Determination of metals, metalloids and non-volatile ions in airborne particulate matter by a new two-step sequential leaching procedure Part B: Validation on equivalent real samples

Due to the lack of proper standard materials for airborne particulate matter collected on filters, a validation scheme was developed, which is here described, to the aim of testing the application of leaching procedures performing both ions and elemental determinations on real samples of airborne particulate matter collected on filters. The scheme has been developed on a two-step leaching method (extraction in acetate buffer and acid dissolution of residue) previously developed by authors and consists of two series of tests to be run on n pairs of equivalent parallel samples filter-collected. The first series of tests aims to assess on real samples the equivalence between results obtained by the tested procedure with those obtained by the EMEP ions extraction and the EN 12341 standard methods, whereas the second aims to evaluate the reproducibility of analytical results of elemental determination in the leached and dissolved fractions; in the latter case data reliability is also evaluated as a function of the environment-intrinsic variability of real samples.To avoid errors due to sampling differences data from filter pairs were standardized both by gravimetric determination of loaded filters, according to the EN 12341 standard and by the rate [SO₄²⁻]_A/[SO₄²⁻]_B, where [SO₄²⁻] indicate the soluble sulphate concentration in the extract; in the latter case values improved for all elements and in both fractions. Results of equivalence with standard methods and reproducibility tests are evaluated as mean relative percentage differences (Δ%) and percentage elements recoveries (R%). The application of the validation scheme to the two-step leaching method is here discussed for non-volatile ions and for 17 elements detected on 22 pairs of low-volume collected PM₁₀ samples on Teflon filters.     

Determination of water soluble trace metals in airborne particulate matter using a dynamic extraction procedure with on-line inductively coupled plasma optical emission spectrometric detection

A novel continuous-flow system for the dynamic extraction of water soluble metal fractions in airborne particulate matter (APM) with subsequent inductively coupled plasma optical emission spectrometric (ICP-OES) analysis of derived extracts is presented. The fully automated extraction system with on-line multi-element detection offers enhanced sensitivity when compared to batch-wise counterparts; additionally it provides information about the extraction process. With the developed procedure detection limits in the order of 1.5 (Ba) to 8.0 (Ni) ng extractable mass per investigated sample could be achieved, which translates to method detection limits for soluble metal concentrations in APM ranging from 0.2 ng m⁻³ (Ba) to 0.9 ng m⁻³ (Fe). Reproducibility of analysis was determined by replicate measurement (n = 6) of an APM sample with an aerodynamic diameter ≤10 μm (PM10), derived results varied between 3.5% (Mn) and 12.1% (Ni) relative standard deviation. Method validation was accomplished by comparison of extracted soluble and remaining non-soluble fractions with the total metal contents of the investigated PM10 samples, showing an excellent mass balance for all elements. Application of the developed procedure for the analysis of water soluble metal fractions in PM10 samples (n = 16) from Linz (Austria) indicated a high variability of extractable fractions ranging from 11.7 ± 7.2% (Fe) to 48.8 ± 15.4% (Mn) of the total metal contents.     

Determination of water-soluble and insoluble compounds in size classified airborne particulate matter

The elemental composition of water soluble and acid soluble size-fractionated airborne particulate matter (APM) was investigated. PM2.5 and PM2.5-10 samples were collected every three days from October 2006 to October 2007 in Buenos Aires, Argentina. The collection was performed on Nucleopore® filters using a GENT sampler. Samples containing fine and coarse particles were subjected to an aqueous leaching to obtain information on the dissolution behaviors of ions, metal and metalloids. Key elements namely, Al, Ba, Ca, Cr, Cu, Fe, Mg, Mn, Pb, Se, Ti and Zn were determined in each fraction by inductively coupled plasma optical emission spectrometry (ICP OES). In the aqueous fractions, Cl⁻, SO₄²⁻, Na⁺ and NH₄⁺ were determined by high performance liquid chromatography (HPLC). A (6:2:5) mixture of nitric, hydrochloric and perchloric acids was used for leaching metals from the residual filters. For validation of the extraction procedure, the ICP OES measurements the Standard Reference Material NIST 1648 (Urban particulate matter) was subjected to the same analytical procedure that the samples loaded with APM. Total analyte concentration varied from 333.2 μg g^− 1 (equivalent to 3.7 ng m^− 3) for Ti to 692 mg g^− 1 (equivalent to 2.47 μg m^− 3) for Ca.     

Multi-element analysis of airborne particulate matter by various spectrometric methods after microwave digestion

A microwave digestion procedure in combination of the measurement of various spectrometric methods including atomic absorption spectrometry, inductively coupled plasma atomic emission spectrometry and inductively coupled plasma mass spectrometry was developed for the multi-element analysis of airborne particulate matter collected on PTFE filters by a dichotomous sampler. In order to achieve more sensitive and rapid multi-element analyses, special PTFE-lined digestion vessels were used. It was found that complete digestion of airborne particulates with an acid mixture of HNO₃-HClO₄-HF (3:7:1, v/v) can be achieved in the microwave-irradiated closed vessel system and direct spectroscopic measurement of the digested sample after appropriate dilution. A recovery study was conducted using a multi-element standard and NIST Standard Reference Material 1648 Urban Particulate. Sixteen major, minor, and trace elements in airborne particulate matter were determined.     

Inductively coupled plasma optical emission spectrometric determination of trace element in PM10 airborne particulate matter collected in an industrial area of Argentina

Trace metals of relevance from the environmental and toxicological point of view were quantified in the city of Campana, Buenos Aires, Argentina. The collection of particulate matter was performed on ash-free fiber glass filters using high-volume samplers with a PM₁₀ sampling head, during a 3-month period in 2002. An acid leaching of elements deposited on the filters was adopted paying special attention to the recovery of volatile elements. Analysis was performed by inductively coupled plasma optical emission spectrometry (ICP OES) to ascertain the concentrations of 12 key elements, namely, Al, As, Cd, Cr, Cu, Fe, Mn, Ni, Pb, Ti, V and Zn. The validation of the procedure was performed by the analysis of the standard reference material NIST 1648, urban particulate matter, and good agreement between concentrations found and the reported certified values was achieved. Blank filters were spiked with the analytes investigated and the recoveries varied between 83% and 92%. Metal concentrations spanned the range 0.03 ng m⁻³ (equivalent to 0.42 μg g⁻¹) for Cd to 1.9 μg m⁻³ (equivalent to 29.7 mg g⁻¹) for Fe. The results obtained show that the pollutants of special environmental and health concern are As and Pb. Mean As concentration was higher than the guideline value associated with an excess cancer risk of 1:10⁻⁶, reported by the World Health Organization (WHO). Lead is the only element that showed higher concentrations than those recently measured in the large and heavily trafficked metropolitan area of Buenos Aires. Cadmium>Pb>As>Zn>Cu are the elements more enriched in airborne PM₁₀.     

Analytical methods for assessing metal bioaccessibility in airborne particulate matter: A scoping review

In contrast to the existence of standardized methods to assess metal bioaccessibility via the gastrointestinal route, there are no widely-accepted, established in vitro testing protocols to measure elemental solubility in the human lung. This may be attributed, in part, to the difficulty associated with simulating the lung’s complex in vivo conditions. The purpose of this review is two-fold: (1) to determine how the bioaccessibility of metals associated with ambient particulate matter (PM) in the human lung has been assessed in the literature, and (2) examine the suitability and biological relevance of applied methods for the measurement of metal bioaccessibility employed to date.     

Determination of platinum in urine and airborne particulate matter from Budapest and Vienna

Urine samples taken from 100 adults living in the city centres of the two capitals were analysed by the same inductively coupled plasma quadrupole mass spectrometer following their 10-fold dilution with bidistilled water. The mean concentration values of platinum related to creatinine were about three times higher in the Hungarian samples than in the Austrian ones. Six particulate matter samples were collected by a Gent-type two-stage sampler in the districts of the two capitals, which have high traffic density. The polycarbonate filters containing the fine (d<2 μm) and the coarse (d=2–10 μm) fractions were digested in a microwave assisted digestion system and analysed by the same high-resolution inductively coupled plasma mass spectrometer. The respirable, fine fractions of aerosols collected in Budapest contained approximately twice as much platinum than the aerosols from Vienna. However, the coarse fraction showed a contrary picture, with five times higher Pt concentration in the samples collected in Vienna.     

Fractionation of heavy metals in sediment by using microwave assisted sequential extraction procedure and determination by inductively coupled plasma mass spectrometry

In this work, a fast microwave assisted extraction procedure was developed and optimized for the heavy metals (Cu, Ni, Cr, Pb and Cd) partitioning in the three-stage sequential extraction procedure proposed by the European Standards, Measurements and Testing (SM&;T) Program, formerly the Community Bureau of Reference (BCR). The microwave oven procedure was optimized to obtain extraction efficiencies similar to the conventional BCR procedure, in less time, while using smaller volumes of reagents. In the optimization process, three variables (extraction time, ramping time and microwave power) were considered as factors and as a response the concentration of different metal ions in each individual BCR fraction. Interactions between analytical factors and their optimized levels were investigated using a central composite design. Extractable metals obtained by both comparable methodologies were measured by inductively coupled plasma mass spectrometry. With the use of optimal microwave conditions, steps 1–3 of the sequential extraction (including the hydrogen peroxide digestion in step 3) could be completed between 21 and 22 min. Detection limits were between 1 and 18 ng l^{− 1}. The accuracy of the proposed method was checked with a certified reference material (CRM) of Lake Sediment BCR 701. Values obtained were in accordance with those reported for the certified material with only a few exceptions. Different origin sediments (river and marine) were analyzed by both BCR and MW procedures, and the results obtained were comparable according to the t-paired-test for a 95% confidence level.     

A study of uniformity of elements deposition on glass fiber filters after collection of airborne particulate matter (PM-10), using a high-volume sampler

A study was conducted to evaluate the homogeneity of the distribution of metals and metalloids deposited on glass fiber filters collected using a high-volume sampler equipped with a PM-10 sampling head. The airborne particulate matter (APM)-loaded glass fiber filters (with an active surface of about 500 cm²) were weighed and then each filter was cut in five small discs of 6.5 cm of diameter. Each disk was mineralized by acid-assisted microwave (MW) digestion using a mixture of nitric, perchloric and hydrofluoric acids. Analysis was performed by axial view inductively coupled plasma optical emission spectrometry (ICP OES) and the elements considered were: Al, As, Cd, Cr, Cu, Fe, Mn, Ni, Pb, Sb, Ti and V. The validation of the procedure was performed by the analysis of the standard reference material NIST 1648, urban particulate matter. As a way of comparing the possible variability in trace elements distribution in a particular filter, the mean concentration for each element over the five positions (discs) was calculated and each element concentration was normalized to this mean value. Scatter plots of the normalized concentrations were examined for all elements and all sub-samples. We considered that an element was homogeneously distributed if its normalized concentrations in the 45 sub-samples were within ±15% of the mean value ranging between 0.85 and 1.15. The study demonstrated that the 12 elements tested showed different distribution pattern. Aluminium, Cu and V showed the most homogeneous pattern while Cd and Ni exhibited the largest departures from the mean value in 13 out of the 45 discs analyzed. No preferential deposition was noticed in any sub-sample.     

Recent developments in assessment of bio-accessible trace metal fractions in airborne particulate matter: A review

In the last years a great deal of research has been focused on the determination of harmful trace metals such as Cd, Co, Cr, Cu, Ni or Pb in airborne particulate matter (APM). However, the commonly applied determination of total element concentrations in APM provides only an upper-end estimate of potential metal toxicity. For improved risk assessment it is important to determine bio-accessible concentrations instead of total metal contents. The present review gives an overview of analytical procedures reported for measurement of bio-accessible trace metal fractions in APM. The different approaches developed for extraction of soluble trace metals in APM are summarized. Furthermore the analytical techniques applied for accurate determination of dissolved trace metals in the presence of complex sample matrix are presented. Finally a compilation of published results for bio-accessible trace metals in APM is included.     

A new approach for determination of crustal and trace elements in airborne particulate matter

An ICP-OES procedure was developed for fast and accurate determination of various crustal (Al, Ca, Fe, Mg, Si) and trace elements (Ba, Cu, Mn, Na, K, Sr, Ti, Zn) in airborne particulate matter. The method is based on a preliminary treatment of the aerosol samples with a mixture of nitric acid and hydrogen peroxide at elevated temperature leading to a mineralization of the organic sampling substrate, dissolution of soluble material and homogeneous suspension of the remaining non-soluble fraction. After dilution the derived slurry solutions were measured using ICP-OES. The reproducibility of analysis given as the relative standard deviation (% RSD) varied between 3.2 and 6.8% for bulk constituents such as Al, Ca, Fe, Mg and Si whereas values ranging from 3.5 to 9.1% were obtained for trace metals present with distinctly lower abundance in PM10 (e.g. Ba, Cu, Mn, Sr, Zn). The limits of detection (LOD) calculated as three times the standard deviation (3σ) of the signal derived from filter blank samples ranged from approximately 1?ng?m^?3 (Sr) to 71?ng?m^?3(Ca). The developed procedure was evaluated by comparing the obtained results with the findings derived for the same set of aerosol samples analyzed using a microwave procedure for sample dissolution with subsequent ICP-OES analysis. Finally the developed procedure was applied for the analysis of crustal and trace elements in PM10 samples collected at an urban site (Getreidemarkt, Vienna) and a rural site (Hartberg, Styria), in Austria. The concentrations of the investigated crustal elements varied between some hundred ng?m^?3 and few µg?m^?3 with highest concentrations for Fe and Si, distinctly reduced concentrations ranging from some ng?m^?3 (Sr) to more than hundred ng?m^?3 (K) were found for trace elements. Observed PM10 concentrations were found to be in accordance to literature findings from urban sites in central Europe.     

Determination of Pb in airborne particulate matter with a heavy matrix of silicon by SR-ETAAS

A study is undertaken to monitor Pb levels in airborne particulate matter collected on ash-free glass-fibre filters from urban and industrial areas of Argentina by electrothermal atomic absorption spectrometry with self-reversal background correction. For this sample with a heavy matrix of silicon, a simple acid treatment with aqua regia and HF is proposed aimed to minimize contamination and reduce sample treatment steps. Ultrasonic agitation was employed for sample homogenization. To overcome the problem of the high amounts of Si, main analytical variables including acid pretreatment conditions, temperature program of the graphite furnace and spectroscopic conditions were carefully studied and optimized. Continuum source and self-reversal methods for background correction were compared in order to avoid non-specific and spectral interferences due to the matrix. After optimization, synthetic acid solutions of Pb were employed for calibration. Calibration was linear within the range 1–40 µg L^{− 1} (correlation coefficient of 0.9995) when the 283.3 analytical line was used. Using optimized conditions limits of detection (3σ) of 0.6 µg L^{− 1} were achieved. The repeatability between injections (S_r%) was evaluated and was better than 4.2%. The precision (%RSD) for Pb determination in a single sample was estimated by analyzing three strips of the same filter. In all cases the RSD was better than 6.9%. For checking accuracy, an aliquot of a Standard Reference Material (NIST 2709, San Joaquin Soil) was subject to the same sample treatment and included in the overall analytical process. This method was successfully applied to the determination of Pb in airborne particulate matter collected in Buenos Aires city.     

Determination of mercury in airborne particulate matter collected on glass fiber filters using high-resolution continuum source graphite furnace atomic absorption spectrometry and direct solid sampling

A study has been undertaken to assess the capability of high-resolution continuum source graphite furnace atomic absorption spectrometry for the determination of mercury in airborne particulate matter (APM) collected on glass fiber filters using direct solid sampling. The main Hg absorption line at 253.652 nm was used for all determinations. The certified reference material NIST SRM 1648 (Urban Particulate Matter) was used to check the accuracy of the method, and good agreement was obtained between published and determined values. The characteristic mass was 22 pg Hg. The limit of detection (3σ), based on ten atomizations of an unexposed filter, was 40 ng g^− 1, corresponding to 0.12 ng m^− 3 in the air for a typical air volume of 1440 m³ collected within 24 h. The limit of quantification was 150 ng g⁻¹, equivalent to 0.41 ng m⁻³ in the air. The repeatability of measurements was better than 17% RSD (n = 5). Mercury concentrations found in filter samples loaded with APM collected in Buenos Aires, Argentina, were between < 40 ng g⁻¹ and 381 ± 24 ng g⁻¹. These values correspond to a mercury concentration in the air between < 0.12 ng m⁻³ and 1.47 ± 0.09 ng m⁻³. The proposed procedure was found to be simple, fast and reliable, and suitable as a screening procedure for the determination of mercury in APM samples.     

Optimization and validation of a low temperature microwave-assisted extraction method for analysis of polycyclic aromatic hydrocarbons in airborne particulate matter

A low temperature microwave-assisted extraction method (MAE) is reported for the analysis of polycyclic aromatic hydrocarbons (PAHs) in airborne particulate matter (PM). The main parameters affecting the extraction efficiency (choice of extractants, microwave power, and extraction time) were investigated and optimized. The optimized procedure requires a 20 ml mixture of acetone:n-hexane (1:1) for extraction of PAHs in PM at 150 W of microwave energy (20 min extraction time). Clean-up of MAE extracts was not found to be necessary. The optimized method was validated using two different SRM (1648-urban particulate matter and 1649a, urban dust). The results obtained are in good agreement with certified values. PAHs recoveries for both reference materials were between 79 and 122% with relative standard deviation ranging from 3 to 21%. Detection limits were determined based on blank determination using two kinds of quartz filter substrates (n = 10), which ranged from 0.001 (0.03) ng m⁻³ (pg/μg) for B(k)Ft to 1.119 (37.3) for Naph in ng m⁻³ (pg/μg), respectively. The repeatability and day-to-day reproducibility obtained in this study were in the range of 4-16 and 3-25% for spiked standards and SRM 1649, respectively. The optimized and validated MAE technique was applied to the extraction of PAHs from a set of real world PM samples collected in Singapore. The sum of particulate-bound PAHs in outdoor PM ranged from 1.05 to 3.45 ng m⁻³ while that in indoor PM (cooking emissions) ranged from 27.6 to 75.7 ng m⁻³, respectively.     

Bioaccessibility of selected trace metals in urban PM<Subscript>2.5</Subscript> and PM<Subscript>10</Subscript> samples: a model study

Bioaccessibility of trace metals originating from urban particulate matter was assessed in a worst case scenario to evaluate the uptake and thus the hazardous potential of these metals via gastric juice. Sampling was performed over a period of about two months at the Getreidemarkt in downtown Vienna. Concentrations of the assayed trace metals (Ti, Cr, Mn, Co, Ni, Cu, Zn, Mo, Ag, Cd, Sn, Sb, Tl and Pb) were determined in PM_2.5 and PM₁₀ samples by ICP-MS. The metal concentrations in sampled air were in the low picogram to high nanogram per cubic metre range. The concentrations in PM_2.5 samples were generally lower than those in PM₁₀ samples. The average daily intake of these metals by inhalation for a healthy adult was estimated to be in the range of <1 ng (Tl) to >1,000 ng (Zn). To estimate the accessibility of the inhaled and subsequently ingested metals (i.e. after lung clearance had taken place) in the size range from 2.5- to 10-μm aerodynamic equivalent diameter, a batch-extraction with synthetic gastric juice was performed. The data were used to calculate the bioaccessibility of the investigated trace metals. Extractable fractions ranged from 2.10% (Ti in PM_2.5) to 91.0% (Cd in PM_2.5), thus yielding bioaccessible fractions (PM_2.5–10) from 0.16 ng (Ag) to 178 ng (Cu).     

Detection of PAH of molecular weight between 300 and 402 in airborne particulate matter by fused silica capillary GC and GC/MS

Gas chromatography (GC), low-voltage mass spectrometry (LV MS), and gas chromatography/mass spectrometry (GC/MS) have been used for detecting polycyclic aromatic hydrocarbons (PAH) of molecular weight between 300 and 402 in airborne particulate matter. Nearly 200 high molecular PAH separated by fused silica capillary columns could be characterized by their El mass spectra. The lack of reference substances precluded further structure elucidation.     

Simultaneous determination of suspended particulate trace metals (Co, Ni, Cu, Zn, Cd and Pb) in seawater with small volume filtration assisted by microwave digestion and flow injection inductively coupled plasma mass spectrometer

A new technique for the determination of suspended particulate trace metals (P-metals >0.2 μm), such as Co, Ni, Cu, Zn, Cd and Pb, in open ocean seawater has been developed by using microwave digestion coupled with flow injection inductively coupled plasma mass spectrometry (FI-ICP-MS). Suspended particulate matter (SPM) was collected from 500 mL of seawater on a Nuclepore filter (0.2 μm) using a closed filtration system. Both the SPM and filter were completely dissolved by microwave digestion. Reagents for the digestion were evaporated using a clean evaporation system, and the metals were redissolved in 0.8 M HNO₃. The solution was diluted with buffer solution to give pH 5.0 and the metals were determined by FI-ICP-MS using a chelating adsorbent of 8-hydroxyquinoline immobilized on fluorinated metal alkoxide glass (MAF-8HQ). The procedure blanks with a filter were found to be 0.048 ± 0.008, 10.3 ± 0.3, 0.27 ± 0.05, 3.3 ± 1.8, 0.02 ± 0.03 and 0.85 ± 0.09 ng L⁻¹ for Co, Ni, Cu, Zn, Cd and Pb, respectively (n = 14). Detection limits defined as 3 times the standard deviation of the blanks were 0.023, 0.90, 0.14, 5.3, 0.078 and 0.28 ng L⁻¹ for Co, Ni, Cu, Zn, Cd and Pb, respectively. Accuracy was evaluated using certified reference materials of chlorella (NES CRM No. 3) and marine sediment (HISS-1). The method was applied to the determination of vertical distributions for P-Co, Ni, Cu, Zn, Cd and Pb in the Western North Pacific.     

Microwave digestion-ICP-MS for elemental analysis in ambient airborne fine particulate matter: rare earth elements and validation using a filter borne fine particle certified reference material

NIST standard reference material SRM 2783 was employed to validate a high temperature, high pressure, two-stage microwave assisted acid digestion procedure using HNO₃, HF and H₃BO₃ developed for the analysis of trace elements (including rare earths) in atmospheric fine particulate matter (PM_2.5) prior to inductively coupled plasma mass spectrometry (ICP-MS). This method quantitatively solubilized Na, Mg, Al, K, Ti, V, Mn, Fe, Co, Ni, Cu, Zn, As, Se, Rb, Sb, Cd, Cs, Ba, Pb, Th, U and several rare earth elements (REEs) (La, Ce, Pr, Nd, Gd, Dy, Er, Sm and Eu) from SRM 1648 and SRM 2783. A small amount of HF in the first stage was required to dissolve silicates necessitating the corresponding addition of H₃BO₃ in second stage to dissolve fluoride precipitates of Mg, La, Ce and Th. The optimized microwave dissolution—ICP-MS method detected Na, Mg, Al, K, Ti, V, Mn, Fe, Co, Ni, Cu, Zn, As, Se, Rb, Sr, Cd, Mo, Sb, Cs, Ba, La, Ce, Pr, Nd, Sm, Gd, Pb, Th and U at trace to ultra-trace levels in ambient airborne fine particles from three sites in North Carolina. La to light lanthanide signature ratios suggested that soil and motor vehicles are the dominant REE sources in SRM 2783 and PM_2.5 samples collected during this study.     

利用多功能LB-HG型雾化氢化物发生器与电感耦合等离子体原子发射光谱联用测定人发中砷、锑、汞、铅

采用多功能ＬＢ－ＨＧ型雾化氢化物发生器与ＩＣＰ－ＡＥＳ联用，测定砷、锑、铅。较传统的气动雾化法，检出限降低了１０～１００倍。标准人发样品的分析结果与推荐值相吻合。     

Determination of soluble ions and elements in ambient air suspended particulate matter: Inter-technique comparison of XRF, IC and ICP for sample-by-sample quality control

In this paper, we describe a validation procedure for chemical fractionation analysis of elements (Al, As, Ba, Ca, Cd, Cr, Cu, Fe, K, Mg, Mn, Na, Ni, Pb, S, Sb, Si, Sr, Ti and V) and soluble ions (Cl⁻, NO₃⁻, SO₄²⁻, Na⁺, NH₄⁺, Mg²⁺, Ca²⁺) in suspended particulate matter (PM). The procedure applies three distinct measurement techniques (XRF, IC and ICP-OES) to the analysis of individual samples. The techniques used generate different outputs at different stages in the procedure. This makes it possible to identify the contributions of specific parameters to measurement uncertainty. On this basis, we propose a scheme for controlling the analytical quality of data from individual samples in which inter-technique comparisons is used in the same way many analytical methods use surrogates. We apply this scheme to about 310 samples of PM₁₀ and PM_2.5 identifying and assessing the main factors contributing to measurement uncertainty. This procedure successfully resolved a number of difficulties frequently encountered during the analysis of PM, including lack of appropriate reference materials and the low reliability of alternative techniques of quality control. The results demonstrate the critical importance of sample treatment prior to destructive analysis by IC and ICP.