Highly sensitive and selective amperometric sensors for nanomolar detection of iodate and periodate based on glassy carbon electrode modified with iridium oxide nanoparticles

Iridium oxide nanoparticles are grown on a glassy carbon electrode by electrodepositing method. The electrochemical behavior and electrocatalytic activity of modified electrode towards reduction of iodate and periodate are studied. The reductions of both ions occur at the unusual positive peak potential of 0.7 V vs. reference electrode. The modified electrode is employed successfully for iodate and periodates detection using cyclic voltammetry, hydrodynamic amperometry and flow injection analysis (FIA). In the performed experiments, flow injection amperometric determination of iodate and periodate yielded calibration curves with the following characteristics: linear dynamic range up to 100 and 80 μM, sensitivity of 140.9 and 150.6 nA μM⁻¹ and detection limits of 5 and 36 nM, respectively. The repeatability of the modified electrode for 21 injections of 1.5 μM of iodate solution is 1.5%. The interference effects of NO₂⁻, NO₃⁻, ClO₃⁻, BrO₃⁻, ClO₄⁻, SO₄²⁻, Cu²⁺, Zn²⁺, Mn²⁺, Mg²⁺, Cd²⁺, Ca²⁺, Na⁺, K⁺, NH₄⁺ and K⁺, CH₃COO⁻ and glucose were negligible at the concentration ratio of more than 1000. The obtained attractive analytical performance together with high selectivity and simplicity of the proposed method provide an effective and e novel modified electrode to develop an iodate and periodate sensor. Sensitivity, selectivity, the liner concentration range and the detection limit of the developed sensor are all much better than all known similar sensors in the literature for iodate and periodate determination.     

Modification of glassy carbon electrode with a polymer/mediator composite and its application for the electrochemical detection of iodate

A modified glassy carbon electrode was prepared by depositing a composite of polymer and mediator on a glassy carbon electrode (GCE). The mediator, flavin adenine dinucleotide (FAD) and the polymer, poly(3,4-ethylenedioxythiophene) (PEDOT) were electrochemically deposited as a composite on the GCE by applying cyclic voltammetry (CV). This modified electrode is hereafter designated as GCE/PEDOT/FAD. FAD was found to significantly enhance the growth of PEDOT. Electrochemical quartz crystal microbalance (EQCM) analysis was performed to study the mass changes in the electrode during the electrodeposition of PEDOT, with and without the addition of FAD. The optimal cycle number for preparing the modified electrode was determined to be 9, and the corresponding surface coverage of FAD (Γ_FAD) was ca. 5.11 × 10⁻¹⁰ mol cm⁻². The amperometric detection of iodate was performed in a 100 mM buffer solution (pH 1.5). The GCE/PEDOT/FAD showed a sensitivity of 0.78 μA μM⁻¹ cm⁻², a linear range of 4–140 μM, and a limit of detection of 0.16 μM for iodate. The interference effects of 250-fold Na⁺, Mg²⁺, Ca²⁺, Zn²⁺, Fe²⁺, Cl⁻, NO₃⁻, I⁻, SO₄²⁻ and SO₃²⁻, with reference to the concentration of iodate were negligible. The long-term stability of GCE/PEDOT/FAD was also investigated. The GCE/PEDOT/FAD electrode retained 82% of its initial amperometric response to iodate after 7 days. The GCE/PEDOT/FAD was also applied to determine iodate in a commercial salt.     

Gas diffusion-flow injection determination of total inorganic carbon in water using tungsten oxide electrode

A novel gas diffusion-flow injection method has been developed for the rapid and sensitive determination of total inorganic carbon (TIC) in water. The method is based on the diffusion of CO₂ across gas permeable membrane from a donor stream containing 0.1 M HCl to an acceptor stream of sodium acetate (10⁻⁵ mol l⁻¹ and pH 10). The CO₂ trapped in the acceptor stream passes through an electrochemical flow cell contains a tungsten oxide wire and a silver/silver chloride electrode, where it was sensitively detected. The parameters affecting the sensitivity of the electrode such as buffer concentration, pH, flow rate and injected volume were studied in detail. The electrode response was linear in the concentration range from 5 to 100 μg ml⁻¹ CO₃²⁻ with a correlation coefficient (R²) of 0.998. Precision (R.S.D.) was 1.42% for 20 μg ml⁻¹ standard solution of CO₃²⁻ (n=10). The detection limit was 0.20 μg ml⁻¹ CO₃²⁻. The method was evaluated by the injection of real natural water samples and an average recovery of 100.1% was obtained. The sampling rate was 30 samples h⁻¹. The method is simple, feasible with satisfactory accuracy and precision and thus could be used for monitoring TIC in water.     

Flow injection potentiometric detection of trimethylamine in seafood using tungsten oxide electrode

A simple flow injection gas/diffusion method for the determination of trimethylamine (TMA) in seafood with potentiometric detection using tungsten oxide electrode has been developed. The method is based on the diffusion of TMA through a PTFE membrane from a sodium hydroxide donor stream to a phosphate buffer acceptor stream. The TMA in the acceptor stream passes through an electrochemical flow cell containing a tungsten oxide wire and a silver/silver chloride electrode, where TMA was sensitively detected. The parameters affecting the sensitivity of the electrode such as sodium hydroxide concentration, buffer concentration, pH, flow rate and injected volume were studied in details. The electrode response was linear in the concentration range from 1 to 10 μg ml⁻¹ TMA with a correlation coefficient (R²) of 0.991 and a detection limit of 0.05 μg ml⁻¹ TMA. The intra- and inter-days precision (R.S.D.) was found to be, respectively, 1.20 and 1.6% (n=6). The method was applied to the determination of TMA in fish tissue and recoveries of 99-100% were obtained for fish extracts. Results were in close agreement with those obtained by the existing classical official method. Common interference from those species that can diffuse through the membrane were removed by the addition of formaldehyde to the seafood extract. The method is simple, feasible with satisfactory accuracy and precision and thus, could be used for monitoring seafood quality with a sampling rate of 20±2 sample h⁻¹.     

Model of electrochromic and related phenomena in tungsten oxide thin films

We have developed a model of electrochromic and related phenomena in tungsten oxide thin films based on the assumption that the constitution of such films is heterogeneous and built up of nanosized particles, pores and adsorbed substances (mainly water). It is discussed why a high-efficiency reversible blue colour is observed in amorphous tungsten oxide films (α-WO₃ films) as well as why such porous thin films with polycrystalline or amorphous constitution and with a variety of particle properties can be easily obtained by a physical vapour deposition process in a low-pressure atmosphere in the presence of water. A substrate temperature in the range 450–550 K corresponds to some plateau on the water desorption curves which divided physically adsorbed water from chemically adsorbed water. Two types of structural units based on tetrahedrally and octahedrally coordinated tungsten ions have the main role in the formation of the film constitution. The tetrahedral structural units have a glass-forming function, but the octahedral ones have a modification function. From the electrochemistry point of view, the internal multiphase interfaces in such films are distributed multiphase electrodes. The adsorbed water together with defects of the oxide particles provide reagents for reversible coloration reactions in the film. The colour centres can be induced thermally (oxygen nonstoichiometry) or electrically (injected ions) or by radiation (photoinjected hydrogen). The electrochromism and related phenomenon of α-WO₃ films can be directly related to ion insertion/extraction processes controlled by external forces. Electronic Publication     

Amperometric determination of cyanides at the low ppb level by automated preconcentration based on gas diffusion coupled to sequential injection analysis

A simple, sensitive method for determining free cyanides is described. The assay is based on automated gas diffusion of the analyte using sequential injection analysis (SIA) coupled to amperometric detection on a silver working electrode. The effects of varying several parameters affecting the analytical procedure (including the flow rates of the donor and acceptor streams, the concentrations of the reagents and the sample volumes) were studied. The validity and quality of the method were also assessed, by examining its linearity, limits of detection and quantitation, precision, selectivity to potentially interfering substances. Its sensitivity can be enhanced by applying a simple preconcentration step, following which limits of detection were found to be 0.05-0.12 μg L⁻¹. Application of the proposed assay to the analysis of tap, mineral and table water samples spiked at concentrations ranging from 1 to 10 μg L⁻¹ CN⁻, yielded satisfactory recoveries (88-112%).     

The APCVD of tungsten oxide thin films from reaction of WCl6 with ethanol and results on their gas-sensing properties

The APCVD reaction of WCl₆ with ethanol was examined to deposit tungsten oxide on gas sensor substrates. Deposited films, which were WO_3−x, displayed a different morphology than those seen previously for CVD tungsten oxide. The gas-sensing properties of the deposited films were examined.     

Integration of electrochemical generator and detector of nitric oxide with the aid of the iron porphyrin

An electrochemical cell of generating nitric oxide (NO) was constructed in order to realize the catalytic reaction of nitrite by iron porphyrin [Y. Chi, J. Chen, K. Aoki, Inorg. Chem. 43 (2004) 8437]. The cell was composed of the generator of the iron porphyrin-including Nafion^®-coated electrode, the ion-exchange membrane, and the electrochemical detector of NO. The reduction of iron porphyrin in the presence of nitrite at the generator coordinates nitrite to form the NO-included complex, of which oxidation releases NO. The water-dissolved NO diffused to the detector through the membrane to block nitrite. It was detected by voltammetry with the aid of the oxidative catalytic reaction of iron porphyrin.     

An improved flow-injection system for spectrophotometric determination of molybdenum and tungsten in tool steels

A flow-injection procedure for simultaneous spectrophotometric determination of tungsten and molybdenum in steel alloys is proposed. The method exploits the catalytic effects of Mo(VI) and W(VI) on the rate of iodide oxidation by hydrogen peroxide under acidic conditions. A novel strategy for ion-exchange separation of the potential interfering species is proposed, and an AG50W-X8 cationic resin mini-column is used. The sample is injected twice, originating two sequential plugs, citrate being added to one of them in order to suppress the W(VI) catalytic activity thus providing the kinetic discrimination.The system handles 70 samples per hour and requires 1.6 mg KI per determination. A linear response is verified up to 10 mg l⁻¹ Mo (or W) in the injectate, and signal additivity is 98-103%. Results are precise (R.S.D. < 0.04) and in agreement with ICP-OES. Running a standard reference material (IPT-50) assessed also accuracy.     

Flow injection electrochemical hydride generation inductively coupled plasma time-of-flight mass spectrometry for the simultaneous determination of hydride forming elements and its application to the analysis of fresh water samples

A flow injection (FI) method was developed using electrochemical hydride generation (EcHG) as a sample introduction system, coupled to an inductively coupled plasma time-of-flight mass spectrometer (ICP-TOFMS) for rapid and simultaneous determination of six elements forming hydrides (As, Bi, Ge, Hg, Sb and Se). A novel low volume electrolysis cell, especially suited for FI experiments was designed and the conditions for simultaneous electrochemical hydride generation (EcHG; electrolyte concentrations and flow rates, electrolysis voltage and current) as well as the ICP-TOFMS operational parameters (carrier gas flow rate, modulation pulse width (MPW)) for the simultaneous determination of 12 isotopes were optimized. The compromise operation parameters of the electrolysis were found to be 1.4 and 3 ml min⁻¹ for the anolyte and catholyte flow rates, respectively, using 2 M sulphuric acid. An optimum electrolysis current of 0.7 A (16 V) and an argon carrier gas flow rate of 0.91 l min⁻¹ were chosen. A modulation pulse width of 5 μs, which influences the sensitivity through the amount of ions being collected by the MS per single analytical cycle, provided optimum results for the detection of transient signals. The achieved detection limits were compared with those obtained by using FI in combination with conventional nebulization (FI-ICP-TOFMS); values for chemical hydride generation (FI-CHG-ICP-TOFMS) were taken from the literature. By using a 200 μl sample loop absolute detection limits (3σ) in the range of 10-160 pg for As, Bi, Ge, Hg, Sb and 1.1 ng for Se and a precision of 4-8% for seven replicate injections of 20-100 ng ml⁻¹ multielemental sample solutions were achieved. The analysis of a standard reference material (SRM) 1643d (NIST, “Trace Elements in Water”) showed good agreement with the certified values for As and Sb. Se showed a drastic difference, which is probably due to the presence of hydride-inactive Se species in the sample. Recoveries better than 93% for Ge and Hg and 83.9% for Se were achieved on a spiked SRM sample. The developed method was successfully applied to the simultaneous multielemental determination of hydride forming elements in spring water samples originating from two different regions in Hungary.     

Development of a new electrochemical hydride generator with tungsten wire cathode for the determination of As and Sb by atomic fluorescence spectrometry

A novel electrochemical hydride generator has been developed for the determination of As and Sb. This newly devised hydride generator is constructed from a flowing electrolytic cell, in which the tungsten wire is selected as cathode. Compared with some cathode material usually used in electrochemical hydride generator, the tungsten cathode is of better interference tolerance, corrosion-resistant and longer working time. The characteristics of the cathode material, hydride generating efficiency and interferences of concomitant have been studied in detail. The detection limits (3σ) of As and Sb in sample solution were 0.10 μg L⁻¹ and 0.15 μg L⁻¹, the precisions for 11 replicate measurements of 20 μg L⁻¹ As and Sb were 1.3% and 1.7%. The electrochemical hydride generator coupled with atomic fluorescence spectrometry has been applied to the determination of total As and Sb in tobacco samples.     

On-line electrochemical preconcentration and flame atomic absorption spectrometric determination of manganese in urine samples

A sensitive and selective method was developed for the determination of traces of manganese in urine using on-line electrochemical preconcentration followed by flame atomic absorption spectrometry detection. A home made flow-through polypropylene cell (4.5 cm long × 0.8 cm diameter filled with glass marbles) with an effective inner volume of 0.5 ml containing a working and a counter electrode, both of glassy carbon and a Pt pseudo reference electrode was located in a flow injection manifold specially designed for the purpose of this work. The manganese was deposited from buffer solution of NH₃/NH₄Cl at pH 9.00 through an oxidizing process at a current of 400 mA during 7 min. A flow of HCl 0.1 mol l⁻¹ at 4 ml min⁻¹ through the cell, chemically dissolved the deposit. A small portion (15 μl) of the concentrate was introduced in a continuously flowing system by means of a timing device and was then carried to the detector for the manganese quantification. All electrochemical and spectroscopic variables as well as possible interferences in both systems were systematically studied. The relative standard deviations for ten consecutive measurements of manganese solutions of 2.0 and 20 μg l⁻¹ were of 2.3 and 1.5%, respectively, while for a sample processed five times was less then 5%. The accuracy of the developed procedure was evaluated by adding known amounts of manganese standard to urine samples and following the whole procedure. Recoveries within the range 97.2-102.8% were obtained. To further prove the accuracy, a Seronorm Trace Elements in Urine, Batch 403125 sample with a reported concentration of 13 μg Mn l⁻¹ was also analyzed. The experimental value obtained was of 12.7 ± 0.1 μg l⁻¹, which does not differ significantly from the reported amount (p < 0.05). A preconcentration factor of 40, a linear range between 0.015 and 60 μg l⁻¹ and a limit of detection of 15 ng l⁻¹ permitted the determination of manganese in real urine samples from non-exposed subjects in the range 0.5-2.8 μg l⁻¹.     

An amperometric sensor based on hemin adsorbed on silica gel modified with titanium oxide for electrocatalytic reduction and quantification of artemisinin

The present work describes the development of an amperometric sensor based on hemin immobilized on a titanium oxide modified silica toward detection of artemisinin (ARN) in neutral medium at an applied potential of −0.5 V vs. Ag/AgCl. The sensor presented its best performance in 0.1 mol L⁻¹ phosphate buffer solution, at pH 7.0. After optimizing the operational conditions, the sensor provided a linear response range for ARN reduction from 50 nmol L⁻¹ to 1000 nmol L⁻¹ with a sensitivity, detection and quantification limits of 24.66 A L mol⁻¹, 15 nmol L⁻¹ and 52 nmol L⁻¹, respectively. The proposed sensor showed a stable response for at least 80 successive determinations. The repeatability of the measurements with the sensor and the preparation of a series of electrodes, evaluated in terms of relative standard deviation, were 4.1% and 5.0%, respectively, for n = 10. The developed sensor was applied for the determination of ARN in the crude extracts of A. vulgaris L and the average recovery for these samples is 101.4 (± 3.1)%.     

Pareto-optimal front as a tool to study the behaviour of experimental factors in multi-response analytical procedures

This work presents a methodology to analyse the behaviour of an analytical procedure, above all when optimization of the procedure is needed. The methodology starts by the design of an experiment suitable to fit response surfaces to some analytical responses of interest in the problem being studied. Then, a pareto-optimal front is estimated that accounts for the optimal possibly trading-off solutions among the responses. The analysis of the behaviour of the optimal values of the response surfaces and the experimental conditions that provide these values allows going deeply into the analytical procedure.     

Evaluation of the antioxidant power of honey, propolis and royal jelly by amperometric flow injection analysis

In this paper is described the applicability of a flow injection system, operating with an amperometric detector, for measurement in rapid and simple way the antioxidant power of honey, propolis and royal jelly. The proposed method evaluates the reducing power of selected antioxidant compounds and does not require the use of free radicals or oxidants. Twelve honey, 12 propolis and 4 royal jelly samples of different botanical and geographical origin were evaluated by the electrochemical method and the data were compared with those obtained by the DPPH assay. Since a good correlation was found (R² = 0.92) the proposed electrochemical method can be successfully employed for the direct, rapid and simple monitoring of the antioxidant power of honeybee products. Furthermore, the total phenolic content of samples was determined by the Folin-Ciocalteau procedure and the characteristic antioxidant activities showed a good correlation with phenolics (R² = 0.96 for propolis and 0.90 for honey).     

A New Approach how to Define the Coefficient of Electroactivity of Adenine and Its Twelve Derivatives Using Flow Injection Analysis with Amperometric Detection

We studied the electrochemical behaviour of adenine derivates (adenosine, 2‐aminopurine, 2,6‐diaminopurine, 6‐benzyl‐aminopurine, adenosine monophosphate, cyclic adenosine monophosphate, nicotinamide adenine dinucleotide, adenosine triphosphate, S‐adenosyl‐L ‐methionine, and synthetic derivatives AD‐3, AD‐6 and AD‐9) using flow injection analysis with electrochemical detection using a glassy carbon electrode. The influences of pH, flow rate and potential on the signal height of the studied derivates were tested. The optimal pH was 3, the flow rate of the mobile phase 0.75 mL min^?1 and the potential 1100 mV. Further, we attempted to characterize each of the studied derivatives by mathematical equations and classic analytical parameters. The lowest detection limit was estimated for adenine as 0.9 nM and 2‐aminopurine as 0.5 nM.     

微透析取样-流动注射电化学检测测定表柔比星与牛血清白蛋白体外结合参数

建立了微透析取样-流动注射电化学检测法测定表柔比星与牛血清白蛋白体外结合参数的方法。流动相为pH 3.0的0.1 mol/L H3PO4-NaH2PO4缓冲液(含3.4×10﹣5mol/L Na2EDTA),流速为0.3 mL/min。电化学检测的工作电极为玻碳电极,工作电位为0.52V。表柔比星浓度在5.0×10-5～5.0×10-7 mol/L范围内与峰电流呈良好的线性关系,其相关系数为0.9997,检出限为2.0×10-7mol/L。结合微透析取样,实现了对表柔比星与牛血清白蛋白结合参数的测定。表柔比星与牛血清白蛋白的体外结合符合Scatchard曲线,结合常数和结合位点数分别为2.41×104L/mol和4.02。     

Use of nickel implanted boron-doped diamond thin film electrode coupled to HPLC system for the determination of tetracyclines

The electrochemical analysis of tetracyclines was investigated using nickel-implanted boron-doped diamond thin film electrode (Ni-DIA) by cyclic voltammetry and high performance liquid chromatographic with amperometry. Cyclic voltammetry was used to study the electrochemical oxidation of tetracyclines. Comparison experiments were carried out utilizing as-deposited BDD and glassy carbon electrodes. Ni-DIA electrode provided well-resolved oxidative irreversible cyclic voltammograms and the highest current signals among the electrode studied. High performance liquid chromatography (HPLC) with amperometric detection was also studied. The chromatography was performed using a commercially available Inertsil C18 column, with the mobile phase being: 80% phosphate buffer (pH 2.5)-20% acetonitrile and detected at 1.55 V. The methods were validated over the concentration range 0.05-100 ppm with the overall average recoveries from 83.3 to 102.5% and R.S.D. of less than 10%. The proposed method was further applied to analyse shrimp samples.     

Study on the chemiluminescence behavior of bovine serum albumin with luminol and its analytical application

In this paper, the luminescence behavior of bovine serum albumin (BSA) and luminol was first studied by flow injection chemiluminescence (CL). It was found that the hyperchromic effect of luminol in the presence of BSA led to the acceleration of the electrons transferring rate of excited 3-aminophthalate, which greatly enhanced the CL intensity of luminol/dissolved oxygen reaction. The increments of CL intensity were proportional to the concentrations of BSA with a linear range from 0.01 to 7 nmol L(-1). It was also found that azithromycin could inhibit the CL intensity of luminol/BSA reaction. The decrements of CL intensity were logarithm over the concentrations of azithromycin ranging from 0.1 to 700 ng mL(-1). At a flow rate of 2.0 mL min(-1), a complete analytical process, which included sampling and washing, could be performed within 30s with relative standard deviations of less than 3.1%. This proposed method was successfully applied in assaying azithromycin in pharmaceutical and human serum samples with recoveries from 91.0 to 104.3%. The possible luminescence mechanism of luminol/BSA/azithromycin reaction was discussed in detail by CL, UV and fluorescence methods.