多孔Pd/α-Al2O3 活性膜上 1,5-环辛二烯选择加氢

利用微乳液及浸渍技术制备了多孔Pd/α-Al2O3催化活性膜.利用透射电镜、扫描电镜和X射线衍射对微乳液中及α-Al2O3陶瓷膜孔结构中纳米Pd颗粒的形貌和分布进行了表征.分析结果表明,通过浸渍技术,微乳液中的纳米Pd颗粒以几百纳米大小的晶体形态均匀负载于陶瓷膜孔中.在"催化接触器"型膜反应器中,以1,5-环辛二烯催化加氢为模型反应,考察了多孔Pd/α-Al2O3膜的活性与选择性,并与Pd-聚丙烯酸(PAA)有机催化膜反应器、悬浮床反应器和固定床反应器中的催化性能进行了比较.结果表明,Pd/α-Al2O3膜反应器的催化活性与目的产物1-环辛烯的选择性远高于Pd-PAA有机膜反应器和固定床反应器.Pd/α-Al2O3膜反应器在强化传质和消除孔内扩散方面效果显著,这与Pd在陶瓷膜孔中的分布及反应物在膜反应器中的高速流动有关.     

二甲醚部分氧化重整制氢中的部分氧化催化剂的考察

采用浸渍法制备了一系列负载型贵金属催化剂,与Ni/Al2O3构成双床层催化剂,在连续流动固定床反应器中,进行了二甲醚(DME)部分氧化重整制氢的研究,系统地考察了贵金属类型及其负载量、载体以及还原温度与反应温度的影响.结果表明,Pd/Al2O3催化性能不及Pt/Al2O3和Rh/Al2O3,而Pt/Al2O3和Rh/Al2O3催化性能相当,考虑到价格因素,选择了Pt/Al2O3作为本反应催化剂.对Pt负载量的考察表明,0.5%Pt/Al2O3催化性能最佳,且Al2O3又比MgO和ZrO2更适合作载体.通过对工艺条件的考察,确定适当的还原温度与反应温度均为700℃.在上述最佳催化剂与反应条件下,DME转化率保持在100%,H2收率可达80%.     

介孔Al2O3负载PdO催化甲烷燃烧反应性能

采用浸渍法制备了介孔Al2O3(M-Al2O3)负载PdO催化剂,考察了其催化CH4燃烧反应性能.结果表明,以M-Al2O3为载体的PdO催化剂活性比普通Al2O3载体高得多,这很可能与M-Al2O3的孔道结构对PdO物种的限域作用有关.随着PdO/M-Al2O3催化剂焙烧温度的升高,甲烷催化燃烧活性先增加后降低,其中700oC焙烧的催化剂活性最高,400oC反应时CH4转化率为91%.此时Pd物种主要以PdO颗粒形式高度分散在载体的介孔孔道内,而高温焙烧时,Pd物种主要以Pd和PdO的混合晶相存在.尽管900oC焙烧制得的催化剂上CH4的转化率降低,但TOF值最大,这可能与该催化剂中同时存在金属Pd和PdO有关.     

焙烧温度对 Pd/Al2O3 催化剂上甲烷燃烧反应性能的影响

 考察了载体与催化剂焙烧温度对 Pd/Al2O3 催化剂上低浓度甲烷催化燃烧反应性能的影响. 采用 X 射线衍射、透射电镜、N2 物理吸附、NH3 程序升温脱附和 O2 程序升温氧化等手段对载体和催化剂进行了表征. 结果表明, 焙烧温度对催化剂活性及稳定性的影响显著. 随着载体焙烧温度的升高, Al2O3 的比表面积、物相结构、酸中心的数量及强度明显改变, 相应的 Pd/Al2O3 催化剂中载体与 Pd 的相互作用减弱, Pd 分散度降低. 当载体焙烧温度为 1 100 °C, Pd/Al2O3 焙烧温度为 200 °C 时, 所得催化剂在 260 h 的连续反应中, 甲烷转化率始终维持在 99%以上.     

Mn修饰Al2O3载体负载Pd催化剂及其蒽醌加氢催化性能

以活性氧化铝(γ-Al2O3)为载体,分别以Mn(NO3)2溶液和酸性氯化钯(PdCl2)溶液为修饰组分和活性组分前体,采用分步浸渍法制备了Mn修饰Al2O3载体负载钯催化剂。将催化剂应用于蒽醌加氢反应,考察了催化剂制备方法、活性组分负载量和催化剂还原温度对反应效果的影响。用XRD、BET、XPS和TPR对催化剂进行了表征。结果表明,催化剂活性受到制备方法的影响,在对Mn修饰Al2O3载体进行焙烧,Pd负载量0.2(wt)%、还原温度300℃的条件下,催化剂蒽醌加氢活性较高,较未修饰的催化剂提高了约16%。催化剂中Mn以MnO的形式存在,影响了γ-Al2O3的组织结构,使载体与活性组分之间的作用力增强,活性组分Pd高度分散在催化剂表面,从而提高了催化剂的活性。     

一种TiO2修饰的Pd/Al2O3选择性加氢用催化剂的研究

 研制了一种用TiO2修饰的Pd/Al2O3(Pd/Al2O3-TiO2)选择性加氢催化剂,并采用N2吸附,XRD,SEM,FT-IR,TPD和TPR等手段对催化剂进行了表征,考察了催化剂的催化性能. 结果表明,Pd/Al2O3-TiO2催化剂具有较小的比表面积; 低的表面酸性,且以弱酸中心为主; TiO2在Al2O3表面呈高度分散,并集中于载体到一定的深度; 用含钛溶液浸渍次数以1次为佳. 载体中TiO2的添加使得PdO更易于被还原. 用这种复合氧化物作载体制备的催化剂表现出更高的加氢活性和选择性,优于单纯以Al2O3作载体的催化剂.     

超声浸渍法制备Pd/Al2O3催化剂及其催化蒽醌加氢性能

 以球形 γ-Al2O3 和 θ-Al2O3 为载体,分别采用超声浸渍和普通浸渍方法制备了Pd含量为0.3%的负载型催化剂,并将其用于蒽醌加氢反应. 采用X射线衍射、 N2吸附和透射电镜等手段对催化剂的理化性质和孔结构进行了分析,考察了浸渍方法对催化剂活性金属分散度的影响. 结果表明,与普通浸渍法相比,超声浸渍法制备的负载型Pd催化剂金属分散度明显提高,因而对蒽醌加氢反应表现出较高的催化活性. 以960 ℃焙烧的球θ-Al2O3 为载体,通过超声浸渍制备的负载型Pd催化剂具有较高的Pd分散度和较大的孔径,在蒽醌加氢反应中对反应物的扩散阻力较小,因而表现出更高的催化活性,而且反应中催化剂的稳定性良好.     

单层分散型Pd/Ni双金属催化剂的制备及其催化加氢性能

通过置换反应制备了Pd/Ni双金属催化剂,利用X射线衍射、CO化学吸附和吸附H2的程序升温脱附对其进行了表征,并测定了该催化剂对环己烯、苯乙烯和丙酮气相加氢反应的催化性能.结果发现,在这种催化剂中Pd原子单层分散在金属Ni的表面,因而该催化剂表现出比浸渍法制备的相同Pd含量的Pd/Ni-im和Pd/-γAl2O3催化剂更高的催化加氢活性.     

制备条件对Pd催化剂上C3H6选择性还原NO性能的影响

采用浸渍法和溶胶凝胶法,制备了Pd/AI2O3和Pd/AI2O3-CeO2样品,并测定了不同温度焙烧后催化剂的物相、比表面积及对丙烯选择性还原NO的活性。对于Pd/AI2O3,随着焙烧温度的提高,其NO的最大转化率逐渐下降,对应的反应温度在290－310℃左右,而溶胶凝胶法制备的样品活性略高于浸渍法制备的样品;对于Pd/AI2O3-CeO2,经600℃焙烧后,其NO的最大转化率为22％,900℃焙烧的催化剂样品上NO的最大转化率达到40％左右,对应的反应温度也逐渐下降,说明活性随焙烧温度的提高而明显提高,溶胶凝胶法和浸渍法制备的样品结果很接近,浸渍法制备了若干不同Pd负载量的Pd/AI2O3样品,活性测定的结果表明,Pd含量在0．5％左右的催化剂样品中具有最高的活性。     

KBH4还原法制备超细Pd/γ-Al2O3 催化剂及其在蒽醌加氢反应中的应用

 通过KBH4还原浸渍到载体上的Pd物种制备了超细Pd/γ-Al2O3 催化剂,并采用X射线衍射、高倍透射电镜、能谱、能量损失谱和电感耦合等离子体发射光谱等对其进行了表征. 结果表明,催化剂中活性组分Pd以纳米尺度的微晶形式存在,而不是Pd-B非晶态合金. 蒽醌加氢制双氧水反应证明,与浸渍焙烧法制备的PdO/γ-Al2O3 催化剂相比,经KBH4还原制得的Pd/γ-Al2O3 催化剂中钯的晶体颗粒更小,分散度更高,从而催化剂的活性更高,其氢化效率比PdO/γ-Al2O3 提高了35%.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

解决能源问题的新途径--光解水制氢的研究

面对日益枯竭的能源危机,氢能是一种洁净、最有前景的替代能源。目前在各种制氢的方法中光催化分解水制氢的研究最多,光解水过程中催化剂最关键,本文对利用太阳能光解水的途径、提高光催化反应效率以及光催化剂的开发研究进行了综述。