Green ultrasound-assisted extraction of carotenoids based on the bio-refinery concept using sunflower oil as an alternative solvent

A green, inexpensive and easy-to-use method for carotenoids extraction from fresh carrots assisted by ultrasound was designed in this work. Sunflower oil was applied as a substitute to organic solvents in this green ultrasound-assisted extraction (UAE): a process which is in line with green extraction and bio-refinery concepts. The processing procedure of this original UAE was first compared with conventional solvent extraction (CSE) using hexane as solvent. Moreover, the UAE optimal conditions for the subsequent comparison were optimized using response surface methodology (RSM) and ultra performance liquid chromatography – diode array detector – mass spectroscopy (UPLC–DAD–MS). The results showed that the UAE using sunflower as solvent has obtained its highest β-carotene yield (334.75 mg/l) in 20 min only, while CSE using hexane as solvent obtained a similar yield (321.35 mg/l) in 60 min. The green UAE performed under optimal extraction conditions (carrot to oil ratio of 2:10, ultrasonic intensity of 22.5 W cm^?2, temperature of 40 °C and sonication time of 20 min) gave the best yield of β-carotene.     

Intensification of extraction of curcumin from Curcuma amada using ultrasound assisted approach: Effect of different operating parameters

Curcumin, a dietary phytochemical, has been extracted from rhizomes of Curcuma amada using ultrasound assisted extraction (UAE) and the results compared with the conventional extraction approach to establish the process intensification benefits. The effect of operating parameters such as type of solvent, extraction time, extraction temperature, solid to solvent ratio, particle size and ultrasonic power on the extraction yield have been investigated in details for the approach UAE. The maximum extraction yield as 72% was obtained in 1 h under optimized conditions of 35 °C temperature, solid to solvent ratio of 1:25, particle size of 0.09 mm, ultrasonic power of 250 W and ultrasound frequency of 22 kHz with ethanol as the solvent. The obtained yield was significantly higher as compared to the batch extraction where only about 62% yield was achieved in 8 h of treatment. Peleg’s model was used to describe the kinetics of UAE and the model showed a good agreement with the experimental results. Overall, ultrasound has been established to be a green process for extraction of curcumin with benefits of reduction in time as compared to batch extraction and the operating temperature as compared to Soxhlet extraction.     

Ultrasound induced green solvent extraction of oil from oleaginous seeds

Ultrasound-assisted extraction of rapeseed oil was investigated and compared with conventional extraction for energy efficiency, throughput time, extraction yield, cleanness, processing cost and product quality. A multivariate study enabled us to define optimal parameters (7.7 W/cm² for ultrasonic power intensity, 40 °C for processing temperature, and a solid/liquid ratio of 1/15) for ultrasound-assisted extraction of oil from oilseeds to maximize lipid yield while reducing solvent consumption and extraction time using response surface methodology (RSM) with a three-variable central composite design (CCD). A significant difference in oil quality was noted under the conditions of the initial ultrasound extraction, which was later avoided using ultrasound in the absence of oxygen. Three concepts of multistage cross-current extraction were investigated and compared: conventional multistage maceration, ultrasound-assisted maceration and a combination, to assess the positive impact of using ultrasound on the seed oil extraction process. The study concludes that ultrasound-assisted extraction of oil is likely to reduce both economic and ecological impacts of the process in the fat and oil industry.     

Green ultrasound-assisted extraction of carotenoids from pomegranate wastes using vegetable oils

The objective of this work was to develop a new process for pomegranate peels application in food industries based on ultrasound-assisted extraction of carotenoids using different vegetable oils as solvents. In this way, an oil enriched with antioxidants is produced. Sunflower oil and soy oil were used as alternative solvents and the effects of various parameters on extraction yield were studied. Extraction temperature, solid/oil ratio, amplitude level, and extraction time were the factors investigated with respect to extraction yield. Comparative studies between ultrasound-assisted and conventional solvent extraction were carried out in terms of processing procedure and total carotenoids content. The efficient extraction period for achieving maximum yield of pomegranate peel carotenoids was about 30 min. The optimum operating conditions were found to be: extraction temperature, 51.5 °C; peels/solvent ratio, 0.10; amplitude level, 58.8%; solvent, sunflower oil. A second-order kinetic model was successfully developed for describing the mechanism of ultrasound extraction under different processing parameters.     

Development and validation of an efficient ultrasound assisted extraction of phenolic compounds from flax (Linum usitatissimum L.) seeds

Flaxseed accumulates in its seedcoat a macromolecular complex composed of lignan (secoisolariciresinol diglucoside, SDG), flavonol (herbacetin diglucoside, HDG) and hydroxycinnamic acids (p-couramic, caffeic and ferulic acid glucosides). Their antioxidant and/or cancer chemopreventive properties support their interest in human health and therefore, the demand for their extraction. In the present study, ultrasound-assisted extraction (UAE) of flaxseed phenolic compounds was investigated. Scanning Electron Microscopy imaging and histochemical analysis revealed the deep alteration of the seedcoat ultrastructure and the release of the mucilage following ultrasound treatment. Therefore, this method was found to be very efficient for the reduction of mucilage entrapment of flaxseed phenolics. The optimal conditions for UAE phenolic compounds extraction from flaxseeds were found to be: water as solvent supplemented with 0.2 N of sodium hydroxide for alkaline hydrolysis of the SDG–HMG complex, an extraction time of 60 min at a temperature of 25 °C and an ultrasound frequency of 30 kHz. Under these optimized and validated conditions, highest yields of SDG, HDG and hydroxycinnamic acid glucosides were detected in comparison to other published methods. Therefore, the procedure presented herein is a valuable method for efficient extraction and quantification of the main flaxseed phenolics. Moreover, this UAE is of particular interest within the context of green chemistry in terms of reducing energy consumption and valuation of flaxseed cakes as by-products resulting from the production of flax oil.     

Kinetics of ultrasound-assisted extraction of antioxidant polyphenols from food by-products: Extraction and energy consumption optimization

Ultrasound-assisted extraction (UAE) of antioxidant polyphenols from chicory grounds was studied in order to propose a suitable valorization of this food industry by-product. The main parameters influencing the extraction process were identified. A new mathematical model for multi-criteria optimization of UAE was proposed. This kinetic model permitted the following and the prediction of the yield of extracted polyphenols, the antioxidant activity of the obtained extracts and the energy consumption during the extraction process in wide ranges of temperature (20–60 °C), ethanol content in the solvent (0–60% (vol.) in ethanol–water mixtures) and ultrasound power (0–100 W). After experimental validation of the model, several simulations at different technological restrictions were performed to illustrate the potentiality of the model to find the optimal conditions for obtaining a given yield within minimal process duration or with minimal energy consumption. The advantage of ultrasound assistance was clearly demonstrated both for the reduction of extraction duration and for the reduction of energy consumption.     

Effects of various factors of ultrasonic treatment on the extraction yield of all-trans-lycopene from red grapefruit (Citrus paradise Macf.)

The effects of various factors, including the extraction time, temperature, solvent/material ratio, the ultrasonic intensity and duty cycle of ultrasonic irradiation on the extraction yield of all-trans-lycopene from red grapefruit by ultrasound-assisted extraction (UAE) were investigated. In comparison with conventional solvent extraction (CSE), UAE showed a pronounced greater extraction yield and reduced extraction time effectively with a peak value at 30 min. The extraction yield was significantly influenced by temperature and the optimum condition was 30 °C. The extraction yield increased with increasing of solvent/material ratio until equilibrium was arrived at the optimal ratio of 3:1 (mL/g). The extraction yield increased first and then decreased with an increase in ultrasonic intensity. The extraction yield of UAE increased with the increase of duty cycle, whereas pulsed ultrasound with proper intervals was more efficient than continuous ultrasonication. The degradation via isomerisation of all-trans-lycopene under ultrasonic treatment was also observed with the formation of 9,13′-di-cis-, 9,13-di-cis-, 15-cis-, 13-cis- and 9-cis-lycopene isomers which were tentatively identified by HPLC-PAD.     

Comparison of ultrasound-assisted extraction with conventional extraction methods of oil and polyphenols from grape (Vitis vinifera L.) seeds

Ultrasound-assisted extraction (US) carried out at 20 KHz, 150 W for 30 min gave grape seed oil yield (14% w/w) similar to Soxhlet extraction (S) for 6 h. No significant differences for the major fatty acids was observed in oils extracted by S and US at 150 W. Instead, K₂₃₂ and K₂₆₈ of US- oils resulted lower than S-oil. From grape seeds differently defatted (S and US), polyphenols and their fractions were extracted by maceration for 12 h and by ultrasound-assisted extraction for 15 min. Sonication time was optimized after kinetics study on polyphenols extraction. Grape seed extracts obtained from seeds defatted by ultrasound (US) and then extracted by maceration resulted the highest in polyphenol concentration (105.20 mg GAE/g flour) and antioxidant activity (109 Eq αToc/g flour).     

Kinetic improvement of olive leaves’ bioactive compounds extraction by using power ultrasound in a wide temperature range

In this study, the effect of temperature and ultrasonic application on extraction kinetics of polyphenols from dried olive leaf was investigated. Conventional (CVE) and ultrasonic-assisted extraction (UAE) were performed at 10, 20, 30, 50 and 70 °C using water as solvent. Extracts were characterized by measuring the total phenolic content, the antioxidant capacity and the oleuropein content (HPLC–DAD/MS–MS). Moreover, Naik’s model was used to mathematically describe the extraction kinetics. The experimental results showed that phenolic extraction was faster in UAE (ultrasonic-assisted extraction) than in CVE (conventional extraction), being extraction kinetics satisfactorily described using Naik model (include VAR > 98%). Besides, the total phenolic content, the antioxidant capacity and the oleuropein content were significantly (p < 0.05) improved by increasing the temperature in both CVE and UAE. Oleuropein content reached 6.57 ± 0.18 being extracted approximately 88% in the first minute for UAE experiments.     

Ultrasound assisted enzyme catalyzed hydrolysis of waste cooking oil under solvent free condition

The present work demonstrates the hydrolysis of waste cooking oil (WCO) under solvent free condition using commercial available immobilized lipase (Novozyme 435) under the influence of ultrasound irradiation. The process parameters were optimized using a sequence of experimental protocol to evaluate the effects of temperature, molar ratios of substrates, enzyme loading, duty cycle and ultrasound intensity. It has been observed that ultrasound-assisted lipase-catalyzed hydrolysis of WCO would be a promising alternative for conventional methods. A maximum conversion of 75.19% was obtained at mild operating parameters: molar ratio of oil to water (buffer pH 7) 3:1, catalyst loading of 1.25% (w/w), lower ultrasound power 100 W (ultrasound intensity – 7356.68 W m⁻²), duty cycle 50% and temperature (50 °C) in a relatively short reaction time (2 h). The activation energy and thermodynamic study shows that the hydrolysis reaction is more feasible when ultrasound is combined with mechanical agitation as compared with the ultrasound alone and simple conventional stirring technique. Application of ultrasound considerably reduced the reaction time as compared to conventional reaction. The successive use of the catalyst for repetitive cycles under the optimum experimental conditions resulted in a loss of enzymatic activity and also minimized the product conversion.     

Comparisons between conventional,ultrasound-assisted and microwave-assisted methods for extraction of anthraquinones from Heterophyllaea pustulata Hook f. (Rubiaceae)

This work reports a comparative study about extraction methods used to obtain anthraquinones (AQs) from stems and leaves of Heterophyllae pustulata Hook (Rubiáceae). One of the conventional procedures used to extract these metabolites from a vegetable matrix is by successive Soxhlet extractions with solvents of increasing polarity: starting with hexane to eliminate chlorophylls and fatty components, following by benzene and finally ethyl acetate. However, this technique shows a low extraction yield of total AQs, and consumes large quantities of solvent and time. Ultrasound-assisted extraction (UAE) and microwave-assisted extraction (MAE) have been investigated as alternative methods to extract these compounds, using the same sequence of solvents. It was found that UAE increases the extraction yield of total AQs and reduces the time and amount of solvent used. Nevertheless, the combination UAE with benzene, plus MAE with ethyl acetate at a constant power of 900 W showed the best results. A higher yield of total AQs was obtained in less time and using the same amount of solvent that UAE. The optimal conditions for this latter procedure were UAE with benzene at 50 °C during 60 min, followed by MAE at 900 W during 15 min using ethyl acetate as extraction solvent.     

Optimization of ultrasonic-assisted extraction of pomegranate (Punica granatum L.) seed oil

The effectiveness of ultrasonic-assisted extraction (UAE) of pomegranate seed oil (PSO) was evaluated using a variety of solvents. Petroleum ether was the most effective for oil extraction, followed by n-hexane, ethyl acetate, diethyl ether, acetone, and isopropanol. Several variables, such as ultrasonic power, extraction temperature, extraction time, and the ratio of solvent volume and seed weight (S/S ratio) were studied for optimization using response surface methodology (RSM). The highest oil yield, 25.11% (w/w), was obtained using petroleum ether under optimal conditions for ultrasonic power, extraction temperature, extraction time, and S/S ratio at 140 W, 40 °C, 36 min, and 10 ml/g, respectively. The PSO yield extracted by UAE was significantly higher than by using Soxhlet extraction (SE; 20.50%) and supercritical fluid extraction (SFE; 15.72%). The fatty acid compositions were significantly different among the PSO extracted by Soxhlet extraction, SFE, and UAE, with punicic acid (>65%) being the most dominant using UAE.     

Effect of oil extraction assisted by ultrasound on the physicochemical properties and fatty acid profile of pumpkin seed oil (Cucurbita pepo)

The effects of amplitude and time of ultrasound-assisted extraction on the physicochemical properties and the fatty acid profile of pumpkin seed oil (Cucurbita pepo) were evaluated. Ultrasound time (5–30 min) and the response variables amplitude (25–100%), extraction yield, efficiency, oxidative stability in terms of the free fatty acids (FFA) of the plant design comprising two independent experiments variables, peroxide (PV), p-anisidine (AV), totox value (TV) and the fatty acid profile were evaluated. The results were analyzed by multiple linear regression. The time and amplitude showed significant differences (P < 0.05) for all variables. The highest yield of extraction was achieved at 5 min and amplitude of 62.5% (62%). However, the optimal ultrasound-assisted extraction conditions were as follows: ultrasound time of 26.34 min and amplitude of 89.02%. All extracts showed low FFA (2.75–4.93% oleic acid), PV (1.67–4.68 meq/kg), AV (1.94–3.69) and TV (6.25–12.55) values. The main fatty acids in all the extracts were oleic and linoleic acid. Therefore, ultrasound-assisted oil extraction had increased performance and reduced extraction time without affecting the oil quality.     

Ultrasound-assisted extraction of phenolics from wine lees: Modeling,optimization and stability of extracts during storage

The ultrasound-assisted extraction process of phenolics including anthocyanins from wine lees was modeled and optimized in this research. An ultrasound bath system with the frequency of 40 kHz was used and the acoustic energy density during extraction was identified to 48 W/L. The effects of extraction time, extraction temperature, solvent-to-solid ratio and the solvent composition on the extraction yields of total phenolics and total anthocyanins were taken into account. The extraction process was simulated and optimized by means of artificial neural network (ANN) and genetic algorithm (GA). The constructed ANN models were accurate to predict the extraction yields of both total phenolics and total anthocyanins according to the statistical analysis. Meanwhile, the input space of the ANN models was optimized by GA, so as to maximize the extraction yields. Under the optimal conditions, the experimental yields of total phenolics and total anthocyanins were 58.76 and 6.69 mg/g, respectively, which agreed with the predicted values. Furthermore, more amounts of total phenolics and total anthocyanins were extracted by ultrasound at the optimal conditions than by conventional maceration.On the other hand, the stability of phenolics in the liquid extracts obtained from ultrasound-assisted extraction during storage was evaluated. After 30-day storage, the total phenolic contents in extracts stored at 4 °C and 20 °C decreased by 12.5% and 12.1%, respectively. Moreover, anthocyanins were more stable at 4 °C while tartaric esters and flavonols exhibited a better stability at 20 °C. Overall, the loss of phenolics during storage found in this study could be acceptable.     

Effect of acoustic frequency and power density on the aqueous ultrasonic-assisted extraction of grape pomace (Vitis vinifera L.) – A response surface approach

Aqueous ultrasound-assisted extraction (UAE) of grape pomace was investigated by Response Surface Methodology (RSM) to evaluate the effect of acoustic frequency (40, 80, 120 kHz), ultrasonic power density (50, 100, 150 W/L) and extraction time (5, 15, 25 min) on total phenolics, total flavonols and antioxidant capacity. All the process variables showed a significant effect on the aqueous UAE of grape pomace (p < 0.05). The Box–Behnken Design (BBD) generated satisfactory mathematical models which accurately explain the behavior of the system; allowing to predict both the extraction yield of phenolic and flavonol compounds, and also the antioxidant capacity of the grape pomace extracts. The optimal UAE conditions for all response factors were a frequency of 40 kHz, a power density of 150 W/L and 25 min of extraction time. Under these conditions, the aqueous UAE would achieve a maximum of 32.31 mg GA/100 g fw for total phenolics and 2.04 mg quercetin/100 g fw for total flavonols. Regarding the antioxidant capacity, the maximum predicted values were 53.47 and 43.66 mg Trolox/100 g fw for CUPRAC and FRAP assays, respectively. When comparing with organic UAE, in the present research, from 12% to 38% of total phenolic bibliographic values were obtained, but using only water as the extraction solvent, and applying lower temperatures and shorter extraction times. To the best of the authors’ knowledge, no studies specifically addressing the optimization of both acoustic frequency and power density during aqueous-UAE of plant materials have been previously published.     

A possible general mechanism for ultrasound-assisted extraction (UAE) suggested from the results of UAE of chlorogenic acid from Cynara scolymus L. (artichoke) leaves

The use of ultrasound-assisted extraction (UAE) for the extraction of chlorogenic acid (CA) from Cynara scolymus L., (artichoke) leaves using 80% methanol at room temperature over 15 min gave a significant increase in yield (up to a 50%) compared with maceration at room temperature and close to that obtained by boiling over the same time period. A note of caution is introduced when comparing UAE with Soxhlet extraction because, in the latter case, the liquid entering the Soxhlet extractor is more concentrated in methanol (nearly 100%) that the solvent in the reservoir (80% methanol) due to fractionation during distillation. The mechanism of UAE is discussed in terms of the effects of cavitation on the swelling index, solvent diffusion and the removal of a stagnant layer of solvent surrounding the plant material.     

Optimisation of ultrasound assisted extraction of phenolic compounds from Sparganii rhizoma with response surface methodology

The present study reports on the extraction of phenolic compounds from sparganii rhizome. Box–Behnken Design (BBD), a widely used form of response surface methodology (RSM), was used to investigate the effect of process variables on the ultrasound-assisted extraction (UAE). Three independent variables including ethanol concentration (%), extraction time (min) and solvent-to-material ratio (mL/g) were studied. The results showed that the optimal UAE condition was obtained with an ethanol concentration of 75.3%, an extraction time of 40 min and a solvent-to-material ratio of 19.21 mL/g for total phenols, and an ethanol concentration of 80%, an extraction time of 33.54 min and solvent-to-material ratio of 22.72 mL/g for combination of ρ-hydroxybenzaldehyde, ρ-coumaric acid, vanillic acid, ferulic acid, rutin and kaempferol. The experimental values under optimal conditions were in good consistent with the predicted values, which suggested UAE is more efficient process as compared to solvent extraction.     

Optimization of ultrasonic-assisted extraction (UAE) of betulin from white birch bark using response surface methodology

Betulin is an abundant naturally occurring triterpene, which makes it a potentially important raw material for a precursor of biologically active compounds. The objective of the current study was to determine the optimum UAE conditions for betulin from B. papyfera bark. The optimum conditions were evaluated with fractional factorial design and optimized using response surface methodology. High yields of betulin were observed from white birch bark by UAE technology. The solvent concentration and the ratio of material to solvent were the most significant parameters on betulin extraction as evaluated through FFD. The extraction conditions were further investigated with central composite design. The fitted second-order model revealed that the optimal conditions consisted of 98% ethonal concentration, 1:42 the ratio of white birch bark to solvent, extraction temperature 50 °C, ultrasonic frequency 5 kHz and extraction time 3 h. Under the optimized condition, the maximum productivity of betulin predicted is 23.17%. The extraction productivity and purity of betulin under the optimized extraction conditions were great higher than that of the non-optimized condition. The present study demonstrates that ultrasound is a great efficiency tool for the fast extraction of betulin from white birch bark.     

Optimization of ultrasonic cell grinder extraction of anthocyanins from blueberry using response surface methodology

Ultrasonic cell grinder extraction (UCGE), using water as the solvent, was firstly applied to extract anthocyanins from blueberry. Extraction yield was related with four variables, including ratio of solution to solid, extraction power, buffer time, and extraction time. On the basis of response surface methodology (RSM), the optimal conditions were determined to be the ratio of solution to solid as 25:1 (mL/g), the extraction power as 1500 W, the buffer time as 3.0 s, and the extraction time as 40 min. The experimental yield of anthocyanins using UCGE was 2.89 mg/g higher than that of conventional ultrasound-assisted extraction (CUAE). This study indicated that UCGE was an innovative, efficient, and environment friendly method in ultrasonic extraction fields, and had a potential to effectively extract other bioactive constituents.