较细ZnS:Mn/PVP纳米纤维的制备及表征

采用静电纺丝的方法制备了ZnS:Mn/Polyvinylpyrrolidone复合纳米纤维.使用的溶剂为水、乙醇及DMF(N,N-Dimediylfommnide),的使用有助于制备较细的纤维,电纺溶液中随着聚合物PVP浓度降低,纤维的直径变小,当PVP质量分数为6.6%时,纤维的直径是80 nm,通过荧光显微镜和荧光...     

YF3:Eu3+纳米纤维/高分子复合纳米纤维的制备与表征

采用静电纺丝技术制备了Y2O3:Eu3+纳米纤维,使用NH4HF2为氟化剂,经双坩埚法氟化和脱氨后得到YF3:Eu3+纳米纤维,再采用静电纺丝技术制备了YF3:Eu3+纳米纤维/PVP复合纳米纤维. XRD分析表明,立方相的Y2O3:Eu3+氟化后,得到了正交相的YF3:Eu3+纳米纤维,空间群为Pnma;YF3:Eu3+纳米纤维/PVP复合纳米纤维具有明显的YF3:Eu3+的衍射峰. SEM分析表明,YF3:Eu3+纳米纤维与YF3:Eu3+纳米纤维/PVP复合纳米纤维的直径分别为91±11 nm、319±43 nm,表面光滑. 用Shapiro-Wilk方法检验,纤维直径属于正态分布. 荧光光谱分析表明,YF3:Eu3+纳米纤维和YF3:Eu3+纳米纤维/PVP复合纳米纤维的最强发射峰均位于588 nm和595 nm,属于Eu3+的5D0→7F1跃迁,表明Eu3+占据YF3基质中Y3+晶格点的C2对称格位. PVP对YF3:Eu3+发光峰位没有影响,但发光强度降低;YF3:Eu3+的含量与YF3:Eu3+纳米纤维/PVP复合纳米纤维的发光强度成线性关系.     

ZnS:Mn/ZnS量子点在DNA定量分析中的应用

以巯基乙酸为稳定剂,采用成核掺杂的方法在水溶液中一步制备得到具有核壳结构的ZnS:Mn/ZnS量子点.研究了荧光、室温磷光产生的机理.基于DNA对量子点发光的增强效应,以ZnS:Mn/ZnS量子点作为标记探针建立了测定DNA的荧光、室温磷光的分析方法.考察了量子点浓度、EDC/NHS用量和反应时间等条件对DNA测定的影响.结果表明,在最佳测定条件下,荧光、室温磷光两种分析方法测定小牛胸腺DNA的线性区间均为50 ～600 μg/L,检出限分别为39.6、28.5 μg/L,回收率分别为98% ～ 104%、99%～101%,25次重复测定300 μg/L ctDNA的相对标准偏差分别为3.1%、2.3%.该方法简单、安全、灵敏度高.     

ZnS:Mn/ZnS量子点在DNA定量分析中的应用

以巯基乙酸为稳定剂,采用成核掺杂的方法在水溶液中一步制备得到具有核壳结构的ZnS:Mn/ZnS量子点.研究了荧光、室温磷光产生的机理.基于DNA对量子点发光的增强效应,以ZnS:Mn/ZnS量子点作为标记探针建立了测定DNA的荧光、室温磷光的分析方法.考察了量子点浓度、EDC/NHS用量和反应时间等条件对DNA测定的影...     

纳米BaFe12O19纤维的电纺制备及磁性研究

以PVP的乙酸溶液为助纺剂,采用静电纺丝技术制得了纳米BaFe12O19纤维,利用XRD和EDS对样品的物相和成分进行了分析,利用SEM和TEM对样品形貌和粒径进行了表征,并利用振动样品磁强计(VSM)对样品进行了磁性能研究.结果表明,BaFe12O19/PVP复合纤维经过800℃煅烧后,制得了纯净的BaFe12O19纳米纤维,纤维平均直径为150 nm,呈现出多晶结构,矫顽力为4 164.9 G,与粉体相比,矫顽力有较大提升,有望扩展BaFe12O19在高密度垂直记录材料、微纳米电子材料和微波材料等领域的应用.     

硫化锌掺锰/聚乙烯醇复合纳米纤维的制备与表征

利用静电纺丝法与气固反应相结合, 成功地制备了硫化锌掺锰/聚乙烯醇复合纳米纤维, 并对所制备的复合物进行了表征, 探讨了复合物的结构及其性能.     

ZnS:Mn2+/聚苯乙烯核壳及ZnS:Mn2+中空球的制备和光谱性质

ZnS:Mn2+ polystyrene (PS) core-shell structures and ZnS:Mn2+ hollow spheres were prepared by a sonoehemical deposition approach. Transmission electron micrograph (TEM) studies show that the PS surface is covered by a thin shell consisted of ZnS: Mn2+ nanoparticles with an average size of 9 nm. ZnS: Mn2+ hollow spheres were obtained by heating the core-shell particles in air at 500 ℃ to drive off PS. The photoluminescence spectrum for the emission band of Mn2+ peaked at 540 nm, and a 45 nm blue shift compared to that of corresponding bulk sample, was discussed based on the Mn-O octahedral distortion induced by shell structure.     

静电纺丝法制备Y2O3纳米纤维与表征

采用静电纺丝法制备了PVA/Y(NO3)3复合纳米纤维,在适当的温度下进行热处理,得到Y2O3纳米纤维. 利用XRD,SEM,TG-DTA,FTIR等现代分析手段对样品进行了表征. XRD分析表明,PVA/Y(NO3)3复合纤维为无定型,焙烧温度在600 ℃以上得到晶态单相的Y2O3纳米纤维,属于立方晶系,空间群为Ia3. SEM分析表明,PVA/Y(NO3)3复合纤维表面光滑,平均直径为110 nm. 焙烧温度对Y2O3纳米纤维的形成有重要影响. 600 ℃焙烧得到的Y2O3纳米纤维的平均直径约50 nm,900 ℃焙烧得到的Y2O3纳米纤维由纳米颗粒堆积而成,部分已断裂. TG-DTA和FTIR分析表明,PVA,Y(NO3)3以及水分在600 ℃以上时完全分解挥发,最终样品为晶态单相的Y2O3纳米纤维.     

Mn:ZnSe/ZnS核-壳结构纳米晶的无膦法制备和光学性质

以溶于十八烯的Se作为Se前驱体,在无膦条件下制备得到了具有较高量子产率的Mn:ZnSe纳米晶.为了进一步提高纳米晶的稳定性和发光强度,运用外延生长的方法进行ZnS壳层包覆并得到了具有核-壳结构的Mn:ZnSe/ZnS纳米晶.X射线衍射、透射电子显微镜及吸收和荧光光谱测试结果表明,该方法合成的Mn:ZnSe纳米晶以及核-壳结构Mn:ZnSe/ZnS纳米晶均为闪锌矿结构,具有良好的单分散性,包覆ZnS外壳层后量子产率可达到60%以上.此外,对ZnS壳层厚度和Mn2+的掺杂量对Mn:ZnSe/ZnS纳米晶发光强度的影响及发光机制也进行了初步讨论.     

基于荧光素的荧光纳米纤维的制备与表征

以电纺聚丙烯腈(PAN)纳米纤维为起始物, 经乙二胺改性后, 再利用Mannich反应将荧光素共价连接于PAN纳米纤维薄膜表面. 用荧光光谱、 扫描电镜和红外光谱进行了结构表征. 结果表明, 利用荧光素对静电纺丝薄膜表面进行修饰, 获得了很强的荧光信号, 证明了方法的可行性.     

Synthesis and characterization of high-quality ZnS, ZnS:Mn2+, and ZnS:Mn2+/ZnS (core/shell) luminescent nanocrystals

High-quality ZnS, ZnS:Mn2+, and ZnS:Mn2+/ZnS (core/shell) nanocrystals (NCs) were synthesized via a high-boiling solvent process and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), electron paramagnetic resonance (EPR), X-ray photoelectron spectroscopy (XPS), and photoluminescence (PL) spectra. The monodisperse ZnS NCs (size = 8 nm), which self-assembled into several micrometer-sized domains, were achieved by adopting poly(ethylene glycol) (PEG) in the reaction process (without using a size-selection process). The obtained ZnS:Mn2+ and ZnS:Mn2+/ZnS core/shell NCs are highly crystalline and quasimonodisperse with an average particle size of 6.1 and 8.4 nm, respectively. All of the as-formed NCs can be well dispersed in hexane to form stable and clear colloidal solutions, which show strong visible emission (blue for ZnS and red-orange for ZnS:Mn2+ and ZnS:Mn2+/ZnS) under UV excitation. The growth of a ZnS shell on ZnS:Mn2+ NCs, that is, the formation of ZnS:Mn2+/ZnS core/shell NCs, resulted in a 30% enhancement in the PL intensity with respect to that of bare ZnS:Mn2+ NCs due to the elimination of the surface defects.     

Organometallic synthesis and electrophoretic characterization of high-quality ZnS:Mn/ZnS core/shell nanoparticles for bioanalytical applications

A novel and facile preparation method for colloidal ZnS nanoparticles doped with Mn²⁺ is introduced, using a simple one pot heating process followed by a capping procedure for saturation of the surface bound doping atoms to increase the nanoparticles’ stability and photoluminescence quantum yield. The particles were transferred into water with a standard ligand exchange method and investigated by means of laser Doppler electrophoresis, agarose gel electrophoresis, and isotachophoresis. Correspondence: Alexey Merkulov, Freiburg Materials Research Centre (FMF), University of Freiburg, Stefan-Meier-Strasse 21, D-79104 Freiburg, Germany     

ZnO纳米纤维的静电纺丝及其光催化性能的研究

以聚乙烯醇溶液为络合剂与醋酸锌反应制得前驱体溶液,采用静电纺丝法制备PVA/Zn(Ac)2复合纳米纤维,经过高温煅烧得到直径为100 nm的ZnO纳米纤维,采用差热-热重分析、红外光谱分析、X射线粉末衍射分析及扫描电镜等手段对其进行了表征.光催化降解酸性品红溶液的实验结果表明,太阳光照65 min使质量浓度为45 mg/L酸性品红水溶液的脱色率达93%;另外,重复使用ZnO纳米纤维4次之后,其光催化降解率仍能达到70%以上.这充分说明ZnO纳米纤维具有良好的光催化性能.     

Thermal shrinkage of electrospun PVP nanofibers

This paper outlines the shrinkage of electrospun polyvinylpyrrolidone (PVP) fiber mats during thermal treatment. The thermal behavior and phase changes within the fibers were investigated by DSC and TGA/DTA. Five precursors with different PVP loading in ethanol were electrospun. The mats shrinkage as function of temperature was measured in the RT–200 °C range. Shrinkage rate drastically increased above the polymer glass transition point, T_g (150–180 °C), due to increase in polymer chain mobility. Mats shrinkage at 200 °C as function of PVP concentration showed a minimum at ∼10%wt. Below 10% PVP the mats morphology is non‐uniform, consisting of beads and fibers. Above 10% PVP, only flat and uniform fibers were observed. This paper outlines the dominant mechanism governing the mats shrinkage during heating. In addition, the effect of PVP concentration on the expansion of fibers diameter was investigated and found to be consistent with the linear shrinkage observing a minimum at ∼10% PVP. The effect of applied voltage on mat shrinkage was investigated, and showed a minimum at 12 kV. Understanding the interplay between fibers morphology and thermal shrinkage allows precursor composition and system optimization needed for minimizing shrinkage negative effects on the structure and properties of electrospun fiber mats. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 248–254     

Fabrication and properties of Mn0.5Zn0.5Fe2O4 nanofibers

Zn-doped α-FeOOH nanofiber was synthesized by coprecipitation method. Then the α-FeOOH was enwraped by the complex of the Mn²⁺ and citric acid. The morphology of α-FeOOH did not transform after the calcination process and Mn_0.5Zn_0.5Fe₂O₄ nanofiber was successfully prepared. The phase, morphology, particle diameter and the magnetic properties of samples were studied by X-ray diffraction (XRD), transmission electron microscopy (TEM) and vibrating sample magnetometer (VSM). The results indicated that Mn_0.5Zn_0.5Fe₂O₄ nanofibers with an aspect ratio over 40 and a diameter of 20 nm were prepared. Compared with the amorphous Mn_0.5Zn_0.5Fe₂O₄, the anisotropy of the Mn_0.5Zn_0.5Fe₂O₄ nanofiber increased, resulting in the higher coercivity and magnetization of the obtained sample. With an increase in the calcination temperature, the diameter and the saturation magnetization of the sample increased, while the aspect ratio and coercivity decreased. The coercivity of the sample obtained at 700 °C was maximal (up to 185.4 Oe). The saturation magnetization of the sample obtained at 900 °C was maximal (up to 65.3 emu/g). The use of citric acid method prevented the presence of Mn(OH)₂, resulting in the decrease of the calcination temperature.     

Alumina nanofibers obtained via electrospinning of pseudo-boehmite sol/PVP solution

Alumina nanofibers were fabricated by calcination of the polyvinylpyrrolidone (PVP)/pseudo-boehmite nanocomposite precursor fibers formed by electrospinning PVP/ethanol solution of dispersed pseudo-boehmite nanoparticles with and without additive of silica. The evolution of the phase, mechanical property and morphological features of the calcined fibers were studied and the effect of adding SiO₂ on the phase transformation of alumina was discussed. Adding SiO₂ can retard the phase transformation of γ-Al₂O₃ to α-Al₂O₃ and therefore inhibit the growth of alumina grains during calcination. Upon calcining the precursor fibers with 4 wt% SiO₂ additive at 1,300 °C, continuous alumina nanofibers with diameter ranging from 300 to 800 nm were obtained. These continuous nanofibers exhibited good flexibility and could be very promising for applications in filtration and catalyst support.     

反胶束法制备SiO2包裹的ZnS:Mn/ZnS量子点

采用反胶束法制备了SiO2包裹的ZnS∶Mn/ZnS量子点(1)。1的UV吸收峰在295 nm附近,低于体相ZnS(约340 nm);1中Mn2+含量升高,ZnS基质的缺陷荧光发射峰减弱,595 nm处的Mn2+特征荧光发射峰增强;但Mn2+含量过高时产生荧光淬灭。光学显微镜和透射电镜分析表明,1分散性较好,内核呈结晶态;Mn2+含量为2.2%时,1的内核直径和SiO2壳层厚度分别为6 nm和5 nm左右。     

Water-soluble silica-overcoated CdS:Mn/ZnS semiconductor quantum dots

Highly luminescent and photostable CdS:Mn/ZnS core/shell quantum dots are not water soluble because of their hydrophobicity. To create water-soluble quantum dots by an appropriate surface functionalization, CdS:Mn/ZnS quantum dots synthesized in a water-in-oil (W/O) microemulsion system (reverse micelles) were consecutively overcoated with a very thin silica layer ( approximately 2.5 nm thick) within the same reverse micellar system. The water droplet serves as a nanosized reactor for the controlled hydrolysis and condensation of a silica precursor, tetraethyl orthosilicate (TEOS), using an ammonium hydroxide (NH4OH) catalyst. Structural characterizations with transmission electron microscopy (TEM) and x-ray photoelectron spectroscopy (XPS) indicate that the silica-quantum dot nanocomposites consist of a layered structure. Owing to the amorphous, porous nature of a silica layer, the optical and photophysical properties of silica-overcoated CdS:Mn/ZnS quantum dots are found to remain close to those of uncoated counterparts.     

Poly(MAA-Mn) for Triple-Layer Structure Synthesis of ZnS/ZnS:Mn/SiO2 Phosphors

Methacrylic acid (MAA) was used as a manganese carrier to prepare ZnS/MAA-Mn particles, and ZnS/ZnS:Mn phosphors were formed from ZnS/MAA-Mn by ion substitution through heat treatment. After silica coating on surface by chemical precipitation method with tetraethyl orthosilicate (TEOS), ZnS/ZnS:Mn/SiO₂ phosphors were prepared successfully as a new core/shell structure compound. The thickness of layers was controlled by adjusting concentrations of manganese (II) acetate (Mn(CH₃COO)₂) and TEOS. Structure, morphology, and composition of prepared phosphors were investigated by X-ray diffraction (XRD), transmission electron microscope (TEM), and X-ray photoelectron spectroscopy (XPS), respectively. Photoluminescence (PL) properties of ZnS with different Mn²⁺ content were analyzed by PL spectrometer. PL emission intensity and PL stability were analyzed for evaluating effects of silica coating and Mn²⁺ activator doping. As a result, the structure of two layers could be observed, and optimum composition of ZnS/ZnS:Mn/SiO₂ structure was also obtained.