Sensitivity of cationic surfactant templates to specific anions in liquid interface crystallization

We investigated the specific effects of potassium salts of various anions upon the interfacially templated crystal nucleation of K(2)SO(4). Previously, we have shown that the presence of several salts at low concentrations could induce changes in important crystallization characteristics templated by 1-octadecylamine at the liquid-liquid interface, and that these changes depended greatly on the specific identity of the salt. In this work we extend our surfactant monolayers to include dimethyldioctadecylammonium bromide (DODAB) and hexadecyltrimethylammonium bromide (CTAB). Addition of 10 mM of various potassium salts results in a diminution in efficiency of the templating capability of CTAB monolayer, as evidenced by higher C(onset) values and polycrystalline habit. The ability of the anions to perturb these values varied in a manner consistent with a Hofmeister series. However, DODAB maintained its templating effectiveness regardless of the nature of the salt or concentration. DODAB and CTAB are likely to be undergoing different reordering effects in the monolayer upon binding with chaotropic anions: a combined reduction in surface charge with different monolayer ordering results in a differing template ability. These studies have provided significant insights into the understanding of the interaction of ordered surfactant arrays with salts, and provide exciting possibilities for crystal engineering and materials design.     

On the mechanism of adsorption of a cationic surfactant on quartz

Experimental data on surface charge of quartz in dependence on concentration of CTAB solution and pH were obtained using capillary electrokinetic method. The results are compared with the developed theory of the Langmuir-type adsorption that takes Into account adsorption both on charged and noncharged surface centers. Computer optimization procedure results in adsorption potential values −15 kT and −11 kT, respectively. A ratio between surface concentrations of the centers was also estimated.     

Dewetting behavior of aqueous cationic surfactant solutions on liquid films

Previous experimental work has shown that the spreading of a drop of aqueous anionic surfactant solution on a liquid film supported by a negatively charged solid substrate may give rise to a fingering instability (Afsar-Siddiqui, A. B.; Luckham P, F.; Matar, O. K. Langmuir 2003, 19, 703-708). However, upon deposition of a cationic surfactant on a similarly charged support, the surfactant will adsorb onto the solid-liquid interface rendering it hydrophobic. Water is then expelled from the hydrophobic regions, causing film rupture and dewetting. In this paper, experimental results are presented showing how the surfactant concentration and film thickness affect the dewetting behavior of aqueous dodecyltrimethylammonium bromide solutions. At low surfactant concentrations and large film thicknesses, the film ruptures at a point from which dewetting proceeds. At higher concentrations and smaller film thicknesses, the ruptured region is annular in shape and fluid moves away from this region. At still higher concentrations and smaller film thicknesses, the deposited surfactant forms a cap at the point of deposition that neither spreads nor retracts. This variation in dewetting mode is explained by considering the relative Marangoni and bulk diffusion time scales as well as the mode of assembly of the surfactant adsorbed on the solid surface.     

Use of marker ion and cationic surfactant plastic membrane electrode for potentiometric titration of cationic polyelectrolytes

A plasticized poly (vinyl chloride) (PVC) membrane electrode sensitive to stearyltrimethylammonium (STA) ion is applied to the determination of cationic polyelectrolytes such as poly (diallyldimethylammonium chloride) (Cat-floc) by potentiometric titration, using a potassium poly (vinyl sulfate) (PVSK) solution as a titrant. The end-point of the titration is detected as the potential change of the plasticized PVC membrane electrode caused by decrease in the concentration of STA ion added to the sample solution as a marker ion due to the ion association reaction between the STA ion and PVSK. The effects of the concentration of STA ion, coexisting electrolytes in the sample solution and pH of the sample on the degree of the potential change at the end-point were examined. A linear relationship between the concentration of cationic polyelectrolyte and the end-point volume of the titrant exists in the concentration range from 2×10⁻⁵ to 4×10⁻⁴ N for Cat-floc, glycol chitosan, and methylglycol chitosan.     

Two-step stacking by sweeping and micelle to solvent stacking using a long-chain cationic ionic liquid surfactant

Coupling of long‐chain ionic liquid (LCIL)‐based sweeping and micelle to solvent stacking (MSS) in CZE for anionic compounds was proposed. N‐Cetyl‐N‐methylpyrrolidinium bromide (C₁₆MPYBr) was used as a novel cationic surfactant. The capillary column was conditioned with poly(1‐vinyl‐3‐butylimidazolium) bromide, a kind of polymeric ionic liquid, to obtain the anodic electroosmotic flow (EOF). There is a micellar solution (MS) zone which is prepared with C₁₆MPYBr before the sample zone. The micelles penetrated into the sample zone, swept and transported the analytes toward the micelle to solvent boundary (MSSB). Meanwhile, a sufficient amount of methanol in the background solution (BGS) resulted in the reversal of effective electrophoretic mobility of analytes and completed the MSS. Under optimal conditions, good linearity (0.9988–0.9999) was obtained for model analytes in a wide linear range with limits of detection (LODs) from 0.025 to 0.25 mg/L. The intraday and interday repeatabilities (%RSD, n=5, 10) were acceptable in the range from 2.12 to 7.29%. 34 and 25 times increases in peak area sensitivity for benzoic acid (BA) and 2‐nitrophenol (2‐NP) and 60 times increase in peak height sensitivity for 4‐chlorophenol (4‐CP) were obtained. The proposed method is applied to analyze two spiked environmental water samples obtaining satisfactory recoveries.     

Spontaneous aggregate transition in mixtures of a cationic gemini surfactant with a double-chain cationic surfactant

Controllable aggregate transitions were realized by mixing two kinds of cationic surfactants, hexylene-1,6-bis(dodecyldimethylammonium bromide) (C(12)C(6)C(12)Br(2)) and didodecyldimethylammonium bromide (DDAB). It was found that two parameters are the main factors determining the aggregation behavior of the mixed system, the total concentration of DDAB and C(12)C(6)C(12)Br(2) (C(T)), and the mole fraction of DDAB in the mixtures of DDAB and C(12)C(6)C(12)Br(2) (X(DDAB)). How these two parameters act on the aggregate transitions was studied in detail by various measurements including surface tension, turbidity, electrical conductivity, ζ potential, isothermal titration microcalorimetry, dynamic light scattering, cryogenic transmission electron microscopy, and (1)H NMR. When C(T) was constant, spontaneous vesicle-to-micelle transitions were found with decreasing X(DDAB) at high C(T). When X(DDAB) was constant, aggregate transitions were generated by gradually increasing C(T), depending on different X(DDAB) ranges. At X(DDAB) < 0.6, small spherical aggregates formed first and then transferred to vesicles, and finally the vesicles transitioned to micelles. At X(DDAB) ≥ 0.6, the progressive increase in C(T) led to aggregate transitions on the order of the arising of vesicles, the continuous growth of vesicles, the disruption of vesicles into micelles, and the final coexistence of vesicles and micelles. The hydrophobic interaction and electrostatic repulsion between DDAB and C(12)C(6)C(12)Br(2) together with the related degree of ionization and hydration of the surfactants were gradually adjusted by changing the ratio and the total concentration of these two surfactants, which should be responsible for the complicated aggregation behavior.     

Spectroscopic studies of stratum corneum model membrane from Bothrops jararaca treated with cationic surfactant

This research employed FT-Raman and PAS-FTIR spectroscopic techniques to evaluate the interaction of cetyl trimethyl ammonium chloride (CTAC), a cationic surfactant, on the stratum corneum (SC) of shed snake skins from Bothrops jararaca, used as model membranes. Surfactant aqueous solutions (50.0 and 0.78 gl(-1)) with neutral pH were applied on the samples with intervals of 4, 8 (whole SC) and 12h (SC tape-stripped). Samples presented modifications of the topography for all conditions of the assays and the monomers of the surfactant, instead of the micelles, seemed to interact with the keratin. The SC model membranes treated with CTAC have had an augment of water content (except for whole SC treated for 8h) indicated by the expansion of the band 3600-3300 cm(-1), mainly for the tape-stripped samples after 12h treatment. Concentration appeared to be an important factor related to an increase of the tissue hydration.     

Kinetics and mechanism of phosphorylation of monoethanolamine in reversed micelles of a cationic surfactant

The reactions of monoethanolamine with 4-nitrophenyl esters of tetracoordinated phosphorus acids in chloroform in the presence of 2-hydroxyethyldimethylpentadecylammonium bromide were studied. The effective rate constants of the reactions are increased by more than two orders of magnitude in the presence of the micelle-forming cationic surfactant. The latter also favors the formation of the product ofO-phosphorylation of monoethanolamine and leads to the appearance of a new ionic form of the 4-nitrophenol-monoethanolamine complex. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2, pp. 280–283, February, 1998.     

Facilitated transport through liquid surfactant membrane: Analysis of breakage model

A mathematical model for analyzing the experimental data of extraction of weak acid from aqueous solution by liquid surfactant membrane (LSM) using a strong base as internal reagent present in excess in a batch system has been presented. The leakage of internal phase due to membrane breakage is also discussed in the mathematical treatment. The model while considering a reaction front to exist within the emulsion globule assumes reaction equilibrium between the solute and internal reagent in the external continuous phase. The proposed model predicts successfully the experimental results of extraction of a weak acid by a strong base in a batch separation system as presented in the literature. The model is also capable of predicting excellently the experimental pH versus time data in case of the above system.     

Contribution of micelles to ionic strength of surfactant solution

A new definition of the concentration-dependent "shielding factor" has been proposed, along with its particular value at a concentration assumed to be equal to critical micelle concentration (cmc). It has been shown that herein defined shielding factor enables one to calculate the values of monomer (a(x)) and counterion activities (a(y)) which are in better agreement with the measured ones than those calculated using Burchfield and Wooley's constant value of the shielding factor. In addition, it was shown that by using particular value of shielding factor at cmc, one is able to calculate the micellar charge radius which is dependent on aggregation number, counterion parameter and cmc, all of them having important implications for thermodynamic treatment of the micellization process.     

Ionic rectification properties of a bipolar interface consisting of a cationic surfactant and cation-exchange membrane

A novel bipolar interface that consists of cationic surfactant and cation-exchange membrane was successfully prepared in an aqueous electrolyte system. This bipolar interface shows a ionic rectification behavior similar to that observed in bipolar membranes. However, different from bipolar membranes, this system has a total rectification behavior, where we cannot observe the occurrence of a water-splitting phenomenon, which always occurs in the bipolar membrane process under reverse bias conditions.     

Cathode catalysts degradation mechanism from liquid electrolyte to membrane electrode assembly

Single-cell and half-cell degradation test procedures were evaluated for carbon-supported Pt/C, PtCo/C and PtNi/C catalysts. Half-cell analyses were employed to understand the effect of the number of cycles and of the scan rate over the cathode catalysts degradation under potential cycling from 0.6 to 1.2 V. The data suggested a time-dependent degradation for all three catalytic systems. Single-cell measurements were used to evaluate the impact of catalyst degradation on fuel cell performance. The measurements in both setups showed similar ECSA and ORR mass activity losses. Specific degradation mechanisms related to Pt dissolution, Pt agglomeration, and transitional metal leaching were quantified and correlated with performance losses.     

Extraction and separation of cationic surfactants from river sediments: application to a spectrophotometric determination of cationic surfactant in an aquatic environment using membrane filters.

The quantitative extraction of cationic surfactant (CS+) in river sediments was studied. Further, the developed method was applied to the spectrophotometric determination of CS+ in urban river sediment samples by solid-phase extraction with membranes. A mixture of methanol and hydrochloric acid was proposed as an eluent. Dried sediment was digested in the eluent under ultrasonic irradiation. After elution, the eluent was evaporated to almost dryness. The residue was dissolved in a small volume of methanol and diluted to a certain volume with water. The pH of the solution was adjusted to 4-5 to separate iron and some other metals as precipitates of hydroxides. The solution was passed through two-piled membranes: first glass-fiber and then polytetrafluoroethylene (PTFE) membranes. A small volume of methanol was passed through the membranes to elute any CS+ retaining on the membranes. After passing the methanol solution through a cationic exchange resin column, the retained CS+ was eluted with methanol containing a high concentration of sodium chloride. Water, Bromophenol Blue (BPB) and hydrochloric acid were added to the solution. The solution was passed through a mixed cellulose ester membrane filter to retain an ion associate of CS+.BPB-. The retained ion associate was dissolved in a small volume of N,N-dimethylformamide together with the membrane filter, followed by the addition of triethanolamine to make the solution alkaline. The absorbance due to BPB2- was measured at 603 nm against a reagent blank. This method was applied to the determination of CS+ in river water and sediment. A cationic surfactant in sediments at 10(-5) mol kg-1 levels was detected with satisfactory precision. It was found that CS+ was about 500-fold enriched in the sediment from water at the place where domestic wastewater was discharged.     

New bulk liquid membrane oscillator composed of two coupled oscillators with diffusion-mediated physical coupling

A new type of bulk liquid membrane system, which represents the first example of a bulk liquid membrane oscillator characterised by the presence of two coupled oscillators, is described. When the benzyldimethyltetradecylammonium chloride surfactant undergoes an oscillatory mass transfer through a nitromethane liquid membrane, a new liquid layer (phase X) appears between the membrane and the acceptor phase. Kinetic analysis provides evidence that the whole system is composed of two coupled oscillators with diffusion-mediated physical coupling. The first component oscillator (based on nitromethane) of lower frequency delivers the driving material to the second one (phase X-based oscillator) leading to additional higher frequency oscillations. A new molecular mechanism is proposed for interpreting the experimental observations. The results might enhance understanding of intercellular communication in biology, where periodic signalling is more efficient than any other type of signalling mode.     

The behaviour of drag-reducing cationic surfactant solutions

The behaviour of two types of drag reducing surfactant solutions was studied in turbulent flows in pipes of different diameters. Our surfactant systems contained rod-like micelles; they consisted of equimolar mixtures ofn-tetradecyltrimethylammonium bromide,n-hexadecyltrimethylammonium bromide, and sodium salicylate. The structure of the turbulence was studied using a laser-Doppler anemometer in a 50 mm pipe. In the turbulent flow regime both surfactant solutions exhibited characteristic flow regimes. These flow regimes can be influenced by changing the amount of excess salt, the surfactant concentration, or the temperature. Shear viscosity measurements in laminar pipe and Couette flows show the occurrence of the so-called shear-induced state, where the viscosity increases and the surfactant solution becomes viscoelastic. The shape of the turbulent velocity profile depends on the flow regime. In the turbulent flow regime at low Reynolds numbers, velocity profiles similar to those observed for dilute polymer solutions are found, whereas at maximum drag reduction conditions more S-shaped profiles that show deviations from a logarithmic profile occur. An attempt is made to explain the drag reduction by rod-like micelles by combining the results of the rheological and the turbulence structure measurements.     

IGC studies of binary cationic surfactant mixtures

Inverse gas chromatography (IGC) has been used to measure the interaction parameter between two twin-tailed cationic surfactants. Didodecyldimethylammonium (DDAB) and dioctadecyldimethylammonium (DODAB) bromides and their mixtures were used as stationary phases. IGC and DSC techniques have been used for the determination of the temperature zone of working. The activity coefficients at infinite dilution (on a mole fraction basis) were calculated for eleven probe solutes on each pure surfactant column. Values of interaction parameter between surfactants obtained at four weight fractions of the mixtures and at five temperatures are positive and suggested that the interactions is more unfavourable with the increment of DODAB concentration in the mixture. The results are interpreted on the basis of partial miscibility between DDAB and DODAB.     

Concentration of amino acids by a liquid emulsion membrane with a cationic extractant

The concentration of -phenylalanine in a liquid emulsion membrane system was studied using a cation complexing agent, di-2-ethylhexyl phosphoric acid (D2EHPA), as a carrier. The membrane formulation, the pH in the internal phase of the acid concentration in the external phase were optimized with respect to concentration performance and membrane stability. It was found that a liquid emulsion membrane obtained by demulsification of the emulsion by an electrostatic coalescer could be reused. Based on the laboratory tests, a continuous multistage process for the concentration of amino acids was proposed (with the development of a commercial process in mind) and its technical feasibility was discussed.     

Capillary liquid chromatography using a hydrophilic/cation-exchange monolithic column with a dynamically modified cationic surfactant

A novel form of reversed-phase liquid chromatography (RPLC) by the dynamically modified hydrophilic interaction monolithic column has been described in this paper. A porous poly(SPMA-co-PETA) monolith with strong cation-exchange (SCX) was prepared and the resulting monolith showed a typical hydrophilic interaction chromatography (HILIC) mechanism at higher organic solvent content (ACN% > 50%). The good selectivity for neutral, basic and acidic polar analytes was observed in the HILIC mode. In order to increase the hydrophobic interaction, the monolith with SCX was dynamically modified with a long-chain quaternary ammonium salt, cetyltrimethylammonium bromide (CTAB), which was added to the mobile phase. CTAB ions were adsorbed onto the surface of the SCX monolithic material, and the resulting hydrophobic layer was used as the stationary phase. Using the dynamically modified SCX monolithic column, neutral, basic and acidic hydrophobic analytes were well separated with the RPLC mode.     

Effect of cationic surfactant on the formation of ferron complexes

In the spectrophotometric determination of aluminium and iron with ferron (7-iodo-8-quinolinol-5-sulphonic acid, H(2)L), the addition of cationic surfactants greatly improves the linearity of the calibration curve and widens the useful pH range. The effect of cetyltrimethylammonium chloride (CTMAC) on the stepwise stability constants (K(1),K(2) and K(3)) of the ferron complexes of aluminium and iron (ML(+), ML(-)(2) and ML(3-)(3)) and on the acid-dissociation constants (K(a1) and K(a2)) of ferron has been studied in connection with the role of the surfactant. CTMAC greatly increases the value of K(3) while exerting little effect on K(1) and K(2), thus rendering ML(3-)(3) the predominant species even at very low concentration of free L(2-). It also has some effect on the acid-dissociation constants of ferron, but sometimes it acts to decrease the free L(2-) concentration. At is therefore concluded that the improvements due to addition of surfactant should be attributed to the increased K(3) value. The presence of surfactant micelles is not essential, because the surfactant has a favourable effect when present at well below its critical micelle concentration, and because the continuous variations plots show a peak at a point corresponding to the composition M: L: Q (Q = cationic surfactant) = 1:3:3.