoxide ligands: molecular structure of [Li(PrOH)Ni (η-OR)2Cl]2 and of cis-NiCl2(ROH)2 (R = CHMeCH2NMe2)

Various routes to Ni^II aminoalkoxides have been investigated. A nickel isopropoxide derivative 1 was prepared by anodic dissolution of the metal in the presence of LiCl as electrolyte. Alcoholysis reactions of 1 with 1-dimethylamino-2-propanol afforded the homoleptic nickel(II) aminoalkoxide 2 together with a Ni---Li species 3. 2 was also obtained by metathesis reactions between sodium alkoxide and the nickel hexammine complex whereas the reaction between the latter and the aminoalcohol led to an halide solvate, cis-NiCl₂(η²-ROH)₂, 4. The various compounds were characterized by elemental analysis, FT-IR and UV-vis spectroscopies as well as by X-ray diffraction for 3 and 4. 3 corresponds to [Li(PrⁱOH)Ni(η²-OCHMeCH₂NMe₂)Cl]₂ and the overall structure can be seen as two [Ni(η²-OCHMeCH₂NMe₂)₂Cl]⁻ moieties assembled by Li(PrⁱOH)⁺. The lithium atom is 4-coordinate due to its interaction with the oxygen atoms of the aminoalkoxide ligands. Nickel is 5-coordinate with a distorted tetragonal pyramidal stereochemistry, one nitrogen being in the apical position. The metal displays a distorted octahedral surrounding for the NiCl₂ adduct 4. The bond distances vary in the order Ni---OR < Ni---N ≈ Ni---O(H)R < Ni---Cl for 3 and 4. The various compounds (except 1) are soluble in organic media.     

Conductivity and Structural Investigations in Lacunary Pb6Ca2Li2(PO4)6 Apatite

Prismatic crystals of Pb₆Li₂Ca₂(PO₄)₆ were obtained by solid-state reaction. They were characterized by IR spectroscopy and chemical analyses. The structure as determined by X-ray diffraction study on single crystal revealed that the compound is isostructural to the hexagonal phase Pb₈Na₂(PO₄)₆. Crystal data for Pb₆Li₂Ca₂(PO₄)₆: space group P63/m (No. 176), a=b=9.6790(15) Å, c=7.1130(7), Z=1, R=0.039. In the compound, lithium was found to preferentially occupy the site (I) and the structure is stabilized by interactions between electron lone pairs of lead (II) ions. Electrical conductivity measured in a wide range of temperature is governed by a hopping mechanism of Li ions in tunnels.     

高效锂离子筛吸附剂MnO2•0.5H2O的软化学合成及吸附性能研究

以MnCl₂•4H₂O, LiOH•H₂O等试剂为初始原料, 采用溶胶-凝胶、水热处理、固化等软化学合成步骤制备了锂离子筛前驱体Li_1.6Mn_1.6O₄, 并经稀盐酸抽锂后得到了高选择性锂离子筛吸附剂MnO₂•0.5H₂O. 着重对合成过程中锂锰比, 氧化剂用量等因素影响进行了探讨, 并对所制备吸附剂的吸附性能进行了研究. 结果表明, 经软化学合成步骤制备的锂离子筛对Li^＋有良好的吸附量和选择性, 在未来从海水、卤水等液态锂资源富集或提取锂的应用中具有很大的潜力.     

一个新颖的三核镍配合物[Ni3(C13H9N2O)5(CH3OH)(CH3CH2OH)]Cl的合成、晶体结构及性质研究

在甲醇-乙醇混合溶剂中, 含有N, O给体的二齿配体2-(2-羟苯基)苯并咪唑与NiCl2•6H2O在常温下反应合成得到标题化合物, 采用元素分析、红外光谱、紫外光谱、热分析以及X射线单晶衍射法对其进行了组成和结构表征. 结果表明该化合物为三斜晶系, 空间群P-1, 晶胞参数: a＝1.2046(2) nm, b＝1.4891(3) nm, c＝2.1342(4) nm, α＝96.787(3)°, β＝104.862(3)°, γ＝99.993(3)°, V＝3.5904(12) nm3, Z＝2, Dc＝1.349 g/cm3, F(000)＝1516, GOF＝1.008, R1＝0.0583, wR2＝0.1455 [I＞2σ(I)]. 在标题化合物的晶体结构中, 晶体学不对称的三个配位中心Ni(II)原子配位环境各不相同, 五个配体提供的五个氧配位基中有四个起着桥联的作用, 形成了一个新颖的V型金属簇状化合物. 变温磁化率研究表明标题化合物在整体上表现为弱的反铁磁性耦合作用.     

水洗和回烧工艺对高镍三元材料LiNi0.88Co0.07Al0.05O2微观结构及电化学性能的影响

以镍钴氢氧化物、异丙醇铝为原料,采用水解法合成三元前驱体Ni_(0.88)Co_(0.07)Al_(0.05)O_2,再与锂盐混合烧结得到正极材料(TEM)、X射线光电子能谱(XPS)、能量色散X射线谱(EDS)和恒电流充放电测试等对样品的晶体结构、微观形貌、元素价态以及电化学性能进行表征。研究表明,料液比1∶25、水洗3次、600℃回烧2 h合成的LiNi_(0.88)Co_(0.07)Al_(0.05)O_2具有较优的综合电化学性能,其在0.2C的放电比容量达207.6 mAh·g~(-1),首次充放电效率为84.8%,1C放电比容量为192.0 mAh·g~(-1),循环100周后,材料的放电比容量仍有148.0 mAh·g~(-1),容量保持率达到77.1%。     

NMR and FT-IR Investigation of Spinel LiMn2O4 Cathode Prepared by the Tartaric Acid Gel Process

The structure of the lithium manganese tartrate precursor and the synthesis mechanism of LiMn₂O₄ were investigated by FT-IR, NMR, TG/DSC, and XRD in this study. The results of FT-IR and ⁷Li and ¹³C NMR measurements revealed that lithium ions bond with carboxylic acid ligands and the O–H stretching modes of tartaric acid. Manganese ion bonds only with carboxylic acid. Lithium and manganese ions were trapped homogeneously on an atomic scale throughout the precursor. Such a structure eliminates the need for long-range diffusion during the formation of lithium manganese oxides. Therefore, spinel LiMn₂O₄ was synthesized at temperatures as low as 300°C. In this work, the electrochemical properties of Li/Li_xMn₂O₄ were studied. It is clear that the discharge curves exhibit two pseudo plateaus as the LiMn₂O₄ is fired to higher temperatures. The discharge capacity of LiMn₂O₄ increases from 84 to 117 mAh/g as the calcination temperature increases from 300 to 500°C. The LiMn₂O₄ powders calcined at low temperatures with a high specific surface area and an average valence of manganese exhibit a better cycle life.     

Fe（C5H4-CH2-Trp-OMe）2的合成、晶体结构及金属离子识别性能

摘要： 以优化的两步一锅反应法合成了生物金属有机化合物Fe（C₅H₄-CH₂-Trp-OMe）₂（FcL）,通过NMR、HRMS及IR等对其结构进行了表征,利用X射线单晶衍射测定了分子结构。循环伏安法研究表明FcL在0.00~0.90 V电位范围内,给出一稳定的、形态良好的氧化还原峰,这归于化合物中Fc/Fc⁺电对的氧化还原过程。电化学金属离子识别研究显示FcL在过渡金属离子Zn²⁺和Cu²⁺的存在下,导致了配体Fc/Fc⁺式量电位的显著阳极移动,其△E^0''对Zn²⁺和Cu²⁺分别为342和335 mV,表明了FcL对Zn²⁺和Cu²⁺具有良好的识别能力。     

Fe(C_5H_4-CH_2-Trp-OMe)_2的合成、晶体结构及金属离子识别性能

以优化的两步一锅反应法合成了生物金属有机化合物Fe(C_5H_4-CH_2-Trp-OMe)2(Fc L),通过NMR、HRMS及IR等对其结构进行了表征,利用X射线单晶衍射测定了分子结构。循环伏安法研究表明Fc L在0.00~0.90 V电位范围内,给出一稳定的、形态良好的氧化还原峰,这归于化合物中Fc/Fc+电对的氧化还原过程。电化学金属离子识别研究显示FcL在过渡金属离子Zn~(2+)和Cu~(2+)的存在下,导致了配体Fc/Fc+式量电位的显著阳极移动,其ΔE0′对Zn~(2+)和Cu~(2+)分别为342和335 m V,表明了Fc L对Zn~(2+)和Cu~(2+)具有良好的识别能力。     

以吡啶为配体的镍配合物[Ni(py)3(H2O)3](1,5-nds)的合成、晶体结构及性质

采用缓慢蒸发法,在水溶剂中合成了含氮配体单核Ni(Ⅱ)配合物[Ni(py)3(H2O)3](1,5-nds)(py=pyridine,1,5-nds=1,5-萘二磺酸根离子)。采用X射线单晶衍射、红外光谱、热分析和紫外可见光谱等方法对配合物进行了表征。X射线单晶衍射表征结果表明,该配合物晶体属于单斜晶系,空间群为C2/c。晶体学参数:a=1.569 46(17)nm,b=1.219 95(12)nm,c=1.454 71(16)nm,β=14.547 1(16)°,V=2.765 1(5)nm3,Z=4。考察了该配合物的磁性和荧光性质。     

磷化镍/介孔TiO_2催化剂的制备及其催化加氢脱硫性能

以介孔TiO2(m-TiO2)为载体,采用程序升温还原法制备了Ni2P/m-TiO2催化剂,考察了不同起始Ni/P摩尔比及活性组分负载量对该催化剂结构及其催化加氢脱硫(HDS)性能的影响.结果表明,当Ni/P摩尔比为1.25时,活性组分以Ni2P为主,催化剂的最佳Ni负载量为10%.采用X射线衍射、低温N2吸附-脱附、场发射扫描电镜和程序升温还原等技术表征了m-TiO2及其它不同载体负载的Ni2P催化剂.结果表明,高结晶度m-TiO2载体使Ni和P物种的还原温度大幅度降低,在450～600oC还原制得的Ni2P/m-TiO2催化剂的结构参数基本一致,比表面积均为90m2/g左右,具有很高的热稳定性和对二苯并噻吩的HDS催化性能.在相同的反应条件下,m-TiO2负载的Ni2P催化剂HDS性能最好,各载体负载的Ni2P催化剂活性大小顺序为Ni2P/m-TiO2Ni2P/SiO2Ni2P/P25.     

水解法制备的掺铁二氧化钛超微粉的热分析、晶粒生长和结构相变

研究了用四氯化钛水解制备的纯二氧化钛和分步沉淀,共沉淀方式制备的掺铁二氧化钛的热分解状况,品化过程。采用Ｘ射线衍射和Ｖｏｉｇｔ单峰分析法计算了这三种样品在各个燃烧温度下的晶体晶粒度。结果表明,四氯化钛水争方法得到的二氧化钛粉为无定形,无定形博物经钛加热晶化过程是一个持续的过程,并没有以往文献中所报道的明显的晶化温度和晶化放热峰。应用非晶物质晶化晶核生长速率方程了晶粒生长活化能并且进行了讨论。     

以吡啶为配体的镍配合物[Ni(py)3(H2O)3] (1, 5-nds)的合成、晶体结构及性质研究

采用缓慢蒸发法, 在水溶剂中合成了含氮配体单核Ni(Ⅱ)配合物[Ni(py)₃(H₂O)₃] (1, 5-nds)(py=pyridine, 1, 5-nds=1, 5-萘二磺酸根离子)。采用X射线单晶衍射、红外光谱、热分析和紫外可见光谱等方法对配合物进行了表征。X射线单晶衍射表征结果表 明, 该配合物晶体属于单斜晶系, 空间群为C2/c。晶体学参数:a=1.569 46(17) nm, b=1.219 95(12) nm, c=1.454 71(16) nm, β=14.547 1(16)°, V=2.765 1(5) nm³, Z=4。考察了该配合物的磁性和荧光性质。     

Influence of Grain Size, Oxygen Stoichiometry, and Synthesis Conditions on the γ-Fe2O3 Vacancies Ordering and Lattice Parameters

The soft chemistry method has been used to synthesize γ-Fe₂O₃ nanoparticles: various synthesis temperature were applied to obtain nanometric powders with crystallite size in the 9-14 nm range. Powders were characterized by X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectrophotometry, surface area measurements, and electron microscopy (TEM, SEM). It is clearly shown that these nanometric powders are very well crystallized as indicated by XRD and IR spectra which present substructural bands attributed to vacancies ordering (P4₁32). Based on these model materials and in the crystallite size range studied here, cell parameter appears to be not linked to crystallite size. It rather depends both on hydroxide adsorption and chemical composition.     

梯度包覆镍酸锂材料Li[Ni0.92Co0.04Mn0.04]O2的合成与研究

采用浓度梯度加料的方式,首先沉淀制备了核为Ni(OH)2、壳为镍钴锰氢氧化物浓度梯度包覆的复合前驱体,然后配锂高温焙烧,合成了梯度包覆的镍酸锂复合正极材料Li[Ni0.92Co0.04Mn0.04]O2。采用X射线衍射(XRD)、扫描电镜(SEM)、恒电流充放电测试等方法对材料的结构、表观形貌及电化学性能进行了表征。结果表明,该材料具有良好的六方单相层状α-NaFeO2结构,呈类球型状。切面元素线扫描显示该材料的包覆壳层中主要金属元素呈梯度变化。同时该新型梯度包覆的镍酸锂复合正极材料表现出了优越的电化学性能:在25℃下,2.8~4.3 V充放电范围,0.1C首次放电比容量可达198.3 mAh.g-1,循环40次容量保持96.8%;1C和2C倍率下放电比容量可达175 mAh.g-1和165.1 mAh.g-1。55℃下,该材料首次放电比容量可达236.1 mAh.g-1,循环40次容量仍能保持77.5%。