简易模板剂法制备多级介孔TiO2微球及其在染料敏化太阳能电池中的性能

采用模板剂法一步合成分级结构的介孔TiO₂微球, 考察了烷基胺类模板剂中烷基链长度对介孔TiO₂微球合成及性能影响. 将其应用于染料敏化太阳能电池的光阳极半导体薄膜中, 得到了9.5%-10.1%的高能量转换效率. X射线衍射(XRD)、物理吸附仪(BET)、扫描电镜(SEM)等的分析结果表明: 分级结构介孔TiO₂微球的晶相为纯锐钛矿型; 介孔TiO₂微球表面粗糙, 的纳米粒子堆积形成, 使微球具有介孔性质和较适宜的比表面积. 介孔TiO₂微球堆积形成了利于物质扩散的通道并具有良好的光散射效果; 同时微球介孔粗糙表面保证了染料的大量吸附, 从而提高了电池的光电流. 通过电化学阻抗分析结果验证了分等级结构介孔TiO₂微球光阳极有利于电解液的传输和物质扩散的优异性能.     

Study on the fabrication and photovoltaic property of TiO2 mesoporous microspheres

Titanium dioxide mesoporous microspheres with high surface area was successfully prepared by a facile one-step hydrothermal approach using polyethylene glycol (PEG, MW 200) as the soft template. Study shows that ∼15 nm TiO₂ nanoparticles was assembled into ∼1.1 μm mesoporous microspheres. The Brunauer-Emmett-Teller surface area of TiO₂ microsphere is up to 137 m²/g. TiO₂ mesoporous microspheres were fabricated onto the surface of fluorine-doped tin oxide glass and used as the photoanode of dye-sensitized solar cells, which exhibits an open circuit photovoltage of 0.80 V and an overall conversion efficiency of 6.6%. Owing to the enhanced dye loading and light-harvesting efficiency, a 26% improvement in the overall conversion efficiency was achieved when compared with the commercial Degussa P₂₅ nanoparticles.     

Solar photocatalytic activities of porous Nb-doped TiO2 microspheres prepared by ultrasonic spray pyrolysis

Ultrasonic spray pyrolysis method was used to prepare Nb-doped TiO₂ porous microspheres with an average diameter of 500 nm for solar photocatalytic applications. The effect of Nb-doping on morphology, structure, surface area, as well as spectral absorption properties of TiO₂ microspheres was investigated with SEM, TEM, XRD, Raman spectra, BET, and UV-Vis absorption spectra. The Nb-doping decreased the grain size of TiO₂ porous microsphere, and influenced its surface area and pore size distribution dependent on the doping concentration, but changed negligibly the morphology and size of TiO₂ microspheres. Moreover, the Nb-doping was observed to extend the spectral absorption of TiO₂ into visible spectrum, and the absorption onset was red-shifted for about 88 nm at a doping level of 5% compared to pristine TiO₂ microspheres. Under solar or visible irradiation, Nb-doped TiO₂ microspheres showed higher photocatalytic activity for methylene blue degradation compared with TiO₂ microspheres, which could be ascribed to the extended light absorption range and the suppression of electron-hole pair recombination.     

TiO2微球的合成及其作为散射层在量子点敏化太阳能电池中的应用

以十六烷基三甲基溴化铵（CTAB）为模板剂,通过TiCl₄在乙醇水溶液中的直接水解,制备了介孔TiO₂微球. X射线衍射（XRD）结果表明所制备的微球晶型为金红石,扫描电镜（SEM）结果显示微球的直径大约为700 nm,由粒径约为16 nm的小颗粒堆积而成. 通过刮涂法制备了在TiO₂小颗粒层上涂覆有作为散射层的TiO₂微球和未涂覆微球的薄膜. 并通过化学浴沉积（CBD）的方法在膜上生长CdS/CdSe量子点,得到了量子点敏化太阳能电池（QDSCs）. 紫外吸收和漫反射结果表明,这种微球结构有利于量子点的沉积,具有较强的光散射作用,有效地增加了光线的收集,从而提高了电池的光电流,最终得到了4.5%的光电转换效率,比不加散射层的电池的效率高27.7%,也比利用传统散射层（由20 nm TiO₂ 小颗粒和400 nm TiO₂ 固体颗粒组成）的电池效率高10.2%. 我们把电池效率的提升归因于较强的光散射作用和较长的电子寿命.     

Novel sol–gel synthesis of N-doped TiO<Subscript>2</Subscript> hollow spheres with high photocatalytic activity under visible light

Novel ammonia and triethanolamine assisted sol–gel synthesis method was developed to fabricate the N-doped TiO₂ hollow spheres. The prepared hollow spheres were in submicron size and had good morphology and high specific surface area. Polystyrene (PS) latexes in size of 470 nm were used as the templates to fabricate PS/TiO₂ core–shell spheres. Here ammonia and triethanolamine was first employed together to control the sol–gel process. The N-doped TiO₂ hollow spheres were got after calcinations of the core–shell spheres by using triethanolamine as N source, and the amount of doped N could be easily adjusted by changing the amount of triethanolamine. The hollow spheres had distinct visible light response, and the optical response shifted more to the visible region as the amount of doped N increases. The photodegradation of methylene blue expressed the high photocatalytic activity of the N-doped TiO₂ hollow spheres under visible light.     

Ultrasonic Preparation of Hierarchical Graphene‐Oxide/TiO2 Composite Microspheres for Efficient Photocatalytic Hydrogen Production

Hierarchical graphene oxide (GO)‐TiO₂ composite microspheres with different GO/TiO₂ mass ratios were successfully prepared by mixing GO and TiO₂ microspheres under ultrasonic conditions. Ultrasonication helped the GO and TiO₂ microsphere to uniformly mix on the microscale. The results showed that the GO‐TiO₂ composites that were prepared by ultrasonic mixing exhibited significantly higher hydrogen‐evolution rates than those that were synthesized by simple mechanical grinding, owing to synergetic effects, including enhanced light absorption and scattering, as well as improved interfacial charge transfer because of the excellent contact between the GO sheets and TiO₂ microspheres. In addition, GO‐TiO₂‐3 (3 wt. % GO) showed the highest hydrogen‐generation rate (305.6 μmol h^?), which was about 13 and 3.3‐times higher than those of TiO₂ microsphere and GO‐P25 (with 3 wt. % GO), respectively. Finally, a tentative mechanism for hydrogen production is proposed and supported by photoluminescence and transient photocurrent measurements. This work highlights the potential applications of GO‐TiO₂ composite microspheres in the field of clean‐energy production.     

TiO2 Nanospheres: A Facile Size‐Tunable Synthesis and Effective Light‐Harvesting Layer for Dye‐Sensitized Solar Cells

A facile route to synthesize amorphous TiO₂ nanospheres by a controlled oxidation and hydrolysis process without any structure‐directing agents or templates is presented. The size of the amorphous TiO₂ nanospheres can be easily turned from 20 to 1500 nm by adjusting either the Ti species or ethanol content in the reaction solution. The phase structure of nanospheres can be controlled by hydrothermal treatment. The TiO₂ nanospheres show excellent size‐dependent light‐scattering effects and can be structured into a light‐harvesting layer for dye‐sensitized solar cells with a quite high power conversion efficiency of 9.25 %.     

锌离子掺杂的二氧化钛介孔空心微球的制备及光催化性能

以二氧化硅为模板,钛酸四丁酯（TBOT）为钛源,硝酸锌为锌源,采用溶胶凝胶法制备了锌离子掺杂的介孔二氧化钛空心微球。采用X射线衍射（XRD）、比表面积（BET）、透射电镜（TEM）、扫描电镜（SEM）和X射线光电子能谱（XPS）等技术对样品进行表征,以亚甲基蓝（MB）的光催化降解为目标反应评价其光催化活性。结果表明,去核之后的复合微球为空心微球,壁厚为20nm左右。钛酸四丁酯溶液的滴加时间对微球的形貌影响较大,当滴加时间大于15min时,可以得到结构清晰的空心微球。用氢氧化钠溶液去除二氧化硅核,反应90min,二氧化硅可以被完全去除。X射线衍射表明,实验得到的掺杂锌离子的空心微球和没有掺杂锌离子的空心微球都是锐钛矿。当锌离子的摩尔分数为0.3%时,二氧化钛空心微球的晶粒尺寸最小,比表面积最大,催化亚甲基蓝降解的效率最高。     

锌离子掺杂的二氧化钛介孔空心微球的制备及光催化性能

以二氧化硅为模板,钛酸四丁酯(TBOT)为钛源,硝酸锌为锌源,采用溶胶凝胶法制备了锌离子掺杂的介孔二氧化钛空心微球。采用X射线衍射(XRD)、比表面积(BET)、透射电镜(TEM)、扫描电镜(SEM)和X射线光电子能谱(XPS)等技术对样品进行表征,以亚甲基蓝(MB)的光催化降解为目标反应评价其光催化活性。结果表明,去核之后的复合微球为空心微球,壁厚为20 nm左右。钛酸四丁酯溶液的滴加时间对微球的形貌影响较大,当滴加时间大于15 min时,可以得到结构清晰的空心微球。用氢氧化钠溶液去除二氧化硅核,反应90 min,二氧化硅可以被完全去除。X射线衍射表明,实验得到的掺杂锌离子的空心微球和没有掺杂锌离子的空心微球都是锐钛矿。当锌离子的摩尔分数为0.3%时,二氧化钛空心微球的晶粒尺寸最小,比表面积最大,催化亚甲基蓝降解的效率最高。     

Synthesis of bimodal porous structured TiO2 microsphere with high photocatalytic activity for water treatment

In this work bimodal structured titanium dioxide (TiO₂) microsphere has been prepared from commercial TiO₂ powder and nano-sized titania gel via sol–gel spray-coating technique. Crystallization and transformation behavior of titania gel were investigated. The results revealed that the crystallization and transformation of anatase particles were substantially affected by the concentration of solvent and calcination temperature. Anatase crystallite size of 10 nm was obtained at mole ratio of solvent/precursor 50/1 and calcination temperature of 450 °C. The prepared nano-sized titania gel was embedded within the core (commercial TiO₂, P25) during the spraying process. The prepared TiO₂ microsphere was characterized using X-ray diffractometer (XRD), scanning electron microscope (SEM), field emission electron microscope (FESEM) and micropore analysis. The photocatalytic activity was monitored by following the degradation of phenol with activity benchmarked against commercial P25 (Degussa). The increase of photocatalytic activity of TiO₂ microsphere was attributed to the nano-sized anatase crystallite which has been incorporated into the TiO₂ microsphere.     

接枝共聚法制备二氧化钛/聚（苯乙烯-二乙烯基苯）复合微球

本文以KH560、苯乙烯、马来酸酐为连接组分,将二氧化钛接枝到聚（苯乙烯-二乙烯基苯）微球的表面,成功制备了无孔和多孔纳米复合微球。研究了硅烷偶联剂（KH560）和苯乙烯对二氧化钛在无孔微球表面的分散性和接枝数量以及支撑微球的多孔性质对接枝到微球内部的二氧化钛数量的影响。结果表明,KH560和苯乙烯能够提高二氧化钛在微球表面的分散性和稳定性,使二氧化钛以30-80nm的粒径接枝在微球表面。苯乙烯又能使二氧化钛在无孔微球表面的接枝数量从10.4%增大到20.4%。平均孔径为136nm的多孔微球为支撑微球得到的复合粒子中二氧化钛最高接枝量可达26%,明显高于无孔微球和平均孔径为31nm的多孔微球。     

Fabrication and performance of nanoporous TiO2/SnO2 electrodes with a half hollow sphere structure for dye sensitized solar cells

The incorporation of nano-crystalline semiconductors with novel kinds of ordered microstructure is a very important area of research in the field of dye sensitized solar cells. A sol–gel method involving hydrolysis of titanium isopropoxide was used to form TiO₂ nanoparticles on the surface of SiO₂ spheres. In this process, 1, 5, or 10 wt% of SnCl₂.2H₂O was added to the sol–gel solution. To prepare TiO₂/SnO₂ nanoparticles with a half hollow sphere structure, SiO₂ was removed with NaOH solution. The crystal phase, crystal shape, and surface properties of the metal oxide nanocrystals were studied by x-ray diffraction and scanning electron microscopy. The photovoltaic performance of the TiO₂/SnO₂ nanoparticles with half hollow sphere structures was measured. The dye sensitized solar cell using nanoporous TiO₂ as electrode materials exhibits an overall conversion efficiency of 7.36% with a light intensity of 100 mW/cm². The short circuit photocurrent (I_sc), open circuit photovoltage (V_oc), and conversion efficiency (η) of these solar cells were improved over conventional materials.     

Reversible addition‐fragmentation chain transfer polymerization of a typical hydrophobic monomer of styrene within microreactor of shell‐corona hollow microspheres suspending in water

Reversible addition‐fragmentation chain transfer (RAFT) polymerization of a typical hydrophobic monomer of styrene within microreactor of shell‐corona hollow microspheres of poly(styrene‐co‐methacrylic acid) suspending in water is studied. The shell‐corona hollow microspheres contain a hydrophilic corona of poly(methacrylic acid) (PMAA) and a cross‐linked polystyrene shell, which can suspend in water because of the hydrophilic corona of PMAA. The size of the shell‐corona hollow microspheres is about 289 nm and the extent of the microcavity of the hollow microsphere is 154 nm. These shell‐corona hollow microspheres can act as microreactor, within which the typical hydrophobic monomer of styrene, the RAFT agent of S‐benzyl dithiobenzoate and the initiator of 2,2′‐azobisisobutyronitrile can be encapsulated and RAFT polymerization of styrene takes place in well controlled manner in water. It is found that the resultant polymer of polystyrene has a competitively low polydispersity index and its number‐average molecular weight linearly increases with monomer conversion. The method is believed to be a new strategy of RAFT polymerization of hydrophobic monomer in aqueous solution. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

TiO2@CdS core–shell nanorods films: Fabrication and dramatically enhanced photoelectrochemical properties

In this paper, we prepared TiO₂@CdS core–shell nanorods films electrodes using a simple and low-cost chemical bath deposition method. The core–shell nanorods films electrodes were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and UV–vis spectrometry techniques. After applying these TiO₂@CdS core–shell nanorods electrodes in photovoltaic cells, we found that the photocurrent was dramatically enhanced, comparing with those of bare TiO₂ nanorods and CdS films electrodes. Moreover, TiO₂@CdS core–shell nanorods film electrode showed better cell performance than CdS nanoparticles deposited TiO₂ nanoparticles (P25) film electrode. A photocurrent of 1.31 mA/cm², a fill factor of 0.43, an open circuit photovoltage of 0.44 V, and a conversion efficiency of 0.8% were obtained under an illumination of 32 mW/cm², when the CdS nanoparticles deposited on TiO₂ nanorods film for about 20 min. The maximum quantum efficiency of 5.0% was obtained at an incident wavelength of 500 nm. We believe that TiO₂@CdS core–shell heterostructured nanorods are excellent candidates for studying some fundamental aspects on charge separation and transfer in the fields of photovoltaic cells and photocatalysis.     

改进型溶胶-凝胶法制备粒径可调高染料吸附量TiO2微球及其在染敏电池光散射层中的应用

利用改进型的溶胶-凝胶法, 制得了由锐钛矿相纳米颗粒组成的TiO₂多孔微纳小球。通过调节前驱物浓度, 合成出粒径可控的尺寸分别为100, 175, 225, 475 nm的TiO₂微纳小球, 并通过电泳沉积法将合成出的小球作为光散射层引入到染料敏化太阳电池(DSSC)中。由于这种微纳小球在具备良好的光散射性能的同时也具备较高的染料吸附量, 因此相较于基于纳米颗粒的单层结构的DSSC拥有更高的光电转换效率。通过比较分析, 粒径尺寸为475 nm的微球作为光散射层的DSSC光电转换效率可以达到6.3%, 较之于基于纳米颗粒的DSSC提高了30%。     

改进型溶胶-凝胶法制备粒径可调高染料吸附量TiO2微球及其在染敏电池光散射层中的应用

利用改进型的溶胶-凝胶法,制得了由锐钛矿相纳米颗粒组成的TiO2多孔微纳小球。通过调节前驱物浓度,合成出粒径可控的尺寸分别为100,175,225,475 nm的TiO2微纳小球,并通过电泳沉积法将合成出的小球作为光散射层引入到染料敏化太阳电池(DSSC)中。由于这种微纳小球在具备良好的光散射性能的同时也具备较高的染料吸附量,因此相较于基于纳米颗粒的单层结构的DSSC拥有更高的光电转换效率。通过比较分析,粒径尺寸为475 nm的微球作为光散射层的DSSC光电转换效率可以达到6.3%,较之于基于纳米颗粒的DSSC提高了30%。     

Porous α-Fe2O3 hollow microspheres and their application for acetone sensor

Porous α-Fe₂O₃ hollow microspheres were synthesized through a simple and efficient carbon sphere template method. The samples were characterized by X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy, transmission electron microscopy and N₂ adsorption-desorption. Structural characterization indicated that as-prepared α-Fe₂O₃ hollow microspheres had porous structure with around 200 nm in diameter and thin shell about 10 nm thick. The average pore size and Brunauer-Emmett-Teller specific surface area of α-Fe₂O₃ hollow microspheres were 6.5 nm and 111.6 m²/g, respectively. The gas sensing behavior investigation showed that as-synthesized α-Fe₂O₃ hollow microspheres exhibited very good gas sensing property to acetone vapor.     

Three‐Dimensional Ordered Assembly of Thin‐Shell Au/TiO2 Hollow Nanospheres for Enhanced Visible‐Light‐Driven Photocatalysis

An Au/TiO₂ nanostructure was constructed to obtain a highly efficient visible‐light‐driven photocatalyst. The design was based on a three‐dimensional ordered assembly of thin‐shell Au/TiO₂ hollow nanospheres (Au/TiO₂‐3 DHNSs). The designed photocatalysts exhibit not only a very high surface area but also photonic behavior and multiple light scattering, which significantly enhances visible‐light absorption. Thus Au/TiO₂‐3 DHNSs exhibit a visible‐light‐driven photocatalytic activity that is several times higher than conventional Au/TiO₂ nanopowders.     

中空Ta2O5/TiO2复合光催化剂的可控氧化制备及性能

以钛粉、钽粉为原料,炭黑作为反应性模板,通过熔盐法在炭黑表面原位生长了TaTiC₂纳米碳化物涂层,并以所得TaTiC₂/C复合物为碳化物前驱体,再经可控氧化制备出中空Ta₂O₅/TiO₂复合光催化剂。采用X射线粉末衍射（XRD）、扫描电子显微镜（SEM）、透射电子显微镜（TEM）、紫外-可见（UV-Vis）漫反射（DRS）及N₂物理吸附等手段对所制备的光催化剂进行形貌、显微结构及孔结构表征。以高压汞灯为紫外光源,以亚甲基蓝为目标降解物,通过光催化降解实验评价中空Ta₂O₅/TiO₂复合光催化剂的光催化活性。结果表明,熔盐法生长碳化物涂层厚度均匀（20~30 nm）,碳化物主要以TaTiC₂晶相存在且具有纳米级的颗粒尺寸。中空Ta₂O₅/TiO₂复合光催化剂同时具有200 nm左右的中空大孔结构及壳层10 nm左右的介孔结构。中空大孔和介孔的存在提高了所制备催化剂对亚甲基蓝的吸附能力。此外,TiO₂与Ta₂O₅通过电子能带结构的耦合,有效提高了光生电子和空穴的分离效率,从而显著提高了光催化活性。n_Ti∶n_Ta=2.5∶1.5时,相应的中空Ta₂O₅/TiO₂复合光催化剂表现出最佳的光催化活性,对亚甲基蓝的紫外光催化降解率高达97%。     

中空Ta_2O_5/TiO_2复合光催化剂的可控氧化制备及性能

以钛粉、钽粉为原料,炭黑作为反应性模板,通过熔盐法在炭黑表面原位生长了TaTiC_2纳米碳化物涂层,并以所得TaTiC_2/C复合物为碳化物前驱体,再经可控氧化制备出中空Ta_2O_5/TiO_2复合光催化剂。采用X射线粉末衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、紫外-可见(UV-Vis)漫反射(DRS)及N2物理吸附等手段对所制备的光催化剂进行形貌、显微结构及孔结构表征。以高压汞灯为紫外光源,以亚甲基蓝为目标降解物,通过光催化降解实验评价中空Ta_2O_5/TiO_2复合光催化剂的光催化活性。结果表明,熔盐法生长碳化物涂层厚度均匀(20~30 nm),碳化物主要以TaTiC_2晶相存在且具有纳米级的颗粒尺寸。中空Ta_2O_5/TiO_2复合光催化剂同时具有200 nm左右的中空大孔结构及壳层10 nm左右的介孔结构。中空大孔和介孔的存在提高了所制备催化剂对亚甲基蓝的吸附能力。此外,TiO_2与Ta2O5通过电子能带结构的耦合,有效提高了光生电子和空穴的分离效率,从而显著提高了光催化活性。nTi∶nTa=2.5∶1.5时,相应的中空Ta_2O_5/TiO_2复合光催化剂表现出最佳的光催化活性,对亚甲基蓝的紫外光催化降解率高达97%。