Experimental study of the temperature field generated during orthogonal machining of an aluminum alloy

During the machining of metals, plastic deformation and friction lead to the generation of heat in the workpiece, which results in thermomechanically coupled deformation. Recently, several numerical models of this highly coupled process have been produced in response to increased interest in high speed machining. It is important to characterize the thermal field in the cutting zone in order to completely verify these models of high speed machining and to direct further advancement in this area. In this work, HgCdTe infrared detectors are used to experimentally measure the temperature distribution at the surface of a workpiece during orthogonal cutting. From these temperature measurements, the heat generated in the primary shear zone and the friction zone can be examined and characterized. A modified Hopkinson bar technique has been developed to perform orthogonal machining at speeds ranging from 10 to 100 m/s. In the present work, a cutting velocity of 15 m/s is employed in all the tests in order to demonstrate the capability of the apparatus and characterize thermal fields during low speed machining. Temperature fields are obtained during the orthogonal cutting of aluminum as a function of depth of cut. It is seen that depth of cut can vary both the maximum temperature as well as the distribution of the temperature field in the aluminum workpiece. the maximum temperature increased with depth of cut (238°C for 1.5 mm cut, 207°C for 1.0 mm cut and 138°C for 0.5 mm cut) and the temperature field extended further beneath the cut surface with decreasing depth of cut.     

Temperature and deformation measurements in transient metal cutting

Metal cutting is a thermomechanically coupled process in which plasticity induced heating and friction play a critical role. The objective of this work is to develop a methodology to understand and quantify this coupling. Temperatures of the workpiece and the chip during transient cutting processes are measured using a linear array of 16 InSb infrared detectors with 200 ns rise time and 27 μm spatial resolution. Three different materials, 1018 CR steel, Al6061-T6 and Ti-6Al-4V, are tested at a cutting speed of 4.3 m s⁻¹. A grid method is used to measure deformations during the above set of experiments. Measured values of temperature and deformation are compared to results of finite element simulations of the experiments.     

Investigation of stresses in he orthogonal cutting of fiber-reinforced plastics

A photoelastic study was conducted to examine the stress fields in the cutting process of fiber-reinforced plastics (FRPs). Force measurements were made and used in the analysis of the stress fields. Machined surfaces of workpieces with fibers oriented away from the cutting direction showed that the fibers were machined by shearing and tensile fracture; and when fibers were inclined towards the cutting tool, the fibers failed by shearing and bending. In addition, fiber-matrix debonding was observed to be maximum for fibers oriented at 45 deg towards the tool's path. Fiber orientation was shown to have an influence on the machining forces and stresses.Paper was presented at the 1994 SEM Spring Conference held in Baltimore, MD on June 6–9.     

A Methodology for Temperature Correction When Using Two-Color Pyrometers - Compensation for Surface Topography and Material

In this investigation, the applicability of the two-color pyrometer technique for temperature measurements in dry hard turning of AISI 52100 steel was studied, where both machined surfaces as well as cutting tools were considered. The impacts of differing hard turned surface topography on the two-color pyrometer readings was studied by conducting temperature measurements on reference samples created using cutting tools with different degrees of tool flank wear. In order to conduct measurements in a controlled environment, a specially designed furnace was developed in which the samples were heated step-wise up to 1,000 °C in a protective atmosphere. At each testing temperature, the temperatures measured by the two-color pyrometer were compared with temperatures recorded by thermocouples. For all materials and surfaces as studied here, the two-color pyrometer generally recorded significantly lower temperatures than the thermocouples; for the hard turned surfaces, depending on the surface topography, the temperatures were as much as ~20 % lower and for the CBN cutting tools, ~13 % lower. To be able to use the two-color pyrometer technique for temperature measurements in hard turning of AISI 52100 steel, a linear approximation function was determined resulting in three unique equations, one for each of the studied materials and surfaces. By using the developed approximation function, the measured cutting temperatures can be adjusted to compensate for differing materials or surface topographies for comparable machining conditions. Even though the proposed equations are unique for the hard turning conditions as studied here, the proposed methodology can be applied to determine the temperature compensation required for other surface topographies, as well as other materials.     

One problem of the theory of dimensional electrochemical machining of metals

A method is proposed for determining the shape of the anode-article boundary for a given shape of the cathode-tool in plane problems of the theory of dimensional electrochemical machining of metals. Under the assumptions used, the boundary of the anode-article is divided into the working zone, where metal dissolution occurs, and an adjacent zone, where the treatment (dissolution) is terminated. The initial problem is reduced to a problem of a fictitious plane-parallel potential flow of an ideal fluid with a nonlinear condition on the free surface. The point of separation of the fictitious flow from the solid boundary corresponds to the point separating these two zones of the anode boundary. The Brillouin-Will condition of smooth separation is imposed at the separation point to construct a closed system of equations determining the problem solution. __________ Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 50, No. 3, pp. 214–220, May–June, 2009.     

Entropy generation in laser heating in relation to machining

Entropy generation during laser evaporative heating of solid substrate in relation to machining is considered and entropy generation rate due to different pulse intensities is computed. Energy method is used when simulating the phase change process and mushy zone formation across solid–liquid and liquid–vapor interfaces are accommodated. Since the heating duration is greater than the electron relaxation time, the Fourier heating model based on the equilibrium transport is employed in the simulations. Entropy generation in the substrate material is formulated during laser heating pulse. It is found that entropy generation rate in the surface region of the substrate material attains high values. Increasing power intensity ratio enhances the total entropy generation rate in a non-linear fashion.     

聚晶金刚石刀具加工强化复合地板时的切削性能及磨损机理研究

通过对聚晶金刚石刀具加工A1203表层强化复合地板的试验研究，分析了金刚石粒度对聚品金刚石刀具切削性能的影响以及刀具的磨损机理。结果表明：随着金刚石粒度的增大，聚晶金刚石刀具的耐磨性能增强；聚晶金刚石刀具在加工过程中的磨损机理主要表现为具有疲劳磨损特征的沿品断裂及局部解理断裂．品间微裂纹是导致聚晶金刚石刀具磨损的主要因素．     

A new heat transfer analysis in machining based on two steps of 3D finite element modelling and experimental validation

Modelling machining operations allows estimating cutting parameters which are difficult to obtain experimentally and in particular, include quantities characterizing the tool-workpiece interface. Temperature is one of these quantities which has an impact on the tool wear, thus its estimation is important. This study deals with a new modelling strategy, based on two steps of calculation, for analysis of the heat transfer into the cutting tool. Unlike the classical methods, considering only the cutting tool with application of an approximate heat flux at the cutting face, estimated from experimental data (e.g. measured cutting force, cutting power), the proposed approach consists of two successive 3D Finite Element calculations and fully independent on the experimental measurements; only the definition of the behaviour of the tool-workpiece couple is necessary. The first one is a 3D thermomechanical modelling of the chip formation process, which allows estimating cutting forces, chip morphology and its flow direction. The second calculation is a 3D thermal modelling of the heat diffusion into the cutting tool, by using an adequate thermal loading (applied uniform or non-uniform heat flux). This loading is estimated using some quantities obtained from the first step calculation, such as contact pressure, sliding velocity distributions and contact area. Comparisons in one hand between experimental data and the first calculation and at the other hand between measured temperatures with embedded thermocouples and the second calculation show a good agreement in terms of cutting forces, chip morphology and cutting temperature.     

Thermo–elasto–plastic stresses in functionally graded materials under consideration of the fabrication process

Summary  The present study analyzes elasto–plastic thermal stresses in some particle-reinforced functionally graded material plates (FGP) by taking into consideration residual stresses of the fabrication process. For the FGP, the region near the cooling metal surface consists of distributed ceramic particles in a metal matrix, while the region near the heating ceramic surface contains distributed metal particles in a ceramic matrix. We use the thermo–elasto–plastic constitutive equation of a particle-reinforced composite, taking into consideration temperature changes and damage as well as the reinforcing effect of particles. Elasto–plastic thermal stresses are discussed here with the goal of reducing the thermal stresses. Two kinds of particle-reinforced FGP are considered: the first kind (FGP1) represents distributed ceramic particles in the metal matrix, and the second one (FGP2) represents distributed metal particles in the ceramic matrix. We modify the thermo–elasto–plastic constitutive equation of a particle-reinforced composite for the FGP2 by taking into consideration temperature changes and damage as well as the reinforcing effect of particles. Using the temperature-dependent material properties, three cases of temperature conditions are studied. The first one is the cooling from the fabrication temperature to the room temperature, the second one is the heating from the room temperature, and the last one is the heating after cooling from the fabrication temperature. The particle volume fraction is assumed to vary according to a power function in the thickness direction of the FGPs. Using the finite element method, the effects of the distribution parameter of the composition on the macroscopic stress, the stress in the matrix and the stress in the particle in the FGPs are discussed. Also, the effects of the particle volume fraction and the fabrication temperature on the maximum tensile matrix stress are discussed. Received 22 November 2000; accepted for publication 24 April 2001     

Vibration suppression in multi-tool ultrasonic machining to multi-external and parametric excitations

Ultrasonic machining （USM） is of particular interest for the machining of non-conductive, brittle materials such as engineering ceramics. In this paper, a multi-tool technique is used in USM to reduce the vibration in the tool holder and have reasonable amplitude for the tools. This can be done via dynamic absorbers. The coupling of four nonlinear oscillators of the tool holder and tools representing ultrasonic cutting process are investigated. This leads to a four-degree-of-freedom system subjected to multi-external and multi-parametric excitation forces. The aim of this work is to control the tool holder behavior at simultaneous primary, sub-harmonic and internal resonance condition. Multiple scale perturbation method is used to obtain the solution up to the second order approximations. The different resonance cases are reported and studied numerically. The stability of the system is investigated by using both phase-plane and frequency response techniques. The effects of the different parameters of the tools on the system behavior are studied numerically. Comparison with the available published work is reported.     

Shear flow induced interface instability

 A system of two stratified layers at a free surface, consisting of distilled water above a layer of salty water separated by an interface, is studied under laboratory conditions involving uniform temperature heating from below. Shadowgraph and particle images have been used with temperature and salt concentration measurements to investigate the interface instability induced by convection when it is developing in the upper and lower layer. It is found that the interface is governed by local shear flow that induces a Kelvin–Helmholtz instability. Moreover, the entrainment interface is subject to a combination of two closely related effects: (1) double diffusion and convective motion and (2) double diffusion and Kelvin–Helmholtz instability. Received: 22 December 1999/Accepted: 31 October 2000     

微织构刀具正交切削Ti6Al4V的试验研究

仿生摩擦学的出现,为刀具减摩技术提出了新的研究方向,通过钛合金的正交切削试验研究了表面微织构刀具在微量润滑和无润滑剂条件下的减摩性能.结果表明：表面微沟槽在润滑剂条件下可以有效地改善刀屑之间的摩擦,降低切削力与切削温度,同时表面微沟槽还可以改善钛合金的粘结现象;在无润滑剂条件下,微沟槽依然具有一定的＂润滑＂作用.     

开式热沉内冷刀具的设计及其导热性能分析

车削加工温度对工件的表面加工质量和刀具的使用寿命具有重要影响. 设计了一种开式热沉内冷刀具,计算了在实际加工工艺参数下刀具受到的切削力和前刀面上的热流密度,分析了刀具的结构强度;建立了刀具热-流-固耦合温度场模型,探讨了热稳态条件下刀具的温度场分布,以及刀片冷却液流道内热沉数量对刀具导热性能的影响规律,比较了在相同热源条件下开式热沉内冷刀具与其他内冷刀具的导热性能. 结果表明:对于刀片材料为硬质合金YT5的刀具,在热流密度为10 W/mm2的条件下,内置6个热沉的设计方案可获得最佳冷却效果,刀具的最高切削温度控制为187.1 ℃;与其他内冷刀具相比,开式热沉内冷刀具的最高切削温度降低了12.1 ℃.      

Design and Modeling for Chatter Control

Boring bars for single-point turning on a lathe are particularly susceptible to chatter and have been the subject of numerous studies. Chatter is, in general, caused by instability. Clearly, the cutting process can be limited to regions of known stable operation. However, this severely constrains the machine-tool operation and causes a decrease in productivity. The more aggressive approach is to attack the stability problem directly through application of vibration control. Here, we demonstrate a new biaxial vibration control system (VPI Smart Tool) for boring bars. We present the experimentally determined modal properties of the VPI Smart Tool and demonstrate how these properties may be used to develop models suitable for chatter stability analysis, simulation, and development of feedback compensation. A phenomenological chatter model that captures much of the rich dynamic character observed during experiments is presented. We introduce the notion that the mean cutting force changes direction as the width of cut increases due to the finite nose radius of the tool. This phenomenon is used to explain the progression from chatter that is dominated by motions normal to the machined surface at small widths of cut to chatter that is dominated by motions tangential to the machined surface at large widths of cut. We show experimental evidence to support our assertion that a biaxial actuation scheme is necessary to combat the tendency of the tool to chatter in both directions. We then present some preliminary theoretical results concerning the persistence of subcritical instability as we expand consideration to high-speed machining.     

高速车削钛合金的硬质合金刀具磨损机理研究

使用硬质合金刀具材料进行钛合金(Ti-6Al-4V)的高速干车削试验.采用电子扫描显微镜(SEM)观察刀具的磨损形貌,通过能谱分析(EDS)分析磨损表面的元素分布,并对刀具的主要磨损机理进行了分析.研究结果表明,使用硬质合金刀具材料高速干车削Ti-6Al-4V时,刀具的磨损机理主要为粘结磨损、氧化磨损和扩散磨损.硬质合金刀具的氧化磨损主要发生在刀具前刀具和后刀面的磨损边缘区.由于车削过程中刀具前刀面的切削温度比后刀面的切削温度高,导致刀具前刀面的氧化磨损、粘结磨损和扩散磨损较后刀面严重.     

Modélisation du comportement thermique d'un outil de fraisage : approche par identification de système non entier

In this work we present an experimental apparatus devoted to the thermal characterisation of a milling tool. The experimental device used thermistors, one for each insert. Each thermistor is located at a point in the tool close to the tip of the insert. The heat flux in each insert is expressed according to the temperature at the sensor from a non-integer model. The parameters of the model are identified from transient evolutions measurements of the temperature on the sensor and on the cutting edge. An application shows the difference in the behaviour of each insert during machining from the estimated heat fluxes. To cite this article: J.-L. Battaglia et al., C. R. Mecanique 330 (2002) 857–864.     

Measurement of Residual Stresses in Nuclear-grade Zircaloy-4(R) Tubes—Effect of Heat Treatment

Nuclear-grade Zircaloy-4(R) tubes are produced by a unique manufacturing process known as pilgering, which leaves the material in a work-hardened state containing a pattern of residual stresses. Moreover, such tubes exhibit elastic anisotropy as a result of the pilgering process. Therefore, standard equations originally proposed by Sachs (Z Met Kd, 19: 352–357, 1927; Sachs, Espey, Iron Age, 148: 63–71, 1941). for isotropic materials do not apply in this situation. Voyiadjis et al. (Exp Mech, 25: 145–147, 1985) proposed a set of equations for treating elastically anisotropic materials, but we have determined that there are discrepancies in their equations. In this paper, we present the derivation for a set of new equations for treating elastically anisotropic materials, and the application of these equations to residual stress measurements in Zr-4(R) tubes. To this end, through thickness distribution of residual stress components in as-received and heat treated (500°C) Zr-4(R) tubes was measured employing the Sachs’ boring-out technique in conjunction with electrochemical machining as the means of material removal, and our new equations. For both as-received and the heat treated materials, the axial and tangential residual stresses were significantly higher than the radial and shear residual stresses. The largest residual stress was the tangential stress component in the as-received material, showing a tensile value at the outer surface and a compressive value at the inner surface. At high values of von Mises equivalent stress, the principal directions of residual stress coincided with the principal axes of the tube for the as-received material, as well as for the material heat treated at 500°C.     

Edge Finishing Effects on the Impact Behavior of Chopped GFRP Composites

The low velocity and low energy impact response of two common sheet mold compound (SMC) material systems—SMC-R27, and SMC-R37—were investigated. In addition to characterizing the low velocity impact response and failure progression of the material systems, the edge effects of diamond saw cutting, waterjet cutting and abrasive waterjet cutting were investigated using optical microscopy and contact surface profilometry. Impact force–time and displacement–time responses were measured and used to characterize energy absorption capabilities and potential correlation to post processing operation and fiber volume fraction. Pre and post-impact edge surface micrographs were examined to relate the failure behavior on the machined surfaces. Experiments and measurements all show that the failure zone size and growth behavior are clearly dependent on the edge finishing process.     

Optimization of cutting conditions for end milling of Ti6Al4V Alloy by using a Gravitational Search Algorithm (GSA)

Surface roughness is commonly used to indicate the quality of machine parts. Optimizing cutting parameters throughout the machining process is an important aspect for manufacturers, as it allows them to achieve a minimum surface value. During this study, a new optimization technique known as the gravitational search algorithm (GSA) was employed in order to achieve minimum surface roughness when end milling a Ti6Al4V alloy under dry cutting conditions, with both PVD coated and uncoated cutting tools. Regression models have been created based on the results of real experimental data. Through use of SPSS software, it was possible to formulate the objective (fitness) functions which were used in the GSA optimization for each cutting tool. A MATLAB code was then created to instigate the optimization process. The results indicated that high cutting speed and low feed rate and depth of cut could result in a minimum surface roughness value of (0.6255 μm), based on the objective function for the PVD cutting tool. Alternatively, surface roughness of around (0.4165 μm) could be achieved by using an uncoated tool on a lower feed rate, depth of cut and cutting speed. The same GSA technique was used in another case study optimized by Genetic algorithm (GA). The GSA achieved the same results, and proved that it is faster than GA: GSA could reach the optimum solution in the third iteration; GA could only reach it in the 67th.     

Modélisation du comportement thermique d'un outil de fraisage : approche par identification de système non entierThermal modelling of a milling tool: a noninteger system identification approach

In this work we present an experimental apparatus devoted to the thermal characterisation of a milling tool. The experimental device used thermistors, one for each insert. Each thermistor is located at a point in the tool close to the tip of the insert. The heat flux in each insert is expressed according to the temperature at the sensor from a non-integer model. The parameters of the model are identified from transient evolutions measurements of the temperature on the sensor and on the cutting edge. An application shows the difference in the behaviour of each insert during machining from the estimated heat fluxes. To cite this article: J.-L. Battaglia et al., C. R. Mecanique 330 (2002) 857–864.