Simultaneous determination of antioxidants at a chemically modified electrode with vitamin B12 by capillary zone electrophoresis coupled with amperometric detection

In the paper, a new kind of vitamin B₁₂ (acquo-cobalamine) chemically modified electrode was fabricated and applied in capillary zone electrophoresis coupled with amperometric detection (CZE-AD) for simultaneous determination of six antioxidants in fruits and vegetables. The catalytic electrochemical properties of the chemically modified electrode could obviously enhance oxidation peak heights responses by about five times to glutathione, ascorbic acid, vanillic acid, chlorogenic acid, salicylic acid, and caffeic acid compared with common carbon disk electrode. Furthermore, the effects of working electrode potential, pH and concentration of running buffer, separation voltage and injection time on CZE-AD were investigated. Under the optimum conditions, the six analytes could be completely separated and detected in a borate-phosphate buffer (pH 8.4) within 15 min. Their linear ranges were from 2.5 × 10⁻⁷ to 1.0 × 10⁻⁴ mol L⁻¹ and the detection limits were as low as 10⁻⁸ mol L⁻¹ magnitude (S/N = 3). The proposed method has been successfully employed to monitor the six analytes in practical samples with recoveries in the range 96.0-106.0% and RSDs less than 5.0%. Above results demonstrate that capillary zone electrophoresis coupled with electrochemical detection using vitamin B₁₂ modified electrode as detector is of convenient preparation, high sensitivity, good repeatability, and could be used in the rapid determination of practical samples.     

La3Ru8B6 and Y3Os8B6, new members of a homologous series R(A)nM3n−1B2n

Two new compounds, La₃Ru₈B₆ and Y₃Os₈B₆, were synthesized by arc melting the elements. Their structural characterization was carried out at room temperature on as-cast samples by using X-ray diffractometry. According to X-ray single-crystal diffraction results these borides crystallize in Fmmm space group (no. 69), Z=4, a=5.5607(1) Å, b=9.8035(3) Å, c=17.5524(4) Å, ρ=8.956 Mg/m³, μ=25.23 mm⁻¹ for La₃Ru₈B₆ and a=5.4792(2) Å, b=9.5139(4) Å, c=17.6972(8) Å, ρ=13.343 Mg/m³, μ=128.23 mm⁻¹ for Y₃Os₈B₆. The crystal structure of La₃Ru₈B₆ was confirmed from Rietveld refinement of X-ray powder diffraction data. Both La₃Ru₈B₆ and Y₃Os₈B₆ compounds are isotypic with the Ca₃Rh₈B₆ compound and their structures are built up from CeCo₃B₂-type and CeAl₂Ga₂-type structural fragments taken in ratio 2:1. They are the members of structural series R(A)_nM_3n−1B_2n with n=3 (R is the rare earth metal, A the alkaline earth metal, and M the transition metal). Structural and atomic parameters were also obtained for La_0.94Ru₃B₂ compound from Rietveld refinement (CeCo₃B₂-type structure, P6/mmm space group (no. 191), a=5.5835(9) Å, c=3.0278(6) Å).     

Capillary electrophoresis procedure for the simultaneous analysis and stoichiometry determination of a drug and its counter-ion by using dual-opposite end injection and contactless conductivity detection: Application to labetalol hydrochloride

In this work, a capillary electrophoresis (CE) procedure was developed for the simultaneous determination of a pharmaceutical drug and its counter-ion, namely labetalol hydrochloride. For this purpose, an uncoated fused-silica capillary, a low conductivity background electrolyte (BGE) and a capacitively coupled contactless conductivity detector (C⁴D) were employed. This detection system is highly sensitive and enables detection of inorganic as well as organic ions unlike with direct UV detection. Moreover, to be able to simultaneously analyze the cationic drug (labetalol⁺) and its anionic counter-ion (Cl⁻) in the same electrophoretic run without the need of a coated capillary, a dual-opposite end injection was performed. In this technique, the sample is hydrodynamically injected into both ends of the capillary. This method is simple and easy to perform since the different injection steps are automated by the CE software.This novel CE-C⁴D procedure with dual-opposite end injection has been successfully validated and applied for the analysis of chloride content in an adrenergic antagonist (labetalol hydrochloride). Thus, the hereby developed method has been shown to enable fast (analysis time < 10 min), precise (repeatability of migration times < 0.7% and of corrected-peak areas < 3.3%; n = 6) and rugged analyses for the simultaneous determination of a pharmaceutical drug and its counter-ion.     

K2B12F12: A rare A2X structure for an ionic compound at ambient conditions

The anhydrous salt K₂B₁₂F₁₂ crystallized from aqueous solution and its structure was determined by single crystal X-ray diffraction. The Ni₂In-type structure it exhibits is rare for an A₂X ionic compound at 25 °C and 1 atm., consisting of an expanded hexagonal close-packed array of B₁₂F₁₂²⁻ centroids (cent?cent distances: 7.204-8.236 Å) with half of the K⁺ ions filling all of the O_h holes and half of the K⁺ ions filling all of the D_3h trigonal holes in the close-packed layers that are midway between two “empty” T_d holes. The structure is also unusual in that the bond-valence sum for the K⁺ ions in O_h holes is less than or equal to 0.73 (the bond-valence sum for the other type of K⁺ ion is 1.16). A variation of the Ni₂In structure is exhibited by the previously published monohydrate Cs₂(H₂O)B₁₂F₁₂, for which an improved structure is also reported here. For K₂B₁₂F₁₂: monoclinic, C2/c, a = 8.2072(8), b = 14.2818(7), c = 11.3441(9) Å, β = 92.832(5)°, Z = 4, T = 120(2) K. For Cs₂(H₂O)B₁₂F₁₂: orthorhombic, P2₁2₁2₁, a = 9.7475(4), b = 10.2579(4), c = 15.0549(5) Å, Z = 4, T = 110(1) K.     

Thermochemistry of NaRb[B4O5(OH)4]·4H2O

The enthalpies of solution of NaRb[B₄O₅(OH)₄]·4H₂O in approximately 1 mol dm⁻³ aqueous hydrochloric acid and of RbCl in aqueous (hydrochloric acid + boric acid + sodium chloride) were determined. From these results and the enthalpy of solution of H₃BO₃ in approximately 1 mol dm⁻³ HCl(aq) and of sodium chloride in aqueous (hydrochloric acid + boric acid), the standard molar enthalpy of formation of −(5128.02 ± 1.94) kJ mol⁻¹ for NaRb[B₄O₅(OH)₄]·4H₂O was obtained from the standard molar enthalpies of formation of NaCl(s), RbCl(s), H₃BO₃(s) and H₂O(l). The standard molar entropy of formation of NaRb[B₄O₅(OH)₄]·4H₂O was calculated from the Gibbs free energy of formation of NaRb[B₄O₅(OH)₄]·4H₂O computed from a group contribution method.     

HPLC-ESI-MS analysis of Vitamin B12 in food products and in multivitamins-multimineral tablets

Methods for the determination of Vitamin B₁₂ remain limited due to their low sensitivity and poor selectivity. In the present work, a simple and sensitive HPLC-ESI-MS method for determining Vitamin B₁₂ in food products and in multivitamin-multimineral tablets was developed. Vitamin B₁₂ was extracted from food products with 50 mM sodium acetate buffer (pH 4.0) in the presence of sodium cyanide. Total Vitamin B₁₂ content in food product can be obtained by efficient enzymatic hydrolysis to release the bound Vitamin B₁₂. Vitamin B₁₂ was quantified with ginsenoside Re as internal standard (I.S.) after their separations on a C₁₈ column with a gradient of mobile phase made of water and acetonitrile. MS with SIR mode at m/z 930.8 was used for Vitamin B₁₂ quantification. The calibration graphs plotted with five concentrations of Vitamin B₁₂ was linear with a regression coefficient r² = 0.9994. The intra-assay R.S.D. and the inter-assay R.S.D. were 2.6% (n = 5) and 3.5% (n = 6), respectively. The recoveries evaluated at spiking three different concentrations on fortified products were above 93%. The method has been applied successfully in the determination of Vitamin B₁₂ in fortified food products and multivitamin-multimineral tablets.     

Simultaneous enzyme immunoassay for the screening of aflatoxin B1 and ochratoxin A in chili samples

Membrane-based immunoassay has been developed for simultaneous estimation of aflatoxin B₁ (AFB₁) and ochratoxin A (OA) in chili samples. The combined estimation of both the mycotoxins is more economical in respect of time, work and materials than two separate assays. The method uses a low cost test device consisting of a membrane with immobilized anti-AFB₁ and anti-OA antibodies and a filter paper attached to a polyethylene card below the membrane. It allows direct analysis of sample extracts containing substantial amount (40%) of methanol. This permits the use of two-fold diluted sample extracts resulting in minimum dilution error. The limit of quantitation obtained was 2 and 10 μg kg⁻¹ for AFB₁ and OA, respectively. The tolerance of 40% methanol was found to be due to the application of small size (0.8 mm diameter) spots on membranes, as the tolerance decreases to 20% with gradual increase in spot size. The combined method is capable of producing acceptable results to analyze AFB₁ and OA in chili with accuracy and precision. The AFB₁ and OA values obtained for spiked and naturally contaminated chili samples by the simultaneous method were in good correlation with those measured by individual ELISA. The method offers a simple, rapid and cost-effective screening tool to meet the requirements of the rapidly evolving EU legislation.     

Thermochemistry of dicesium calcium tetraborate octahydrate

The enthalpies of solution of Cs₂Ca[B₄O₅(OH)₄]₂·8H₂O(s) in approximately 1 mol dm⁻³ aqueous hydrochloric acid and of CsCl(s) in aqueous (hydrochloric acid + boric acid + calcium oxide) were determined. From these results and the enthalpies of solution of H₃BO₃(s) in approximately 1 mol dm⁻³ HCl(aq) and of CaO(s) in aqueous (hydrochloric acid + boric acid), the standard molar enthalpy of formation of −(10328 ± 6) kJ mol⁻¹ for Cs₂Ca[B₄O₅(OH)₄]₂·8H₂O(s) was obtained from the standard molar enthalpy of formation of CaO(s), CsCl(s), H₃BO₃(s) and H₂O(l). The standard molar entropy of formation of Cs₂Ca[B₄O₅(OH)₄]₂·8H₂O(s) was calculated from the thermodynamic relation with the standard molar Gibbs free energy of formation of Cs₂Ca[B₄O₅(OH)₄]₂·8H₂O(s) computed from a group contribution method.     

Iodination of cisplatin adduct of Vitamin B12 [{B12}-CN-{cis-PtCl(NH3)2}]

The cisplatin adduct of vitamin B₁₂, [{B₁₂}-CN-{cis-PtCl(NH₃)₂}]⁺ (1), reacts with iodide in aqueous solution to form [{B₁₂}-CN-{trans-PtI₂(NH₃)}] (3) in good yield. Mono-substitution of chloride was not observed since a subsequent replacement of one NH₃ by a second iodide is very fast as compared to the Cl⁻ → I⁻ exchange. The same reaction conditions allowed to introduce radioiodide ¹³¹I. Vitamin B₁₂ can therefore be labeled with radionuclides via binding to the Pt(II) center.     

Aflatoxin B1 and M1 in milk

The aflatoxin M₁ (AFLAM₁) is a mycotoxin that results from the hydroxylation of the aflatoxin B₁ (AFLAB₁). It contaminates the milk of animals fed with a diet containing its precursor. In this work, we determined the occurrence of AFLAB₁ and AFLAM₁ in milk, as well as the chromatographic conditions to quantify these mycotoxins. The extraction and quantification of AFLAB₁ and AFLAM₁ in naturally contaminated and artificially spiked milk samples which are produced and marketed in the state of RS were performed using the AOAC official method and UHPLC with fluorescence detection. We obtained a separation factor of 2.3 for AFLAB₁ and AFLAM₁ using a mobile phase consisting of 1% acetic acid:acetonitrile:methanol (55:10:35). The analytical curves had a wide linearity range and the limit of quantification (LOQ_m) concentrations of AFLAB₁ and AFLAM₁ were equal to 0.5 and 0.25 μg L⁻¹, respectively. Samples of pasteurized and ultra-high-temperature processed (UHT) milk showed natural contamination, and the levels for both aflatoxins ranged from 0.7 to 1.5 μg L⁻¹. Raw and concentrated milk samples only contained AFLAM₁, with a maximum average concentration of 1.7 μg L⁻¹. These concentrations, higher than permitted by legislation, confirm the existence of a health risk, as well as highlight the relevance of searching for alternatives to reduce this contamination.     

A sensitive and highly stable electrochemical impedance immunosensor based on the formation of silica gel-ionic liquid biocompatible film on the glassy carbon electrode for the determination of aflatoxin B1 in bee pollen

The paper describes a sensitive and highly stable label-free electrochemical impedance immunosensor for the determination of aflatoxin B₁ (AFB₁), which is based on the formation of silica gel-ionic liquid biocompatible film on the glassy carbon electrode. The electrochemical performances of the sensor were investigated by electrochemical impedance spectroscopy using a Fe(CN)₆^3−/4− phosphate buffer solution as base solution for test. As new ionic liquid, 1-amyl-2,3-dimethylimidazolium hexafluorophosphate, offers a very biocompatible microenvironment for AFB₁ antibody, the sensor exhibits good repeatability (RSD = 1.2%), sensitive electrochemical impedance response to AFB₁ in the range of 0.1-10 ng ml⁻¹ and lowers the detection limit of AFB₁ (0.01 ng ml⁻¹)_. The electron-transfer resistance change of the sensor after and before incubation with AFB₁ of 2.0 ng ml⁻¹ can retain 95% over a 180-day storage period at 4 °C. The results present a remarkable improvement of sensitivity (2-fold) and long-term stability (190-fold) when compared to classical silica gel sensor. Moreover, proposed sensor has a high selectivity to AFB₁ alone with no significant response to AFB₂, AFG₁, AFG₂ and AFM₁ as single substrates, it has been successfully applied to the determination of trace AFB₁ in bee pollen samples with a spiked recovery in the range of 96.0-102.5%.     

Sub-picogram determination of Vitamin B12 in pharmaceuticals and human serum using flow injection with chemiluminescence detection

A sensitive chemiluminescence (CL) method, based on the enhancive effect of cobalt(II) on the CL reaction between luminol and dissolved oxygen in a flow injection (FI) system, was proposed for determination of Vitamin B₁₂. The increment of the CL intensity was proportional to the concentration of Vitamin B₁₂, giving a calibration graph linear over the concentration from 2.0×10⁻¹⁰ to 1.2×10⁻⁶ g l⁻¹ (r²=0.9992) with the detection limit of 5.0×10⁻¹¹ g l⁻¹ (3σ). At a flow rate of 2.0 ml min⁻¹, a complete determination of Vitamin B₁₂, including sampling and washing, could be accomplished in 0.5 min with the relative standard deviations (R.S.D.) of less than 5.0%. The proposed method was applied successfully to the determination of Vitamin B₁₂ in pharmaceuticals, human serum, egg yolk and fish tissue.     

The non-centrosymmetric borate oxides, MBi2B2O7 (M=Ca, Sr)

Two novel noncentrosymmetric borates oxides, MBi₂B₂O₇ or MBi₂O(BO₃)₂ (MCa, Sr), have been synthesized by solid-state reactions in air at temperatures in the 600-700 °C range. Their crystal structures have been determined ab initio and refined using powder neutron diffraction data. CaBi₂B₂O₇ crystallizes in the orthorhombic Pna2₁ space group with a=8.9371(5) Å, b=5.4771(3) Å, c=12.5912(7) Å, Z=4, R_wp=0.118, χ²=2.30. SrBi₂B₂O₇ crystallizes in the hexagonal P6₃ space group with a=9.1404(4) Å, c=13.0808(6) Å, Z=6, R_wp=0.115, χ²=4.15. Large displacement parameters suggest the presence of disorder in SrBi₂B₂O₇ as also revealed by diffuse 2×a superstructure reflections in electron diffraction patterns. Both structures are built of identical (001) neutral layers of corner-sharing BO₃ triangles and MO₆ trigonal prisms forming six-membered rings in which Bi₂O groups are located. Adjacent layers are stacked in a staggered configuration and connected through weak Bi-O bonds. A moderate efficiency for second harmonic generation (SHG) has been measured for a powder sample of CaBi₂B₂O₇ (d_eff=2d_eff(KDP)).     

The study of Bi3B5O12: synthesis, crystal structure and thermal expansion of oxoborate Bi3B5O12

The paper presents a new data on the crystal structure, thermal expansion and IR spectra of Bi₃B₅O₁₂. The Bi₃B₅O₁₂ single crystals were grown from the melt of the same stoichiometry by Czochralski technique. The crystal structure of Bi₃B₅O₁₂ was refined in anisotropic approximation using single-crystal X-ray diffraction data. It is orthorhombic, Pnma, a=6.530(4), b=7.726(5), c=18.578(5) Å, V=937.2(5) Å³, Z=4, R=3.45%. Bi³⁺ atoms have irregular coordination polyhedra, Bi(1)O₆ (d(B-O)=2.09-2.75 Å) and Bi(2)O₇ (d(B-O)=2.108-2.804 Å). Taking into account the shortest bonds only, these polyhedra are considered here as trigonal Bi(1)O₃ (2.09-2.20 Å) and tetragonal Bi(2)O₄ (2.108-2.331 Å) irregular pyramids with Bi atoms in the tops of both pyramids. The BiO₄ polyhedra form zigzag chains along b-axis. These chains alternate with isolated anions [B₂^IVB₃^IIIO₁₁]⁷⁻ through the common oxygen atoms to form thick layers extended in ab plane. A perfect cleavage of the compound corresponds to these layers and an imperfect one is parallel to the Bi-O chains. The Bi₃B₅O₁₂ thermal expansion is sharply anisotropic (α₁₁≈α₂₂=12, α₃₃=3×10⁻⁶ °C⁻¹) likely due to a straightening of the flexible zigzag chains along b-axis and decreasing of their zigzag along c-axis. Thus the properties like cleavage and thermal expansion correlate to these chains.     

Crystal-chemistry of mullite-type aluminoborates Al18B4O33 and Al5BO9: A stoichiometry puzzle

Orthorhombic Al₂O₃-rich aluminoborate is an important ceramic material for which two slightly different compositions have been assumed: Al₅BO₉ (5Al₂O₃:B₂O₃) and Al₁₈B₄O₃₃ (9Al₂O₃:2B₂O₃). The formula Al₁₈B₄O₃₃ (=Al_4.91B_1.09O₉) was derived from results of chemical analyses when crystal structure data were not yet available. Subsequent structural investigations indicated Al₅BO₉ composition. Nevertheless, Al₁₈B₄O₃₃ was still accepted as the correct stoichiometry assuming that additional B replaces 9% Al.Powder samples of both compositions and ones with excess boron were prepared by solid state reactions between α-Al₂O₃ and B₂O₃/H₃BO₃ at temperatures above 1100 °C and single-crystals were grown from flux at 1100 and 1550 °C. Products were investigated by single-crystal and powder XRD, ¹¹B and ²⁷Al solid-state MAS-NMR, Raman and FTIR spectroscopy as well as Laser-ablation ICP-MS. No indication of the predicted 9% B→Al substitution was found. LA ICP-MS indicated 12.36(27) wt% B₂O₃ corresponding to Al_4.97B_1.03O₉. Hence, the suggested Al₁₈B₄O₃₃ stoichiometry can be excluded for all synthesized samples. A very low amount of Al vacancies at a five-fold coordinated site are likely, charge balanced by an additional nearby three-fold coordinated B site. All evidences indicate that the title compound should be reported as Al_5−xB_1+xO₉ with x<0.038(6), which is close to Al₅BO₉.     

Synthesis and thermochemistry of MgO·3B2O3·3.5H2O

A new magnesium borate MgO·3B₂O₃·3.5H₂O has been synthesized by the method of phase transformation of double salt and characterized by XRD, IR and Raman spectroscopy as well as by TG. The structural formula of this compound was Mg[B₆O₉(OH)₂]·2.5H₂O. The enthalpy of solution of MgO·3B₂O₃·3.5H₂O in approximately 1 mol dm⁻³ HCl was determined. With the incorporation of the standard molar enthalpies of formation of MgO(s), H₃BO₃(s), and H₂O(l), the standard molar enthalpy of formation of −(5595.02±4.85) kJ mol⁻¹ of MgO·3B₂O₃3.5H₂O was obtained. Thermodynamic properties of this compound was also calculated by group contribution method.     

Hydrothermal synthesis, characterization and thermochemistry of Ca2[B2O4(OH)2]·0.5H2O

A pure calcium borate Ca₂[B₂O₄(OH)₂]·0.5H₂O has been synthesized under hydrothermal condition and characterized by XRD, FT-IR and TG as well as by chemical analysis. The molar enthalpy of solution of Ca₂[B₂O₄(OH)₂]·0.5H₂O in HC1·54.582H₂O was determined. From a combination of this result with measured enthalpies of solution of H₃BO₃ in HC1·54.561H₂O and of CaO in (HCl + H₃BO₃) solution, together with the standard molar enthalpies of formation of CaO(s), H₃BO₃(s) and H₂O(l), the standard molar enthalpy of formation of −(3172.5 ± 2.5) kJ mol⁻¹ of Ca₂[B₂O₄(OH)₂]·0.5H₂O was obtained.     

Use of vitamin B2 for fluorescence detection of thymidine-related single-nucleotide polymorphisms

In combination with abasic site (AP site)-containing DNAs, potential use of a biotic fluorescence compound, Vitamin B₂ (riboflavin), is demonstrated for the fluorescence detection of the thymine (T)-related single-nucleotide polymorphisms. Our method is based on construction of the AP site in DNA duplexes, which allows small ligands to bind to target nucleotides accompanied by fluorescence signaling: an AP site-containing probe DNA is hybridized with a target DNA so as to place the AP site toward a target nucleobase, by which hydrophobic microenvironments are provided for ligands to recognize target nucleotides through stacking and hydrogen-bonding interactions. In 10 mM sodium cacodylate buffer solutions (pH 7.0) containing 100 mM NaCl and 1.0 mM EDTA, Vitamin B₂ is found to selectively bind to T (K₁₁ = 1.8 × 10⁶ M⁻¹ at 5 °C) over other nucleobases, and this is accompanied by significant quenching of its fluorescence. While the sensing functions depend on the flanking sequences to the AP site, Vitamin B₂ is applicable to the detection of T/C (cytosine), T/G (guanine) and T/A (adenine) mutation sequences of the CYP2A6 gene, where the flanking nucleobases are guanines in both positions (-GXG-, X = AP site).     

Simultaneous capillary electrophoretic determination of Sc(III) and Y(III) based on the complex-formation with a lacunary Keggin-type [PW11O39] complex

Trace amounts of Sc(III) and Y(III) can react with [PW₁₁O₃₉]⁷⁻ to form the ternary Keggin-type complexes: [P(Sc^IIIW₁₁)O₄₀]⁶⁻ and [P(Y^IIIW₁₁)O₄₀]⁶⁻ having high molar absorptivities in the UV region. Since the rate of the complex-formation was very rapid and the kinetically stable ternary anions migrated in the capillary with different electrophoretic mobilities, the complex-formation reaction was applied to the simultaneous CE determination of Sc(III) and Y(III) with direct UV detection at 250 nm. For both Sc(III) and Y(III), the pre-column method provided linear calibration curves in the range of 2 × 10⁻⁷ to 1 × 10⁻⁵ M; the respective detection limits were 1 × 10⁻⁷ M (the signal-to-noise ratio = 3). The proposed method was successfully applied to the determination of Sc(III) and Y(III) in river water.     

Synthesis and crystal structure of four Pd(II) complexes containing nido or closo carborane diphosphine ligands

Three Pd(II) complexes [Pd₂(μ-Cl)₂{7,8-(PPh₂)₂-7,8-C₂B₉H₁₀}₂] · 0.25CH₂Cl₂ (1), [Pd{7,8-(PPh₂)₂-7,8-C₂B₉H₁₀}₂] · 4CHCl₃ (2) and [PdCl₂(1,2-(PPh₂)₂-1,2-C₂B₁₀H₁₀)] (3) have been synthesized by the reactions of 1,2-(PPh₂)₂-1,2-C₂B₁₀H₁₀ with PdCl₂ in acetonitrile, cyanophenyl and dichloromethane, respectively. A fourth complex, [PdI₂(1,2-(PPh₂)₂-1,2-C₂B₁₀H₁₀)] (4), was obtained by a ligand exchange reaction through the substitution of the Cl⁻ of complex 3 with I⁻. All four complexes have been characterized by elemental analysis, FT-IR, ¹H and ¹³C NMR spectroscopy and X-ray structure determination. Single crystal X-ray determination showed that the carborane cage, nido for 1, 2 and closo for 3, 4, was coordinated bidentately to the Pd atom through the two P atoms, and the geometry at the Pd atom was square-planar in all the complexes.