A method based on precolumn derivatization and ultra high performance liquid chromatography with high‐resolution mass spectrometry for the simultaneous determination of phthalimide and phthalic acid in tea

Phthalimide can be formed from either the degradation of folpet and phosmet, or reaction of phthalic anhydride with primary amino groups. Consequently, the sum of phthalimide and folpet, expressed as folpet‐residue definition, is highly prone to false‐positive levels of folpet in tea. An analytical method is thus urgently needed to investigate the residue level and source of phthalimide in tea. In this work, we developed an accurate method of determining phthalimide and phthalic acid (the indicator of phthalic anhydride) by acetonitrile extraction and 3‐bromopropyltrimethylammonium bromide derivatization coupled with ultra high performance liquid chromatography and high‐resolution mass spectrometry. The method was validated, and linearity (correlation coefficients > 0.99) was obtained. Satisfactory recoveries at 10, 20, 50, and 100 μg/kg ranged from 76 to 117%, and the intra‐ and interday accuracies were <23%. The limit of quantification for phthalimide and phthalic acid was 10 μg/kg. The developed method was further successfully used to determine phthalimide and phthalic acid in some tea samples. The positive rate of phthalimide and phthalic acid detected in the tea samples ranged from 30–75 and 50–90%, respectively.     

Thermo-oxidative processes in biodegradable poly(butylene succinate)

Aliphatic polyesters have acquired significant interest as environmentally friendly thermoplastics for a wide range of applications, and understanding their degradation behaviour has relevance both for processing and end uses. We have investigated the thermal and thermo-oxidative degradation processes occurring in synthetic and commercial poly(butylene succinate) (PBSu). Thermal oxidation was performed in atmospheric air using extremely thin polymer films at 170 °C for up to 6 h. The oxidized compounds were analyzed by size exclusion chromatography (SEC), NMR spectroscopy, and Mass Spectrometry (MALDI-TOF MS). A measurable reduction of the molar mass of the polyesters was soon apparent, promoting the formation of PBSu oligomers with different end groups. MALDI mass spectrometry combined with the use of extremely thin polyester films provided a virtual magnifying glass to obtain exhaustive information on the structure of the oxidation products. An α-H abstraction mechanism has been unambiguously ascertained to be the primary step in PBSu oxidation. The oxidized polymer chains originating from the decomposition of the hydroperoxide intermediate by radical rearrangement reactions had not been revealed before. The latter products subsequently undergo chain scission processes, which can be accurately traced from the chemical species identified in our work. Thermal degradation experiments were also performed under nitrogen at 240-260 °C. The new species identified in the MALDI spectra support a decomposition pathway taking place through a β-hydrogen-transfer mechanism, followed by the production of succinic anhydride from succinic acid end molecules via a back-biting process.     

Thalidomide analogs from diamines: Synthesis and evaluation as inhibitors of TNF-alpha production

Fourteen thalidomide analogs bearing two phthalimido units were prepared in high yields (83-94%) by condensation of different diamines with phthalic or 3-nitrophthalic anhydride. An in vitro investigation of the compounds as inhibitors of the TNF-alpha production was performed. The inhibition was higher for compounds bearing amino and nitro groups and was modulated by increasing the size of the spacers between the phthalimide groups.     

An example of quality control of fine chemical intermediates: related impurity analysis of industrial phthalic anhydride by reversed-phase high-performance liquid chromatography

A reliable reversed-phase high-performance liquid chromatographic method has been developed for analysis of related impurities in industrial phthalic anhydride (PA). Maleic acid (hydrolysis product of maleic anhydride), phthalimide, and benzoic acid were separated from phthalic acid (Pa, hydrolysis product of PA) on a C₁₈ column by gradient elution with acetonitrile and 0.1% (v/v) aqueous perchloric acid solution. This method is simple, sensitive, and accurate, and has been successfully applied to quality control of PA for industrial use.     

N-取代邻苯二甲酰亚胺类衍生物的设计、合成及活性评价

结合中药脱皮马勃中分离得到的3,5-二羟基邻苯二甲酰亚胺和邻苯二甲酰亚胺类化合物的结构设计合成了一系列N-取代-3,5-二甲氧基邻苯二甲酰亚胺及N-取代-3,5-二羟基邻苯二甲酰亚胺类衍生物,其结构经¹H NMR,¹³C NMR和MS分析确证. 选取人肺腺癌细胞A549及人脐静脉血管内皮细胞HUEVC为测试细胞株,评价了所合成化合物的体外抗肿瘤及抗血管生成活性,结果表明,部分化合物表现出一定的活性.     

Combined techniques for the characterization of linear–hyperbranched hybrid poly(butylene adipate) copolymers

Linear–hyperbranched hybrid poly(butylene adipate) (HPBA) copolymers were synthesized through a branching reaction between the linear tailored prepolymer terminated with methyl ester groups and different mol percents of the 1,1,1‐tris(hydroxymethyl) propane (TMP) as branching agent, using the titanium(IV) isopropoxide as catalyst, at 180 °C under vacuum for different times. All samples were characterized by NMR and matrix assisted laser desorption/ionization time of flight mass spectrometry (MALDI‐TOF MS). In particular, MALDI‐TOF mass spectra of the unfractionated and size exclusion chromatography (SEC)‐fractionated hyperbranched (HB) samples gave information on their composition, on the end groups as well as on the TMP units present in each family of HB macromolecules. HB chains containing cyclic branches and ether bonds formed by intermolecular transesterification and intramolecular and intermolecular transetherification side reactions, respectively, were also revealed by MALDI‐TOF MS analysis. All samples were also investigated by SEC. The average molar masses (MMs) evaluated by SEC calibrated with the polystyrene (PS) narrow standards were overestimated with respect to those calculated by the SEC/MALDI‐TOF MS self‐ calibration method, which gave reliable values. Moreover, it also showed that the hydrodynamic volume of the HPBA polymers was higher than that of the linear PSs with similar MMs. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Thermal Oxidation Products of Nylon 6 Determined by MALDI‐TOF Mass Spectrometry

Matrix‐assisted laser desorption ionisation (MALDI) mass spectrometry was used, in an attempt to find firm evidence for the structure of the species produced in the thermal oxidative degradation of Nylon 6 (Ny6), at 250°C in air. The MALDI spectra of the products showed the presence of polymer chains containing aldehydes, amides, methyl and N‐formamide terminal groups. The aldehydes undergo further oxidation to produce carboxylic end groups. The formation of azomethines, from the further reaction of aldehydes with amino‐terminated Ny6 chains, is also supported by the appearance of specific peaks in the MALDI spectra.     

Lowering the dielectric constant of polyimide thin films by swelling with supercritical carbon dioxide

The swelling with supercritical carbon dioxide (sc‐CO₂) of thin films of polyimides having various structures was investigated. It was shown that the degree of swelling is significantly influenced by the solvent which was used for the synthesis of those polyimides, by the solvent which was used for the preparation of thin films and by the conformational rigidity of the polymers. The presence of hexafluoroisopropylidene groups in the main chain of a polymer prevents its swelling with sc‐CO₂. The best results were obtained for polyimide film ULTEM, based on m‐phenylene‐diamine and isopropylidene‐diphenoxy‐bis(phthalic anhydride), synthesized in benzoic acid, whose free volume increased twice and its dielectric constant decreased from 3.15 to 2.45 by swelling with sc‐CO₂. Copyright © 2013 John Wiley & Sons, Ltd.     

Solid-phase synthesis of thalidomide and its analogues

A novel solid-phase synthesis of thalidomide and its metabolites and analogues is described. The synthetic strategy involves the coupling of hydroxymethyl polystyrene with phthalic anhydride to form the resin-linked acid. The acid is then reacted with primary amines followed by acid or base treatment to form thalidomide and its analogues with either open or closed phthalimide rings. Most of the analogues are synthesized with high yields (40.3-98.1% in three steps) and purities (92.3-98.9%).     

Amine/anhydride reaction versus amide/anhydride reaction in polyamide/anhydride carriers

Polyamide 6 (PA6) and poly(metaxylene adipamide) (PAmXD6) were blended in a batch mixer with anhydrides such as phthalic anhydride, n-octadecyl succinic anhydride, and anhydride-grafted ethylene propylene rubber. The melt viscosity, the solution viscosity, and chain end concentration were studied during the mixing. PA was first mixed 5 min to get an homogeneous melt prior to the anhydride addition. The introduction of the anhydride to the molten polyamide resulted in large decreases of melt and solution viscosities and of amine chain end concentrations. The anhydride units react with amine chain ends to form imide groups. The resulting low amine chain end concentration causes hydrolysis reaction to maintain the condensation equilibrium. As a consequence an increased carboxylic chain end concentration is observed. The imide concentration was studied by IR. It was shown that when most of the amine chain ends are consumed, the remaining anhydride reacts with amino groups formed by polyamide hydrolysis. © 1995 John Wiley & Sons, Inc.     

Synthesis and polymerization of N-(ethylene)-phthalimidyl acrylate

N-(Ethylene)phthalimidyl acrylate was synthesized starting from phthalimide or phthalic anhydride using two different routes. Free radical or anionic polymerization of the ester resulted in low-molecular-weight polymers.     

Recent Advances in MALDI Mass Spectrometry of Polymers

Matrix-Assisted Laser Desorption/Ionization (MALDI) allows the identification of repeat units and end groups, the structural analysis of linear and cyclic oligomers, and the estimate of composition and sequence for copolymers. MALDI has also been applied to the measurement of molar mass distributions in polymers and to the study of thermal and oxidative processes in polymers. This paper illustrates the detection of self-association in macromolecules made by coupling MALDI and Size Exclusion Chromatography (SEC), the investigation of polymer oxidation phenomena, and the characterization of copolymers formed in the processing of reactive polymer blends.     

Polycondensations of hydroxycarboxylic acids derived from optically active aminoalcohols and acid anhydrides—syntheses of functional poly(ester-amide)s

Syntheses and polycondensations of optically active hydroxycarboxylic acids prepared from acid anhydrides and aminoalcohols were carried out. Novel polymers with M̄_n 9900–27,200 were obtained by the polycondensations of hydroxycaboxylic acids derived from maleic or succinic acid using 1.2 eq. of 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide hydrochloride (EDC · HCl) in DMF (2M) at room temperature for 8 h in satisfactory yields. Meanwhile, a hydroxycarboxylic acid obtained from phthalic acid afforded no polymer but a phthalimide derivative. The radical additions of ethanethiol or mercaptoethanol with the polymers derived from maleic anhydride proceeded smoothly in satisfactory incorporation ratios (65–98%), respectively. The polymer obtained from succinic anhydride and 2-aminoethanol showed hydrolytic degradability. © 1997 John Wiley & Sons, Inc.     

Pyrolysis studies on polyalkylene phthalates

The synthesis and identification of pyrolysis products of five polyalkylene phthalates are reported. The pyrolysis products are separated in a capillary gas chromatograph and the products are identified using a mass selective detector. The major degradation products for the polyesters now investigated are phthalic anhydride and the appropriate diol. In nearly all the polyesters studied, cyclic ether from the diol and the cyclic diester formed from phthalic anhydride and the diol are detected. A wide variety of low molecular weight compounds and considerable quantities of complex mono- and diesters of phthalic acid are identified among the pyrolysis products. The mode of formation of the products identified by GC/MS analysis are discussed with reference to the general polyester degradation mechanism.     

Synthesis and characterization of 2,2‐bis(methylol)propionic acid dendrimers with different cores and terminal groups

Three sets of aliphatic polyester dendrimers based on 2,2‐bis(methylol)propionic acid (bis‐MPA) were synthesized. Two of the sets had benzylidene terminal groups and either a trimethylolpropane or triphenolic core moiety. The last set had acetonide terminal groups and a triphenolic core moiety. Benzylidene‐[G#1]‐anhydride and acetonide‐[G#1]‐anhydride were used as the reactive building blocks in the construction of all dendrimers. The large excess of building blocks used in the coupling reactions initially resulted in considerable material loss. This waste was eliminated through the development of a recycling method. ¹H and ¹³C NMR and matrix‐assisted laser desorption/ionization time‐of‐flight (MALDI‐TOF) analysis were used to verify the purity of all compounds. Size exclusion chromatography (SEC) was used, as well as MALDI‐TOF, for molecular weight determinations. The SEC measurements were conducted with a universal calibration method and an online right‐angle laser light scattering detector. Measured dendrimer molecular weights were close to their theoretical molar masses. Observations were also made of the hydrodynamic radius and intrinsic viscosity for the different dendrimers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1758–1767, 2004     

Synthesis and radical polymerization of end-methacrylated poly(succinimide) leading to poly(aspartic acid) hydrogel

The polycondensation of aspartic acid in the presence of phthalic anhydride was carried out in mesitylene/sulfolane using o-phosphoric acid as a catalyst. The polymer yields were 91–78%, when 5–20 mol-% phthalic anhydride was added into the feed. The obtained poly(succinimide) carried a phthalic imide unit and a succinic acid unit as end groups. In the MALDI-TOF mass spectrum, the peak-to-peak distances between adjacent signals were 97.07 m/z, corresponding to the calculated value (97.07) of the succinimide unit. Poly(succinimide) was reacted with 2-(methacryloxy)ethyl isocyanate to give end-methacrylated poly-(succinimide), in which the end-functionality of the methacrylate group was ca. 1. End-methacrylated poly-(succinimide) was polymerized with ethylene glycol dimethacrylate using 2,2′-azoisobutyronitrile to give poly(succinimide) gel, which could be converted into water-absorbing poly(aspartic acid) hydrogel.     

2-(2-甲氧基苯氧)乙胺的新合成法

甲氧基苯氧乙胺;2-(2-甲氧基苯氧)乙胺的新合成法     

Synthesis,characterization and biological activity evaluation of new 3- methyl and 4- fluoro isoindoline-1, 3-dione/phthalimide analogues

The convenient route for the synthesis of a series of new Isoindoline-1, 3-dione/phthalimide analogues by condensation of substituted phthalic anhydride with an appropriate Ar-amine is described. Selective phthalimide derivatives were evaluated for their preliminary biological activities against Gram-positive, Gram-negative and fungi strains. These encouraging results could be helpful for the development of new antibacterial or antifungal agents.     

Photo-oxidation and ozonization of poly(3-hexylthiophene) thin films as studied by UV/VIS and photoelectron spectroscopy

The kinetics and the mechanisms of degradation of thin P3HT layers have been investigated quantitatively for ozonization and photo-oxidation. Both, decay kinetics and product evolution of the polymer degradation are monitored by in situ UV/VIS and X-ray photoelectron spectroscopy (XPS). The degradation pathways of ozonization and photo-oxidation of P3HT turn out to be significantly different. Ozone attacks the thiophene units mainly by direct addition to the double bonds, leading to the loss of UV/VIS absorption, while the aliphatic side chains [1] are hardly affected. During photo-oxidation, the polymer is primarily attacked at the alkyl side chain which leads to the formation of reactive peroxide species. These subsequently cause the oxidation of sulfur and concomitantly the destruction of the thiophene ring, resulting in the loss of absorption. From the kinetics of the blue shift of the optical absorption it is concluded that the polymer is mainly attacked at the terminal thiophene rings the case of photo-oxidation whereas ozone attacks positions more or less randomly distributed along the chain. The rate of photo-oxidation under AM 1.5 conditions is at least one order of magnitude faster than the decomposition of P3HT by ozone.     

SENSITIZED PHOTO-OXIDATION OF WOOL AND SILK BY A TRIAZINYLSTILBENE

Abstract— The photo-oxidation of wool and silk treated with a fluorescent brightening agent (a triazinylstilbene) has been studied. Complete amino acid analyses of the irradiated keratins showed that in the presence of this sensitizer, only tryptophyl and histidyl residues were susceptible to photodecomposition; the former were oxidized at a faster rate than the latter. Sixty per cent of the tryptophyl residues in silk were photo-oxidized during a 4 hr exposure to an artificial light source designed to simulate summer sunlight conditions. The rate of discoloration of the irradiated silk fabric, measured spectrophotometrically, was found to parallel closely the rate of photo-oxidation of the tryptophyl residues in the fabric.