Microwave‐Assisted Synthesis of HKUST‐1 and Functionalized HKUST‐1‐@H3PW12O40: Selective Adsorption of Heavy Metal Ions in Water Analyzed with Synchrotron Radiation

A simple, rapid and efficient synthesis of the metal‐organic framework (MOF) HKUST‐1 [Cu₃(1,3,5‐benzene‐tri‐carboxilic‐acid)₂] by microwave irradiation is described, which afforded a homogeneous and highly selective material. The unusually short time to complete the synthesis by microwave irradiation is mainly attributable to rapid nucleation rather than to crystal growth rate. Using this method, HKUST‐1‐MW (MW=microwave) could be prepared within 20 min, whereas by hydrothermal synthesis, involving conventional heating, the preparation time is 8 h. Work efficiency was improved by the good performance of the obtained HKUST‐1‐MW which exhibited good selective adsorption of heavy metal ions, as well as a remarkably high adsorption affinity and adsorption capacity, but no adsorption of Hg²⁺ under the same experimental conditions. Of particular importance is the preservation of the structure after metal‐ion adsorption, which remained virtually intact, with only a few changes in X‐ray diffraction intensity and a moderate decline in surface area. Synthesis of the polyoxometalate‐containing HKUST‐1‐MW@H₃PW₁₂O₄₀ afforded a MOF with enhanced stability in water, due to the introduced Keggin‐type phosphotungstate, which systematically occluded in the cavities constituting the walls between the mesopores. Different Cu/W ratios were investigated according to the extrusion rate of cooper ions concentration, without significant structural changes after adsorption. The MOFs obtained feature particle sizes between 10–20 μm and their structures were determined using synchrotron‐based X‐ray diffraction. The results of this study can be considered important for potentially wider future applications of MOFs, especially to attend environmental issues.     

A Tale of Copper Coordination Frameworks: Controlled Single‐Crystal‐to‐Single‐Crystal Transformations and Their Catalytic CH Bond Activation Properties

Metal–organic frameworks (MOFs), as a class of microporous materials with well‐defined channels and rich functionalities, hold great promise for various applications. Yet the formation and crystallization processes of various MOFs with distinct topology, connectivity, and properties remain largely unclear, and the control of such processes is rather challenging. Starting from a 0D Cu coordination polyhedron, MOP‐1, we successfully unfolded it to give a new 1D‐MOF by a single‐crystal‐to‐single‐crystal (SCSC) transformation process at room temperature as confirmed by SXRD. We also monitored the continuous transformation states by FTIR and PXRD. Cu MOFs with 2D and 3D networks were also obtained from this 1D‐MOF by SCSC transformations. Furthermore, Cu MOFs with 0D, 1D, and 3D networks, MOP‐1, 1D‐MOF, and HKUST‐1, show unique performances in the kinetics of the C?H bond catalytic oxidation reaction.     

Expanded Organic Building Units for the Construction of Highly Porous Metal–Organic Frameworks

Two new organic building units that contain dicarboxylate sites for their self‐assembly with paddlewheel [Cu₂(CO₂)₄] units have been successfully developed to construct two isoreticular porous metal–organic frameworks (MOFs), ZJU‐35 and ZJU‐36, which have the same tbo topologies (Reticular Chemistry Structure Resource (RCSR) symbol) as HKUST‐1. Because the organic linkers in ZJU‐35 and ZJU‐36 are systematically enlarged, the pores in these two new porous MOFs vary from 10.8 Å in HKUST‐1 to 14.4 Å in ZJU‐35 and 16.5 Å in ZJU‐36, thus leading to their higher porosities with Brunauer–Emmett–Teller (BET) surface areas of 2899 and 4014 m² g^?1 for ZJU‐35 and ZJU‐36, respectively. High‐pressure gas‐sorption isotherms indicate that both ZJU‐35 and ZJU‐36 can take up large amounts of CH₄ and CO₂, and are among the few porous MOFs with the highest volumetric storage of CH₄ under 60 bar and CO₂ under 30 bar at room temperature. Their potential for high‐pressure swing adsorption (PSA) hydrogen purification was also preliminarily examined and compared with several reported MOFs, thus indicating the potential of ZJU‐35 and ZJU‐36 for this important application. Studies show that most of the highly porous MOFs that can volumetrically take up the greatest amount of CH₄ under 60 bar and CO₂ under 30 bar at room temperature are those self‐assembled from organic tetra‐ and hexacarboxylates that contain m‐benzenedicarboxylate units with the [Cu₂(CO₂)₄] units, because this series of MOFs can have balanced porosities, suitable pores, and framework densities to optimize their volumetric gas storage. The realization of the two new organic building units for their construction of highly porous MOFs through their self‐assembly with [Cu₂(CO₂)₄] units has provided great promise for the exploration of a large number of new tetra‐ and hexacarboxylate organic linkers based on these new organic building units in which different aromatic backbones can be readily incorporated into the frameworks to tune their porosities, pore structures, and framework densities, thus targeting some even better performing MOFs for very high gas storage and efficient gas separation under high pressure and at room temperature in the near future.     

Hierarchical Mesoporous Metal–Organic Frameworks for Enhanced CO2 Capture

Hierarchical porous materials are promising for catalyst, separation and sorption applications. A ligand‐assisted etching process is developed for template‐free synthesis of hierarchical mesoporous MOFs as single crystals and well‐intergrown membranes at 40 °C. At 223 K, the hierarchical porous structures significantly improve the CO₂ capture capacity of HKUST‐1 by more than 44 % at pressures up to 20 kPa and 13 % at 100 kPa. Even at 323 K, the enhancement of CO₂ uptake is above 25 % at pressures up to 20 kPa and 7 % at 100 kPa. The mesoporous structures not only enhance the CO₂ uptake capacity but also improve the diffusion and mass transportation of CO₂. Similarly, well‐intergrown mesoporous HKUST‐1 membranes are synthesized, which hold the potential for film‐like porous devices. Mesoporous MOF‐5 crystals are also obtained by a similar ligand‐assisted etching process. This may provide a facile way to prepare hierarchical porous MOF single crystals and membranes for wide‐ranging applications.     

Water‐Stable Zirconium‐Based Metal–Organic Framework Material with High‐Surface Area and Gas‐Storage Capacities

We designed, synthesized, and characterized a new Zr‐based metal–organic framework material, NU‐1100 , with a pore volume of 1.53 ccg^?1 and Brunauer–Emmett–Teller (BET) surface area of 4020 m²g^?1; to our knowledge, currently the highest published for Zr‐based MOFs. CH₄/CO₂/H₂ adsorption isotherms were obtained over a broad range of pressures and temperatures and are in excellent agreement with the computational predictions. The total hydrogen adsorption at 65 bar and 77 K is 0.092 g g^?1, which corresponds to 43 g L^?1. The volumetric and gravimetric methane‐storage capacities at 65 bar and 298 K are approximately 180 v_STP/v and 0.27 g g^?1, respectively.     

Effect of the Ethanol/BTC Ratio on the Methane Uptake of Mechanochemically Synthesized MOF-199

We report on a detailed textural analysis of mechanochemically synthesized MOF-199 including N₂ adsorption-desorption and CO₂ adsorption isotherms data at 77 K and 273 K (up to atmospheric pressure), respectively, and CH₄ adsorption data at 298 K (up to 35 bar). We used the isotherm adsorption data to determine the micropore volume of the MOF-199 structures, to establish their methane uptake capacity and to understand how these properties depended on the Ethanol/BTC ratio used during the synthesis. The maximum methane uptake capacity for our specimens was recorded at 130 v/v at 35 bars. These results open an avenue for a better understanding of alternative manufacturing processes of MOF structures for gas storage applications.     

Surface‐Anchored MOF‐Based Photonic Antennae

The loading of a metal‐organic framework (MOF), [Cu₃(btc)₂xH₂O] HKUST‐1, with europium β‐diketonate complexes is studied with the goal to using the porous molecular framework as a photonic antenna. Whereas loading of HKUST‐1 powder particles produced via the conventional solvothermal synthesis method was strongly hindered, for HKUST‐1 SURMOFs, thin MOF films fabricated using the liquid phase epitaxy method, a high filling factor can be achieved. The optical properties of the HKUST‐1‐MOFs before and after loading were analysed with the aid of luminescence spectroscopy. Careful analysis of the absorption spectra reveals the presence of an effective energy transfer between the HKUST‐1 framework and the Eu³⁺ centers.     

A Spiderweb‐Like Metal–Organic Framework Multifunctional Foam

Processing metal–organic frameworks (MOFs) into hierarchical macroscopic materials can greatly extend their practical applications. However, current strategies suffer from severe aggregation of MOFs and limited tuning of the hierarchical porous network. Now, a strategy is presented that can simultaneously tune the MOF loading, composition, spatial distribution, and confinement within various bio‐originated macroscopic supports, as well as control the accessibility, robustness, and formability of the support itself. This method enables the good dispersion of individual MOF nanoparticles on a spiderweb‐like network within each macrovoid even at high loadings (up to 86 wt %), ensuring the foam pores are highly accessible for excellent adsorption and catalytic capacity. Additionally, this approach allows the direct pre‐incorporation of other functional components into the framework. This strategy provides precise control over the properties of both the hierarchical support and MOF.     

Metal-organic frameworks with exceptionally high capacity for storage of carbon dioxide at room temperature

Metal-organic frameworks (MOFs) show high CO2 storage capacity at room temperature. Gravimetric CO2 isotherms for MOF-2, MOF-505, Cu3(BTC)2, MOF-74, IRMOFs-11, -3, -6, and -1, and MOF-177 are reported up to 42 bar. Type I isotherms are found in all cases except for MOFs based on Zn4O(O2C)6 clusters, which reveal a sigmoidal isotherm (having a step). The various pressures of the isotherm steps correlate with increasing pore size, which indicates potential for gas separations. The amine functionality of the IRMOF-3 pore shows evidence of relatively increased affinity for CO2. Capacities qualitatively scale with surface area and range from 3.2 mmol/g for MOF-2 to 33.5 mmol/g (320 cm3(STP)/cm3, 147 wt %) for MOF-177, the highest CO2 capacity of any porous material reported.     

Lithium‐Functionalized Metal–Organic Frameworks that Show >10 wt % H2 Uptake at Ambient Temperature

We have used grand canonical Monte Carlo simulations with a first‐principles‐based force field to show that metal–organic frameworks (MOFs) with Li functional groups (i.e. C? Li bonds) allow for exceptional H₂ uptake at ambient temperature. For example, at 298 K and 100 bar, IRMOF‐1‐4Li shows a total H₂ uptake of 5.54 wt % and MOF‐200‐27Li exhibits a total H₂ uptake of 10.30 wt %, which are much higher than the corresponding values with pristine MOFs. Li‐functionalized MOF‐200 (MOF‐200‐27Li) shows 11.84 wt % H₂ binding at 243 K and 100 bar. These hydrogen‐storage capacities exceed the 2015 DOE target of 5.5 wt % H₂. Moreover, the incorporation of Li functional groups into MOFs provides more benefits, such as higher delivery amount, for H₂ uptake than previously reported Li‐doped MOFs.     

Ultrahigh CO2 adsorption capacity on carbon molecular sieves at room temperature

Although metal-organic framework (MOF) materials have been postulated as superior to any other sorbent for CO(2) adsorption at room temperature, here we prove that the appropriate selection of the raw material and the synthesis conditions allows the preparation of carbon molecular sieves (CMSs) with adsorption capacity, on a volumetric basis, highly exceeding those reported in the literature for MOFs. Furthermore, the excellent sorption properties of CMSs over the whole pressure range (up to 50 bar) are fully reversible after different adsorption/desorption cycles.     

多孔金属有机骨架材料储氢性能分子模拟

采用优化的DREIDING力场参数, 通过巨正则系综蒙特卡洛(GCMC)模拟方法对H₂在IRMOF-1、IRMOF-61和IRMOF-62共3种金属有机骨架(MOFs)材料中的吸附平衡性能进行了比较研究. 结果表明, 该力场能够在全压力范围内很好地复制H₂在IRMOF-62材料中的等温吸附曲线; 但对低压下H₂在IRMOF-61中的等温吸附曲线预测出现低估. 与IRMOF-1相比, 具有互穿骨架结构的IRMOF-61和IRMOF-62材料在常温下的储氢能力并无明显提高. 进一步比较77 K时100 kPa、3.0 MPa下H₂在上述MOFs材料中达到吸附平衡时的几率密度分布发现, H₂会优先吸附在Zn₄O骨架附近靠近苯环的位置;对具有互穿结构的MOFs材料而言,由于其孔腔尺寸缩小, 使得H₂优先吸附位区域零散化. 适当长度的有机配体形成的互穿骨架结构能增强与H₂分子之间的相互作用, 具备较高的储氢能力; 而有机配体尺寸过长则会增加骨架结构中H₂吸附死角, 对H₂的吸附能力反而出现下降.     

Multiple Active Sites: Lithium Storage Mechanism of Cu‐TCNQ as an Anode Material for Lithium‐Ion Batteries

Recently, carboxylate metal‐organic framework (MOF) materials were reported to perform well as anode materials for lithium‐ion batteries (LIBs); however, the presumed lithium storage mechanism of MOFs is controversial. To gain insight into the mechanism of MOFs as anode materials for LIBs, a self‐supported Cu‐TCNQ (TCNQ: 7,7,8,8‐tetracyanoquinodimethane) film was fabricated via an in situ redox routine, and directly used as electrode for LIBs. The first discharge and charge specific capacities of the self‐supported Cu‐TCNQ electrode are 373.4 and 219.4 mAh g^?1, respectively. After 500 cycles, the reversible specific capacity of Cu‐TCNQ reaches 280.9 mAh g^?1 at a current density of 100 mA g^?1. Mutually validated data reveal that the high capacity is ascribed to the multiple‐electron redox conversion of both metal ions and ligands, as well as the reversible insertion and desertion of Li⁺ ions into the benzene rings of ligands. This work raises the expectation for MOFs as electrode materials of LIBs by utilizing multiple active sites and provides new clues for designing improved electrode materials for LIBs.     

Molecular simulation of adsorption and diffusion of hydrogen in metal-organic frameworks

Metal-organic frameworks (MOFs) are thought to be a set of promising hydrogen storage materials; however, little is known about the interactions between hydrogen molecules and pore walls as well as the diffusivities of hydrogen in MOFs. In this work, we performed a systematic molecular simulation study on the adsorption and diffusion of hydrogen in MOFs to provide insight into molecular-level details of the underlying mechanisms. This work shows that metal-oxygen clusters are preferential adsorption sites for hydrogen in MOFs, and the effect of the organic linkers becomes evident with increasing pressure. The hydrogen storage capacity of MOFs is similar to carbon nanotubes, which is higher than zeolites. Diffusion of hydrogen in MOFs is an activated process that is similar to diffusion in zeolites. The information derived in this work is useful to guide the future rational design and synthesis of tailored MOF materials with improved hydrogen adsorption capability.     

Evaluation of defect induced surface heterogeneity in Metal-Organic Framework materials with alkali dopants employing adsorption isotherm modelling

In this article, an assessment of surface structural heterogeneity in porous metal organic framework (MOF) structure has been demonstrated by employing the methane and carbon-dioxide adsorption isotherms data. The virgin MIL-101-(Cr) MOF was synthesized by the hydrothermal method and defects were induced in the MOF structure by doping with various alkali (K, Na, Li) cations. The synthesized MOFs were characterized by XRD, SEM, EDX and BET measurement techniques. In order to understand the defect induced surface heterogeneity by alkali cation dopants, the surface energy distributions for CH₄ and CO₂ adsorptions on MOFs were measured by Dubinin – Astakhov model equation. The surface heterogeneity is mainly controlled by the limiting uptakes of adsorbates, the polarizability of adsorbates and the adsorbate-adsorbent interaction energy.     

Molecular screening of metal-organic frameworks for CO2 storage

We report a molecular simulation study for CO2 storage in metal-organic frameworks (MOFs). As compared to the aluminum-free and cation-exchanged ZSM-5 zeolites and carbon nanotube bundle, IRMOF1 exhibits remarkably higher capacity. Incorporation of Na(+) cations into zeolite increases the capacity only at low pressures. By variation of the metal oxide, organic linker, functional group, and framework topology, a series of isoreticular MOFs (IRMOF1, Mg-IRMOF1, Be-IRMOF1, IRMOF1-(NH2)4, IRMOF10, IRMOF13, and IRMOF14) are systematically examined, as well as UMCM-1, a fluorous MOF (F-MOF1), and a covalent-organic framework (COF102). The affinity with CO2 is enhanced by addition of a functional group, and the constricted pore is formed by interpenetration of the framework; both lead to a larger isosteric heat and Henry's constant and subsequently a stronger adsorption at low pressures. The organic linker plays a critical role in tuning the free volume and accessible surface area and largely determines CO2 adsorption at high pressures. As a combination of high capacity and low framework density, IRMOF10, IRMOF14, and UMCM-1 are identified from this study to be the best for CO2 storage, even surpass the experimentally reported highest capacity in MOF-177. COF102 is a promising candidate with high capacity at considerably low pressures. Both gravimetric and volumetric capacities at 30 bar correlate well with the framework density, free volume, porosity, and accessible surface area. These structure-function correlations are useful for a priori prediction of CO2 capacity and for the rational screening of MOFs toward high-efficacy CO2 storage.     

Block Copolymer‐Templated Approach to Nanopatterned Metal–Organic Framework Films

The fabrication of patterned metal–organic framework (MOF) films with precisely controlled nanoscale resolution has been a fundamental challenge in nanoscience and nanotechnology. In this study, nanopatterned MOF films were fabricated using a layer‐by‐layer (LBL) growth method on functional templates (such as a bicontinuous nanoporous membrane or a structure with highly long‐range‐ordered nanoscopic channels parallel to the underlying substrate) generated by the microphase separation of polystyrene‐b ‐poly(2‐vinylpyridine) (PS‐b ‐P2VP) block copolymers. HKUST‐1 can be directly deposited on the templates without any chemical modification because the pyridine groups in P2VP interact with metal ions via metal‐BCP complexes. As a result, nanopatterned HKUST‐1 films with feature sizes below 50 nm and controllable thicknesses can be fabricated by controlling the number of LBL growth cycles. The proposed fabrication method further extends the applications of MOFs in various fields.     

Advances of Metal‐Organic Frameworks in Energy and Environmental Applications

Nowadays, energy shortage and environmental pollution issues are increasingly severe and urgent to be solved. The effective storage and use of environmentally friendly fuels and removal of harmful gases from the environment are great challenges and of great importance both for the environment protection and for human health. Porous metal‐organic frameworks (MOFs) are highly ordered crystalline materials formed by the self‐assembly process of metal ions and organic ligands. Their good features such as ultrahigh porosity, large surface area, structural diversity and functionalities make them promising candidates for applications in energy and environmental fields. MOF thin films and MOF composites have also been investigated to further enhance the properties and introduce new functionalities. This review provides an overview of the synthesis methods of pristine MOFs, MOF thin films and MOF composites, and significant advances of MOFs in energy and environment applications such as energy storage (H₂, CH₄), CO₂ capture and separation, adsorption removal and sensing of harmful gases in the environment.     

Effect of Central Metal Ions of Analogous Metal–Organic Frameworks on Adsorption of Organoarsenic Compounds from Water: Plausible Mechanism of Adsorption and Water Purification

The adsorptive removal of organoarsenic compounds such as p‐arsanilic acid (ASA) and roxarsone (ROX) from water using metal–organic frameworks (MOFs) has been investigated for the first time. A MOF, iron benzenetricarboxylate (also called MIL‐100‐Fe) exhibits a much higher adsorption capacity for ASA and ROX than activated carbon, zeolite (HY), goethite, and other MOFs. The adsorption of ASA and ROX over MIL‐100‐Fe is also much more rapid than that over activated carbon. Moreover, the used MIL‐100‐Fe can be recycled by simply washing with acidic ethanol. Therefore, it is determined that a MOF such as MIL‐100‐Fe can be used to remove organoarsenic compounds from contaminated water because of its high adsorption capacity, rapid adsorption, and ready regeneration. Moreover, only one of three analogous MIL‐100 species (MIL‐100‐Fe, rather than MIL‐100‐Al or MIL‐100‐Cr) can effectively remove the organoarsenic compounds. This selective and high adsorption over MIL‐100‐Fe, different from other analogous MIL‐100 species, can be explained (through calculations) by the facile desorption of water from MIL‐100‐Fe as well as the large (absolute value) replacement energy (difference between the adsorption energies of the organoarsenic compounds and water) exhibited by MIL‐100‐Fe. A plausible adsorption/desorption mechanism is proposed based on the surface charge of the MOFs, FTIR results, calculations, and the reactivation results with respect to the solvents used in the experiments.     

Cooperative effect of temperature and linker functionality on CO2 capture from industrial gas mixtures in metal-organic frameworks: a combined experimental and molecular simulation study

In this work, the cooperative effect of temperature and linker functionality on CO(2) capture in metal-organic frameworks (MOFs) was investigated using experimental measurements in combination with molecular simulations. To do this, four MOFs with identical topology but different functional groups on the linkers and three important CO(2)-containing industrial gas mixtures were adopted. The interplay between linker functionality and temperature was analyzed in terms of CO(2) storage capacity, adsorption selectivity, working capacity of CO(2) in temperature swing adsorption (TSA) processes, as well as sorbent selection parameter (S(ssp)). The results show that the effect of linker functionality on CO(2) capture performance in the MOFs is strongly interconnected with temperature: up to moderate pressures, the lower the temperature, the larger the effect of the functional groups. Furthermore, the modification of a MOF by introducing more complex functional groups can not only improve the affinity of framework for CO(2), but also reduce the free volume, and thus may contribute negatively to CO(2) capture capability when the packing effect is obvious. Therefore, when we design a new MOF for a certain CO(2) capture process operated at a certain temperature, the MOF should be designed to have maximized affinity for CO(2) but with a negligible or small effect caused by the reduction of free volume at that temperature and the corresponding operating pressure.