WC/CNT纳米复合材料制备及其对甲醇氧化的电催化性能

采用表面修饰技术将碳纳米管(CNT)表面羧基化, 通过羧基将钨离子基团修饰到碳纳米管的外表面, 再通过原位还原碳化技术, 将钨离子基团还原成碳化钨(WC)纳米微粒, 制备出WC/CNT纳米复合材料. 采用FTIR、XRD、SEM、HRTEM和N2吸附等分析测试手段对样品的形貌、晶相组成和微观结构特征进行了表征. FTIR和N2吸附结果表明, 硝化后, 在碳纳米管表面羧基化的同时比表面积增加; XRD结果表明, WC/CNT样品由碳纳米管、WC以及非化学计量比的氧化钨组成; SEM和HRTEM结果表明, WC纳米颗粒均匀地分散于碳纳米管的外表面,并与碳纳米管构成了复合材料. 采用循环伏安法测试了样品在碱性条件下对甲醇氧化的电催化性能, 结果表明, 复合材料对甲醇氧化的电催性能明显强于WC 和碳纳米管, 并在实验结果的基础上探讨了复合材料催化性能提高的原因.     

Facile synthesis of Fe3O4/reduced graphene oxide/polyvinyl pyrrolidone ternary composites and their enhanced microwave absorbing properties

In this paper, ternary nanocomposites of Fe₃O₄/reduced graphene oxide/polyvinyl pyrrolidone (Fe₃O₄/rGO/PVP) as a novel type of electromagnetic microwave absorbing materials were synthesized by a three-step chemical approach. First, Fe₃O₄ nanospheres were made by solvent thermal method. Successively, the Fe₃O₄ particles were assembled with rGO after having activated by para-aminobenzoic acid. PVP grafting and reduction of GO happened simultaneously in the third step. It is found that the electromagnetic absorption (EA) performance of synthesized ternary composites with suitable PVP amount had been significantly enhanced comparing to Fe₃O₄ and Fe₃O₄/rGO. Merely 15?wt% low loading in paraffin and thin as 2.8?mm can reach effective EA bandwidth (below ?10 Db) of 11.2?GHz, and the highest reflection loss reached ?67?dB at 10.7?GHz. It was demonstrated that these composites show an effective route to novel microwave absorbing material design.     

聚吡咯/铁酸镍纳米复合材料制备和应用研究

以FeCl_3为氧化剂和掺杂剂经原位氧化聚合制备了聚吡咯/铁酸镍纳米复合材料,用以吸附处理废液中高浓度的铬(Ⅵ)。分别采用X射线衍射仪(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)和振动样品磁强计(VSM)对产物的结构、形貌与磁性能进行了表征。结果表明,复合吸附材料由20~30nm大小的NiFe_2O_4多晶球簇内核及外层聚吡咯包覆而成,其饱和磁化强度为7.89emu/g。对含铬(Ⅵ)污水吸附研究表明,该吸附剂在60min内即可达到吸附平衡,吸附效果优异,同时考察了NiFe_2O_4掺杂比例、吸附时间、pH、铬(Ⅵ)初始浓度对吸附效果的影响。在pH=5的条件下,聚吡咯/铁酸镍复合材料在30min内对铬(Ⅵ)的最大吸附量为49.81mg/g。     

Fabrication,characterization and X-band microwave absorption properties of PAni/Fe3O4/PVA nanofiber composites materials

This work presents a study of microwave absorption properties of PAni/Fe₃O₄/PVA nanofiber composites with different ratio of Fe₃O₄ nanoparticles. The morphology of the composites nanofibers study by Field Emission Scanning Electron Microscopes (FESEM) and Transmission Electron Microscope (TEM) showed that the low content of Fe₃O₄ nanoparticles presence in the composites nanofibers indicates very much uniform surface, in the composites nanofiber without many bends, but some bends develop at higher content of Fe₃O₄ nanoparticles as indicated in the TEM image. Image-J software was used to further investigate the diameter of the composites nanofiber and found to be in the range of 152 to 195 nm. The nanofiber composites show excellent electric and magnetic properties and therefore vary with the addition of Fe₃O₄ nanoparticles in the composites nanofiber. In addition the PAni/Fe₃O₄/PVA composites nanofibers were further characterized by X-ray diffraction spectra (XRD) and Four Transformation infrared spectra (FTIR). The XRD pattern shows the presence of PAni nanotubes containing Fe₃O₄ nanoparticles by indicating peaks at 23.4⁰ and 35.43⁰ which was further supported by FTIR analysis. Microwave vector network analyzers (MVNA) were used to estimate the microwave absorption properties of the composites nanofibers. The absorption parameters was found to be −6.4 dB at 12.9 GHz within the range of X-band microwave absorption frequency, this reflection loss is attributed to the multiple absorption mechanisms as a result of the improved of impedance matching between dielectric and magnetic loss of the absorbent materials demonstrating that these materials can be used as protective material for electromagnetic radiation.     

Thermal,mechanical and electroactive shape memory properties of polyurethane (PU)/poly (lactic acid) (PLA)/CNT nanocomposites

Polymer blend nanocomposites based on thermoplastic polyurethane (PU) elastomer, polylactide (PLA) and surface modified carbon nanotubes were prepared via simple melt mixing process and investigated for its mechanical, dynamic mechanical and electroactive shape memory properties. Chemical and structural characterization of the polymer blend nanocomposites were investigated by Fourier Transform infrared (FT-IR) and wide angle X-ray diffraction (WAXD). Loading of the surface modified carbon nanotube in the PU/PLA polymer blends resulted in the significant improvement on the mechanical properties such as tensile strength, when compared to the pure and pristine CNT loaded polymer blends. Dynamic mechanical analysis showed that the glass transition temperature (T_g) of the PU/PLA blend slightly increases on loading of pristine CNT and this effect is more pronounced on loading surface modified CNTs. Thermal and electrical properties of the polymer blend composites increases significantly on loading pristine or surface modified CNTs. Finally, shape memory studies of the PU/PLA/modified CNT composites exhibit a remarkable recoverability of its shape at lower applied dc voltages, when compared to pure or pristine CNT loaded system.     

Nanocomposites NiFe2O4/SiO2 and CoFe2O4/SiO2-Preparation by Sol-Gel Method and Physical Properties

This paper aims to characterise the systems NiFe₂O₄/SiO₂ and CoFe₂O₄/SiO₂ prepared by the sol-gel method. After heat treatment, the various samples have been studied by means of X-ray diffraction, Mössbauer spectroscopy, magnetic measurements and transmission electron microscopy (HR TEM).X-ray diffraction and Mössbauer spectra confirmed the presence of the spinel phase. HR TEM observations revealed the nanocrystals with the size in the range of 2–25 nm. Magnetic measurements showed a superparamagnetic behaviour of the samples heated at lower temperature (800°C) and ferrimagnetic character for the samples heated at higher temperature (900, 1000°C).The final phase composition of the heated samples depends on the preparation conditions. The samples, treated up to 300°C in vacuum and then subsequently heated at 800°C or 900°C, do not contain hematite (the most stable phase at higher temperatures). On the contrary, the samples heated at 1000°C or 1250°C display certain content of hematite.     

Polyaniline/CoFe2O4 nanocomposite inhibits the growth of Candida albicans 077 by ROS production

In recent years, polyaniline/CoFe₂O₄ nanocomposites have gained attention because of their wide utilization in optoelectronics and biomedical studies. However, very limited research has been carried out on the anticandidal activity of polyaniline/CoFe₂O₄ nanocomposite against Candida spp. Thus, the study was designed to investigate the anticandidal potential of PANI/CoFe₂O₄ nanocomposite against Candida albicans 077. PANI/CoFe₂O₄ nanocomposite (denoted as “cfPNCs”) was synthesized by polymerization of aniline in the presence of CoFe₂O₄ nanoparticles. The structural and thermal properties of the synthesized PANI/CoFe₂O₄ nanocomposite were investigated. It was noteworthy that PANI/CoFe₂O₄ nanocomposite showed promising anticandidal activity in a dose-dependent manner. Results also showed that the protection of histidine (a ROS quencher) against ROS clearly suggested the implication of ROS in anticandidal activity of PANI/CoFe₂O₄ nanocomposite. It is encouraging to conclude that PANI/CoFe₂O₄ nanocomposite bears the potential of their applications in biomedicine, especially nanotherapy for diseases caused by C. albicans.     

磁电CoFe2O4/BaTiO3纳米管的溶胶-凝胶模板法合成和表征

用溶胶-凝胶模板法合成了 CoFe2O4)/BaTiO3(CFO/BTO)复合纳米管,管的直径约为 100、200 和 300 nm,其长度约为100 μm.x射线衍射(xRD)和选区电子衍射(sAED)都显示复合纳米管中同时存在尖晶石相的CoFe2O4(CFO)和钙钛矿相的 BaTiO3(BTO),进一步的透射电子显微镜(TEM)研究证实合成的纳米复合物具有明显的管状结构.磁、电研究表明,该复合纳米管的磁性与纯 CFO 纳米管的磁性相当;而铁电性与纯BTO纳米管的铁电性相当.     

Synthesis,characterization and microwave absorption properties of polyaniline/Sm-doped strontium ferrite nanocomposite

Sm-doped strontium ferrite nanopowders (SrSm_0.3Fe_11.7O₁₉) and their composites of polyaniline (PANI)/SrSm_0.3Fe_11.7O₁₉ with 10 wt% and 20 wt% ferrite were prepared by a sol–gel method and an in-situ polymerization process, respectively. The structure, magnetic properties and microwave absorption properties of the samples were characterized by means of X-ray diffraction (XRD), Fourier transform infrared spectra (FT-IR), transmission electron microscope (TEM), vibrating sample magnetometer (VSM) and vector network analyzer, respectively. The particle size of SrSm_0.3Fe_11.7O₁₉ was about 35 nm by using XRD. The ferrite successfully packed by PANI. PANI/SrSm_0.3Fe_11.7O₁₉ possessed the best absorption property with the optimum matching thickness of 3 mm in the frequency of 2–18 GHz. The value of the maximum reflection loss (RL) were −26.0 dB at 14.2 GHz with the 6.5 GHz bandwidth and −24.0 dB at 13.8 GHz with the 7.9 GHz bandwidth for the samples with 10 wt% and 20 wt% ferrite, respectively.     

Preparation of mesoporous TiO2/CNT nanocomposites by synthesis of mesoporous titania via EISA and their photocatalytic degradation under visible light irradiation

Stabilized mesoporous TiO₂ was synthesized by evaporation induced self assembly (EISA) method and mechanically incorporated into single-walled carbon nanotubes (SWCNT) with different ratios. The physicochemical properties of the nanocomposites (mesoporous TiO₂/SWCNT) materials were investigated by Brunauer–Emmett–Teller (BET) measurement, X-ray diffraction (XRD), transmission electron microscopy (TEM), energy dispersive X-ray (EDX), photoluminescence (PL) and ultraviolet–visible (UV–Vis) spectroscopy measurements. The catalytic activity of mesoporous TiO₂ and nanocomposites were assessed by examining the degradation of rhodamine B as model aqueous solution under visible light. CNTs are facilitating the photocatalytic activity of mesoporous TiO₂ in the degradation of rhodamine B efficiently.     

多壁碳纳米管负载Fe3O4磁性纳米粒子表面吸附增强过氧化酶的催化活性

采用共沉淀法制备了Fe3O4磁性纳米粒子,将其负载于氨基吡啶修饰多壁碳纳米管(MWCNT-AP)上,得到具有良好的分散性和超顺磁性的Fe3O4/MWCNT-AP复合物.通过傅里叶变换红外(FT-IR)光谱、X射线衍射(XRD)和磁滞回线测量等方法对Fe3O4/MWCNT-AP复合物进行了表征.扫描电镜(TEM)结果表明:Fe3O4磁性纳米粒子多集中于碳纳米管MWCNT-AP的端部,形成的复合物在极性溶剂中具有良好的分散性和超顺磁性;辣根过氧化酶(HRP)可通过物理作用吸附于Fe3O4/MWCNT-AP复合物表面.酸性条件下(pH 4.0),Fe3O4/MWCNT-AP复合物使HRP的最大反应速率(Vmax)提高了3倍.     

Preparation of CoFe2O4/sawdust and NiFe2O4/sawdust magnetic nanocomposites for removal of oil from the water surface

In this study, CoFe₂O₄/Sawdust and NiFe₂O₄/Sawdust magnetic nanocomposites were synthesized using a hydrothermal method, and then characterized using X-ray powder diffraction, Infrared, scanning electron microscopy, Brunauer–Emmett–Teller/Barrett–Joyner–Halenda, and vibrating-sample magnetometer techniques. In this study, unmodified sawdust (US), modified sawdust (MS), unmodified CoFe₂O₄/sawdust (UCS), modified CoFe₂O₄/sawdust (MCS), unmodified NiFe₂O₄/sawdust (UNS), and modified NiFe₂O₄/Sawdust (MNS) magnetic nanocomposites, which are inexpensive, economical, environmentally friendly absorbents, and have a high selective hydrophobic, were used for the removal of oil from the water surface. The results show that the UCS, MCS, UNS, and MNS magnetic nanocomposites can selectively absorb the oil spreading on the water surface, due to its superhydrophobicity and superoleophilicity, and can be easily collected from water under the influence of a magnetic field. In addition, the results showed that the absorbents reach their equilibrium at the 30-min mark. Among all the absorbents, the MNS magnetic nanocomposite showed the maximum absorption capacity (18.172 g/g) at the 40-min mark. The results of the kinetic studies showed that the second-order kinetic equation with the highest correlation coefficient had the best fit with the experimental results.     

CNT/Fe-Ni/TiO_2/ZnO阵列修饰Ni阳极的制备及光催化制氢性能

采用层层自组装方法在Ni片阳极上构建TiO2/Zn O纳米棒阵列,以二氧化钛前驱体溶胶中掺杂的铁和镍为催化剂,通过气相沉积法在TiO2/Zn O纳米棒阵列间原位生长碳纳米管(CNTs),得到CNT/Fe-Ni/TiO2/Zn O复合光催化剂修饰的光活性Ni片阳极.以碱性电解池为基础,用紫外线辐照修饰的Ni阳极实现光催化和电解水的有机耦合制氢过程.通过场发射扫描电子显微镜(FESEM)、透射电子显微镜(TEM)、拉曼光谱(Raman)和电化学阻抗谱(EIS)对CNT/Fe-Ni/TiO2/Zn O复合膜光催化剂的结构进行了表征,并测试了其光催化辅助电解水制氢(WEAP)活性.结果表明,生长了碳纳米管的光催化复合膜CNT/Fe-Ni/TiO2/Zn O修饰的Ni阳极的产氢速率分别比Fe-Ni/TiO2/Zn O修饰的Ni阳极和纯Ni片提高了93.7%和533.0%.     

表面活性剂对TiO_2/CNT苯酚与碳酸二甲酯酯交换活性的影响

以表面活性剂十六烷基三甲基溴化铵（CTAB）和十二烷基硫酸钠（SDS）改性的碳纳米管为载体,制备了TiO2/CNT催化剂,用于苯酚与碳酸二甲酯酯交换合成碳酸二苯酯的反应.采用X射线衍射（XRD）、扫描电镜（SEM）和透射电镜（TEM）对改性前后催化剂的结构和形貌进行了表征,显示出负载后的催化剂中活性组分二氧化钛以无定形...     

Achieving full effective microwave absorption in X band by double-layered design of glass fiber epoxy composites containing MWCNTs and Fe3O4 NPs

The glass fiber epoxy composites containing MWCNTs and Fe₃O₄ NPs were manufactured by composites liquid molding process. The microwave absorbing properties of single-layered and double-layered glass fiber/MWCNTs/epoxy and glass fiber/Fe₃O₄ NPs/epoxy composites were evaluated. The reflection loss(RL) were calculated by the measured complex permittivity and permeability using waveguide method by vector network analyzer. Based on the mechanism analysis and deficiency of single-layer absorber, the double-layered composites were fabricated by using matching layer and absorbing layer to enhance the microwave absorption performance, which can be modulated by tailoring the electromagnetic parameters and thicknesses of each layer. The optimized microwave absorbing properties of double-layered composites with minimum RL of −45.7 dB and full X-band effective absorption can be achieved when the total thickness of the matching layer and absorbing layer is 1.8 mm, which can be attributed to synergistic effect of improved impedance matching characteristic and superior microwave attenuation characteristic of the absorbing layer. The combined utilization of dielectric loss and magnetic loss absorbent and their double-layered structure design shows great design flexibility and diversity and can be a promising candidate for designing high performance microwave absorbing materials.     

纳米复合材料CoFe2O4/SiO2的制备和表征

采用溶胶-凝胶法制备了(CoFe2O4)x/(SiO2)1-x纳米复合材料. 利用TG/DTA, XRD和Mssbauer效应研究了热处理过程中干凝胶的变化及样品的结构、晶粒尺寸和磁性. 结果表明, 随着SiO2含量的增加, 样品中CoFe2O4的晶粒尺寸和内磁场逐渐变小, 并从磁有序状态转变为超顺磁状态.     

Effect of Magnetic Carrier NiFe2O4 Nanoparticles on Physicochemical and Catalytic Properties of Magnetically Separable Photocatalyst TiO2/NiFe2O4

A series of magnetically separable photocatalyst TiO₂/NiFe₂O₄(TN) with different mass ratios of NiFe₂O₄ to TiO₂ was prepared by sol-gel method. The X-ray diffraction(XRD), X-ray photoelectron spectroscopy(XPS), transmission electron microscopy(TEM), ultraviolet-visible spectroscopy(UV-Vis), Brunauer-Emmett-Teller(BET) surface analysis and photoluminescence spectroscopy(PL) were used to characterize the photocatalyst TN. The XRD patterns of TN indicate that adulterating a smidgen of NiFe₂O₄ into TiO₂(about 0.1%, mass ratio) can promote the phase transformation of TiO₂, however, when the doped amount of NiFe₂O₄ surpasses 1%, the introduction of NiFe₂O₄ can inhibit the growth of TiO₂ crystal grain and reduce the size of TiO₂ crystal grain. The XPS results of TN indicate that some Fe³⁺ replace Ti⁴⁺ of the TiO₂ lattice forming Fe―O―Ti bonds. The PL analysis of TN shows that the NiFe₂O₄ nanoparticles in photocatalyst TN play the role of the effective recombination centre of the photogenerated electrons and holes, leading to the decrease in photocatalytic activity.     

Electrochemical Sensing of Flutamide Contained in Plasma and Urine Matrices Using NiFe2O4/rGO Nanocomposite,as an Efficient and Selective Electrocatalyst

In this article, we report on the synthesis and new employment of magnetic nickelferrite oxide nanoparticles decorated reduced graphene oxide (NiFe₂O₄/rGO) to electrochemically sensing of flutamide. The preparation of this electrocatalyst was first assessed using various analytical instrumental techniques including FT‐IR spectroscopy, X‐ray diffraction spectroscopy, energy‐dispersive X‐ray spectroscopy, and field emission scanning and transmission electron microscopy. Besides, its electrochemical performance was investigated utilizing some electrochemical methods such as cyclic and differential pulse voltammetry, and also electrochemical impedance spectroscopy. The findings of this research are especially relevant for sensing flutamide in aqueous and biological samples. At the optimized conditions, the electrochemical sensor showed a linear range of 0.24–40.0 μmol L^?1, the detection limit of 0.05 μmol L^?1 flutamide, calibration sensitivity of 1.016 μA/μmol L^?1, and repeatability and reproducibility of 1.7 % and 4.1 %, respectively. The selectivity of the method was investigated in the presence of ions, and species can generally exist in the biological medium. The resulting data of the present work represented that this type of magnetic nanocomposites is suitable for selective detection of flutamide in real samples of plasma and urine. The recoveries obtained for flutamide analyses represented lower than 5.0 percent of relative error in these real samples.     

Fabrication of Chitosan‐Multiwall Carbon Nanotube Nanocomposite Containing Ferri/Ferrocyanide: Application for Simultaneous Detection of D‐Penicillamine and Tryptophan

We report a simple and effective strategy for fabrication of the nanocomposite containing chitosan (CS) and multiwall carbon nanotube (MWNT) coated on a glassy carbon electrode (GCE). The characterization of the modified electrode (CS‐MWNT/GC) was carried out using scanning electron microscopy (SEM) and UV–vis absorption spectroscopy. The electrochemical behavior of CS‐MWNT/GC electrode was investigated and compared with the electrochemical behavior of chitosan modified GC (CS/GC), multiwalled carbon nanotube modified GC (MWNT/GC) and unmodified GC using cyclic voltammetry (CV) and electron impedance spectroscopy (EIS). The chitosan films are electrochemically inactive; similar background charging currents are observed at bare GC. The chitosan films are permeable to anionic Fe(CN)₆^3?/4? (FC) redox couple. Electrochemical parameters, including apparent diffusion coefficient for the Fe(CN)₆^3?/4? redox probe at FC/CS‐MWNT/GC electrode is comparable to values reported for cast chitosan films. This modified electrode also showed electrocatalytic effect for the simultaneous determination of D‐penicillamine (D‐PA) and tryptophan (Trp). The detection limit of 0.9 μM and 4.0 μM for D‐PA and Trp, respectively, makes this nanocomposite very suitable for determination of them with good sensitivity.     

Synthesis and characterization of 1D Co/CoFe(2)O(4) composites with tunable morphologies

1D Co/CoFe(2)O(4) composites with tunable morphologies were fabricated by a facile solvothermal route in the presence of a surfactant poly(vinylpyrrolidone) (PVP); they may be very attractive for potential applications because of their outstanding soft magnetism.