Bismuth modified carbon-based electrodes for the determination of selected neonicotinoid insecticides

Two types of bismuth modified electrodes, a bismuth-film modified glassy carbon (BiF-GCE) and a bismuth bulk modified carbon paste, were applied for the determination of selected nitroguanidine neonicotinoid insecticides. The method based on an ex situ prepared BiF-GCE operated in the differential pulse voltammetric (DPV) mode was applied to determine clothianidin in the concentration range from 2.5 to 23 μg cm?3 with a relative standard deviation (RSD) not exceeding 1.5%. The tricresyl phosphate-based carbon paste electrodes (TCP-CPEs), bulk modified with 5 and 20 w/w% of bismuth, showed a different analytical performance in the determination of imidacloprid, regarding the peak shape, potential window, and noise level. The TCP-CPE with 5% Bi was advantageous, and the developed DPV method based on it allowed the determination in the concentration range from 1.7 to 60 μg cm?3 with an RSD of 2.4%. To get a deeper insight into the morphology of the bismuth-based sensor surfaces, scanning electron microscopic measurements were performed of both the surface film and the bulk modified electrodes.     

Anodic Stripping Voltammetric Determination of Lead(II) with a 2‐Aminopyridinated‐Silica Modified Carbon Paste Electrode

Abstract

A carbon paste electrode modified with organically functionalized silica was used for the determination of lead. The measurements were carried out in three steps including an open circuit accumulation followed by electrolysis of accumulated lead at the carbon paste electrode and differential pulse voltammetric determination. The effects of several experimental variables such as carbon paste composition, pH and concentration of supporting electrolyte, electrolysis potential, and electrolysis time were studied. The resulting electrode demonstrates linear response over a wide range of Pb(II) concentration (5–1000 ng mL^?1) with an accumulation time of 60 sec. The effects of potential interfering ions were studied, and it was found that the proposed procedure is free from most interferences. Long lifetime and rapid and convenient renewal of electrode surface allows the use of a single modified electrode surface in multiple analytical determinations over at least 4 months. The prepared electrode was used for determination of lead spiked in a hair sample, and very good recovery results were obtained over a wide concentration range of lead.     

Ultra trace level square wave anodic stripping voltammetric sensing of mercury(II) ions in environmental samples using a Schiff base-modified carbon paste electrode

ABSTRACT

In this approach, a new carbon paste electrode modified with N,N′-bis(5-bromo-2-hydroxybenzylidene)-2,2-dimethylpropane-1,3-diamine Schiff base ligand (L) was synthesised for selective and effective determination of Hg²⁺ ions in aqueous environmental samples using cyclic and square wave anodic stripping voltammetric methods. First, the selective detection of mercury ion was confirmed by evaluating the stability constants of metal complexes formed between the Schiff base ligand (L) and some desired cations by conductometric measurements. Afterwards, by preparing an effective carbon paste electrode modified with L, the experimental and instrumental parameters affecting the performance of modified electrode were investigated. Square wave anodic stripping voltammograms were obtained after applying an accumulation potential ?0.5 V and accumulation time 150 s in Britton–Robinson buffer solution at pH 2.0. The optimal square wave parameters found are pulse amplitude 75 mV, frequency 50 Hz and step potential 6 mV. The procedure exhibited linear range from 0.4 to 120 μg L^?1 Hg²⁺ with a limit of detection of 0.042 μg L^?1. The proposed electrode was proved to be highly selective in the presence of various cations and anions and was successfully used for determination of mercury in tobacco and several water samples.     

Synthesis and application of a natural-based nanocomposite with carbon nanotubes for sensitive voltammetric determination of lead (II) ions

ABSTRACT

A modified carbon paste electrode has been developed for the determination of Pb(ΙΙ) ions based on Fe₃O₄/eggshell magnetic nanocomposite. The structure and morphology of Fe₃O₄/eggshell were analysed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The prepared nanocomposite was also characterized by Fourier transform infrared spectroscopy (FT-IR) and vibrating sample magnetometer (VSM). The electrochemical procedure was based on the accumulation and determination of Pb(ΙΙ) ions at the surface of the modified carbon paste electrode with Fe₃O₄/eggshell nanocomposites and carbon nanotubes by differential pulse anodic stripping voltammetry (DPASV). Various experimental parameters involved in the preconcentration of Pb(ΙΙ) ions and voltammetric stripping step were studied. Under the optimum conditions, the voltammetric peak current of Pb(ΙΙ) occurs at a potential about ?0.5 V. Also, the voltammetric peak current increased linearly with Pb(ΙΙ) concentration in the range of 0.5–200 ng mL^?1 and a detection limit of 0.15 ng mL^?1 was obtained for Pb(ΙΙ). The selectivity of the proposed electrode for Pb(ΙΙ) ions in the presence of some cations was also examined. The practical application of the proposed modified electrode was evaluated by the determination of Pb(ΙΙ) ions in human hair and water samples. The results were satisfactory for the spiked samples.     

Sensitive Adsorptive Stripping Voltammetric Methodologies for the Determination of Melatonin in Biological Fluids

The reversible redox process that melatonin presented on carbon paste electrodes was the basis of a sensitive methodology for the determination of this hormone. From all the processes presented by this hormone, this was never used before as the basis of voltammetric measurements for melatonin determination. Therefore, parameters that affected the cyclic voltammetric signal were studied. A limit of detection as low as 9×10^?11 M was obtained when optimized alternating current voltammetry was employed. The reproducibility was excellent due to an adequate pretreatment of the solid electrode (RSD=2.7%, n=10). A comparison with methodologies that employ different electrochemical techniques from the point of view of their analytical characteristics was made. This methodology has proved to be suitable for the determination of melatonin in biological fluids.     

Utilization of Carbon Paste Electrodes for the Voltammetric Determination of Chlortoluron

Conventional (CPE) and miniaturized (m‐CPE) carbon paste electrodes consisting of a carbon paste filled capillary were used for differential pulse voltammetric determination of chlortoluron in samples of river water and soil, in the latter case after the extraction by methanol. Britton‐Robinson buffer pH 3 with low content of methanol was found to be optimal for the determination. The achieved determination limits were 2.8 µmol L^?1 and 0.34 µmol L^?1 in river water, and 3.1 and 4.3 µg g^?1 in soil, using CPE and m‐CPE, respectively.     

Voltammetric Determination of Valaciclovir Using a Molecularly Imprinted Polymer Modified Carbon Paste Electrode

A molecularly imprinted polymer (MIP) was rationally synthesized with the aid of computer based studies. The computational studies were used to screen for the most suitable template to functional monomer molar ratio. Two functional monomers were involved in the study (methacrylic acid and 4‐vinylpyridine). Four MIP ratios were synthesized in accordance with the results of the computational studies and their performance was evaluated using equilibrium rebinding assays. The MIP with the best performance was used as an additive in carbon paste electrodes for the voltammetric determination of valaciclovir (VCV). Following the optimization of voltammetric parameters, a linear response was obtained in the range of 1.0x10⁻⁶–7.0x10⁻⁴ M with a limit of detection at 4.45x10⁻⁷ M. The MIP modified carbon paste electrode was successfully applied for the determination of VCV in pure solutions and dosage form.     

Electrochemistry and Voltammetric Determination of Adenosine with N‐Hexylpyridinium Hexafluorophosphate Modified Electrode

An ionic liquid N‐hexylpyridinium hexafluorophosphate (HPPF₆) modified carbon paste electrode was fabricated for the sensitive voltammetric determination of adenosine in this paper. Carbon ionic liquid electrode (CILE) was prepared by mixing graphite powder and HPPF₆ together and the CILE was characterized by scanning electron microscopy (SEM) and electrochemical methods. The electrochemical behaviors of adenosine on the CILE were studied carefully. Compared with the traditional carbon paste electrode (CPE), a small negative shift of the oxidation peak potential appeared with greatly increase of the oxidation peak current, which indicated the presence of ionic liquid in the carbon paste not only as the binder but also as the modifier and promoter. Under the optimal conditions the oxidation peak current increased with the adenosine concentration in the range from 1.0×10^?6 mol/L to 1.4×10^?4 mol/L with the detection limit of 9.1×10^?7 mol/L (S/N=3) by differential pulse voltammetry. The proposed method was applied to the human urine samples detection with satisfactory results.     

Spectroscopic and voltammetric studies of Pefloxacin bound to calf thymus double-stranded DNA

Spectral and electrochemical studies have been carried out on the interaction of pefloxacin with calf thymus double-stranded dsDNA. The voltammetric behavior of pefloxacin was investigated at glassy carbon, carbon paste and dsDNA-modified carbon paste electrodes using cyclic voltammetry. Pefloxacin was oxidized, yielding one irreversible oxidation peak. The modification of the carbon paste surface with dsDNA allowed an accumulation process to take place for pefloxacin such that higher sensitivity was achieved compared with the bare surface. The response was characterized with respect to ionic strength, accumulation time, pefloxacin concentration, and other variables. The stripping differential pulse voltammetric response showed a linear calibration curve in the range 1.0×10^–7–1.0×10^–5 mol l^–1 with a detection limit of 5.0×10^–8 mol l^–1 at the dsDNA modified electrode. The method was applied to the direct determination of pefloxacin in diluted urine samples.     

Voltammetric Determination of Chlorpheniramine Maleate Based on the Enhancement Effect of Sodium‐dodecyl Sulfate at Carbon Paste Electrode

The voltammetric oxidation and determination of chlorpheniramine maleate (CPM) was studied at a carbon paste electrode (CPE) in the presence of sodium‐dodecyl sulfate (SDS) by cyclic and differential pulse voltammetry. The results indicated that the voltammetric response of chlorpheniramine maleate was markedly increased in the low concentration of SDS, suggesting that SDS exhibits observable enhancement effect to the determination of chlorpheniramine maleate. Under the optimal conditions the peak current was proportional to chlorpheniramine maleate concentration in the range of 8.0×10⁻⁶ to 1.0×10⁻⁴ M with detection limit of 1.7×10⁻⁶ M by differential pulse voltammetry. The proposed method was successfully applied to the determination of chlorpheniramine in pharmaceutical and urine samples.     

Zeolite-Modified Carbon-Paste Electrode as a Selective Voltammetric Sensor for Detection of Tryptophan in Pharmaceutical Preparations

Abstract

Several synthetic zeolites such as mazzite, mordenite, zeolite L, zeolite beta, and MCM-41 were tested as electrode modifiers in voltammetric determination of tryptophan. It was found that addition of zeolite beta to the carbon paste would generate the peak current of Trp because of its catalytic effect. The anodic peak currents were proportional to Trp concentrations in the range of 5.0 × 10^?7 to 5.0 × 10^?3 M. The detection limit was 1.0 × 10^?7 M. The influence of several species, especially other amino acids, were tested. The proposed method was applied successfully to the determination of tryptophan in pharmaceutical formulations.     

Electrochemical Behaviour of Benzofuran Derivatives of Pharmaceutical Interest at Solid Electrodes

Abstract

The electrooxidation of four structually related drugs (amiodarone and benziodarone and their iodinated derivatives), has been studied, using cyclic voltammetry and controlled potential coulometry at carbon paste and platinum electrodes in hydro-organic media. The oxidative mechanisms have been suggested on the basis of a comparative study and by analyzing the i_p, E_p/ pH plots, the number of electrons evolved and the cyclic voltammetric behaviours. The influence of carbon-iodine bonds on the redox pattern of the molecules has been analyzed and a comparison between the oxidation pattern of the phenolic molecules and the corresponding diethylaminoethoxy derivatives has been realized. Quantitative measurements have been obtained at the carbon paste electrode, within the range of concentrations 5. × 10^?6 M - 5 × 10⁵ M. The analytical usefulness in determination of these compounds has been demonstrated.     

Determination of Nanomolar Concentrations of Pb(II) Using Carbon Paste Electrode Modified with Zirconium Phosphated Amorphous Silica

A sensitive and selective method for the determination of Pb(II) with a zirconium phosphated silica gel (SiZrPH) modified carbon paste electrode has been developed. The measurements were carried out in three steps including an open circuit accumulation following by electrolysis of accumulated Pb(II) at the modified carbon paste electrode and differential pulse voltammetric determination. The analytical performance was evaluated with respect to the carbon paste composition, pH of solution at the accumulation step, pH and concentration of supporting electrolyte, electrolysis potential, accumulation time and electrolysis time. Two linear calibration graphs were obtained in the concentration ranges 2.5×10^?9 mol L^?1–5.0×10^?8 mol L^?1 and 5.0×10^?8 mol L^?1–5.0×10^?6 mol L^?1 with an accumulation time of 120 s. The detection limit was found to be 3.5×10^?10 mol L^?1. The effects of potential interfering ions were studied, and it was found that the proposed procedure is free from interferences of common interfering ions such as tin, thallium and etc. The developed method was applied to Pb(II) determination in a wastewater sample.     

Simultaneous Voltammetric Determination of Captopril and Hydrochlorothiazide on a Graphene/Ferrocene Composite Carbon Paste Electrode

In this work, a voltammetric method has been developed for the simultaneous determination of captopril (CPT) and hydrochlorothiazide (HCT) in pharmaceutical combinations and clinical samples using a graphene/ferrocene composite carbon paste (GR/Fc/CP) electrode. The electrochemical behaviors of CPT and HCT were individually and simultaneously investigated at the surface of the GR/Fc/CP electrode. In differential pulse voltammetric (DPV) mode and under optimized experimental conditions, CPT and HCT gave linear responses over the concentration ranges 1.0–430 µM and 0.5–390 µM (r²>0.99), respectively. The prepared electrode could be used for simultaneous determination of CPT and HCT in some real samples.     

Determination of Carbendazim by Adsorptive Stripping Differential Pulse Voltammetry Employing Glassy Carbon Paste Electrode Modified with Graphene and Amberlite XAD 2 Resin

Graphene nanosheets (GNS) and amberlite XAD‐2 (XAD2) modified glassy carbon paste electrode (GNS‐XAD2‐GCPE) were fabricated for voltammetric determination of Carbendazim (MBC). GNS was synthesized by Hummer’s method and characterized by SEM, EDAX, and XRD techniques. After optimizing the analytical conditions in 0.4 M citrate buffer (pH 4.0), the peak current was found to be linear in the range of 8.36×10^?9 to 4.13×10^?6 M (r=0.9986) with detection limit of 3.14×10^?9 M (S/N=3) by AdSDPV. The method was validated for the determination of MBC in soil, fruit, blood serum, urine, waste and ground water samples with satisfactory recoveries.     

Sensing System Integrating Lanthanum Hydroxide Nanowires with Copper(II) Ion for Uracil and its Application

Abstract

A sensing system for uracil was constituted by using lanthanum hydroxide nanowires (LNW) as a modifier to obtain LNW modified carbon paste electrode (LNW/CPE) and by introducing copper(II) ion into supporting electrolyte to transform electroinactive uracil to electroactive uracil‐Cu(II) complex. The voltammetric behaviors of uracil in the presence of Cu(II) ion at LNW/CPE were investigated. A reduction peak of the uracil‐Cu(II) complex at ?0.18 V was the two‐electron reduction of Cu(II) ion in the uracil‐Cu(II) complex; while a new oxidation peak at 0.22 V was the one‐electron oxidation of the uracil‐Cu(I) complex. Additionally, the voltammetric responses of all the complexes at LNW/CPE were more sensitive than that at carbon and multiwall carbon nanotube paste electrodes, which resulted from both the large surface effect of LNW and the chemical coordination of uracil with La(III) ion in LNW. With the sensitive oxidation peak of the uracil‐Cu(I) complex at LNW/CPE, a linear range of 4.0×10^?9?3.0×10^?8 mol/l for uracil was obtained along with a detection limit of 2.0×10^?10 mol/l. The proposed system was evaluated by the determination of uracil derivatives, anticancer drug 5‐flurouracil, in pharmaceutical preparations.     

Carbon Paste Electrode Incorporating 1‐[4‐(Ferrocenyl Ethynyl) Phenyl]‐1‐Ethanone for Electrocatalytic and Voltammetric Determination of Tryptophan

A carbon paste electrode spiked with 1‐[4‐ferrocenyl ethynyl) phenyl]‐1‐ethanone (4FEPE) was constructed by incorporation of 4FEPE in graphite powder‐paraffin oil matrix. It has been shown by direct current cyclic voltammetry and double step chronoamperometry that this electrode can catalyze the oxidation of tryptophan (Trp) in aqueous buffered solution. It has been found that under optimum condition (pH 7.00), the oxidation of Trp at the surface of such an electrode occurs at a potential about 200 mV less positive than at an unmodified carbon paste electrode. The kinetic parameters such as electron transfer coefficient, α and rate constant for the chemical reaction between Trp and redox sites in 4FEPE modified carbon paste electrode (4FEPEMCPE) were also determined using electrochemical approaches. The electrocatalytic oxidation peak current of Trp showed a linear dependent on the Trp concentrations and linear calibration curves were obtained in the ranges of 6.00×10^?6 M–3.35×10^?3 M and 8.50×10^?7 M–6.34×10^?5 M of Trp concentration with cyclic voltammetry (CV) and differential pulse voltammetry (DPV) methods, respectively. The detection limits (3σ) were determined as 1.80×10^?6 M and 5.60×10^?7 M by CV and DPV methods. This method was also examined as a selective, simple and precise new method for voltammetric determination of tryptophan in real sample.     

Voltamperometric determination of kinetin with a carbon paste modified electrode

The electrochemical behaviour of kinetin (6-furfurylaminopurine) on a carbon paste modified with OV-17 silicone electrode, is studied. The determination of kinetin is possible working in square wave voltammetric techniques, reaching limits of determination of 38.7 ng ml⁻¹. The proposed method was successfully applied to determine the cytokinin in extracts of apples (previously spiked with kinetin) and the obtained results were in accordance with the results obtained with HPLC-UV.     

Anodic Stripping Voltammetric Determination of Mercury in Water Using a Chitosan‐Modified Carbon Paste Electrode

Abstract

This paper describes the preparation and electrochemical application of a modified carbon paste electrode with chitosan for the determination of Hg(II) ions in water using anodic stripping voltammetry. Experimental parameters, including the pH of the supporting electrolyte, time and potential of accumulation and scan rate were investigated. The best voltammetric response was observed for a paste composition of 60% (m/m) of graphite powder, 20% (m/m) of chitosan and 20% (m/m) of mineral oil, with 0.1 mol/l NaNO₃ solution at pH 6.3 as supporting electrolyte, a preconcentration potential of ?0.2 V, preconcentration time of 270 s and a scan rate of 25 mV/s. Under these optimal experimental conditions, the voltammetric signals were linearly dependent on the Hg(II) concentration in the range of 9.99×10^?7 to 3.85×10^?5 mol/l with a detection limit of 6.28×10^?7 mol/l. Three “spiked” samples of water were evaluated using the proposed sensor, and results agreed with those obtained by a reference method at the 95% confidence level.     

Adsorptive Stripping Voltammetric Determination of Nanomolar Concentration of Cerium(III) at a Carbon Paste Electrode Modified by N′‐[(2‐Hydroxyphenyl)Methylidene]‐2‐Furohydrazide

The aim of this work was to obtain an adsorptive stripping voltammetric method for the Ce(III) determination at a carbon paste electrode, chemically modified with N'‐[(2‐hydroxyphenyl)methylidene]‐2‐furohydrazide (NHMF). The electroanalytical procedure comprised two steps: the Ce(III) chemical accumulation at ?200 mV followed by the electrochemical detection of the Ce(III)/NHMF complex, using anodic stripping voltammetry. The factors, influencing the adsorptive stripping performance, were optimized including the modifier quantity in the paste, the electrolyte concentrations, the solution pH and the accumulation potential or time. The resulting electrode demonstrated a linear response over a wide range of Ce(III) concentration (5.0–90 nmol dm^?3). The detection limit was found to be 0.8 nmol dm^?3 on the basis of a signal to noise ratio of 3. The precision for six determinations of 10 and 55 nmol dm^?3 Ce(III) was 5.6% and 2.1% (relative standard deviation), respectively. Application of the procedure to the determination of cerium in phosphate rock and wastewater samples gave good results.