A novel cloud point extraction approach using cationic surfactant for the separation and pre-concentration of chromium species in natural water prior to ICP-DRC-MS determination

A novel cloud point phase separation of cationic surfactant, Aliquat-336 and capabilities of its reactive solubilizing sites for selective extraction of chromium species at ultra trace levels was examined in natural water. The phase separation behavior of Aliquat-336 is studied with various additives. The nonionic surfactant, Triton X-114 was found to induce the cloud point phase separation of Aliquat-336. The separation of anionic Cr(VI) was enabled by the formation of ion associate with quaternary ammonium head group of Aliquat-336 at pH 2, and the recovery of Cr(VI) and Cr(III) were 101.4 ± 1.4% and 2.2 ± 0.4%, respectively at 0.5-1 ng mL⁻¹, Total Cr was pre-concentrated as Cr-APDC species using the hydrophobic tail group at pH 6.5. The Cr(III) concentration was obtained by subtracting Cr(VI) from total Cr. The recovery of total Cr was 99.5 ± 1.2%. Parameters affecting extraction were assessed. The procedure was applied to NIST 1643c and NIST 1643d waters, and the sum of individual species obtained was compared with the certified chromium values. The method was also applied to various natural waters with limits of detection and pre-concentration factor of 0.010 and 0.025 ng mL⁻¹; 10 and 10, respectively, for Cr(VI) and Cr(III)-APDC using ICP-MS operated in DRC mode.     

Flame atomic absorption determination of manganese(II) in natural water after cloud point extraction

The possibility to use 4-(2-pyridylazo)resorcinol (PAR) and 1-(2-pyridylazo)-2-naphthol (PAN) for manganese(II) concentrating by the micellar extraction at cloud point (CP) temperature and subsequent atomic absorption spectrometry (AAS) determination was investigated. Under the optimum conditions, preconcentration of 100 ml of water sample in the presence of 1% non-ionic surfactant (NS) OP-7, 1×10⁻⁴ M 1-(2-pyridylazo)-2-naphthol permitted the detection 5 μg l⁻¹ manganese. The proposed method has been applied to the AAS determination of manganese in water samples after cloud point extraction.     

Spectrophtometric determination of malachite green in fish farming water samples after cloud point extraction using nonionic surfactant Triton X-100

A novel and sensitive cloud point extraction procedure for the determination of trace amounts of malachite green by spectrophotometry was developed. Malachite green was extracted at pH 2.5 mediated by micelles of nonionic surfactant Triton X-100. The extracted surfactant-rich phase was diluted with ethanol and its absorbance was measured at 630 nm. The effect of different variables such as pH, Triton X-100 concentration, cloud point temperature and time and diverse ions was investigated and optimum conditions were established. The calibration graph was linear in the range of 4-500 ng mL⁻¹ of malachite green in the initial solution with r = 0.9996 (n = 10). Detection limit based on three times the standard deviation of the blank (3S_b) was 1.2 ng mL⁻¹ and the relative standard deviation (R.S.D.) for 20 and 300 ng mL⁻¹ of malachite green was 1.48 and 1.13% (n = 8), respectively. The method was applied to the determination of malachite green in different fish farming and river water samples.     

Micelle-mediated cloud point extraction and spectrophotometric determination of rhodamine B using Triton X-100

A new micelle-mediated cloud point extraction method is described for sensitive and selective determination of trace amounts of rhodamine B by spectrophotometry. The method is based on the cloud point extraction of rhodamine B from aqueous solution using Triton X-100 in acidic media. The extracted surfactant rich phase is diluted with water and its absorbance is measured at 563 nm by a spectophotometer. The effects of different operating parameters such as concentration of surfactant and salt, temperature and pH on the cloud point extraction of rhodamine B were studied in details and a set of optimum conditions were obtained. Under optimum conditions a linear calibration graph in the range of 5-550 ng mL⁻¹ of rhodamine B in the initial solution with r = 0.9991 (n = 15) was obtained. Detection limit based on three times the standard deviation of the blank (3S_b) was 1.3 ng mL⁻¹ (n = 10) and the relative standard deviation (R.S.D.) for 50 and 350 ng mL⁻¹ of rhodamine B was 2.40 and 0.87% (n = 10), respectively. The method was applied for the determination of rhodamine B in soft pastel, hand washing liquid soap, matches tip and textile dyes mixture samples.     

Determination of thermodynamic parameters for cloud point extraction of Arsenazo-III and Magdala Red dyes using mixed micelles: An essential requirement for high performance

A simple and low cost method for extraction and preconcentration of Arsenazo-III (ARS-III) and Magdala Red (MR) was developed by an efficient cloud point extraction (CPE) method using mixed micelles of Triton X–114 (TX–114) and cetyltrimethyl ammonium bromide (CTAB). Various parameters, such as pH/concentration of H₂SO₄, surfactant concentrations (TX-114 and CTAB), equilibrium temperature and time have been studied to maximise efficiency. Thermodynamic quantities like change in Gibbs free energy (ΔG⁰), change in enthalpy (ΔH⁰) and change in entropy (ΔS⁰) were calculated. The results show that the CPE of ARS-III and MR dye is feasible, spontaneous, and endothermic in the temperature range of (50–80) °C indicating good recoveries for the developed method. The effect of temperature, surfactant concentration and dye concentration on various thermodynamic quantities was investigated and it was found that ΔG⁰ values increased with temperature but decreased with surfactant and dye concentration. ΔH⁰ and ΔS⁰ values increased as surfactant concentration increased and decreased as dye concentration decreased. The recoveries were found to be the range from 90.02 – 101.03 % for ARS-III and 86.07–99.46 % for MR dyes which proves that the method is highly efficient.     

Determination of Prometryne in water and soil by HPLC-UV using cloud-point extraction

A CPE-HPLC (UV) method has been developed for the determination of Prometryne. In this method, non-ionic surfactant Triton X-114 was first used to extract and pre-concentrate Prometryne from water and soil samples. The separation and determination of Prometryne were then carried out in an HPLC-UV system with isocratic elution using a detector set at 254 nm wavelength. The parameters and variables that affected the extraction were also investigated and the optimal conditions were found to be 0.5% of Triton X-114 (w/v), 3% of NaCl (w/v) and heat-assisted at 50 °C for 30 min. Using these conditions, the recovery rates of Prometryne ranged from 92.84% to 99.23% in water and 85.48% to 93.67% in soil, respectively, with all the relative standard deviations less than 3.05%. Limit of detection (LOD) and limit of quantification (LOQ) were 3.5 μg L⁻¹ and 11.0 μg L⁻¹ in water and 4.0 μg kg⁻¹ and 13.0 μg kg⁻¹ in soil, respectively. Thus, we developed a method that has proven to be an efficient, green, rapid and inexpensive approach for extraction and determination of Prometryne from soil samples.     

Determination of mercury in biological samples by cold vapor atomic absorption spectrometry following cloud point extraction with salt-induced phase separation

Method development for the pre-concentration of mercury in human hair, dogfish liver and dogfish muscle samples using cloud-point extraction and cold vapor atomic absorption spectrometry is demonstrated. Before the extraction, the samples were submitted to microwave-assisted digestion in a mixture of H₂O₂ and HNO₃. Cloud point extraction was carried out using 0.5% (m/v) ammonium O,O-diethyldithiophosphate (DDTP) as the chelating agent and 0.3% (m/v) Triton X-114 as the non-ionic surfactant. Phase separation was induced after the addition of Na₂SO₄ to a final concentration of 0.2 mol L⁻¹. Aliquots of the final extract were transferred to PTFE tubes and NaBH₄ and HCl were added. The mercury vapor was driven to a non-heated quartz tube for measuring the absorbance. The results obtained with salt-induced phase separation were in good agreement with the certified values at a 95% confidence level. An enrichment factor of 10 allowed a detection limit of 0.4 ng g⁻¹ to be obtained, which demonstrates the high sensitivity of the proposed procedure for the determination of mercury at trace levels.     

Development of a cloud point extraction and preconcentration method for silver prior to flame atomic absorption spectrometry

The possibility was investigated of using 2-mercaptobenzothiazole (MBT) for Ag(I) concentration by micellar extraction at cloud point (CP) temperature and subsequent determination by flame atomic absorption spectrometry (FAAS). The method is based on the complexation of Ag(I) with 2-mercaptobenzothiazole (MBT) in the presence of non-ionic micelles of Triton X-114. The effect of experimental conditions such as pH, concentration of chelating agent and surfactant, equilibration temperature and time on cloud point extraction was studied. Under the optimum conditions, the preconcentration of 10 mL of water sample in the presence of 0.1% Triton X-114 and 2 × 10⁻⁴ mol L⁻¹ 2-mercaptobenzothiazole permitted the detection of 2.2 ng mL⁻¹ silver. The calibration graph was linear in the range of 10–200 ng mL⁻¹, and the recovery of more than 99% was achieved. The proposed method was used in FAAS determination of Ag(I) in water samples.     

Flow method based on cloud point extraction for fluorometric determination of epinephrine in human urine

A novel stepwise injection fluorometric method for the determination of epinephrine in human urine has been developed. In the current study, the stepwise injection analysis (SWIA) was successfully combined with on-line in-syringe cloud point extraction (CPE) and fluorometric detection. The procedure was based on the epinephrine derivatization in the presence of o-phenylenediamine followed by the preconcentration stage based on the CPE with the nonionic surfactant Triton X-114. After the phase separation into a syringe of the flow system, the micellar phase containing the epinephrine derivative was transported to a fluorometric detector. The excitation and emission wavelengths were set at 447 nm and 550 nm, respectively. The conditions of epinephrine derivatization and CPE have been studied. The calibration plot constructed using the developed procedure was linear in the range of 1·10⁻¹¹–5·10⁻⁷ mol L⁻¹. The limit of detection, calculated as 3 σ of a blank test (n = 10), was found to be 3·10⁻¹² mol L⁻¹. The proposed method was successfully applied for the determination of epinephrine in human urine samples.     

On-line metals preconcentration and simultaneous determination using cloud point extraction and inductively coupled plasma optical emission spectrometry in water samples

A new on-line cloud point extraction (CPE) system coupled to ICP-OES was designed for simultaneous extraction, preconcentration and determination of Cd²⁺, Co²⁺, Cr³⁺, Cu²⁺, Fe³⁺ and Mn²⁺ ions in water samples. This is based on the complexation of the metal ions with 1-(2-thenoyl)-3,3,3-trifluoraceton reagent (TTA) at pH 6.0 in the presence of non-ionic surfactant of Triton X-114. The micellar solution was heated above 60 °C and loaded through a column packed with cotton, which acts as a filter for retaining the analyte-entrapped surfactant-rich phase. Then the surfactant-rich phase was eluted using propanol:0.5 mol L⁻¹ nitric acid solution (75:25, v/v) at a flow rate of 3.0 mL min⁻¹ and directly introduced into the nebulizer of the ICP-OES. Several factors influencing the instrumental conditions and extraction were evaluated and optimized. Under the optimum conditions, the enhancement factors of the proposed method for target ions were between 42 and 97, the detection limits (DLs) were in the range of 0.1-2.2 μg L⁻¹. The relative standard deviations (R.S.D.s) at 100 μg L⁻¹ concentration levels of each ion were found to be less than 4.6%. Also, the calibration graphs were linear in the range of 0.5-100 μg L⁻¹ with the correlation coefficients within the range of 0.9948-0.9994.Finally, the developed method was successfully applied to the extraction and determination of the mentioned metal ions in the tap, well, sea and mineral water samples and satisfactory results were obtained.     

Cloud point extraction procedure for flame atomic absorption spectrometric determination of lead(II) in sediment and water samples

The conditions for cloud point extraction of lead(II) from aqueous solutions were investigated and optimized. The procedure is based on the separation of Pb(II) – brillant cresyl blue (BCB) complexes into the micellar media by adding the surfactant Triton X-114. After phase separation, the surfactant-rich phase was dissolved with 1 mol L⁻¹ HNO₃ in ethanol and diluted with 1 mol L⁻¹ HNO₃ solution before lead was determined by flame atomic absorption spectrometry. Optimization of the pH, ligand and surfactant quantities, incubation time, temperature, viscosity, sample volume, and interfering ions was performed. The effects of the matrix ions were also examined. The detection limits for three times the standard deviations of the blank for lead were 7.5 μg L⁻¹ for water samples and 0.33 μg g⁻¹ for sediment samples. The validity of cloud point extraction was checked by employing certified reference samples of Lake Sediment IAEA-SL-1 and Sewage Sludge BCR-CRM 144R. The procedure was applied to natural waters and sediment samples with satisfactory results (recoveries >95%, relative standard deviations <6.4%).     

Thermodynamics of non-ionic surfactant Triton X-100-cationic surfactants mixtures at the cloud point

This study investigates the effects of gemini and conventional cationic surfactants on the cloud point (CP) of the non-ionic surfactant Triton X-100 (TX-100) in aqueous solutions. Instead of visual observation, a spectrophotometer was used for measurement of the cloud point temperatures. The thermodynamic parameters of these mixtures were calculated at different cationic surfactant concentrations. The gemini surfactants of the alkanediyl-α-ω-bis (alkyldimethylammonium) dibromide type, on the one hand, with different alkyl groups containing m carbon atoms and an ethanediyl spacer, referred to as “m-2-m” (m = 10, 12, and 16) and, on the other hand, with –C₁₆ alkyl groups and different spacers containing s carbon atoms, referred to as “16-s-16” (s = 6 and 10) were synthesized, purified and characterized. Additions of the cationic surfactants to the TX-100 solution increased the cloud point temperature of the TX-100 solution. It was accepted that the solubility of non-ionic surfactant containing polyoxyethylene (POE) hydrophilic chain was a maximum at the cloud point so that the thermodynamic parameters were calculated at this temperature. The results showed that the standard Gibbs free energy , the enthalpy and the entropy of the clouding phenomenon were found positive in all cases. The standard free energy increased with increasing hydrophobic alkyl chain for both gemini and conventional cationic surfactants; however, it decreased with increasing surfactant concentration.     

浊点萃取-火焰原子吸收光谱法测定催化剂中痕量钯的研究

研究了以1-（2-吡啶偶氮）-2-萘酚（PAN）为络合剂,以非离子型表面活性刺Triton X-100为萃取剂的浊点萃取分离富集-火焰原子吸收光谱法测定痕量钯的新方法。详细考察了溶液的pH、络合剂和表面活性剂浓度、平衡温度和时间等条件对浊点萃取效果的影响。该方法对钯的检出限为30．8ng／mL,相对标准偏差（RSD）为2．1％（n=10）,回收率在97．8％-106．6％之间。可用于催化剂中Pd（Ⅱ）的测定。     

Simultaneous cloud point extraction and spectrophotometric determination of carmoisine and brilliant blue FCF in food samples

A novel simultaneous cloud point extraction method for the determination of carmoisine and brilliant blue FCF by spectrophotometry has been developed. The method is based on the cloud point extraction of carmoisine and brilliant blue FCF from aqueous solution using Triton X-100, diluting the extracted surfactant rich phase with water and measuring the absorbance at 522 and 640 nm for carmoisine and brilliant blue FCF, respectively. The effects of different parameters such as pH, concentration of surfactant and temperature on the cloud point extraction of both dyes were investigated and optimum conditions were established. Linear calibration curves were obtained in the range of 0.02-3.50 μg mL⁻¹ for carmoisine and 0.05-3.50 μg mL⁻¹ for brilliant blue FCF under optimum conditions. Detection limit based on three times the standard deviation of the blank (3S_b) was 0.017 and 0.016 μg mL⁻¹ (n = 10) for carmoisine and brilliant blue FCF, respectively. The relative standard deviation (RSD) for 0.1 μg mL⁻¹ was 4.14 and 3.30% (n = 10), for carmoisine and brilliant blue FCF, respectively. The method was applied to the simultaneous determination of the dyes in different food samples.     

Selective extraction and preconcentration of cerium(IV) in water samples by cloud point extraction and determination by inductively coupled plasma optical emission spectrometry

Cloud point extraction (CPE) was used for the selective extraction and separation of cerium(IV) from aqueous solutions. The method is based on the formation of cerium(IV)-n-p-tolylbenzohydroxamic acid (n-TBHA) complex that is extracted into the micellar phase (Triton X-114) at a temperature above the cloud point temperature (CPT). After phase separation, the surfactant rich phase was diluted up to 1.0 mL and determined by inductively coupled plasma-optical emission spectrometry (ICP-OES). Under the optimum extraction conditions and instrument parameters, by preconcentration of only 10.0 mL of sample in the presence of 0.09% Triton X-114, an enhancement factor of 13.8 was obtained. The analytical curve was linear in the range of 1.5–1200 μg L⁻¹ and the detection limit was 0.4 μg L⁻¹. The method was applied to the determination of Ce(IV) in water samples with satisfactory results.     

Separation and preconcentration of trace amounts of aluminum ions in surface water samples using different analytical techniques

A separation/preconcentration of aluminum (III) (Al³⁺) has been developed to overcome the problem of high matrix species, which may interfere with the determination of trace quantity of Al³⁺ in natural water samples. The separation of Al³⁺ in water samples was carried out from interfering cations by complexing them with 2-methyle 8-hyroxyquinoline (quinaldine) on activated silica. Whereas the separated trace amounts of Al³⁺ was preconcentrated by cloud point extraction (CPE), as prior step to its determination by spectrofluorimetry (SPF) and flame atomic absorption spectrometry (FAAS). The Al³⁺ react with 8-hydroxyquinoline (oxine) and then entrapped in non-ionic surfactant Triton X-114. The main factors affecting CPE efficiency, such as pH of sample solution, concentration of oxine and Triton X-114, equilibration temperature and time period for shaking were investigated in detail. The validity of separation/preconcentration of Al³⁺ was checked by certified reference material of water (SRM-1643e). After optimization of the complexation and extraction conditions, a preconcentration factor of 20 was obtained for Al³⁺ in 10 mL of natural water samples. The relative standard deviation for 6 replicates containing 100 μg L⁻¹ of Al³⁺ was 5.41 and 4.53% for SPF and FAAS, respectively. The proposed method has been applied for determination of trace amount of Al³⁺ in natural water samples with satisfactory results.     

Determination of trace vanadium in soil by cloud point extraction and graphite furnace atomic absorption spectroscopy

This work describes a new analytical procedure for trace vanadium by graphite furnace atomic absorption spectroscopy coupled to cloud point extraction (CPE) as the separation-preconcentration method. The CPE behavior of vanadium using methylene blue as complex agent and Triton X-100 as a surfactant was investigated systematically. Under the optimized conditions, the detection limit was 0.7 ng · mL⁻¹, and the relative standard deviation was 4.3% for vanadium (c = 50.0 ng · mL⁻¹, n = 5). The recovery of vanadium was in the range of 98.9–102.8%. The method was applied to the analysis of vanadium in certified reference materials and real samples. The results obtained were in good agreement with the certified values. Correspondence: Xiashi Zhu, Key Laboratory of Environmental Material and Environmental Engineering of Jiangsu province/College of Chemistry and Chemical Engineering, Yangzhou University, Yangzhou 225002, P.R. China     

Selective cloud point extraction and preconcentration of trace amounts of silver as a dithizone complex prior to flame atomic absorption spectrometric determination

Dithizone (diphenylthiocarbazone) was used as a complexing agent in cloud point extraction for the first time and applied for selective preconcentration of trace amounts of silver. The analyte in the initial aqueous solution was acidified with sulfuric acid (pH<1) and Triton X-114 was added as a surfactant. After phase separation, based on the cloud point separation of the mixture, the surfactant rich phase was diluted with tetrahydrofuran (THF) and the analyte determined in the enriched solution by flame atomic absorption spectrometry. After optimization of the complexation and extraction conditions, a preconcentration factor of 43 was obtained for only 10 ml of sample. The analytical curve was linear in the range of 3-200 ng ml⁻¹ and the limit of detection was 0.56 ng ml⁻¹. The proposed method was applied to the determination of silver in water samples.     

Determination of lead in water samples by graphite furnace atomic absorption spectrometry after cloud point extraction

Cloud point extraction (CPE) has been used for the pre-concentration of lead, after the formation of a complex with 2-(5-bromo-2-pyridylazo)-5-(diethylamino)-phenol (5-Br-PADAP), and later analysis by graphite furnace atomic absorption spectrometry (GFAAS) using octylphenoxypolyethoxyethanol (TritonX-114) as surfactant. The chemical variables affecting the separation phase were optimized. Separation of the two phases was accomplished by centrifugation for 15 min at 4000 rpm. Under the optimum conditions i.e., pH 8.0, cloud point temperature 40 °C, [5-Br-PADAP] = 2.5 × 10⁻⁵ mol l⁻¹, [Triton X-114] = 0.05%, added methanol volume = 0.15 ml, pre-concentration of only 10 ml sample permitted an enhancement factor of 50-fold. The lower limit of detection (LOD) obtained under the optimal conditions was 0.08 μg l⁻¹. The precision for 10 replicate determinations at 5 μg l⁻¹ Pb was 2.8% relative standard deviation (R.S.D.). The calibration graph using the pre-concentration system for lead was linear with a correlation coefficient of 0.9984 at levels near the detection limits up to at least 30 μg l⁻¹. The method was successfully applied to the determination of lead in water samples.     

The cloud point extraction of copper(II) with monocarboxylic acids into non-ionic surfactant phase

The possibility to use monocarboxylic acids and their mixtures with amines for copper concentrating by the way of micellar extraction at cloud point temperature, and later atomic absorption spectrometry (AAS) determination was investigated. Under the optimum conditions, preconcentration of 100 ml of water sample in the presence of 1% non-ionic surfactant OP-10, 0.005 M capric acid and 0.01 M octylamine permitted the detection of 0.01 μg ml⁻¹ copper. The proposed method has been applied to the AAS determination of copper in water samples after cloud point extraction.