Determination of selenium in soils with square-wave cathodic stripping voltammetry

A new voltammetric method is elaborated for the trace determination of selenium in soils. The use of the square-wave cathodic stripping voltammetry in the determination step efficiently eliminates the interference of electroactive components. The detection limit is 0.75 g/l.     

Determinationation of kanamycin by square-wave cathodic adsorptive stripping voltammetry

A square-wave cathodic adsorptive stripping voltametric (SWCASV) method for the determination of kanamycin was developed on a thin-film mercury electrode (TFME). The optimal working conditions for the application of the method were found to be pH 8.0, provided by a Britton-Robinson (B.R.) buffer, and an adsorption potential of +0.30 V during 300 s. The equilibration time was applied during 10 s, and potential scans were performed at a scan rate of 40 mV/s, with a square-wave frequency of 100 Hz. The measuring-system response was linear over the kanamycin concentration range from 1.2 × 10⁻⁹ to 5.0 × 10⁻⁸ M and the detection limit achieved was 4.8 × 10⁻¹⁰ M. The relative error and relative standard deviation obtained were 1.20 and 4.67%, respectively. The voltammetric procedure was applied successfully to give a rapid and precise assay of kanamycin in kanamycin sulfate injection form. Published in Elektrokhimiya in Russian, 2008, Vol. 44, No. 12, pp. 1433–1437. The text was submitted by author in English     

Direct determination of molybdenum in seawater by adsorption cathodic stripping square-wave voltammetry

A reliable and very sensitive procedure for the determination of trace levels of molybdenum in seawater is proposed. The complex of molybdenum with 8-hydroxyquinoline (Oxine) is analyzed by cathodic stripping square-wave voltammetry based on the adsorption collection onto a hanging mercury drop electrode (HMDE). This procedure of molybdenum determination was found to be more favorable than differential pulse cathodic stripping voltammetry because of inherently faster scan rate and much better linearity obtained through the one-peak (instead of one-of-two peaks) calibration. The variation of polarographic peak and peak current with a pH, adsorption time, adsorption potential, and some instrumental parameters such as scan rate and pulse height were optimized. The alteration of polarographic wave and its likely mechanism are also discussed. The relationship between peak current and molybdenum concentration is linear up to 150 mug l(-1). Under the optimal analytical conditions, the determination limit of 0.5 mug l(-1) Mo was reached after 60 s of the stirred collection. The estimated detection limit is better than 0.1 mug l(-1) of Mo. The applicability of this method to analysis of seawater was assessed by the determination of molybdenum in two certified reference seawater samples (CASS-2 and NASS-2) and the comparison of the analytical results for real seawater samples (study on a vertical distribution of Mo in the seawater column) with the results obtained by Zeeman-corrected electrothermal atomization atomic absorption spectrometry (Zeeman ETAAS). A good agreement between two used methods of molybdenum determination was obtained.     

Determination of chitosan by cathodic stripping voltammetry.

A sensitive method for the determination of chitosan (CTS) by cathodic stripping voltammetry is presented. The method exploits a pair of oxidation-reduction peaks of CTS at -0.62 V (vs. SCE) and -0.54 V (vs. SCE), and an enhancement of the peak current of CTS observed in a 0.05 mol l(-1) potassium hydrogenphthalate buffer solution (pH 2.5). The peak current is linear with the concentration of CTS from 5.0 x 10(-7) to 1.5 x 10(-5) g ml(-1), and the detection limit is 1.0 x 10(-7) g ml(-1). We studied the characteristics and the mechanism of the electrode reaction, which proved that this process was diffusion controlled. This method was applied to determine the content of CTS in real samples with satisfactory results.     

Assay of dipyridamole in human serum using cathodic adsorptive square-wave stripping voltammetry

A rapid and sensitive square-wave voltammetric procedure was optimized for the determination of dipyridamole after its adsorption preconcentration onto a hanging mercury drop electrode. The peak current of the first of the two peaks developed for this drug in Britton-Robinson buffer at pH 8.0 has been considered for the present analytical study. An accumulation potential of -1.0 V versus Ag/AgCl/KCl(s), pulse amplitude a =100 mV, scan increment Delta E =10 mV, and frequency f =120 Hz were the optimal experimental parameters. Dipyridamole can be determined in the concentration range of 9.0 x 10(-9) to 5.0 x 10(-6) M using accumulation times of 30-300 s. A detection limit of 4.0 x 10(-11) M was achieved after a 300 s accumulation time. Applicability to serum samples was illustrated. The average recoveries for dipyridamole spiked to serum at 0.25-4.50 micro g ml(-1) were 96.0-102.0%, and the higher standard deviation was 2.9%. A detection limit of 0.06 micro g mL(-1) of serum was obtained.     

Determination of the pesticide Chlorpyrifos by cathodic adsorptive stripping voltammetry

The adsorption behavior and differential pulse cathodic adsorptive stripping voltammetry of the pesticide Chlorpyrifos (CP) were investigated at the hanging mercury drop electrode (HMDE). The pesticide was accumulated at the HMDE and a well-defined stripping peak was obtained at –1.2 V vs Ag/AgCl electrode at pH 7.50. A voltammetric procedure was developed for the trace determination of Chlorpyrifos using differential pulse cathodic adsorptive stripping voltammetry (DP-CASV). The optimum working conditions for the determination of the compound were established. The peak current was linear over the concentration range 9.90 × 10^–8– 5.96 × 10^–7 mol/L of Chlorpyrifos. The influence of diverse ions and some other pesticides was investigated. The analysis of Chlorpyrifos in commercial formulations and treated waste water was carried out satisfactorily     

Determination of abscisic acid by cathodic stripping square wave voltammetry

In this paper a study is accomplished on behavior in a mercury electrode, of the phytohormone abscisic acid and of the conditions of accumulation in a HMDE. A mechanism is proposed of reduction based on its electrochemical behavior and proving the product of the reduction through mass spectrometry of bulks. A method is proposed for the determination of Abscisic acid (ABA) with a quantification limit of 58 ng ml(-1). The procedure is applied wing determination of ABA in pears through the combination of high performance liquid chromatography (HPLC) with electrochemical quantification.     

Determination of pyrithione in natural waters by cathodic stripping voltammetry

A method was developed to determine the biocide pyrithione in natural waters. The method is based on cathodic stripping voltammetry (CSV) in the presence of Triton-X-100, which is used to separate the peak from interfering thiol compounds. Optimised conditions include a Triton-X-100 concentration of 4 ppm and a pH adjusted to 9 using ammonia buffer. The adsorption potential for pyrithione was −0.10 V and the peak occurred at −0.2 to −0.3 V. Detection was by differential-pulse CSV. The detection limit in UV-digested seawater was 1.5 nM for a deposition time of 60 s. In principle, this limit of detection could be lowered by extending the adsorption time, but in practice this may not be possible due to interferences by other organic compounds (surfactants and thiol compounds) in natural waters.     

Determination of the pesticide Chlorpyrifos by cathodic adsorptive stripping voltammetry

The adsorption behavior and differential pulse cathodic adsorptive stripping voltammetry of the pesticide Chlorpyrifos (CP) were investigated at the hanging mercury drop electrode (HMDE). The pesticide was accumulated at the HMDE and a well-defined stripping peak was obtained at –1.2 V vs Ag/AgCl electrode at pH 7.50. A voltammetric procedure was developed for the trace determination of Chlorpyrifos using differential pulse cathodic adsorptive stripping voltammetry (DP-CASV). The optimum working conditions for the determination of the compound were established. The peak current was linear over the concentration range 9.90 × 10^–8– 5.96 × 10^–7 mol/L of Chlorpyrifos. The influence of diverse ions and some other pesticides was investigated. The analysis of Chlorpyrifos in commercial formulations and treated waste water was carried out satisfactorily Received: 10 July 1997 / Revised: 1 April 1998 / Accepted: 6 April 1998     

Theoretical and experimental study of the catalytic cathodic stripping square-wave voltammetry of chromium species

The electrocatalytic mechanism of Cr(III) reduction in the presence of diethylenetriaminepentaacetic acid (DTPA) and nitrate ions is studied theoretically and experimentally by using stripping square-wave voltammetry (SWV). Experimental curves are in excellent agreement with theoretical profiles corresponding to a catalytic reaction of second kind. This type of mechanism is equivalent to a CE mechanism, where the chemical reaction produces the electroactive species. Accordingly, the reaction of Cr(III)–H₂O–DTPA and \( {\mathrm{NO}}_3^{-} \) would produce the electroactive species Cr(III)–NO₃–DTPA and this last species would release \( {\mathrm{NO}}_2^{-} \) to the solution during the electrochemical step. In this regard, the complex of Cr(III)–DTPA would work as the catalyzer that allows the reduction of \( {\mathrm{NO}}_3^{-} \) to \( {\mathrm{NO}}_2^{-} \). Furthermore, it was found that the electrochemical reaction is quite irreversible, with a constant of k _s?=?9.4?×?10^?5 cm s^?1, while the constant for the chemical step has been estimated to be k _chem?=?1.3?×?10⁴ s^?1. Considering that the equilibrium constant is K?=?0.01, it is possible to estimate the kinetic constants of the chemical reaction as k ₁?=?1?×?10² s^?1 and k _?1?=?1.29?×?10⁴ s^?1. These values of k ₁ and k _?1 indicate that the exchange of water molecules by nitrate is fast and that the equilibrium favors the complex with water. Also, a value for the formal potential E°’?≈??1.1 V was obtained. The model used for simulating experimental curves does not consider the adsorption of reactants yet. Accordingly, weak adsorption of reagents should be expected.     

Determination of selenium in sea water by adsorptive cathodic stripping voltammetry

A procedure is presented for determining Se(IV) and total dissolved Se in sea water using cathodic stripping voltammetry in the presence of added copper. Experiments using cyclic voltammetry indicate that the preconcentration step consists in adsorption of a Cu(I)₂Se complex species on the hanging mercury drop electrode. The optimized analytical conditions include a copper concentration of 40 μM and a solution pH of 1.6. Differential pulse modulation is used. Interference caused by organic surface-active substances present in natural waters in eliminated by UV photolysis of the sample. Cadmium interferes with the determination of Se only when present at a concentration 100 times higher than normal. UV photolysis at pH ≈ 8 is used to convert Se(VI), which is the electroactive species. The response is linear for Se concentrations between 0 and 200 nM. The limit of detection is 0.01 nM Se when a deposition time of 15 min is used.     

Determination of aluminium in tree samples by cathodic adsorptive stripping voltammetry

This paper presents a method of determination of aluminium in tree samples (wood, leaves, roots) based on the cathodic adsorptive stripping voltammetry. Al(III) complexed with alizarin S was determined by ASV method using a hanging mercury drop electrode. Optimal conditions were found to be: accumulation time 30-90 s, accumulation potential - 0.70 V versus SCE, supporting electrolyte 0.1 M ammonia-ammonium chloride buffer at pH 8.2 and concentration of alizarin 1 x 10(-5) M. The response of the system, a linear current-concentration relationship was observed up to 8 x 10(-6) M. The developed method has been tested by analysing international reference materials (BCR 62 Olive leaves and BCR 101 spruce needles).     

The determination of some 2-thiobarbiturates by cathodic stripping voltammetry

Pulse polarography and cyclic voltammetry are employed in studies of the electrochemical behaviour of 5-ethyl-5'-(l-methylbutyl)-2-thiobarbituric acid (I), l-methyl-5-ethyl-5'-(l-methylpropyl)-2-thiobarbituric acid (II) and l,3-dimethyl-5-ethyl-5'-p-chlorophenyl)-2-thiobarbituric acid (III) in the pH range 4–12. All three compounds show anodic and cathodic waves or peaks in this pH range. Compounds (I) and (II) are oxidized at mercury indicator electrodes to produce mercury salts which can adsorb thereon and are thus amenable to cathodic stripping voltammetric analysis (c.s.v.) down to concentrations of the order of 10^-6 M, which is superior to the sensitivities obtained by differential pulse polarography (d.p.p.) based on a reduction peak. Compound (III) oxidizes to produce sulphur which is subsequently plated as HgS. Again the sensitivity of the c.s.v. method is of the order of lO^-6 M and analytically superior to d.p.p. The optimum pH for the three determinations is 8. The determination of (II) in the presence of its oxygenated analogue and metabolite, phemitone, and the effect of chloride ions are reported.     

Determination of selenium in freshwaters by cathodic stripping voltammetry after UV irradiation

An analytical method was developed for the determination of total dissolved selenium in fresh waters, using linear sweep cathodic stripping voltammetry (CSV) in combination with UV photolytic digestion. Both the CSV method, based on the electrodeposition and stripping of Cu(2)Se, and the UV irradiation procedure were investigated in detail. In the presence of dissolved organic substances, as in freshwaters, Se(VI) is reduced to Se(IV) by UV irradiation in 0.1M hydrochloric acid. Glucose can be used as the carbon source in samples low in natural dissolved organic carbon (DOC). The photolytic yields of Se(IV) were about 90% in both cases. Five freshwater samples were analysed for total selenium by CSV after UV photolysis, and by hydride generation atomic absorption spectrometry (HG-AAS) after oxidative digestion followed by reduction with hydrochloric acid. The results agreed well and the concentrations were in the range 70-190 ng/l., well above the detection limit of the CSV method at 2 ng/l.     

Determination of zinc by square-wave adsorptive stripping voltammetry using alizarin as a chelating agent

The adsorptive collection of zinc(II) complex with alizarin ligand, coupled with the square-wave voltammetric technique at the hanging mercury drop electrode, yields a very sensitive electroanalytical procedure for the determination of zinc. The optimized experimental conditions include: supporting electrolyte (carbonate buffer), pH (11), alizarin concentration (1 × 10^?6 mol l^?1), accumulation time (60 s), accumulation potential (?0.1 V), scan rate (700 mV s^?1), pulse amplitude (0.06 V) and SW frequency (80 Hz). The monitored stripping voltammetric current was linear over the range of 5 × 10^?8 – 4 × 10^?7 mol l^?1 and the detection limit was 1 × 10^?8 mol l^?1. The relative standard deviation was calculated as 1.3% (n = 10) for 1 × 10^?8 mol l^?1 Zn(II) and the obtained electrochemical signal was stabile for up to 60 min. Possible interferences by either co-existing metal ions or other chelating agents were also investigated. The applicability of the proposed SW-AdSV method to the analysis of foodstuff was assessed by the determination of zinc content in instant coffee samples. The accuracy of the obtained voltammetric analytical results was validated by comparing with that obtained by atomic absorption spectrometric method and conducting the necessary statistical evaluation.     

Differential pulse and square-wave cathodic stripping voltammetry of xanthine and xanthosine at a mercury electrode.

The surface activity of xanthine (Xan) and xanthosine (Xano) at a hanging mercury drop electrode (HMDE) was studied using out-of-phase ac and cyclic dc voltammetry. The results show that Xan and Xano were strongly adsorbed and chemically interacted with the charged mercury surface, which is the prerequisite step for applying the cathodic adsorptive stripping voltammetric determination of such biologically important compounds. Differential pulse cathodic adsorptive stripping voltammetry (DPCASV) and square-wave cathodic adsorptive stripping voltammetry (SWCASV) were applied for the ultratrace determination of Xan and Xano compounds. Moreover, a rapid and sensitive controlled adsorptive accumulation of Cu(II) complexes of both compounds provided the basis of a direct stripping voltammetric determination of such compounds to submicromolar and nanomolar levels. Operational and solution conditions for the quantitative ultratrace determination of Xan and Xano were optimized in absence and presence of Cu(II). The calibration curve data were subjected to least-squares refinements. The effects of several types of inorganic and organic interfering species on the determination of Xan or Xano were considered.     

Determination of arsenic by cathodic stripping voltammetry at a hanging mercury drop electrode

Arsenic (III), respectively arsenic(V) after the reduction were determined in model solutions and some inorganic and organic materials by fast scan differential pulse cathodic stripping voltammetry and by direct current cathodic stripping voltammetry with a rapid increase of potential. The accumulation on a hanging mercury drop electrode followed by cathodic stripping was carried out in 0.7–0.8M HCl or 1–2M H₂SO₄ solutions containing Cu(II)-ions. Detection limits calculated from regression parameters was determined to be under 1 ng/ml for the samples containing very low arsenic concentrations. The relative standard deviation did not reach 8% for arsenic contents about of 5 ng/ml.     

Determination of cadmium by cathodic stripping voltammetry in the presence of 4-phenylthiosemicarbazide

The electrochemical behavior of cadmium(II) is studied in the presence of 4-phenylthiosemicarbazide (4-PhTSC). It is found that the introduction of the phenyl radical into the thiosemicarbazide molecule enhances the sensitivity of cadmium determination by an order of magnitude and decreases the determination limit for cadmium(II) to 4 × 10^?9 M. The reagent is used to determine cadmium(II) in the surface water of the Prut River. The accuracy of the results is verified using standard solutions and concurrent determinations by AAS with atomization in a graphite furnace.     

Determination of trace europium by adsorptive cathodic stripping voltammetry after complexation with cupferron

This article describes the determination of Eu by adsorptive cathodic stripping voltammetry after complexation with N-nitroso-N-phenylhydroxylamine (cupferron). The accumulation of the complex at the HMDE was performed at 0.0 V and the subsequent potential scan was made in the square wave mode. The analyte signal occurred at −0.88 V. The detection limit is 0.06 nmol dm⁻³. The effect of instrumental and chemical parameters on the peak height and potential was investigated. The same technique can be used for the determination of ytterbium and of the other rare earth elements (REEs) after separation.