ICP-MS with hexapole collision cell for isotope ratio measurements of Ca, Fe, and Se

To avoid mass interferences on analyte ions caused by argon ions and argon molecular ions via reactions with collision gases, an rf hexapole filled with helium and hydrogen has been used in inductively coupled plasma mass spectrometry (ICP-MS), and its performance has been studied. Up to tenfold improvement in sensitivity was observed for heavy elements (m > 100 u), because of better ion transmission through the hexapole ion guide. A reduction of argon ions Ar+ and the molecular ions of argon ArX+ (X = O, Ar) by up to three orders of magnitude was achieved in a hexapole collision cell of an ICP-MS ("Platform ICP", Micromass, Manchester, UK) as a result of gas-phase reactions with hydrogen when the hexapole bias (HB) was set to 0 V; at an HB of 1.6 V argon, and argon-based ions of masses 40 u, 56 u, and 80 u, were reduced by approximately four, two, and five orders of magnitude, respectively. The signal-to-noise ratio 80Se/ 40Ar2+ was improved by more than five orders of magnitude under optimized experimental conditions. Dependence of mass discrimination on collision-cell properties was studied in the mass range 10 u (boron) to 238 u (uranium). Isotopic analysis of the elements affected by mass-spectrometric interference, Ca, Fe, and Se, was performed using a Meinhard nebulizer and an ultrasonic nebulizer (USN). The measured isotope ratios were comparable with tabulated values from IUPAC. Precision of 0.26%, 0.19%, and 0.12%, respectively, and accuracy of 0.13% 0.25%, and 0.92%, respectively, was achieved for isotope ratios 44Ca/ 40Ca and 56Fe/57Fe in 10 microg L(-1) solution nebulized by means of a USN and for 78Se/80Se in 100 microg L(-1) solution nebulized by means of a Meinhard nebulizer.     

电感耦合等离子体质谱法测定水中低浓度铁受钙干扰的消除

采用电感耦合等离子体质谱法测定水中小于0.06 mg·L-1铁量时受到共存的钙(40mg·L-1)的严重干扰。经验证,钙的干扰可借以下途径消除:①采用碰撞池和56Fe、57Fe两同位素中的任一种,钙的干扰均可忽略不计。②如采用非碰撞池,则钙的干扰将因铁与其共存钙的质量浓度的不同而变化:(a)当cFe<0.10mg·L-1,cCa<1mg·L-1,并采用57Fe同位素时,钙的干扰可以忽略;(b)当cFe<0.10mg·L-1,cCa>1mg·L-1时,采用两同位素中的任一种都无法克服钙的严重干扰;(c)当cFe>0.10mg·L-1,cCa<5mg·L-1,无论采用同位素56Fe或57Fe,钙的干扰都不明显,而如cCa>5mg·L-1时,则只能用同位素56Fe才可避免钙的干扰。     

Isotopic analysis of Fe in human red blood cells by multiple collector-ICP-mass spectrometry.

Precise 56Fe/54Fe and 57Fe/54Fe isotopic ratios on human red blood cell (RBC) samples have been measured using multiple collector-ICP-mass spectrometry (MC-ICPMS). The mass spectrometric interferences on Fe isotopes (e.g., 56ArO+ and 57ArOH+) were successfully minimized by a dry plasma condition achieved by a desolvating nebulizer sample-introduction technique. In order to eliminate possible variations in the measured isotopic ratios due to non-mass spectrometric interferences, Fe was separated from remaining organic compounds and major co-existing elements using an ion chromatographic technique. The resulting precisions of the 56Fe/54Fe and 57Fe/54Fe ratio measurements were 0.12 per thousand and 0.20 per thousand, respectively, which were high enough to detect the isotopic variation of Fe in nature. For an interlaboratory comparison, all of the Fe isotopic ratio data were normalized by the ratios for the IRMM-014 international isotopic standard. A series of 12 RBC samples were collected from one person through monthly-based sampling over a period of one year. These were analyzed to test possible seasonal changes in the 56Fe/54Fe and 57Fe/54Fe ratios. Moreover, in order to test possible variations in the 56Fe/54Fe and 57Fe/54Fe ratios among different people, RBC samples were collected from five volunteers (four males and one female). The 56Fe/54Fe and 57Fe/54Fe ratios for a series of 12 RBC samples collected over a one-year period show 3.06 per thousand and 4.51 per thousand lower than the values of IRMM-014, and no significant seasonal change could be found in the ratios. The lack in seasonal changes in the Fe isotopic ratios could be explained by a small contribution of the daily net-intake of Fe (1 - 2 mg/day) onto the total amount of Fe in the human body (2 - 4 g). The 56Fe/54Fe and 57Fe/54Fe ratios for RBC samples collected from four male samples did not vary measurably, whereas the Fe isotopic ratios for a female RBC were 0.3 per thousand/amu heavier than the mean value of four male samples. This difference in Fe isotopes among the individuals can be the result of a difference in uptake efficiency of the Fe through a dietary process from the digestive tract. The data obtained here demonstrate that the isotopic ratios of trace metals can provide new information about metabolic efficiencies of the metallic elements.     

Absolute measurements and certified reference material for iron isotopes using multiple-collector inductively coupled mass spectrometry

Two enriched isotopes, 99.94 at.% 56Fe and 99.90 at.% 54Fe, were blended under gravimetric control to prepare ten synthetic isotope samples whose 56Fe isotope abundances ranged from 95% to 20%. For multiple-collector inductively coupled plasma mass spectrometry (MC-ICP-MS) measurements typical polyatomic interferences were removed by using Ar and H2 as collision gas and operating the MC-ICP-MS system in soft mode. Thus high-precision measurements of the Fe isotope abundance ratios were accomplished. Based on the measurement of the synthetic isotope abundance ratios by MC-ICP-MS, the correction factor for mass discrimination was calculated and the results were in agreement with results from IRMM014. The precision of all ten correction factors was 0.044%, indicating a good linearity of the MC-ICP-MS method for different isotope abundance ratio values. An isotopic reference material was certified under the same conditions as the instrument was calibrated. The uncertainties of ten correction factors K were calculated and the final extended uncertainties of the isotopic certified Fe reference material were 5.8363(37) at.% 54Fe, 91.7621(51) at.% 56Fe, 2.1219(23) at.% 57Fe, and 0.2797(32) at.% 58Fe.     

Photoionization study of L-valine in the gas phase by vacuum ultraviolet synchrotron radiation

The photoionization and photodissociation of L-valine are studied by tunable synchrotron vacuum ultraviolet photoionization mass spectrometry at the photon energy of 13 eV. The ionization energy of L-valine and the appearance energies of major fragments are measured by the photoionization efficiency spectrum in the photon energy range of 8-11 eV. Possible formation pathways of the major fragments, NH(2)CHC(OH)(2)(+) (m/z=75), NH(2)(CH(3))(2)(CH)(2)(+) (m/z=72) and NH(2)CHCO(+) (m/z=57), are discussed in detail with the theoretical calculations at the B3LYP/6-31++G (d, p) level. Hydrogen migration is considered as the key way for the formation of NH(2)CHC(OH)(2)(+) (m/z=75) and NH(2)CHCO(+) (m/z=57). Furthermore, other fragments, NH(2)CHCOOH(+) (m/z=74), (CH(3))(2)(CH)(2)(+) (m/z=56), C(4)H(7)(+) (m/z=55), NH(2)CHOH(+) (m/z=46), NH(2)CH(2)(+) (m/z=30) and m/z=18, species are also briefly described.     

Optimisation and critical evaluation of a collision cell technology ICP-MS system for the determination of arsenic in foodstuffs of animal origin

The determination of arsenic (⁷⁵As) was studied using an ICP-MS equipped with collision cell technology (CCT). Different mixtures of gases (He and H₂) were tested using HCl conditions and a He flow rate of 4 mL min⁻¹ was found to be suitable for the removal of the poly-atomic spectral interference [⁴⁰Ar³⁵Cl]⁺. Trueness of the optimised method has been evaluated in both standard and CCT modes on six certified reference materials in foodstuffs of animal origin and on three external proficiency testing schemes (FAPAS). The results obtained generally coincided with the certified values, except for CCT mode in some categories of samples (meat, mussels and milk powder), for which a positive bias on results was observed due to the formation of poly-atomic interferences within the collision cell. The main interferences were studied and their contributions estimated. [⁵⁸Fe¹⁶O¹H]⁺ and [⁷⁴Ge¹H]⁺ were the most significant interferences formed in the cell. Finally, different parameters (e.g. hexapole and quadrupole bias voltage, nebuliser gas flow) were optimised to try to attenuate these interferences.     

Determination of trace levels of iron in a seawater sample using isotope dilution/inductively coupled plasma mass spectrometry.

An analytical method for trace levels of iron in a seawater sample using isotope dilution ICP-MS was developed. Preconcentration of iron and the removal of major elements in seawater such as alkali and alkaline-earth elements can be carried out quickly using a chelating resin disk by adjusting the sample pH to 3. The collision cell option of the ICP-MS instrument method was used to improve the performance of the instrument for iron measurements since ArO and ArN interferences could be reduced using this analytical method. About 4 ml min(-1) helium, as the collision gas, were introduced into the cell. 40Ar14N and 40Ar16O which interfere with 54Fe and 56Fe in water had their amounts decreased by 5 orders of magnitude. Then, the isotope dilution method was used for iron determination below ng g(-1) level of trace iron in four environmental reference materials (river water standard sample JAC-0031 (Japan Soc. for Analytical Chemistry), estuarine standard sample SLEW-2 (NRC Canada) and seawater standard samples CASS-3 and NASS-5 (NRC Canada)) were measured. Good agreement between analytical results and certified values of reference materials was obtained, which confirmed the effectiveness of this method.     

Analysis of phosphorus herbicides by ion-pairing reversed-phase liquid chromatography coupled to inductively coupled plasma mass spectrometry with octapole reaction cell

A reversed phase ion-pairing high performance liquid chromatographic (RPIP-HPLC) method is developed for the separation of two phosphorus herbicides, Glufosinate and Glyphosate as well as Aminomethylphosphonic acid (AMPA), the major metabolite of Glyphosate. Tetrabutylammonium hydroxide is used as the ion-pairing reagent in conjunction with an ammonium acetate/acetic acid buffering system at pH 4.7. An inductively coupled plasma mass spectrometer (ICP-MS) is coupled to the chromatographic system to detect the herbicides at m/z = 31P. Historically, phosphorus has been recognized as one of the elements difficult to analyze in argon plasma. This is due to its relatively high ionization potential (10.5 eV) as well as the inherent presence of the polyatomic interferences 14N16O1H+ and 15N16O+ overlapping its only isotope at m/z = 31. An octapole reaction cell is utilized to minimize the isobaric polyatomic interferences and to obtain the highest signal-to-background ratio. Detection limits were found to be in the low ppt range (25-32 ng/l). The developed method is successfully applied to the analysis of water samples collected from the Ohio River and spiked with a standard compounds at a level of 20 microg/l.     

Determination of chromium, iron and selenium in foodstuffs of animal origin by collision cell technology, inductively coupled plasma mass spectrometry (ICP-MS), after closed vessel microwave digestion

The determination of chromium (⁵²Cr), iron (⁵⁶Fe) and selenium (⁸⁰Se) isotopes in foodstuffs of animal origin has been performed by collision cell technology (CCT) mode using an inductively coupled plasma mass spectrometry (ICP-MS) as detector after closed vessel microwave digestion. To significantly decrease the argon-based interferences at mass to charge ratios (m/z): 52 (⁴⁰Ar¹²C), 56 (⁴⁰Ar¹⁶O) and 80 (⁴⁰Ar⁴⁰Ar), the gas-flow rates of a helium and hydrogen mixture used in the hexapole collision cell were optimised to 1.5 ml min⁻¹ H₂ and 0.5 ml min⁻¹ He and the quadrupole bias was adjusted daily between −2 and −15 mV. Limits of quantification (LOQ) of 0.025, 0.086 and 0.041 mg kg⁻¹ for Cr, Fe and Se, respectively, in 6% HNO₃ were estimated under optimized CCT conditions. These LOQ were improved by a factor of approximately 10 for each element compared to standard mode.Precision under repeatability, intermediate precision reproducibility and trueness have been tested on nine different certified reference materials in foodstuffs of animal origin and on an external proficiency testing scheme. The results obtained for chromium, iron and selenium were in all cases in good agreement with the certified values and trueness was improved, compared to those obtained in standard mode.     

Determination of copper in coal fly ash in the presence of excess titanium by dynamic reaction cell inductively coupled plasma mass spectrometry

Inductively coupled plasma quadrupole mass spectrometry (ICP-QMS) was used for the accurate determination of copper in coal fly ash samples in the presence of excess titanium, using the reaction of Cu(+) ions with NH(3) in the cell. The method eliminated the effect of polyatomic isobaric interferences at m/z 63 and 65 caused by the formation of (47)Ti(16)O(+), (49)Ti(16)O(+) and (47)Ti(18)O(+) on (63)Cu(+) and (65)Cu(+) by detecting Cu(+) as the product cluster ion Cu(NH(3))(2)(+). As the signal of (63)Cu(NH(3))(2)(+) overlapped with that of (97)Mo(+) which existed in the samples, (65)Cu(NH(3))(2)(+) was detected at m/z 99. The effect of the operating conditions of DRC system was studied in order to obtain the best signal to noise ratio for Cu(NH(3))(2)(+) at m/z 99. The formation of Cu(NH(3))(2)(+) was through the clustering reaction Cu(+)+2NH(3)-->Cu(NH(3))(2)(+) which resulted in the separation of analyte from the interfering oxide. The detection limit for Cu(NH(3))(2)(+) was 0.015 ng mL(-1) as Cu. The method was applied to the determination of copper in NIST SRM 1633a and 1633b coal fly ash reference materials. The precision between sample replicates was better than 2.0% and the analysis results were in good agreement with the certified values.     

Gas-phase reactions between thiourea and Ca2+: new evidence for the formation of [Ca(NH3)]2+ and other doubly charged species.

The gas-phase reactions between Ca(2+) and thiourea are investigated by means of electrospray ionization/mass spectrometry experiments. The MS/MS spectra of [Ca(thiourea)](2+) complexes show the appearance of new doubly charged species formed by the loss of NH(3) and HNCS. Other intense peaks at m/z 43, 56, 60, 73, 76 and 98 are also observed, and assigned to monocations produced in different coulomb-explosion processes. The structures and bonding characteristics of the different stationary points of the [Ca(thiourea)](2+) potential energy surface (PES) were theoretically studied by DFT calculations carried out at B3LYP/cc-pWCVTZ level. The analysis of the topology of this PES permits to propose different mechanisms for the loss of ammonia and HNCS, and to identify, the m/z 43, 56, 60, 73, 76 and 98 peaks as H(2)NCNH(+), CaNH(2) (+), H(2)NCS(+), CaSH(+), thiourea(+) and CaNCS(+) ions respectively. There are significant dissimilarities between the reactivity of urea and thiourea, which are related to the lower ionization energy of the latter, and to the fact that thioenols are intrinsically more stable than enols with respect to the corresponding keto forms.     

Sensitive sulphur-specific detection of omeprazole metabolites in rat urine by high-performance liquid chromatography/inductively coupled plasma mass spectrometry

The use of high-performance liquid chromatography/inductively coupled plasma mass spectrometry (HPLC/ICPMS) with sulphur-specific detection was investigated as a method for obtaining metabolite profiles for the drug omeprazole administered as a 1:1 mixture of (32)S- and (34)S-labelled material. Analysis based on the monitoring of the chromatographic eluent at either m/z 32 or 34 was not successful due to insufficient sensitivity caused by interferences from polyatomic ions. However, reaction of sulphur with oxygen in the hexapole collision cell, combined with monitoring at m/z 48 (for (32)S) or m/z 50 (for (34)S), provided a facile method for metabolite profiling. Detection of m/z 48 was superior in sensitivity to detection of m/z 50.     

ICP–MS with hexapole collision cell for isotope ratio measurements of Ca, Fe, and Se

To avoid mass interferences on analyte ions caused by argon ions and argon molecular ions via reactions with collision gases, an rf hexapole filled with helium and hydrogen has been used in inductively coupled plasma mass spectrometry (ICP–MS), and its performance has been studied. Up to tenfold improvement in sensitivity was observed for heavy elements (m > 100 u), because of better ion transmission through the hexapole ion guide. A reduction of argon ions Ar⁺ and the molecular ions of argon ArX⁺ (X = O, Ar) by up to three orders of magnitude was achieved in a hexapole collision cell of an ICP–MS (“Platform ICP”, Micromass, Manchester, UK) as a result of gas-phase reactions with hydrogen when the hexapole bias (HB) was set to 0 V; at an HB of 1.6 V argon, and argon-based ions of masses 40 u, 56 u, and 80 u, were reduced by approximately four, two, and five orders of magnitude, respectively. The signal-to-noise ratio ⁸⁰Se/ ⁴⁰Ar₂ ⁺ was improved by more than five orders of magnitude under optimized experimental conditions. Dependence of mass discrimination on collision-cell properties was studied in the mass range 10 u (boron) to 238 u (uranium). Isotopic analysis of the elements affected by mass-spectrometric interference, Ca, Fe, and Se, was performed using a Meinhard nebulizer and an ultrasonic nebulizer (USN). The measured isotope ratios were comparable with tabulated values from IUPAC. Precision of 0.26%, 0.19%, and 0.12%, respectively, and accuracy of 0.13% 0.25%, and 0.92%, respectively, was achieved for isotope ratios ⁴⁴Ca/ ⁴⁰Ca and ⁵⁶Fe/⁵⁷Fe in 10 μg L^–1 solution nebulized by means of a USN and for ⁷⁸Se/⁸⁰Se in 100 μg L^–1 solution nebulized by means of a Meinhard nebulizer. Received: 15 December 2000 / Revised: 26 March 2001 / Accepted: 27 March 2001     

电感耦合等离子体质谱法测定高纯氧化钕中的稀土杂质

基于电感耦合等离子体四极杆质谱仪进行Nd_2O_3中稀土杂质测定,着重研究了碰撞反应池技术(CCT)用于基体Nd氧化物和氢氧化物干扰离子的消除.研究表明,以10% O_2-10% Ar-80% He为碰撞反应气,保持反应气流速为0.1 mL/min,并通过调谐仪器参数,获得~(159)Tb, ~(165)Ho, ~(163)Dy 同位素的~(175)TbO, ~(179)DyO和~(181)HoO出现强氧化物峰,通过对这些氧化物离子进行检测而实现Tb, Dy, Ho的定量分析.在优化的条件下,基体导致的氧化物和氢氧化物质谱干扰可降低25～70倍.研究了CCT模式下不同内标元素用于基体效应的校正.结果表明,Re的校正效果最佳.其余La, Ce, Pr,Sm, Eu, Gd, Er, Tm, Yb和Lu等元素采用常规模式测定,其中Pr的测定采用高分辨以消除基体Nd前沿峰干扰.结合干扰系数校正,所建立的方法适用于99.999% Nd_2O_3的纯度分析,RSD小于5%, 加入回收率令人满意.     

Inductively coupled plasma mass spectrometric determination of the absorption of iron in normal women

The determination of iron isotope ratios in blood, without prior sample preparation, using inductively coupled plasma mass spectrometry (ICP-MS) with sample introduction by electrothermal vaporisation (ETV) is described. Following oral administration of 5 mg of enriched 54FeSO4 and intravenous administration of 200 micrograms of 57FeSO4 to non-pregnant women, the 54Fe: 56Fe and 57Fe: 56Fe isotope ratios in serum were measured reliably within 20 min per sample in quintuplicate. Changes in the fractional absorption of iron during human pregnancy could therefore be assessed.     

Liquid chromatography with electrospray ion-trap mass spectrometry for the determination of anatoxins in cyanobacteria and drinking water

Anatoxin-a (AN) and homoanatoxin-a (HMAN) are potent neurotoxins produced by a number of cyanobacterial species. A new, sensitive liquid chromatography/multiple tandem mass spectrometry (LC/MS(n)) method has been developed for the determination of these neurotoxins. The LC system was coupled, via an electrospray ionisation (ESI) source, to an ion-trap mass spectrometer in positive ion mode. The [M+H](+) ions at m/z 166 (anatoxin-a) and m/z 180 (homoanatoxin-a) were used as the precursor ions for multiple MS experiments. MS(2)bond;MS(4) spectra displayed major fragment ions at m/z 149 (AN), 163 (HMAN), assigned to [Mbond;NH(3)+H](+); m/z 131 (AN), 145 (HMAN), assigned to [Mbond;NH(3)bond;H(2)O+H](+), and m/z 91 [C(7)H(7)](+). Although the chromatographic separation of these neurotoxins is problematic, reversed-phase LC, using a C(18) Luna column, proved successful. Calibration data for anatoxin-a using spiked water samples (10 mL) in LC/MS(n) modes were: LC/MS (25-1000 microg/L), r(2) = 0.998; LC/MS(2) (5-1000(microg/L), r(2) = 0.9993; LC/MS(3) (2.5-1000 microg/L), r(2) = 0.9997. Reproducibility data (% RSD, N = 3) for each LC/MS(n) mode ranged between 2.0 at 500 microg/L and 7.0 at 10 microg/L. The detection limit (S/N = 3) for AN was better than 0.03 ng (on-column) for LC/MS(3) which corresponded to 0.6 microg/L.     

Isotope fractionation of iron(III) in chemical exchange reactions using solvent extraction with crown ether

This work reports on the chemical isotope fractionation of Fe(III) by a solvent extraction method with a crown ether of dicyclohexano-18-crown-6. The (56)Fe/(54)Fe and (57)Fe/(54)Fe ratios were analyzed by multiple-collector inductively coupled plasma mass spectrometry. We determined the dependence of the isotope enrichment factors (epsilon) on the strength of HCl. The relative deviation of the (56)Fe/(54)Fe ratios relative to the unprocessed material (10(4) epsilon(56)) increases from -15.3 to -6.3 with [HCl] increasing from 1.6 to 3.5 mol/L. Likewise, 10(4) epsilon(57) increases from -22.8 to -9.6 under the same conditions. The correlation between epsilon(56) and epsilon(57) is mass dependent within the errors. The observed fractionation was broken down into the effects of competing extraction reactions and of a reaction between Fe(III) species (FeCl(2)(+) and FeCl(3)) in the aqueous phase. We found that the isotope fractionation between the Fe(III) species is mass dependent, which we confirmed by calculating the reduced partition function ratios.     

Reaction chemistry and collisional processes in multiple devices for resolving isobaric interferences in ICP-MS

A low-level review of the fundamentals of ion-molecule interactions is presented. These interactions are used to predict the efficiencies of collisional fragmentation, energy damping and reaction for a variety of neutral gases as a function of pressure in a rf-driven collision/reaction cell. It is shown that the number of collisions increases dramatically when the ion energies are reduced to near-thermal (< 0.1 eV), because of the ion-induced dipole and ion-dipole interaction. These considerations suggest that chemical reaction can be orders of magnitude more efficient at improving the analyte signal/background ratio than can collisional fragmentation. Considerations that lead to an appropriate selection of type of gas, operating pressure, and ion energies for efficient operation of the cell for the alleviation of spectral interferences are discussed. High efficiency (large differences between reaction efficiencies of the analyte and interference ions, and concomitant suppression of secondary chemistry) might be required to optimize the chemical resolution (determination of an analyte in the presence of an isobaric interference) when using ion-molecule chemistry to suppress the interfering ion. In many instances atom transfer to the analyte, which shifts the analytical m/z by the mass of the atom transferred, provides high chemical resolution, even when the efficiency of reaction is relatively low. Examples are given of oxidation, hydroxylation, and chlorination of analyte ions (V+, Fe+, As+, Se+, Sr+, Y+, and Zr+) to improve the capability of determination of complex samples. Preliminary results are given showing O-atom abstraction by CO from CaO+ to enable the determination of Fe in high-Ca samples.     

Determination of nifursol metabolites in poultry muscle and liver tissue. Development and validation of a confirmatory method

A method is described for the identification and quantitative determination of 3,5-dinitrosalicylic acid hydrazide (DSH), the marker residue of nifursol metabolites in poultry (turkey, broiler) muscle and liver tissue. The method is based on the acid-catalysed hydrolysis of tissue-bound metabolites to free DSH and in situ derivatisation with 2-nitrobenzaldehyde to the corresponding nitrophenyl derivative NPDSH. A structural analogue of DSH, 4-hydroxy-3,5-dinitrobenzoic acid hydrazide (HBH) was synthesised to serve as an internal standard. The analytes were isolated from the matrix by liquid-liquid extraction with ethyl acetate. Determination was performed by LC-MS/MS with negative electrospray ionisation. The [M - H](+) ions of NPDSH and NPHBH at m/z 374 were fragmented by collision induced dissociation (CID) producing transition ions at m/z 182, 183 and 226. The transition ions at m/z 182 and 226 were selected for monitoring of NPDSH while the transition ion at m/z 183 was selected for NPHBH. The method has been validated according to the EU criteria of Commission Decision 2002/657/EC at 0.5, 1.0 and 1.5 microg kg(-1) in muscle and liver tissue. A decision limit (CC(alpha)) was obtained of 0.04 and 0.025 microg kg(-1) in muscle and liver, respectively. Similarly a detection capability (CC(beta)) was obtained of 0.10 and 0.05 microg kg(-1) in muscle and liver, respectively. The introduction of HBH as an internal standard did not lead to a significant improvement of the quantitative performance of the method. In fact for liver better performance characteristics were obtained when the IS was not taken into account. Nevertheless, as a qualitative marker for recovery, HBH could still be very useful in the analysis of unknown samples.     

Chemical profile of meta-chlorophenylpiperazine (m-CPP) in ecstasy tablets by easy ambient sonic-spray ionization, X-ray fluorescence, ion mobility mass spectrometry and NMR

Meta-chlorophenylpiperazine (m-CPP) is a new illicit drug that has been sold as ecstasy tablets. Easy ambient sonic-spray ionization mass spectrometry (EASI-MS) and X-ray fluorescence spectrometry (XRF) are shown to provide relatively simple and selective screening tools to distinguish m-CPP tablets from tablets containing amphetamines (mainly 3,4-methylenedioxymethamphetamine (MDMA)). EASI-MS detects the active ingredients in their protonated forms: [m-CPP + H](+) of m/z 197, [MDMA + H](+) of m/z 194, and [2MDMA + HCl + H](+) of m/z 423 and other ions from excipients directly on the tablet surface, providing distinct chemical fingerprints. XRF identifies Cl, K, Ca, Fe, and Cu as inorganic ingredients present in the m-CPP tablets. In contrast, higher Cl concentrations and a more diverse set of elements (P, Cl, Ca, Fe, Cu, Zn, Pt, V, Hf, Ti, Pt, and Zr) were found in MDMA tablets. Principal component analysis applied to XRF data arranged samples in three groups: m-CPP tablets (four samples), MDMA tablets (twenty three samples), and tablets with no active ingredients (three samples). The EASI-MS and XRF techniques were also evaluated to quantify m-CPP in ecstasy tablets, with concentrations ranging from 4 to 40 mg of m-CPP per tablets. The m-CPP could only be differentiated from its isomers (o-CPP and for the three isomers p-CPP) by traveling wave ion mobility mass spectrometry and NMR measurements.